Current %

Your tyre for extreme conditions: BFGoodrich KM3 Offroad Goodrich Mud Terrain T/A KM3 255/85R16 119QThe off-road tire BFGoodrich Mud Terrain T / A KM3 is primarily intended for off-road use, it is less suitable for driving on paved roads. The tires of this type are characterized by a special tread, which is responsible for safety when driving off-road, as well as a reinforced construction. The MT tires are the best way out for drivers who need tires for mud and water when driving off-road and are not afraid of rocky slopes. The very deep grooves of the tread and the massive blocks make driving on these tires safe. Due to the wide gaps, the tire cleans itself up quickly, which makes driving easier on sand, for example. This typical terrain model is also reinforced so that drivers do not have to worry about the tire being destroyed when driving in difficult terrain. Available in:255/85 R16235/85 R16 click here LR WOLF Steel Wheel 6.5x16"- corresponds to part number ANR4583 PM- dimensions 6,5 x16", offset 20,6 If the wheels need to be rebalanced at a later date, we recommend balancing the rims for the Land Rover Defender using bolt or bolt circle centring.

Complete wheel set BF Goodrich 265/65R18 117R All Terrain T/A KO2 on Borbet CW7 alloy wheels BFGoodrich ALL Terrain T/A KO2 265/65 R18 117R: The BFGoodrich All Terrain T/A KO2 265/65 R18 117R guarantees driving fun even off the paved roads. It is very stable and has good road grip. It also handles not too difficult terrain with some mud, loose ground well. For extreme terrain and little road use, however, a MUS tyre is recommended. In the AT range BFGoodrich is a very good choice. A SPECIAL TYRE MIXTURE that is resistant to cuts and chipping on the sidewalls to withstand sharp stones. Designed to resist chipping and cracking caused by sharp stones and obstacles in the terrain. IMPRINTED CLAMPS on the sides for more grip and better sidewall protection. The large crampons on the sidewall are synonymous with bite, especially when the tyre is rolling at low pressure. Greater thickness of rubber on the sidewall protects the tyre from off-road hazards. STRENGTHENED CABLES for less sensitive sidewalls. Flank weakness can spoil off-road activities very quickly. Oversized sidewall cables give the carcass the protection it needs for tough off-road use. Performance 50% off-road - 50% on-road Tyre width 265 Ratio of sidewall height to tyre width in percent 65 Rim diameter: 18" Load index: 117/114 Speed index: R 3PMSF Alpine symbol (so-called snowflake): yes M+S marking: yes Weight: 23,06 per tyre Tyre type: All-season Tyre type: Radial Noise emission: 74db Noise class (from 1-quiet to 3-noise): 2 Wet grip (grip on rain-soaked road): B Fuel efficiency (A to G): F When ordering, please let us know whether the white lettering is to be fitted inside or outside.BORBET CW7 alloy wheels 18 inch:With the BORBET CW7 in the "Commercial Wheels" category, a new wheel is now presented that is not only convincing in terms of design, but also with high wheel loads of up to 1,400 kg.The CW7 stands for a new, striking look that is not only defined by the number of spokes, but is also made for the real movers and shakers among vehicles. From vans to off-roaders to motorhomes. Manufacturer: Borbet Brand: CW7 Size/offset: 7.5x18", offset 47 Colour: either matt black or matt bronze Suitability: for Ineos Grenadier Certification: for 255/65R18 255/70R18 265/65R18 A01) K02) Included in delivery: Rim, incl. matching wheel nuts High wheel load Winterproof Scope of delivery: Rim, incl. matching wheel nuts / Note: the wheel nuts of the original Ineos alloy rims also fit on these rims!The price refers to 4 or 5 complete wheels incl. mounting and balancing. This article is bulky goods.

BF Goodrich All Terrain T/A KO3 all-season tyre on Wolf steel rim Tyre size: 235/85R16 Rim size/offset: 6.5x16" T20.6   BFGoodrich® All-Terrain T/A KO3 - One tyre for all occasions.   Wherever the journey takes you: the BFGoodrich® All-Terrain T/A KO3 is ready for action. This 3PMSF-certified tyre offers strong grip on mud and snow. With its serrated tyre shoulder design and mud phobic bars, it also contributes to controlled handling on and off the road. Brand: BFGOODRICH Tread pattern: ALL-TERRAIN T/A KO3  Dimension: LT235/85R Diameter: 16" Load index: 120 Speed index: S Fuel efficiency class: E Wet grip class: C External rolling noise classification: B External rolling noise: 74 dB Snowflake symbol: yes   Resistance on a new level.  BFGoodrich® all-season off-road tyres for SUVs, off-road vehicles and light trucks Designed for high grip and controlled handling on and off-road CoreGard technology and improved rubber compound for increased resistance and durability Optimised tread design for even wear and longer service life Off-road design for increased off-road performance All-season tyre When ordering, please let us know whether the white lettering should be mounted on the inside or outside.   We recommend to balance the rims for the Land Rover Defender bolt or bolt circle centred.   The rims used are LR WOLF rims (black) 6.5x16 inch, offset 20.6, which correspond to part number ANR4583 PMGEN. These are the ORIGINAL rims from Land Rover (not a replica!). These black rims can also be ordered powder-coated in the colour white or black.   Note: We always recommend the powder-coated rims, as the rims with a primer are still susceptible to corrosion due to the open pores alone. If the primed rims corrode, there is therefore no right of return.    Please note: Wheel nuts for aluminium rims cannot be used on steel rims.   Balancing Defender wheels on conventional centre-centring balancing machines often leads to errors. For this reason, we use a so-called stud centring system, in which the wheel is balanced using a special adapter plate.    

BF Goodrich All Terrain T/A KO3 all-season tyre on CLASSIC steel rim Tyre size: 265/75R16 Rim size/offset: 8x16" offset 0   BFGoodrich® All-Terrain T/A KO3 - One tyre for all occasions.   Wherever the journey takes you: the BFGoodrich® All-Terrain T/A KO3 is ready for action. This 3PMSF-certified tyre offers strong grip on mud and snow. With its serrated tyre shoulder design and mud-repellent Mud Phobic Bars, it also contributes to controlled handling on and off the road. Brand: BFGOODRICH Tread pattern: ALL-TERRAIN T/A KO3  Dimension: LT265/75R Diameter: 16 inch Load index: 119 Speed index: S Fuel efficiency class: E Wet grip class: C External rolling noise classification: B External rolling noise: 74 dB Snowflake symbol: yes   Resistance on a new level.    BFGoodrich® all-season tyre for off-road driving with SUVs, off-road vehicles and light trucks Designed for high grip and controlled handling on and off-road CoreGard technology and improved rubber compound for increased resistance and durability Optimised tread design for even wear and longer service life Off-road design for increased off-road performance All-season tyre When ordering, please let us know whether the white lettering should be mounted on the inside or outside.   If the wheels need to be rebalanced at a later date, we recommend balancing the rims for the Land Rover Defender using bolt or bolt circle centring.   The tyres are fitted with the popular ANR Classics rims 16 inch. These are optionally available in primed black, powder-coated black and powder-coated white. The ANR Classics were designed with the Landrover history in the background, manufactured exclusively for Nakatanenga and really round off every Defender perfectly. The price refers to 4 or 5 complete wheels incl. mounting / balancing.   This article is bulky goods      

