Shop by vehicle

Lifting suspension from TREKFINDER for SUZUKI Jimny II type GJ from 10/2018 / HJ - the lift is approx. 40-50 millimetres Suitable for model / vehicles:Jimny type GJ from 2018 > / HJdepending on variant: with / without installed cable winch in front depending on variant: with / without steel braided brake line setwith or without LED light with manual transmissionwith automatic transmissionwith 1,5 L engine 75 Kwwith axle loads VA 680 Kg / HA 880 Kgwith ABE-EG number: e6*2007/46*0253*.. oder e6*2007/46*0515*.. SCOPE OF DELIVERY 1-SUJI2F1: 2 pieces TREKFINDER coil spring front axle, progressive wound, Made by H&R®.2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R®.2 pieces TREKFINDER shock absorber front axle, monotube gas pressure B6, Made by BILSTEIN®2 pieces TREKFINDER shock absorber rear axle, monotube gas pressure B6, Made by BILSTEIN®4 pieces TREKFINDER steel braided brake line, stainless steel & protective jacket, Made by LUCAS GIRLING®1 piece TREKFINDER mounting kit for models with LED headlight1 piece TREKFINDER TÜV® parts certificate SCOPE OF DELIVERY 1-SUJI2F2: 2 pieces TREKFINDER coil spring front axle, linear wound, Made by H&R®.2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R®.2 pieces TREKFINDER shock absorber front axle, monotube gas pressure B6, Made by BILSTEIN®2 pieces TREKFINDER shock absorber rear axle, monotube gas pressure B6, Made by BILSTEIN®4 pieces TREKFINDER steel braided brake line, stainless steel & protective jacket, Made by LUCAS GIRLING®1 piece TREKFINDER mounting kit for models with LED headlight1 piece TREKFINDER TÜV® parts certificate SCOPE OF DELIVERY 1-SUJI2F3: 2 pieces TREKFINDER coil spring front axle, progressive wound, Made by H&R®.2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R®.2 pieces TREKFINDER shock absorber front axle, monotube gas pressure B6, Made by BILSTEIN®2 pieces TREKFINDER shock absorber rear axle, monotube gas pressure B6, Made by BILSTEIN®1 piece TREKFINDER mounting kit for models with LED headlights1 piece TREKFINDER TÜV® parts certificate SCOPE OF DELIVERY 1-SUJI2F4: 2 pieces TREKFINDER coil spring front axle, linear wound, Made by H&R®.2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R®.2 pieces TREKFINDER shock absorber front axle, monotube gas pressure B6, Made by BILSTEIN®2 pieces TREKFINDER shock absorber rear axle, monotube gas pressure B6, Made by BILSTEIN®1 piece TREKFINDER mounting kit for models with LED headlights1 piece TREKFINDER TÜV® parts certificate Translated with www.DeepL.com/Translator (free version)

Highest load capacity This kit consists of two half shafts, two CV joints and two heavy-duty drive flanges. The Raptor Heavy Duty front shafts are made from SAE4340 Nickel Chromoly alloy steel, that provide the optimum level of strength and flex when heat-treated. They have the ability to twist without breaking as well as extremely high fatigue resistance, which enables the shafts to tolerate repeated shock loading. This ability to flex without breaking also helps protecting other drivetrain components. All shafts are 24 spline and primarily suited to post 1994 axles, although they can be fitted to earlier vehicles with additional work. Please note that MY2002 vehicles have been delivered with both types of rear axle - please check which axle has been fitted to your vehicle. Please choose your axle type. The shafts are for following vehicle models:HSVOKIT-ABS: for 90/110/130 Defender, Discovery 1 and Range Rover Classic 1994 on WITH ABS CV JOINTSHSVOKIT-STD: for 90/110/130 Defender, Discovery 1 und Range Rover Classic 1994 on NON ABS CV JOINTS

Cable winch set for Lada Niva / Taiga, including complete installation set The extremely robust bumper fits the original stops on the Lada.Now you have not only a winch holder, but a massive, shapely steel bumper, which was kept in the original design. The powder-coated bumper has a shackle holder (shackle included) and pickup points for a Farm Jack jack. ***Important!****Since the original alternator and the Lada battery are very small, we recommend one Upgrade at least the battery. Ask your Lada dealer about the possibilities. NOT SUITABLE FOR A LADA BRONTO with plastic bumper! In the version with aluminum bumper, the system fits! The grille must be cut out for new Ladas! WITH TÜV AND PARTIAL APPROVAL FOR GERMANY! The certificate applies to vehicles up to the year of construction: see below! Technical specifications: Engine:Motor: 3.8kW / 5.1 HPMotor type: Series wound motor (the magnetic field is generated electrically)Maximum power consumption: 320 ampsVoltage: 12 volts Transmission:Reduction: 166 : 13-stage planetary gear General data:Max pulling force: 3600 kgMaximum train speed: 5,5 m / min (measured without load)Plastic rope (diameter x length): 10 mm x 30 mDrum (diameter x length): 63 x 227 mmOverall size (LxWxH): 570 x 180 x 243 mmWeight winch 29 kgWeight installation set 21 kgOverrunning clutch (decoupling the gearbox to unwind the rope by hand) Included accessories:cable remote controlfairleadmounting screwsoperation manualhookBumpers spacers TÜV certificate for the following vehicles: Vehicle type         ABE / EG-BE no.         Variant / version212140                  e2 * 93/81 * 0183 * ..                 all212140                  e2 * 98/14 * 0051 * ..                 all21214                    e1 * KS * 0004 * ..                     all2121A                   e1 * KS * 0008 * ..                      all2121                     e2 * 98/14 * 0183 * ..                 all2121                    e2 * 2001/116 * 0260 * ..            all2121 **** DA        e2 * 2001/116 * 0326 * ..            all2121DE               e1 * KS07 / 46 * 0021 * ..           allM2121                 e2 * KS07 / 46 * 0011 * ..           allN2121                 e2 * KS07 / 46 * 0012 * ..           allMU2121                 e2*KS07/46*0056*                 allMU2121                e2*KS07/46*0076*                  all      M2131                e2 * KS07 / 46 * 0077 * ..           all