Mobile parking heater with aluminum box, various versions Make way, here comes the second generation of our mobile parking heaters in a box! We have packed even more technology, even more experience and even more customer feedback into our new mobile heating boxes. If you are looking for a small, self-sufficient and portable heat source with unrivaled capacity for cold days and nights in unheated outdoor shelters or temporary accommodation, you get everything you need (or want) in a small, weatherproof aluminum box. Available in three modular versions with different configurations, the Nakatanenga heating box provides the perfect, independent heat source for tents, gazebos, garden sheds, mountain huts, snack stands, stalls and much more. The heart of the mobile parking heater is the Autoterm Luft 2D, a diesel-powered air heater with a maximum heat output of 1.8 kW and a diesel consumption of just under a quarter of a liter per hour at full power. With a tank capacity of 18 liters in the twin-tank version, this means that it can heat at full throttle for over 70 hours. The economical unit, which is also very quiet at 55 dB thanks to the exhaust silencer, is controlled by a digital control unit with timer in the version with two batteries and can also be switched on and off by radio remote control. This allows you to preheat your camper, roof tent, caravan or hunting lodge in good time for getting up or for the evening, for example, and operate it from the place where you are staying or sleeping inside*. In contrast to the previous models, the five versions of our mobile parking heater are now only available in one box size, namely 42 liters. This is significantly more compact than the old version in the large version and only slightly more voluminous than the small model from before. What is the advantage? The new universal crate has a modular interior with a powerful performance. Depending on whether you need tanks, batteries or both in the box, you can choose the appropriate version when purchasing: with 9.2 L single or 18.4 L double tank, each without battery, as well as with single tank, two batteries and digital control. However, it can also be easily retrofitted or converted if requirements change. This is made possible by elaborately designed brackets in the box and the use of specially manufactured, made-to-measure tanks.   Features of heating box 1 and 2 (without battery) - Heating unit 1 with 1 x 9.2-litre diesel tank - Heating unit 2 with 2 x 9.2 = 18.4-litre diesel tank - USB interface for charging smartphone, power bank, tablet, etc.- Capacity display- PU5 control panel (without timer and storage options)- 12 V connection socket for supplied pole terminal cable- Alternatively, a cable for cigarette lighter (KMSH cable) can be used- 2 radio remote controls- Connection option for external temperature sensor (the connection is inside the box, not outside)”     Features of heater box 3 (with 2 AGM batteries) - 2 x 33 Ah 12-volt AGM batteries, leak-proof and maintenance-free - 9.2-litre diesel tank - USB interface for charging smartphone, power bank, tablet, etc.- Capacity display- Comfort Control control panel (with timer and memory option)- SAE connection socket (suitable for Optimate chargers or Optimate solar charger)- 2 radio remote controls- Connection option for external temperature sensor (the connection is inside the box, not outside)     Features of heating box 4 (with 1 LiFePo battery) - 1x 35 Ah 12-volt LiFePO4 lithium service battery, suitable for long-term storage and extremely temperature-stable  - 9.2-litre diesel tank - USB interface for charging smartphone, power bank, tablet etc.- Capacity display- Comfort Control control panel (with timer and memory option)- SAE connection socket (suitable for Optimate chargers or Optimate solar charger)- 2 radio remote controls- Connection option for external temperature sensor (the connection is inside the box, not outside)-> Please only use LiFePo-compatible chargers   Features of heating box 5 (with 2 LiFePo batteries) - 2x 35 Ah 12-volt LiFePO4 lithium service batteries, suitable for long-term storage and extremely temperature-stable - 9.2-litre diesel tank - USB interface for charging smartphone, power bank, tablet, etc.- Capacity display- Comfort Control control panel (with timer and memory option)- SAE connection socket (suitable for Optimate chargers or Optimate solar charger)- 2 radio remote controls- Connection option for external temperature sensor (the connection is inside the box, not outside)”-> please only use LiFePo-compatible chargers       The warm air is transported via a firmly screw-fastened, waterproof Flexi hose. As the warm air hose is different for every user and every requirement, we do not include a standard length, but leave it up to you to order the desired length separately here in the store, with or without a silicone sleeve. You can find the perfect storage bag for the Flexi hose here in the store. Regardless of the configuration, the mobile parking heaters are always easy to transport and make the difference between experiencing and suffering in the cold seasons. Whether it's an aurora safari, selling cookies at the Christmas market or winter camping in a roof tent, nothing is really fun if you freeze to death. *ATTENTION: As a precaution, we would like to point out that operation in closed rooms is not permitted due to the risk of poisoning from exhaust fumes. In addition, for optimum heating performance, make sure that the air inlets for combustion and hot air are positioned so that they are protected from the weather. Dimensions Internal dimensions 550x350x220 mm External dimensions 580x380x240 mm   Unladen weight: Heating unit 1, without battery and with 1 tank: 16 kg Heating unit 2, without battery and with 2 tanks: 18 kg Heating unit 3, with 2 AGM batteries and 1 tank: 45 kg Heating unit 4, with 1 LiFePo battery and 1 tank: 19 kg Heating box 5, with 2 LiFePo batteries and 1 tank: 24 kg Depending on how many starts are made, the battery lasts at least 40 h, but more likely between 60 and 70 h.  LiFePo4 batteries - i.e. batteries with a lithium iron phosphate cathode - are the ideal supply batteries for camping or electrical work on the move. In contrast to conventional lead-acid AGM technology, lithium batteries combine superior charging properties with much lower weight and volume and a long service life. LiFePo4 batteries can be deep-discharged without any problems, which sooner or later leads to irreparable damage with AGM batteries, as the rule of thumb here is that you should never draw more than 50% charge. If you are not dependent on the greater cold tolerance of AGM batteries, you should definitely consider the higher costs for LiFePo4 batteries and compatible charging technology. The weight and space savings, the long service life and the uncomplicated discharging and charging of the battery are strong arguments in favor of the investment. What's more, LiFePo4 technology is also extremely safe And a special note on aluminum: Although we take the utmost care during storage and shipping, as with all our products, aluminum boxes can always show minimal scratches, stains, dents or other surface features upon delivery. These are material-related and result from the specific properties of the light metal.  In contact with oxygen, aluminum forms a natural, corrosion-protecting patina and is also relatively soft compared to steel, which is three times heavier. This makes the material ideal for use in sheet metal, especially when weight and resistance are important. On the other hand, however, it also means that aluminum can never be completely free of patina or other marks, even on delivery: Small scratches, stains etc. therefore do not constitute grounds for complaint. Ultimately, aluminum boxes are intended to be robust objects of daily use. Like everything that is actively used, they develop an individual patina and every trace of use tells a story. So, have fun with it! If you want to heat the interior of your vehicle, we offer an installation service for warm air ducting through a ventilation plate.   Please note the variants without batteries:  Most portable power stations or battery boxes (such as Goal Zero, Eco Flow, Bluetti etc.) are unfortunately not suitable for operating mobile parking heaters. The heater requires up to 15A as starting current and when shutting down, but very few battery boxes can provide this. Suitable battery boxes for operating the mobile parking heater Please note the legal information on batteries HERE. For certain types of batteries, we are legally obliged to charge a deposit.   EQUIPMENT HIRE:  Hire an AUTOTERM 2D12 mobile diesel/air heater in an aluminium case with battery If you only need a mobile space heater for a short period, you can easily hire one here:   Click here to make a no-obligation enquiry! Rental prices   1 week(7 days) 2 week(14 days) 3 week(21days) 4 week(30 days) AUTOTERM 2D12 in an aluminium case WITH battery 351€ 467€ 537€ 584€     Prices include VAT PLEASE NOTE: As a precaution, we would like to point out that the appliance must not be used indoors due to the risk of poisoning from exhaust fumes. Furthermore, to ensure optimum heating performance, please ensure that the air intakes for combustion and hot air are positioned in a way that protects them from the weather. Our hire heaters (battery-powered) are supplied in wooden crates and delivered by a haulage contractor. The diesel tank is empty on delivery and MUST also be empty when returned!