Garrett Turbocharger for Land Rover Defender Td5 and Discovery 2 Replacement for the original turbocharger of the Land Rover Defender TD5 2.5 or Discovery II 2.5

Heavy Duty Cardan shaft - Land Rover Defender Tdi / Td5 Heavy Duty GKN Prop Shaft - front axle - with centred double joint and flange assembly, for Land Rover Defender. GKN double joint prop shaft, fits Defender 90/110/130, for Tdi and Td5 up to MY07, with flange assembly. This heavy duty prop shaft is recommended for vehicles with body lift or as a replacement for a failed prop shaft. For steady,  smooth driving even with high articulation angle. Comes with suitable flange assembly with seals etc. for transfer case.

Abenteuer4x4 - Rockslider - for Land Rover Defender The stainless steel Rockslider by Abenteuer 4x4 for the Land Rover Defender 90/110/130CC convince by a completely new design, low weight (approx. 12 kg/piece) and an easy mounting without drilling.To increase rigidity, two webs are welded on the back and the slotted holes on the long side are turned inwards.The Rocksliders not only serve to protect the bodywork, but also provide a secure foothold thanks to their non-slip surface made of drawn knobs, and their shape also protects against excessive dirt in the field. There are several openings on the underside for rinsing out dirt that has been picked up.The Rocksliders - made in Germany - are powder-coated black. Delivery includes fixing material.This item is bulky goods.Material: stainless steel, black powder coatedMaterial thickness: 3mm Delivery: 1 set Rockslider stainless steel (left & right)Bracket and fixing materialSet of screws stainless steel As a useful add-on, there are matching anti-slip pads for the Rockslider.You can find a suitable crossbar here.

Lifting suspension by TREKFINDER for SUZUKI Jimny I Type FJ|the lifting is approx. 55 millimetres SUPPLY: 1-SUJIF1.1 BILSTEIN - not hardness adjustable - very tight tuning 2 pieces TREKFINDER coil spring front axle, progressively wound, Made by H&R 2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R 2 pieces TREKFINDER shock absorber front axle, B6 not adjustable, Made by BILSTEIN 2 pieces TREKFINDER shock absorber rear axle, B6 not adjustable, Made by BILSTEIN 4 pieces TREKFINDER steel braided brake line, stainless steel & protective jacket, Made by ZF/LUCAS GIRLING 1 piece TREKFINDER TÜV® parts certificate SUPPLY 1-SUJIF1.2: KONI - height adjustable - comfortable to very tight tuning possible 2 pieces TREKFINDER coil spring front axle, progressively wound, Made by H&R 2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R 2 pieces TREKFINDER shock absorber front axle, heavy track 5-way adjustable, Made by KONI 2 pieces TREKFINDER shock absorber rear axle, Heavy Track 5-way adjustable, Made by KONI 4 pieces TREKFINDER steel braided brake line, stainless steel & protective jacket, Made by ZF/LUCAS GIRLING 1 piece TREKFINDER TÜV® parts certificate Info KONI: The suspension or dampers are delivered from the factory in the most comfortable damper setting ( open ). Ideal for vehicles that are driven daily on and off the road without additional weights. Fine damping of bumps, asphalt edges, holes, curbs etc. WITHOUT being spongy. WITHOUT being spongy! For applications and wishes that make a harder shock absorber sensible (e.g. roof rack, cable winch, camping equipment etc.), 5 hardness levels are available with the KONI shock absorber in order to be able to individually tighten the shock absorber! The levels are clearly noticeable when driving. In our opinion, there is a suitable set-up for every application. OPTIONAL additionally available:- for level compensation and can be mounted once per spring, the TREKFINDER spring spacer rings 10 mm with Art. No. 1-FDR10- the reinforced steering damper from TREKFINDER with the Art. No. 1-SUJILD.1  

Heavy Duty Cardan shaft Heavy Duty GKN Prop Shaft - front axle - with centred double joint and flange assembly for Defender 90/110/130, Td4 from MY07. This heavy duty prop shaft is recommended for vehicles with body lift or as a replacement for a failed prop shaft. For steady,  smooth driving even with high articulation angle. Comes with suitable flange assembly with seals etc. for transfer case.

High quality Nakatanenga crossbars for Land Rover Defender Who does not need an entire roof rack on his Land Rover Defender, because just want to mount a roof tent on two cross-beams, for which the Nakatanenga CargoBear crossbars are optimally suited! They are identical to the crossbars of the CargoBear roof rack and therefore combine all their advantages: made of a light and stable aluminum-magnesium alloy (AlMg3) high quality powder coated (RAL 9005 - deep black) width: 1.450 mm (of which 1.300 mm for the usable area) length: 120 mm completely made in Germany Furthermore, two or three brackets can be upgraded by buying the missing parts to a full CargoBear roof rack - this is just the advantage of the modular system carrier! Of course, numerous accessories for the CargoBear roof rack with the crossbars can be used. Please note: The CargoBear roof rack / crossbar can not be installed on defenders that have a ribbed roof (see photo). An approximate indication of the series is between 1983 and 1989. Installation note:M10 lens head: 20 Nm to 25 NmM6 lens cylinder head: 10 Nm to 12 Nm Measured from the gutter, the Cargobear is approx. 23 cm high. On the roof it is approx. 5-6 cm - depending on the roof, condition, year of construction etc.

TREKFINDER complete protection for Suzuki Jimny II (GJ/HJ) - 5 parts, full safety suitable for all Jimny models of the type GJ built from the end of  2018, Typ HJ suitable for all engine and transmission types including all mounting parts attachment to original points of the vehicle super stable and flat heavy duty versions Delivery: underride protection linkage 5 mm anodised aluminum underrun protection axle tube / differential front axle 5 mm galvanized steel underride protection transfer case 8 mm aluminum underride protection exhaust gas control system 3 mm galvanized steel underrun protection axle tube / differential rear axle 5 mm galvanized steel

Nakatanenga CargoBear - crossbar - for Mercedes G Who does not need an entire roof rack on his Mercedes G because he e.g. If you only want to install a roof tent on two crossbars, the CargoBear cross bars are ideal for that! They are structurally identical to the crossbars of the CargoBear Mercedes G roof racks and therefore also offer their advantages: made of a light and stable aluminum-magnesium alloy (AlMg3) high quality powder-coated (RAL 9005 - jet black) width: 1.505 mm (thereof 1.350 mm for the usable area) length: 120 mm completely made in Germany Since our CargoBear roof racks are modular system racks, you can upgrade two or three brackets to the full roof rack by purchasing the missing parts! Of course, numerous accessories can also be used for the CargoBear roof rack with the crossbars. Installation note:M10 lens head: 20 Nm to 25 NmM6 lens cylinder head: 10 Nm to 12 Nm Measured from the gutter, the CargoBear is approx. 20cm high. On the roof it is approx. 5-6 cm - depending on the roof, condition, year of construction etc. Suitable for all CargoBear 1 + 2 roof racks!

VNT EXTREMEspec TD5 Solid Mass Flywheel Kit LOF Clutches’ goal was to deliver the best Solid Mass Flywheel kit for Td5 Discovery and Defender. They have engineered this product with two specific objectives: first, to prevent the typical vibrations for Td5 and second, to guarantee long lasting service from clutch and flywheel. At LOF, EXTREMEspec stands for the ultimate Land Rover clutches! If ROADspec and POWERspec are not enough for your demands, because your Landy is destined for extreme performance in work and play, you will not find anything better than LOF EXTREMEspec clutches. They combine unbeatable performance and everyday handling for all Td5 Discovery and Defender-Models with the original dual mass flywheel. And by the way, the pedal weight is not heavier than the original. Dual mass flywheels are prone to overheating in tuned vehicles with remapped engines or when the clutch has to deal with a lot of heavy towing or extreme conditions. Replacing DMFs with solid mass flywheels will prevent thermal damage. LOF’s solid mass flywheels conform to the characteristics of the original flywheels but are much more reliable, durable and even cheaper than components by Valeo or LUK. LOF are testing their replacement kits with leading Land Rover tuning specialists in the UK and Europe. Perfect for vehicles with a Stage3 map/ 550Nm / 250 bhp (VNT turbo compatible).  Description: LOF heavy duty friction material LOF extra strong clutch cover 1x 3 stage pre-dampened sprung driven plate 1x LOF solid flywheel 1x LOF Td5 clutch cover 1x LOF EXTREMEspec heavy duty release bearing 1x G90 high-temp assembly grease 6x clutch cover bolts 1x CNC wire-formed anti-rattle wire spring clip 1x CNC wire-formed pushrod clip 1x spigot bush OEM 1x fork bush OEM 8x flywheel bolts Pedal weight not heavier than original  You can find more products for improved clutch performance here: clutch spring Note from LOF: if this clutch is newly installed, the LOF Powermaster clutch master cylinder and the LOF clutch slave cylinder should not be installed as well! Legal notice: Due to technical changes, noise may be generated. This is technically harmless and therefore no reason for complaint! Installation at your own risk without guarantee for damage to the gearbox and drive train.

GRP hood “Puma” with air intake he hood for all Land Rover Defender 90/110/130 (all series, TDi / TD5 / TD4 2.4 / TD4 2.2) is made of fiberglass plastic, saves weight (only approx. 15 kg) and is optionally equipped with an air intake that contributes to cooling. It is fitted with a grille that corresponds to our “Heritage Style” radiator grille. The hood is supplied unpainted. The fastening elements of the original hood are used. It is compatible with our anti-theft hood hinges.    