Robust and powerful: BF Goodrich KO2 on Borbet CW7 – the perfect complete wheel set for your INEOS Grenadier BF Goodrich ALL Terrain T/A KO2 265/65 R18 117R:   The BFGoodrich All Terrain T/A KO2 265/65 R18 117R guarantees driving pleasure even off the beaten track. It is very stable and has good road grip. It also copes well in not too difficult terrain with some mud and loose ground. For extreme terrain and little road use, however, a MUS tire is recommended. In the AT area, BFGoodrich is a very good choice.   A SPECIAL TIRES compound that is resistant to cuts and chipping on the sidewalls to withstand sharp rocks. Designed to resist chipping and cracking that can be caused by sharp rocks and obstacles in the terrain. IMPRINTED CLAMPS on the sides for more grip and better sidewall protection. The large crampons on the sidewall are synonymous with bite, especially when the tire is rolling at low pressure. A greater thickness of rubber on the sidewall protects the tire from off-road hazards. REINFORCED CABLES for less sensitive sidewalls. A weak sidewall can spoil off-road activities very quickly. Oversized sidewall cables provide the carcass with the necessary protection for tough off-road use.   Performance 50% off-road - 50% road   Tire width 265 Ratio of sidewall height to tire width in percent 65 Rim diameter: 18" Load index: 117 Speed index: R 3PMSF Alpine symbol (so-called snowflake): yes M+S marking: yes Weight: 23.06 per tire Tire type: All-season Tire construction: Radial Noise emission: 74db Noise class (from 1-quiet to 3-noisy): 2 Wet grip (grip on wet roads): B Fuel efficiency (A to G): F The tyres are already mounted on the rims and have TPMS sensors installed. The white lettering is mounted on the outside!   BORBET CW7 18 inch alloy wheel   The BORBET CW7 in the “Commercial Wheels” category is a new wheel that not only impresses in terms of design, but also with high wheel loads of up to 1,400 kg. The CW7 stands for a new, striking look that is not just defined by the number of spokes, but is perfect for the real movers and shakers among vehicles. From vans to off-roaders and motorhomes.   Manufacturer: Borbet Brand: CW7 Size/offset: 7.5x18", ET 47 Color: matt black Suitability: for Ineos Grenadier Approval: for 255/65R18 255/70R18 265/65R18 A01) K02) Scope of delivery: rim, incl. matching wheel nuts High wheel load Winter-proof Scope of delivery: rim, incl. matching wheel nuts The price refers to 5 complete wheels incl. fitting and balancing. This article is bulky goods.      

BF Goodrich All Terrain T/A KO3 all-season tyre on Dotz steel rim for Defender up to MY2016 Tyre size: 265/75R16 Rim size/offset: 7x16" offset 8   BFGoodrich® All-Terrain T/A KO3 - One tyre for all occasions.   Wherever the journey takes you: the BFGoodrich® All-Terrain T/A KO3 is ready for action. This 3PMSF-certified tyre offers strong grip on mud and snow. With its serrated tyre shoulder design and mud phobic bars, it also contributes to controlled handling on and off the road.   Brand: BFGOODRICH Tread pattern: ALL-TERRAIN T/A KO3  Dimension: LT265/75R Diameter: 16" Load index: 119 Speed index: S Fuel efficiency class: E Wet grip class: C External rolling noise classification: B External rolling noise: 74 dB Snowflake symbol: yes  Resistance on a new level.    BFGoodrich® all-season off-road tyres for SUVs, off-road vehicles and light trucks Designed for high grip and controlled handling on and off-road CoreGard technology and improved rubber compound for increased resistance and durability Optimised tread design for even wear and longer service life Off-road design for increased off-road performance All-season tyre When ordering, please let us know whether the white lettering should be mounted on the inside or outside.   If the wheels need to be rebalanced at a later date, we recommend balancing the rims for the Land Rover Defender using bolt or bolt circle centring.   The rims used are DOTZ DAKAR steel rims in 7x16 inch format with approval for Land Rover Defender 90/110, Range Rover Classic and Discovery, which are available in silver, bronze or black.   Please note: Wheel nuts for aluminium rims cannot be used on steel rims.   The balancing of Defender wheels often leads to errors on conventional centre-centring balancing machines. For this reason, we rely on a so-called stud centring system, which uses a special adapter plate to balance the wheel as if it were mounted on a vehicle.   The price refers to 4 or 5 complete wheels incl. fitting / balancing.   This article is a bulky item.      

Wheel set Dotz Dakar Steel Rim and BFGoodrich All Terrain Tire  A bigger footprint with Dotz Dakar Steel Rims and BFGoodrich All Terrain tires not only suits Defenders, G-Wagons etc. but also the Jimny II GJ HJ, turning tiny Jimny into Big Jim. The fact that the Dotz Dakar has become a classic for all kinds of 4x4‘s is no accident. The steel rim with its timeless design and its high-quality manufacture is tough to beat when it comes to performance, be it a Sahara rally or a weekend trip. Dotz 4x4 designed this rim to be hardwearing and robust above everything else. Whenever the Dakar is released as a new vehicle, you can be sure it has undergone the most rigorous testing regime, giving you the highest quality and extreme durability. The Dotz Dakar is quickly cleaned by hand or pressure washer and due to its special finish it will be very easy on the eye for a long time – something that can’t be said of many steel rims. We are introducing the Dakar’s off-road performance and its classic look now also for the Jimny II GJ HJ and offer the rim with sizes  7x16 inches  with an offset of 0 mil.  A great rim needs an equally great tire and with the BFGoodrich All Terrain there’s no doubt that it’ll be up to the challenge. As a proven all-season multi-purpose tire, the latest T/A KO2 generation boasts even more improvements and better test results over its predecessor: the tire’s sidewalls are 20% more robust, durability doubles on gravel and adds another 15% on asphalt. Traction is also improved with an increase of 10% and 19% for slush/mud and snow, respectively. As far as the look is concerned the tire can be mounted with the white print to the in- or the outside. Certification documents are included. The wheel sets are available with or without spare wheel. The tire is suitable and permitted for winter use. Size:Rim 7 x 16" ET 0.0 Silver wie tire size 225/75R16*Rim 7 x 15" ET 0.0 Silver with tire size 215/65R16 * Required Modifications for 16” Wheel Set This wheel set size requires a suspension raising kit. The speedometer requires a ratio adapter. The wheel arch covers need to be adapted. Please let us know when ordering whether the white lettering is to be mounted inside or outside.