Various sets of door hinges for Mercedes Benz G-Class Many owners of the G-Class know the problem only too well: the original door hinges start to rust, the paint flakes off and the doors become increasingly difficult to open and close. This is exactly where we come in - with a long-lasting solution: high-quality door hinges made of high-strength aluminium offer optimum protection against rust and corrosion thanks to a special surface finish.The centrepiece of the design is a tried-and-tested stainless steel pin with a milled spiral groove that distributes the grease ideally. Thanks to the integrated grease nipple, the hinges can be easily re-greased at any time. Of course, we also supply everything you need for installation.Advantages with the Offroad Monkeys door hinges for the G-Class: Suitable for Mercedes G 460 / 461 / 463 up to model year 2018  Available for 2- and 4-door models - or individually for one door  No rusting, no more jamming - Made of high-strength aluminium  precise and robust  Corrosion and UV-resistant thanks to special coating  Lubricatable via integrated grease nipple  Stainless steel plain bearing replaceable  Stainless steel bolts with spiral groove for even grease distribution  Plastic washers included to protect against contact corrosion  Registered design  Paintable & can be completely dismantled  100% Made in Germany Door hingeSet for only one door (left or right)  Suitable for the respective side  front and rear  Contains 2 door hinges  Includes precisely fitting seals and all necessary stainless steel screws Door hinge set for 2-door G-Class Contains 4 door hinges  With matching seals and stainless steel screws Door hinge set for 4-door G-Class  Contains 8 door hinges  With matching seals and stainless steel screws Tools for easy removal of the catch bolts can be found here.The matching window hinges, rear door hinges and bonnet hinges for the Mercedes G are also available from us.

Centre hole adapter for Hutchinson G/Pinzgauer rim on Defender Bolt circle adapter for running the Hutchinson WA-0491 (Pinzgauer) beadlock rim on the Land Rover Defender. The adapter set is also available for the Hutchinson WA-0492 (Mercedes G) on request - please contact us. Supplied with mounting material and strength certificate - with this certificate, registration is possible via individual approval. The adapter widens the track by 65 mm on each side, totalling 130 mm. Together with the Pinzgauer rim, this results in a practical press-in depth ET -2. The set consists of 5 adapters (2 axles + spare wheel), the required fastening material and the strength certificate.    

Land Rover rear bumper / trailer hitch / rear step for Defender 110 With E-mark, for mounting a ball head, E-set and ball head not included, compatible with Nakatanenga spare wheel carrier. Suitable for Land Rover Defender 110 from MY 1998-2016 (TD5 and TD4)

HD Side Steps / Rock Sliders for the Land Rover New Defender L663 (Model Year 2020 and later) The Land Rover New Defender L663 is a modern travel vehicle, workhorse, and off-roader all in one. Especially when the New Defender is driven off paved roads, the side sills are particularly vulnerable: deep ruts, rocks, embankments, or side impacts can quickly cause damage to the body and underbody. These HD Side Steps were developed to effectively protect precisely these areas while also making the New Defender more practical for everyday use.   These sturdy rock sliders protect the vehicle’s sides during challenging off-road adventures and also serve as a robust step. As rock sliders and side sill protectors, they provide additional protection for the side body panels and sill areas—especially during off-road driving, travel, and expeditions. At the same time, they make it easier to get in and out of the vehicle and to access roof racks, roof tents, roof boxes, or awnings.   The side steps are manufactured from sturdy structural steel. The components are laser-cut and CNC-bent, ensuring a precise fit, robust construction, and durable design. For long-lasting protection against corrosion, weather, and mechanical stress, the entire unit is powder-coated in two layers: first with a zinc primer, then with a durable powder coating.   Installation is easy using the existing mounting points. No welding or modifications to the vehicle structure are necessary. However, plastic covers on the underside of the vehicle may need to be removed or trimmed. The complete installation kit, including brackets and the necessary screws, is included in the package.   This makes these HD Side Steps a worthwhile upgrade for anyone who not only wants their New Defender L663 to look more rugged but is also looking for real protection and added practicality for travel, everyday use, and off-road driving.   Benefits at a Glance Compatible with the Land Rover New Defender L663 from MY2020 onward  Rugged HD side steps with rock slider function  Can also be used as rock sliders and side sill protectors  Protects the side sills and body panels  A practical addition for off-roading, travel, and expeditions  Convenient step aid for everyday use  Makes it easier to access roof racks, roof tents, roof boxes, or awnings  Made from sturdy structural steel  Laser-cut and CNC-bent  Two-layer coating with zinc primer and powder coat  Resistant to corrosion, weather, and mechanical stress  Easy installation using existing mounting points  No welding or modifications to the vehicle structure required  Robust, functional off-road look    What's Included 1 set of HD side steps / rock sliders, left and right  Complete installation kit, including brackets and necessary screws 