Mobile parking heater without battery and in aluminium box You can find information on hire equipment below. “It's a Thin Line Between Love and Hate” is the old song and this thin line between loving and hating the same thing is definitely the line on the thermometer in winter. If you freeze off the part of your body with an A, you're guaranteed not to enjoy even the fattest fish at the ice hole, the most magical aurora borealis or the greatest fun at the elephant meeting. That's why we have our solution for all outdoor activities in the cold seasons in the Alubox Pro: the AUTOTERM parking heater for on the go! With the exception of the battery, everything you, your family or your crew need for a warm and cozy outdoor feeling in your car, camper or roof tent is in the ultra-robust, waterproof 29L box. At its heart is the affordable and powerful AUTOTERM (Planar) 2D12 air heater, which can be powered from the vehicle battery via the cigarette lighter adapter. It is controlled via the PU5 control element. A 5.4 l fuel tank is already integrated in the box. This makes our mini heater ideal for on the road and mobile use on the vehicle or wherever a weatherproof cable connection to a car battery can be established. The warm air is transported into the room to be heated via a firmly screw-fastened, waterproof Flexi hose, which can be ordered separately in the desired length here in the store. ATTENTION: As a precaution, we would like to point out that operation in closed rooms is not permitted due to the risk of poisoning from exhaust fumes. Furthermore, for optimum heating performance, care should be taken to ensure that the air inlets for combustion and hot air are positioned so that they are protected from the weather. You can find the perfect storage bag for the Flexi hose here in the store.A larger standalone version of this parking heater with integrated battery is available here. You can also hire this parking heater from us.  Alu-Box Pro (29 liters) waterproof/dustproof according to IP54 standard AUTOTERM (Planar) 2D diesel / air heater ✔ Fuel tank (5.4 liters)✔ Hot air pipe connection, non-return valve, outlet and inlet feed-through✔ Including radio remote control✔ The openings for supply and exhaust air and for the power supply are splash-proof (can be closed with a screw cap or rubber plug)Dimensions of the aluminum box: WxHxD 390x340x290mmDimensions of the box with spigot: WxHxD 490x340x290Total weight: 11.2 kgTechnical data of the parking heater:- Fuel type: Diesel- Heating output: max. 1.8kW, min. 0.8kW- Volume of heated air: max. 75m³/h, min. 34m³/h- Fuel consumption during operation: max. 0.24l/h, min. 0.1 l/h- Power consumption during operation: max. 29W, min. 10W- Manual start/stop- Connection to a car battery or another external 12V battery PU-5 control element: - LED for ventilation display- LED for operating display- Temperature adjustable via rotary control The AUTOTERM Air 2D (Planar 2D) is equipped with an altitude kit! This means that the heater automatically reduces the injection volume according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content falls. The maximum heat output decreases in proportion to the amount of oxygen in the air. Roughly speaking, from 2000 meters upwards, the loss of output per 500m altitude is approx. 5%. Manufacturer tests up to 3440m were problem-free. No problems are to be expected up to 4000m. Up to 5000m the software calculates itself - but this could not yet be tested at real altitude. Please note: Most portable power stations or battery boxes (such as Goal Zero, Eco Flow, Bluetti etc.) are unfortunately not suitable for operating the mobile parking heaters.The heater requires up to 15A as starting current and when shutting down, but very few battery boxes can provide this..In general, however, direct connection to the battery terminals is the best solution   If you want to heat the interior of your vehicle, we offer an installation service for warm air ducting through a ventilation plate.   Please note the legal information on batteries HERE. For certain types of batteries, we are legally obliged to charge a deposit.   EQUIPMENT HIRE:  Hire an Small independent mobile heating system w/o battery Click here to make a no-obligation enquiry!    Rental rates   1 week(7 days) 2 week(14 days) 3 week(21 days) 4 week(30 days) AUTOTERM 2D12 in Alubox without Batterie  287€  382€  438€  478€  Prices include VAT PLEASE NOTE: As a precaution, we would like to point out that the appliance must not be used in enclosed spaces due to the risk of poisoning from exhaust fumes. Furthermore, to ensure optimum heating performance, please ensure that the air intakes for combustion and hot air are positioned in a way that protects them from the weather. Our hire heaters are delivered in wooden crates. The diesel tank is empty on delivery and MUST also be empty when returned!

Standard main beam headlights do the job as long as the road runs straight to the supermarket. Once the tarmac ends, everything left and right of the track goes dark fast. And from that point on, the terrain tends to keep surprises ready, for example a deer that doesn't see the off-roader coming, or a road edge that suddenly drops away into a deep ditch. The Vision X CG2 CPM710 Light Cannon make those surprises visible: multi-LED driving lights for the Ineos Grenadier, built for short and medium range. The beam of the Vision X auxiliary driving lights for the Grenadier Each lamp holds seven LEDs of 7 watts each, every one with its own 10° optic, and together they produce a wide driving beam. That works out to 49 watts per lamp, so 98 watts as a pair. Colour temperature sits at 6,000 Kelvin, which gives the light a clear, neutral-white character. Anyone looking for range rather than width should take a look at the single-LED sibling, the Vision X CG2 CPZ110. Clear or yellow lens? The Vision X auxiliary driving lights for the Grenadier come with either a clear or a selective yellow lens. Clear delivers the full light output and is the standard choice for clear nights. The yellow version is built for the days when something is hanging in the air, like dust on a desert track, mist in the mountains, driven snow on a pass, or heavy rain in the forest. Yellow light scatters less on particles in the air and therefore does not build the blinding wall in front of the bonnet that clear light can throw up when visibility drops. Housing waterproof and tough The housing of the CG2 CPM710 is a hybrid of aluminium and polycarbonate, tough enough for stone chips and light enough for the grille. The lens is acrylic, and together the lamps are IP68 waterproof and IP69K pressure-washer tested, stand up to 21.2 Grms of vibration, and operate between minus 40 and plus 80 degrees Celsius. The LEDs are rated for around 50,000 hours. Fitment in the grille, no drilling Vision X developed this kit specifically for the Ineos Grenadier and tested it on the vehicle in Europe. The lamps sit neatly in the grille with the supplied brackets, with no drilling or cutting required, so parking sensors and driver assistance systems stay fully functional. The plug-and-play wiring loom brings everything needed, including relay, fuses, and a CAN-bus connection, so the driving lights switch on automatically or manually together with the main beam. Anyone who wants to revert to the original setup can do so at any time. Technical specification Dimensions (L × W × H): 14.5 cm × 9.4 cm × 13.4 cm Manufacturer: Vision X LED type: 7 × 7 W LEDs, each with 10° optic (multi-LED) Power: 2 × 49 W (98 W as a pair) Luminous flux: 10,500 lumens total Range: approx. 215 m Beam type: wide driving beam Colour temperature: 6,000 K Lens: acrylic, clear or selective yellow Input voltage: 9 to 32 V DC Current draw: 4.08 A per lamp at 12 V (8.17 A as a pair), 2.04 A at 24 V Weight: 1.3 kg per lamp Housing: hybrid (aluminium and polycarbonate) Protection rating: IP68 waterproof, IP69K pressure-washer tested Vibration rating: 21.2 Grms Operating temperature: −40 °C to +80 °C Lifespan: around 50,000 hours Certifications: CE, RoHS, IEC 62471, ECE R112 (driving lamp) Connector: Deutsch connector In the box: 2 driving lights with connection cable

Set of 4 AEZ Panama aluminium rims for the Land Rover New Defender The AEZ Panama combines a striking cross-spoke design with impressive stability, making it the ideal choice for demanding off-road adventures as well as for a stylish appearance on the road. With a load capacity of up to 1,025 kg, this rim is perfectly designed to meet the high demands of modern SUVs – especially the Land Rover New Defender.   Technical details: Size: 8.5x20" Offset (ET): 38 mm Colours: silver or black Bolt circle: 5x120 Load capacity: up to 1,025 kg   The AEZ Panama impresses with its high-quality workmanship, maximum robustness and a design that perfectly underlines the powerful character of the New Defender.   Ideal for anyone who wants to give their vehicle a high-quality, elegant and at the same time durable upgrade.