NOLDEN 7" Bi-LED main headlight kit with two headlamps with low-/high-beam and adaptor for Mercedes G. Available in different colours. Innovative 7" LED main headlight with proven reflector technology combines low- and hight-beam as well as position light in one lamp. Original dimensions and standard H4 socket mean that this is an easy to fit, durable replacement upgrade for any Mercedes G Wagon. Also fits (in some cases with additional apaptors or wiring looms) other vehicles, like Land Rover Defender, various Toyota, Jeep Wrangler JK/TJ/CJ, etc. The integrated electronic driver / control unit makes for easy fitment. NOLDEN headlights are road legal, of course. They have ECE (also known as E-marked) and SAE approval and are available for either LHD (EU version) or RHD (UK version) vehicles. You can choose between light-crome and darker dark-crome looks. Compared to traditional halogen headlights LED lights offer many advantages: higher light output ("more light") more comfortable light ("white light"), closer to sunlight low energy consumption (32/39 W compared to 55/60 W low/high-beam) vibration and shock proof design (especially important for diesel cars or off-road use) never again (ca. 30.000 hrs lifetime) white road Illumination compatible with HID/Xenon one of the brightest LED high and low beam 7“ headlights available Many users of classical vehicles, especially off-road vehicles (Defender, Wrangler, G-Wagon) have been looking for modern headlights with classical looks. Up to now 7“ LED headlights had offered better illumination than halogen headlights, yet they didn't give optimum illumination or were of inferior design. In addition these were often retrofitting solutions that didn't meet OEM specifications. The new NCC 7“ Bi-LED headlight was especially tailored to meet the OEM requirements. All components, from the LED to the plug, are designed and produced accordingly making up a perfect overall system. The design of the 7“ Bi-LED headlights reminds more of a conventional halogen headlight that looks like the well-known classic design. The familiar appearance of the vehicle is thus not changed much and essentially still looks like “OE“. The illumination level of the new NCC 7“ Bi-LED headlight is equally good as that of a Xenon headlight. However, the new NOLDEN headlight system has the big advantage of a lower current consumption, which increases the life of the system significantly thus noticeably lowering the operating costs. In a normal case it can be expected that the life of the NCC 7“ Bi-LED headlight is much longer than that of the vehicle. The ligths don't require headlight adjustment or the headlight cleaning system of the Xenon system, retrofitting with the new NCC 7“ Bi-LED headlight is therefore much easier, faster and in the end less expensive than is the case with the Xenon headlights. Technical details: dimensions in mm: 177 x 152 number of LED: 5 x Osram Automotive output (low-/high-beam): 32 W / 39 W voltage range: 9-32 V lumens calculated: 1,880 lm / 2,400 lm lumens measured: 1,550 lm / 1,700 lm fixing: PAR56 homologation: ECE, SAE front lens: UV resistent polycarbonate hard coated front lens housing: lightweight, rigid alumium housing waterproof: 480 h salt spray tested and fully water proof to IP6K9K NOLDEN Bi-LED main headlights are also suitable and approved for many European, Asian and American motorbikes. The Nolden LED lights are available in chrome, dark-chrome and matt black and also for RHD vehicles. Please choose the desired version. You get one complete set for your vehicle. IMPORTANT: We do not ship the right-hand drive / left-hand traffic versions to UK.UK customers please visit www.4x4overlander.com for the RHD/LHT headlights.

Set of 4 AEZ Panama aluminium rims for the Land Rover New Defender The AEZ Panama combines a striking cross-spoke design with impressive stability, making it the ideal choice for demanding off-road adventures as well as for a stylish appearance on the road. With a load capacity of up to 1,025 kg, this rim is perfectly designed to meet the high demands of modern SUVs – especially the Land Rover New Defender.   Technical details: Size: 8.5x20" Offset (ET): 38 mm Colours: silver or black Bolt circle: 5x120 Load capacity: up to 1,025 kg   The AEZ Panama impresses with its high-quality workmanship, maximum robustness and a design that perfectly underlines the powerful character of the New Defender.   Ideal for anyone who wants to give their vehicle a high-quality, elegant and at the same time durable upgrade.

Great conversion kit for the 2nd row of seats With the introduction of Td4 Puma models from MY2007 onwards, Defenders featured not only a new engine and drive train but also significant changes to the interior. Due to new safety regulations, second row seats and their mounting points required a new layout. Consequently, more recent Td4 back seats will not fit when restoring or converting older pre-2007 models.  Our conversion kit enables you to install post-2007 second row seats in pre-2007 110 Defender Station Wagons. The back seat mounting kit contains a mid-crossmember, two second row seat supports, chassis bracket fixing kits and two adapted front panels for the rear wheel arches. All parts are galvanized.

Doors for Land Rover Defender Suitable for Defender TD4 2007 onwards The doors are primed. Available for front, back, left and right - Please choos the desired variant. Surface Treatment Notice This component is supplied exclusively with a primer coating. This primer is intended solely for temporary corrosion protection during storage and transport and is not suitable as a permanent surface finish for exterior automotive use. It is essential to sand the component, apply a suitable primer, and then either paint or powder-coat it in order to ensure rust resistance. Optionally, we recommend treating the inside of the component with a suitable corrosion protection grease. Only this will reliably prevent corrosion from forming again inside the component over the long term.  