The XPL Curved Lightbar is an extremely powerful installation solution for the slot of the standard radiator grille Installing work lamps, additional headlights or light bars on your vehicle is not too difficult – when you’re talking older pickups or classic Defenders, that is. Obviously, with newer cars like the New Defender one should be a lot more cautious before drilling holes or attaching brackets to the expensive exterior. Vision X Lighting specialize in custom solutions, combining top performance, sleek design and installation methods that minimize effort and actual alterations to your car.  The XPL Curved Lightbar by Vision X is an elegant and powerful LED solution for the lower opening in the standard grille of the New Defender. The array of individual 5 W CREE LEDs delivers a light beam of over 600 m – providing safety in all weather conditions, off-road or on-road, for work or sports. The XPL Curved lightbar also features backlighting that can be used as daytime running lights.  The installation is fairly simple and requires roughly 4 hrs. Both the grille’s plastic substructure and the lower opening need to be modified by sawing out specific areas. Detailed instructions, fastening materials and electric connections are included in the delivery. Mounting behind the radiator grille is also possible.  Specifications for XPL Curved Lightbar: LEDs: 5W per LED Housing material: aluminium Light colour temperature: 6000 Kelvin Voltage: 9-32V DC Current: 3.12A~8.96A@24V DC - 6.25A~17.92A@12V DC Vibration resistance: 21 Grms Lens material: Polycarbonate Smooth backlight Proprietary IRIS reflector technology Curved high power light bars Weatherproof Deutsch connector with plug-and-play wiring harness Certifications: CE, RoHS, IEC 62471, ECE R112 Thanks to our iris reflector technology and the unique curve of the bar, the XPL Curved series produces a wide spot beam pattern with a range of over 600 metres. Scope of delivery: Complete radiator grille set for New Defender with XPL-HC23 light bar, brackets and wiring harness including detailed installation instructions.

Complete set of AUTOTERM Air 2D parking heater for Defender The parking heater set AUTOTERM (Planar) 2D12 for the Land Rover Defender consists of all important components needed for the installation of a parking heater. Included in the delivery are the AUTOTERM 2D 12 Volt parking heater, our Nakatanenga parking heater console, the Nakatanenga mounting plate, a fuel tank extraction, a Webasto air outlet with 60 mm connection, 30 cm warm air pipe and a vibration damper.As a low-priced and powerful alternative to our Webasto parking heater kits, the AUTOTERM (=Planar) 2D parking heater is proving to be a real sales hit. This is partly due to the particularly compact dimensions, which allow installation even in small cars, vans, off-roader motorhomes, construction machinery, boats or in difficult installation situations. In the off-road / 4x4 sector, it is ideally suited for the "typical" off-road vehicles such as Land Rover Defender, Mercedes G or Jeep Wrangler JK.These are only a few of many reasons why we now offer the AUTOTERM (Planar) 2D 12 V parking heater in a clear and comprehensive complete set for the Land Rover Defender at an economical price. For both the Tdi/ Td5 and the Td4, we offer one set each with a perfectly matching accessory kit.You can select different front panel cut-outs for the parking heater console included in the scope of delivery. The associated connections are available in the classic cigarette lighter format (12 V) or as 5 V USB charging sockets for Apple iPhones, navigation devices, iPads and smartphones and are included in the scope of delivery.The parking heater can also be operated while driving.Running time: The AUTOTERM parking heater switches off automatically after 2 hours of operation. However, as soon as you press a button during operation, the parking heater continues to run indefinitely until it is switched off manually.Scope of delivery:- AUTOTERM 2D parking heater 12 volt incl. silencer, intake air hose, heat protection hose, tank intake pipe and corrugated exhaust pipe.- Optionally analogue control unit simple control (PU-5) with rotary control or digital control unit comfort control (PU-29) with time switch- Nakatanenga parking heater console incl. the selected connections- Nakatanenga mounting plate- Fuel filler cap- Webasto air outlet with 60 mm connection, rotatable- 30 cm warm air pipe (diameter: 60 mm)- Vibration damper- Fixing material (screws, nuts, clamps, shrink hose, cable ties)Technical data:- Fuel type: diesel- Heating capacity: max. 1.8 kW, min. 0.8 kW- Volume of heated air: max. 75 m³/h, min. 34 m³/h- Fuel consumption in operation: max. 0.24 l/h, min. 0.1 l/h- Power consumption in operation: max. 29 W, min. 10 W- Weight: 3 kg (independent heater)- Manual start/stop → On the Autoterm.cz site you will find a calculator for the correct dimensioning of the air heater,You can choose between two control elements:- Simple Control (PU-5) element with rotary control: The old PU-10 control element had a relatively inaccessible control surface. Therefore, the reliable control element with rotary control is now the new improved standard of the Planar parking heaters! With the rotary control, you can adjust the heating power of the parking heater and regulate the power of the ventilation in ventilation mode! The PU-5 control element with rotary control can also be purchased separately here.- The digital control element comfort control (PU-29) with timer has an OLED display and an understandable and clear interface.  Temperature, ventilation and power can be configured via the display and the various buttons. With the timer, you can easily set the start of the parking heater to a specific time. The digital control element with timer can also be purchased separately here.Setting options comfort control (PU-29):- Temperature and power (adjustable for the parking heater, the control panel and for an external heater).- Time and date - Operating language (English or Russian)Functions of the timer comfort control (PU-29):- Memory function: save the time so that the parking heater starts at this time every day - Configurable memory locations: Up to 3 different weekdays with different times can be set and saved. The AUTOTERM (=Planar) 2D12 is equipped with an altitude kit.This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heat output decreases proportionally to the amount of oxygen in the air. Roughly speaking, from 2,000 metres the loss of output per 500 m altitude is approx. 5%. Manufacturer tests up to 3,440 m were trouble-free. Up to 4,000 m no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not yet be tested at real altitude. Important:Especially when used at high altitude, the free travel of the fan is extremely important!Route the combustion air intake and exhaust extremely short and with low resistance - i.e. no kinks, no blockage or reduction. It should also be noted that operation beyond 3,000 m is still a technical compromise. Again, care should be taken to ensure that the combustion chamber is properly heated on a regular basis. The chamber must be burnt free of soot deposits. Soot deposits can also form on heaters that are permanently operated at the lowest setting. Therefore, the following still applies: No guarantee for sooty combustion chambers!In order to ensure the longevity of the heater, you should also free-burn it occasionally at low levels. The combustion chamber reaches full temperature after running at full load for about half an hour. Normally, no further maintenance is required. In case of extreme loads, e.g. during longer overnight stays at more than 4,000 m, the combustion chamber including the seal set should be cleaned if necessary. To heat your roof tent using your auxiliary heating system, we offer an installation service for a warm air duct through a ventilation plate. https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Cannon Race CR-7 - 70 Watt - SPOT BEAM DRIVING LIGHT Ultra-Bright 15.330 Raw Lumens Per Pair Broad Spot Beam Pattern with 458m of Distance and 60m. Wide SAE/DOT & ECE Approved Clear and Selective Yellow Lens Options Shatterproof Polycarbonate Lens The Cannon Race Series 7 LED (CR-7) delivers the highest performing spot beam to hit the market. The CR-7 utilizes a truly unique lens that performs as well as it looks. With a broad spot beam that reaches 458m long and 60m wide, the CR-7 outperforms and outshines the competition with ease.The CR-7 utilizes only top-binned 10W LEDs from CREE that allows the CR-7 to blasts a massive 15.330 lumens (pair) out of only a 114mm housing. Never let dust, fog or rain slow you down again. The selective yellow lens will allow your CR-7 to cut through any tough weather while maintaining maximum output.Virtually unbreakable, the CR-7 uses a powerful polycarbonate bezel that won't crack, fade or corrode like traditional aluminum bezels. Ready for the most extreme environments the CR-7's are submersible and watertight with a IP68/69K housing that is capable of withstanding any adventure you can throw at it. Features: LEDs: 7 x 10W Housing Material: aluminum Light Colour Temp: 5600 Kelvin Dimensions: 114/121/74mm Weight: 0.62 kg Voltage: 9-32V DC Amperage: 2.92A@24V DC - 5.84@12V DC Vibration Rating: 21.2 Grms Lens Material: Polycarbonate Certifications: CE, RoHS, ECE R112 Weatherproof Deutsch Connector

Nolden 7-inch Gen 2 Bi-LED Headlights: Illuminate the night and give your Defender the ultimate look! Now also available in All-Black = Stealth Edition! Do you love your Land Rover Defender, but the original headlights let you down in the dark or bad weather? Then it's time for an upgrade that not only provides brilliant illumination but also gives your off-road classic a modern and premium touch: the Nolden 7-inch Generation 2 Bi-LED Reflector Headlights! More light, more safety, more style – for your Defender: These high-end headlights are the result of German engineering and set standards in terms of light output, durability, and design. Say goodbye to dim halogen light and experience the road and terrain ahead in a whole new clarity. Brilliant Bi-LED Technology: Experience significantly brighter and more uniform illumination than with conventional headlights. The Bi-LED function combines low beam and high beam in one module, ensuring a seamless transition and impressive range. This means for you: You see obstacles earlier and drive safer – whether on a dark country road or in the deepest terrain. Plug & Play Installation: Developed as a direct replacement for your Defender's original 7-inch headlights. Installation is straightforward and requires no complex vehicle modifications. Extremely durable and maintenance-free: LED technology is not only more energy-efficient but also significantly more durable than halogen lamps. No more annoying bulb changes! These headlights are built to withstand the harsh conditions your Defender is exposed to. Modern look with a classic touch: The Nolden headlights blend perfectly with the Defender's iconic design while giving it a modern, high-quality appearance. The clear lens and thoughtful reflector design make them a real eye-catcher. (Depending on the chosen variant, e.g., in Chrome, you further enhance the premium look). With E-certification mark – road legal: Naturally, these premium headlights have the necessary E-certification, so you can drive legally and without concerns on public roads. Features at a glance: State-of-the-art Nolden LED low beam and high beam, LED daytime running light, and position light in fiber optic technology Significantly improved light output and visibility Perfect fit for Land Rover Defender (replaces original 7-inch headlights) Long lifespan and high energy efficiency Weather-resistant and robust Elegant design that enhances your Defender With E-certification mark for legal road use Treat your loyal companion to the light upgrade it deserves! With the Nolden 7-inch Generation 2 Bi-LED Headlights, you invest in safety, durability, and an unbeatable look. Turn night into day and enjoy every drive with perfect visibility! A few more details: Over 30,000 hours LED lifespan White road illumination, similar to Xenon H4 connectors for Plug & Play Standard 7” mounting (PAR56) Die-cast aluminum housing 480 h salt spray test Available in Chrome, Dark-Chrome, Matte-Black, and All-Black Approvals: ECE and EMC Technical Data: Low beam: 23 W High beam: 33 W Daytime running light: 8.5 W (fiber optic) Position light: 1.2 W (fiber optic) Dimensions: 177 mm LED Type: OSRAM Voltage: 12/24 V Weight: 880 g Tested: ECE, EMC Ventilation: Nitto Denko Air Cap Housing material: Diallyl Diglycol Carbonate (ADC) Lens material: Hardened PC (Polycarbonate) Temperature range: -40°C to +80°C Vehicle wiring: FLRY Connector: H4 for main headlight, Tyco/AMP Superseal for position light Reference number: 12.5 The Nolden LED headlights are available in Chrome, Dark-Chrome, and Matte-Black and are delivered with a cable set for position and daytime running lights. The set includes 2 headlights and 2 stainless steel mounting rings. Should you also want to replace the mounting kit during the headlight change, we have the following products for you: Fitting Kit Headlight Land Rover Defender Fitting Kit Headlight Land Rover Defender, stainless steel

Powerful light, easy installation – Vision-X GEN2 Cannon LED Bring light to unexplored territories with this headlamp! HYBRID ALUMINUM-POLYCARBONATE HOUSING The Light Cannon features a housing made of both aluminum for increased strength and polycarbonate for weight reduction. UNIVERSAL MOUNTING WITH ONE SCREW Designed for easy installation, the LED Light Cannon features a sturdy, single-screw universal mounting system. STANDARD FORM FACTOR The Light Cannon LED combines the benefits of LED lighting, including low power consumption and 50,000 hour life, with the standard form factor of a conventional HID or halogen lamp. Specifications: Range approx. 350m ECE R112 approval as a driving lamp LEDs: 1 x 40W Housing material: Hybrid Color temperature: 6.000 Kelvin dimensions: 121,6 / 134 / 93,7 mm Weight of one headlamp: 0.91 kg Voltage: 9-32 V DC Current rating: 1.67A@24V DC - 3.33A@12V DC Vibration Rating: 21.2 Grms Lens material: acrylic Certifications: CE, RoHS, IEC 62471 IP68 / IP69K

Increased brightness for long-distance and close-range illumination Especially when driving on country roads and unpaved paths, increased visibility can be an important safety factor. The LEDriving® Functional Series FX Gen 2 portfolio provides additional close-range and far-field illumination on dark roads. Even in poor visibility conditions or at dusk, the high-performance LEDs achieve a range of up to 635 metres and daylight conditions with a colour temperature of 6000 Kelvin. The auxiliary headlamps of the FX series impress with a special reflector design and not only provide a modern and appealing look, but also reduce glare for more visibility in road traffic. They can be used both as additional LED headlights and as powerful worklights. Both versions of the lights are fully ECE-compliant and therefore suitable for use in road traffic. In addition, OSRAM has developed a special mounting kit that is compatible with all auxiliary headlamps of the FX Gen 2 series for individual mounting. Versatile in use, they defy numerous environmental influences and are particularly light and at the same time robust and resistant thanks to high-quality materials such as the aluminium housing and the stable polycarbonate lens. Complete reverse polarity protection prevents damage due to overvoltage and contributes to a longer service life. The FX series auxiliary lights have been tested and validated in a DIN-certified environmental simulation laboratory for extreme external influences with regard to water, dust, shock, heat, cold and permanent vibration in accordance with the highest IP & IK protection classes IP6K8 & IP6K9K. Their variability gives the FX series a flexible range of applications. They can be fitted to cars, trucks, agricultural machinery, commercial vehicles, construction vehicles, caravans, off-road vehicles and quads. OSRAM provides a 5-year warranty on these products. Product details:OSRAM LEDriving® auxiliary headlamp Lightbar FX1250-CB SM GEN 2 | LEDDL134-CB SM Features: COMBO BEAM = Combined beam characteristics for both far-field and near-field illumination. Light beam of 630mLuminous flux: 11,000lm, rated power: 176W Cold white light with 6000K For 12V & 24V vehicles DTP04-2P, DTP06-2S connector, cable length: 1200mm Over- and undervoltage protection Single mount certified1) (2x ECE R149), ECE R10, ECE (Ref. 2x 50). Highest protection classes: IP6K8 & IP6K9K Robust and durable - shatterproof polycarbonate lens and die-cast aluminium housing with special black coating Efficient reflector design with 45 OSRAM high-power LEDs Side brackets included 5-year OSRAM guarantee 1) Product description: Outstanding illumination, performance, quality, form, durability and functionality. Maximum optical efficiency, effectiveness and homogeneous light distribution Coverage of far-field illumination Perfectly matched to individual requirements and needs for multivariant use Special reflector design for an attractive and modern appearance and reduced glare Robust and resistant - for a long service life Increased safety off-road and on-road ECE-compliant and approved for use in road traffic Fields of application: Cars, trucks, 4x4s, ATVs, agricultural vehicles, commercial vehicles, construction vehicles, quads, caravans, etc.1) Exact conditions at: www.osram.de/am-garantieNote: Single mount - no installation in pairs necessary, as two certified light sources are used.  