Robust main headlamp with integrated low beam, high beam & position light - stainless steel mounting included NOLDEN 7" Bi-LED main headlight kit with two headlamps with low-/high-beam and position light, including stainless steels bezels. Price advantage! Innovative 7" LED main headlight with proven reflector technology combines low- and hight-beam as well as position light in one lamp. Original dimensions and standard H4 socket mean that this is an easy to fit, durable replacement upgrade for any Land Rover Defender 90/110/130. Price for one lamp! Also fits (in some cases with additional apaptors or wiring looms) other vehicles, like Jeep Wrangler JK/TJ/CJ, various Toyota, Mercedes G etc. The integrated electronic driver / control unit makes for easy fitment. NOLDEN headlights are road legal, of course. They have ECE (also known as E-marked) and SAE approval and are available for either LHD (EU version) or RHD (UK version) vehicles. You can choose between light-crome and darker dark-crome looks. Compared to traditional halogen headlights LED lights offer many advantages: higher light output ("more light") more comfortable light ("white light"), closer to sunlight low energy consumption (32/39 W compared to 55/60 W low/high-beam) vibration and shock proof design (especially important for diesel cars or off-road use) never again (ca. 30.000 hrs lifetime) white road Illumination compatible with HID/Xenon one of the brightest LED high and low beam 7“ headlights available Many users of classical vehicles, especially off-road vehicles (Defender, Wrangler, G-Wagon) have been looking for modern headlights with classical looks. Up to now 7“ LED headlights had offered better illumination than halogen headlights, yet they didn't give optimum illumination or were of inferior design. In addition these were often retrofitting solutions that didn't meet OEM specifications. The new NCC 7“ Bi-LED headlight was especially tailored to meet the OEM requirements. All components, from the LED to the plug, are designed and produced accordingly making up a perfect overall system. The design of the 7“ Bi-LED headlights reminds more of a conventional halogen headlight that looks like the well-known classic design. The familiar appearance of the vehicle is thus not changed much and essentially still looks like “OE“. The illumination level of the new NCC 7“ Bi-LED headlight is equally good as that of a Xenon headlight. However, the new NOLDEN headlight system has the big advantage of a lower current consumption, which increases the life of the system significantly thus noticeably lowering the operating costs. In a normal case it can be expected that the life of the NCC 7“ Bi-LED headlight is much longer than that of the vehicle. The ligths don't require headlight adjustment or the headlight cleaning system of the Xenon system, retrofitting with the new NCC 7“ Bi-LED headlight is therefore much easier, faster and in the end less expensive than is the case with the Xenon headlights.  Technical details: dimensions in mm: 177 x 152 number of LED: 5 x Osram Automotive output (low-/high-beam): 32 W / 39 W voltage range: 9-32 V lumens calculated: 1.880 lm / 2.400 lm lumens measured: 1.550 lm / 1.700 lm fixing: PAR56 homologation: ECE, SAE front lens: UV resistent polycarbonate hard coated front lens housing: lightweight, rigid alumium housing waterproof: 480 h salt spray tested and fully water proof to IP6K9K NOLDEN Bi-LED main headlights are also suitable and approved for many European, Asian and American motorbikes. Also note our lower-price vehicle-dependent bundles for Jeep Wrangler JK, Mercedes G and Toyota LandCruiser HZJ. Please note that these lights have position lights. You can use the standard Defender position lights along with the headlight position lights, or you disconnect the position light of the NOLDEN lamps. You receive a complete fitting kit, including two lamps and fitting material for your vehicle. The Nolden LED lights are available in chrome, dark-chrome and matt black, the stainless steel bezels either in "stainless" or black powder coating. These lights are also available for RHD verhicles. Please choose the desired version. IMPORTANT: We do not ship the right-hand drive / left-hand traffic versions to UK.UK customers please visit www.4x4overlander.com for the RHD/LHT headlights.

This full stainless steel spare wheel carrier for Defender SW/HT is the successor to our Defender spare wheel carrier RRHNAHI sold by the hundreds. It is available in two colours. The Defender rear door suffers from the heavy weight of the large spare wheel. Depending on use, after about five years or 50.000 kms the first cracks in the rear door frame appear. There are two solutions for this well-known problem: either move the spare wheel to the bonnet (see our bonnet spare wheel mount for that, not possible for post MY 2007 Defenders) or you fit our rear door spare wheel carrier. It takes off the complete weight from the rear door and opens along with the door. The carrier is fitted to the rear crossmember, a plate is mounted to the existing holes in the door, which is then attached to the carrier with two cranked stainless steel pivots. This carrier has been tested extensively, among others on the "Grand Erg" rallye and combines easy fitting with high toughness and exeptional usability. Available for all Defender models with rear door (Station and Hardtop). Improved design in 2014 and full stainless steel fabrication. The bearing is maintenance free, the complete carrier rustproof and can be completely revised it necessary. It's compatible with Land Rover rear step / bumper with towbar. Fitting is possible on a DIY basis. We also offer fitting service. If you also 'buy' the fitting charge we will contact you for an appointment. The spare wheel carrier opens together with the rear door, no further unlocking necessary. For vehicles with a tailgate (Pickup, not HCPU) we offer a separate sparewheel carrier: NARRTDEF-STPU The carrier is fully made out of stainless steel and black powder coated. The spare wheel carrier is designed and tested for a total weight (spare wheel and possibly other accessories) of 120 kg.