Nakatanenga Outdoor Storage Box Pro – premium protection for genuine off-road adventures Travelling by 4x4, camper or expedition vehicle calls for more than an ordinary plastic crate. The Nakatanenga Outdoor Storage Box Pro is made for demanding use: a rugged off-road storage box designed to protect gear on dusty trails, rough tracks and in challenging weather. Recovery gear, tools, camping kitchen equipment and travel essentials stay protected and easy to organise. IP67 waterproof and dustproof – ready for demanding terrain The rotomoulded shell is made of high-impact polyethylene with a 3.6 mm wall thickness and is built to cope with knocks, vibration, dirt, dust and hard-going off-road use. It provides IP67 dust and water protection, while UV-8 stabilisers add high resistance to prolonged sunlight. With the box correctly closed, its contents remain protected even during long journeys in persistent rain and heavy downpours. This makes it particularly useful for roof racks and open load beds, where storage boxes are exposed to weather, wind and occasional contact with branches. For the stated water and dust protection, the lid, latches and drain valve must be fully closed. Organised from the inside – modular storage included Rather than being a simple empty cargo chest, the Pro series comes with a modular interior organisation system. An elastic lid net keeps flat essentials close at hand, while removable storage trays offer a separate level for small tools and accessories. The included dividers can be installed or removed as required, helping separate different types of gear and reduce unwanted movement while travelling without sacrificing flexibility for your individual loadout. Pro 50: 1 lid net, 1 removable tray, 2 removable dividers. Pro 90: 1 lid net, 1 removable tray, 2 removable dividers. Pro 110: 1 lid net, 2 removable trays, 5 removable dividers. Easy to secure – integrated strap guides and tie-down points all around Integrated strap guides and tie-down points on every side make it easier to secure the box with appropriate ratchet straps or other suitable tie-down equipment. This is particularly useful on roof racks, in pickup beds and in vehicle storage systems. The boxes are also stackable to help build an organised, space-saving setup. Always secure cargo correctly and observe vehicle and rack load ratings. Drain valve on every size – one feature, several practical uses All three box sizes feature a drain valve that lets you release collected water or melted ice without tipping the entire box over. With ice or cooling packs inside, the box can also function as a passive ice chest or cooler – for drinks, for example, or when transporting fish. The valve also makes cleaning easier after wet or dirty equipment has been carried or something has leaked inside. There is no active refrigeration; the valve must be closed for watertight transport. Padlock-ready and designed for practical use Robust plastic latches hold the lid closed. Suitable padlocks can be fitted at the designated locking points (padlocks not supplied). Side handles make the box easier to carry, and a sturdy metal bottle opener permanently screwed to the body adds a convenient detail at camp. Reflective details – easier to spot after dark Reflective elements on the outside make the box easier to see when light falls on it – at camp, during night-time loading and unloading or when it is placed next to the vehicle. They help make the box outline more visible in low-light conditions. Off-road, overlanding, camping and expedition use As a 4x4 cargo box, waterproof equipment case, camping storage box or vehicle load-space organiser, the Pro range works for recovery gear, spares, tools, kitchen equipment and travel essentials. It can also be carried on roof racks and pickup load beds when secured correctly. Filled with ice or cooling packs, it can also serve as a passive cool box or ice chest – for drinks and food, for example, or for transporting fish. Meltwater can be drained easily through the integrated drain valve. The hard-wearing design is equally at home in garages and workshops. Three sizes – one premium range The Nakatanenga Outdoor Storage Box Pro comes in grey and three sizes: approximately 50, 90 and 110 litres. Every model includes a lid net, removable storage trays and dividers matched to its size. Specification Pro 50 Pro 90 Pro 110 Capacity approx. 50 L approx. 90 L approx. 110 L External dimensions(L × W × H) 59.5 × 46.6× 33.7 cm 83.0 × 46.8× 37.15 cm 120.0 × 46.8× 33.6 cm Internal dimensions(L × W × H) 47.5 × 33.1× 22.65 cm 71.0 × 33.1× 25.5 cm 108.0 × 32.3× 21.6 cm Weight approx. 6.75 kg approx. 10.5 kg approx. 14.0 kg Included internal organisers Lid net 1 1 1 Storage trays 1 1 2 Dividers 2 2 5 Why pay more for a premium off-road storage box? There are certainly cheaper storage boxes available. Many rotomoulded cases even look almost identical at first glance. The meaningful differences are often found in the details: the grade and formulation of the plastic, wall thickness, structural design, reinforcements, latches, hinges, seals, drain valves, tie-down options and interior organisation all contribute to how a box performs when it matters. We have deliberately chosen to offer only high-quality boxes that we have tried ourselves and take on our own off-road trips and expeditions. That decision is backed by more than 30 years of hands-on off-road experience and feedback from customers. When you're far from the nearest town, discovering that a supposedly waterproof box lets rain inside is the last thing you want. Suddenly, the money saved at checkout does not feel like much of a saving. Our philosophy is simple: buy cheap, buy twice. That does not mean every lower-priced box is poor quality. It means we choose not to compete for the lowest price. The Outdoor Storage Box Pro is built for the kind of use our customers actually put their equipment through: roof racks, rough trails, dust, mud, rain and branches. Durability, weather protection and thoughtfully engineered details are more than marketing phrases to us – they're the standard we stand behind. That is why this is a premium storage box. Padlocks, tie-down straps, ice and cooling packs are not included. Cooling is passive only; no active refrigeration.