Lowering spring kit TREKFINDER for INEOS Grenadier - approx. 30 millimetres the lowering is approx. 30 millimetres suitable for 6-cylinder diesel & petrol engines for vehicles WITHOUT winch the standard shock absorbers can still be used Trailer operation is permitted Suitable for the following versions: Vehicle manufacturer: Ineos Automotive ( UK ) Commercial designation / version: INEOS GRENADIER Permissible axle loads ( v / h ) in kg: 1667 / 2150 Vehicle type / make: GM with EG-TG-No.: e9*2018/858*11384*... Vehicle type / make: GN with EG-TG-No.: e9*2018/858*11385*... Scope of delivery: 4 pieces TREKFINDER coil springs ( HA progressive and VA linear ) 1 piece TÜV® parts certificate

ExRoof cargo bed support - suitable for roll cover systems With the ExRoof platform for the cargo bed, you can create additional storage space in your pickup and get the most out of your cargo bed. The cargo bed support has been specially developed for cargo beds with roller blinds. The feet are mounted on the C-rail. All accessories can be easily attached to the ExRoof cross profiles using slot nuts, such as awning brackets, eyebolts for lashing straps, quick-release roof tent fasteners, brackets for sand sheets and much more. The carrier offers sufficient space for a roof tent or transport boxes. The total height is 29 cm. The maximum permitted load depends on the permitted load capacity of the roll cover. With the Mountain Top, for example, a maximum of 75 kg is permitted.   Technical data: Platform dimensions (L x W x H): 1400 x 1350 x 49 mm Total height (feet + platform): 290 mm Platform material: aluminium (powder-coated) Feet material: steel (S235 JR, powder-coated) Colour: black Total weight: 24 kg Compatibility: Horizontal T-slots required on both sides of the cargo bed Distance between the T-slots: minimum 1000 mm, maximum 1360 mm Check insertion of the T-bolts supplied (see technical drawing) Note risk of collision with any existing cabin-side styling bars Scope of delivery: 1 x ExRoof platform 4 x mounting feet for cargo bed (on C-rail) Mounting material Installation instructions

Steering Box Defender / Discovery I / Range Rover Classic LHD This high-quality steering box is the right solution for left-hand-drive (LHD) Land Rover Defender, Discovery I, and Range Rover Classic models. It is a brand-new part supplied with no exchange requirement, making it ideal for a reliable and long-lasting steering system repair. This steering box is also a significantly more affordable alternative to the original manufacturer part from ADWEST, part number QAF500120. When precision, safety, and clean steering response matter, this steering box is the right choice. Especially on older Land Rover models, a worn or leaking steering box is often the cause of excessive play in the steering, imprecise handling, or increased steering effort. With this new steering box, you can restore your vehicle’s steering system to a dependable standard. Your benefits at a glance: High-quality steering box Suitable for Defender, Discovery I, and Range Rover Classic Version for left-hand-drive vehicles (LHD) Brand-new part No old part return required Ideal solution for a professional steering system repair  

Cable winch set for Lada Niva / Taiga, including complete installation set The extremely robust bumper fits the original stops on the Lada.Now you have not only a winch holder, but a massive, shapely steel bumper, which was kept in the original design. The powder-coated bumper has a shackle holder (shackle included) and pickup points for a Farm Jack jack. WITH TÜV AND PARTIAL APPROVAL FOR GERMANY! The certificate applies to vehicles up to the year of construction: see table below! ***Important!****Since the original alternator and the Lada battery are very small, we recommend one Upgrade at least the battery. Ask your Lada dealer about the possibilities. NOT SUITABLE FOR A LADA BRONTO with plastic bumper!In the version with aluminum bumper, the system fits! The grille must be cut out for new Ladas! Technical specifications: Engine:Motor power: 2,3 HPMotor type: permanent magnet (magnetic field is generated by means of a permanent magnet)Maximum power consumption: 180 ampsVoltage: 12 volts Transmission:3-stage planetary gearReduction: 166: 1 General data:Max pulling force: 2.300 kgMaximum train speed: 4 m / min (measured without load)Plastic rope (diameter x length): 6 mm x 25 mDrum (diameter x length): 63x139 mmOverall size (LxWxH): 465x158x215 mmWeight winch 29 kgWeight installation set 21 kgOverrunning clutch (decoupling the gearbox to unwind the rope by hand) Included accessories:- Cable remote control- rope window- fixing screws- Operation manual- hook TÜV for the following vehicle types: Vehicle type      ABE / EG-BE no.       Variant / version212140               e2 * 93/81 * 0183 * ..             all212140               e2 * 98/14 * 0051 * ..             all21214                 e1 * KS * 0004 * ..                 all2121A                 e1 * KS * 0008 * ..                 all2121                   e2 * 98/14 * 0183 * ..             all2121                   e2 * 2001/116 * 0260 * ..       all2121 **** DA       e2 * 2001/116 * 0326 * ..       all2121DE              e1 * KS07 / 46 * 0021 * ..      allM2121               e2 * KS07 / 46 * 0011 * ..       allN2121               e2 * KS07 / 46 * 0012 * ..       allMU2121                 e2*KS07/46*0056*            allMU2131                  e2*KS07/46*0076*           allM2131               e2 * KS07 / 46 * 0077 * ..      all

Fan manifold Land Rover Td5 incl. high-strength manifold bolt M8 and gaskets For all Land Rover Defender / Discovery Td5 Engineered for high performance or modified vehicles. This prevents bent manifolds or broken bolts. The package includes heavy duty bolts and seals. This is motorsport equipment and NOT street legal !

The XPL Curved Lightbar is an extremely powerful installation solution for the slot of the standard radiator grille Installing work lamps, additional headlights or light bars on your vehicle is not too difficult – when you’re talking older pickups or classic Defenders, that is. Obviously, with newer cars like the New Defender one should be a lot more cautious before drilling holes or attaching brackets to the expensive exterior. Vision X Lighting specialize in custom solutions, combining top performance, sleek design and installation methods that minimize effort and actual alterations to your car.  The XPL Curved Lightbar by Vision X is an elegant and powerful LED solution for the lower opening in the standard grille of the New Defender. The array of individual 5 W CREE LEDs delivers a light beam of over 600 m – providing safety in all weather conditions, off-road or on-road, for work or sports. The XPL Curved lightbar also features backlighting that can be used as daytime running lights.  The installation is fairly simple and requires roughly 4 hrs. Both the grille’s plastic substructure and the lower opening need to be modified by sawing out specific areas. Detailed instructions, fastening materials and electric connections are included in the delivery. Mounting behind the radiator grille is also possible.  Specifications for XPL Curved Lightbar: LEDs: 5W per LED Housing material: aluminium Light colour temperature: 6000 Kelvin Voltage: 9-32V DC Current: 3.12A~8.96A@24V DC - 6.25A~17.92A@12V DC Vibration resistance: 21 Grms Lens material: Polycarbonate Smooth backlight Proprietary IRIS reflector technology Curved high power light bars Weatherproof Deutsch connector with plug-and-play wiring harness Certifications: CE, RoHS, IEC 62471, ECE R112 Thanks to our iris reflector technology and the unique curve of the bar, the XPL Curved series produces a wide spot beam pattern with a range of over 600 metres. Scope of delivery: Complete radiator grille set for New Defender with XPL-HC23 light bar, brackets and wiring harness including detailed installation instructions.

The areas around the doors are corrosion hotbeds in a Defender. Even though this is a well-known fact, the rust remains very often undetected and keeps eating into structural components and body panels. The doors feature many corners, angles and surfaces that constantly trap water and wet dirt. Screw fittings, rivets, welding points, the combination of different materials like steel, aluminum and rubber as well as mechanical stress often exacerbate the problem. If you are facing large scale restoration work in your 4/5 door Defender, you might consider whether a complete replacement of B and C pillars as well as the door sill isn’t the cheaper, quicker and most of all more thorough solution. We are offering entire sets for the right or left side of all models where door seals are only pushed in and not riveted. If you have riveted seals, they need to be adapted. If you need to replace only the C posts you can find them here.

Ideal carrier system for off-road use and for tradesmen Off-road use with the Ford Ranger requires particularly stable mounts, as the vehicle is exposed to higher forces. We have built the platform for the Ford Ranger / Raptor with this in mind. You have sufficient space and fastening options for attaching load securing devices or bolting on practical roof rack accessories. Heavy loads on the roof of the Ford Ranger can therefore be positioned anywhere on the roof rack platform and securely lashed down. Both across the roof and in the direction of travel. Roof rack uses the original attachment points, no drilling required Compatible with Ford Ranger (XL, XLT and Tremor from 2023), Ford Ranger Raptor (from 2023) and VW Amarok (Entry, Style and Life from 2023) Aerodynamic deflector is included in the scope of delivery ExRoof roof rack for Ford Ranger & Raptor (from model year 2023) The innovative horntools ExRoof roof rack is your perfect everyday companion! Thanks to its all-round profile rail, any add-on parts can be attached using sliding blocks. The ExRoof roof rack for the Ford Ranger / Raptor is made of powder-coated aluminum and therefore weighs just 33 kg. With a size of 1400 x 1280 mm, you have enough space on the ExRoof platform to mount a roof tent, transport boxes, tools and other accessories on the roof of your vehicle.   This Ford Ranger roof rack is also very popular with tradesmen. If the loading area of the pick-up is no longer sufficient for tools or other transport items, toolboxes or ladders can be safely stowed on the platform.   Technical data: Dimensions: 1400 x 1280 mm (platform) Weight: 33 kg (roof rack + roof rack platform) Surface: RAL 9005 powder-coated Scope of delivery: Roof rack feet Roof rack platform Wind deflector Fastening material and installation instructions

ExRoof roof rack for Isuzu D-Max 2021 Double Cab (from year of construction 2021)   The horntools ExRoof roof rack is your perfect everyday companion! Thanks to its all-round profile rail, add-on parts can be attached using sliding blocks. The ExRoof is made of powder-coated aluminum and therefore weighs only 20kg. With a size of 1600mm x 1250mm x 49 mm, you have enough space to store your accessories.   Technical data: Material: Aluminum 6063 Weight: 20 kg Surface: Powder coating Size: 1600mm x 1250mm x 49 mm Scope of delivery Base carrier Roof rack feet Fastening material and installation instructions Caution: Static load capacity: 300 kg Dynamic load capacity: 100 kg The dynamic load capacity is not the manufacturer's approval. The manufacturer's load capacity must not be exceeded. The static load indicates the load capacity when stationary. The dynamic load capacity refers exclusively to paved roads. The load must be evenly distributed over the entire surface.