Modular vehicle panel for the Land Rover New Defender 110 With the old Landy, it was common practice to simply drill into the aluminium bodywork to fit rails or brackets for off-road and expedition kit. With the New Defender’s stylish bodywork, that would, of course, be sheer madness. Nevertheless, you’ll still want to be able to securely carry all sorts of things on the outside of the vehicle. One of the most elegant mounting options is undoubtedly our versatile MOLLE panel for the rear of the vehicle – which can be fitted on the left or right.   The sturdy panel, made from black powder-coated aluminium, allows for the safe transport of anything that is MOLLE-compatible or can be secured using straps, clips, Quickfists or similar fastening systems. The Fixplus Straps from our shop, for example, are ideal for this purpose.   The main advantage: Valuable storage space inside the vehicle remains free, while equipment you would rather not keep in the cabin can be carried outside. This includes jerry cans or a muddy shovel, for example. The panel is particularly useful for recovery equipment: When things get difficult off-road, recovery straps, shovels and other essential items are easily accessible from outside the vehicle. No searching through a fully loaded boot, no moving luggage out of the way – the equipment you need is right where you can quickly reach it.   The maximum load capacity is 25 kg – roughly equivalent to a 20-litre canister of water or fuel.   Fitting the panel is extremely simple and fully reversible, as it requires no drilling or other permanent modifications. Simply remove the plastic trim strip on the rear mudguard of the New Defender. The wall plugs supplied are then inserted into the clip slots. An aluminium profile is first attached to these, onto which the Airline rail for mounting the panel is then fitted. On the roof side, installation is carried out either on the roof rails.   All necessary fixing materials are included in the scope of delivery.   Dimensions: W 775 mm x H 550 mm Max. load capacity: 25 kg   The panel suitable for the New Defender 90 is in the pipeline!

Door seal sets for Land Rover Defender - Perfect fit & robust for any terrain Whether replacing classic standard equipment or retrofitting for better sealing: Our selection of door seal sets for the Land Rover Defender offers the right solution for almost every model and year of manufacture. The high-quality seals (original or replica) ensure noticeably less wind noise, reliable protection against water and dust - particularly important for off-road driving or daily use in all weather conditions. Choose from different sets for driver and passenger doors, rear doors and side doors - all custom-fit, durable and easy to fit. More comfort. Less noise. Better sealing. Make your Defender fit for every adventure - with the right door seals from our range.    

NOLDEN LED high beam headlights, 70mm Set of 2, with E-mark, for installation   Technical data: Dimensions: 69.2x55 mm LED: 1x LED 13 W Fastening: 2x M6 Approval: ECE (E-mark) Material: Aluminum   Color: Black or chrome - please select.

Alloy wheel for Suzuki Jimny 2 GJ/HJ High Peak J-02, 6x15" offset: -5 After the great response to the J-01 wheel, we wanted to do something different with the second original design. We present you the HIGH PEAK J-02 15-inch alloy wheel, front. While the J-01 offers a classic design with a deep lip, the J-02 features a concave seven-spoke design reminiscent of off-road motorsport. Specifically designed for the Suzuki Jimny JB74 (2018+, designated as 'GJ' & 'HJ' in the EU). TÜV type approved and strength tested. Also compatible with JB43 (1998-2018) models. Made in Italy. Guaranteed European quality Bolt-on mounting with standard or raised chassis. No additional modifications required (depending on tyre size). Rim size : 6x15"OFFSET : -5Bore / PCD : 5x139.7Finish : anthracite or vintage whiteWeight : 9.2kgVehicle : Suzuki Jimny II GJ/HJ If you need a complete wheel set, please contact us by e-mail or phone.info@nakatanenga.de☎ +49 9181 466 644

Oberland Arms TitanSepp Integral TiBronze The Oberland Arms TitanSepp, designed by renowned Italian knife designer Tommaso Rumici, has become a true classic after more than 11 years in production. With the new Integral version, this proven concept reaches an even higher level in terms of material, craftsmanship and design. The new TitanSepp knives are manufactured by premium knife maker Lionsteel in Maniago, Italy – using state-of-the-art machinery combined with the expertise of highly skilled craftsmen. The standout feature of the new version is the one-piece integral handle, precision-milled from solid titanium or aluminium and available in two colour variants each. This places the new TitanSepp firmly in the premium class when it comes to quality, design, materials and finish. All knives come as standard with a MOLLE-compatible nylon knife pouch. The pouch is manufactured by TacticalBear in Germany and impresses with its robust construction and versatile usability – for example, it can also be used as a magazine pouch or accessory pouch. Our Knife Secure retention system is available separately as the perfect matching accessory. Legal certainty through BKA classification As one of the few knives on the market, the TitanSepp offers additional legal certainty through an official classification notice issued by the German Federal Criminal Police Office, the BKA. This document can be conveniently downloaded via the discreet QR code laser-engraved on the handle scale. According to the BKA classification notice, the TitanSepp knives are not classified as weapons, but as true two-hand opening knives in accordance with §42a paragraph 1, §1/2/2-a-, §1/2/2-b- and §2/3 of the German Weapons Act. You can find the BKA notice under the ‘Documents to download’ tab. For the export market, as well as for authorised use in Germany, a one-hand opening version of the TitanSepp will also be available soon. Details / Features / Specifications Blade length: 93 mm / 3.5 mm Steel: M390, black PVD, stonewashed blade Handle material: titanium, bronze PVD Handle dimensions: 125 mm / 12 mm Weight: 172 g Concept / original design: Matthias Hainich Design: Tommaso Rumici Manufacturing: Lionsteel, Maniago, Italy Accessories: includes MOLLE-compatible nylon knife pouch, manufactured by TacticalBear in Germany BKA classification notice: QR code discreetly engraved on the handle scale, included at no extra cost Serial number: each knife is marked with an individual consecutive serial number

Vision-X Expora spotlights Explora by Vision X LED auxiliary lights are the next generation of driving lights developed by Vision X for Explora, which are brighter, better and easier than ever to illuminate the surroundings. The Explora series combines Vision X high quality with efficient LED diodes – to deliver driving light at an unbeatable price!   With the Explora by Vision X LED driving lights, you no longer have to choose between a long or wide light pattern. Explora has unique reflectors, which provide a hybrid light beam, with both length and width, without any dark spots.   Explora by Vision X is an LED driving light with outstanding performance.   All models of Explora are E-marked, with Vision X E-boost. With E-boost, you can selectively increase the power of the LED diodes, for additional brightness. But even without E-boost, the Vision X Explora delivers a powerful light with length and width.   The Vision X Explora series is offered as both LED driving lights and LED light bars. What they all have in common is that they are incredibly durable – with lamp housings made of high-quality aluminum and lenses made of almost unbreakable polycarbonate. The driving lights and light bars all have brackets in super strong and durable composite to resist corrosion. Explora by Vision X is of course also dust and water resistant, with full IP68/IP69K rating. The entire Explora series meets the standards ECE R10, ECE R148 and ECE R149.   Last but not least, Explora by Vision X are incredibly easy to mount and install. These LED driving lights have a built-in smart control unit, so they only need to be connected to a power source and setup with clearly color-coded cables to the correct function.   Vision X Explora LED driving lights include wiring, nuts and brackets for installation. The driving lights also include a cover, which is easily mounted/removed when needed.   Properties: Unique reflectors that provide both width and length of the light E-marked driving lights with E-boost for extra effect Tasteful white or orange position light High durability with IP68/IP69K rating General data:  Estimated LED life: 50,000 hours Colour temperature: 5700K Light pattern: hybrid (length + width) Voltage: DC11-32V Lens: polycarbonate Lamp housing: aircraft aluminium Bracket: composite IP class: IP68/IP69K Vibration class: 6.9 gRMS Operating temperature: from -40°C to +60°C Certifications: ECE R10, ECE R148, ECE R149, CE, UKCA, RoHS, REACH E-marked: Yes Daten  7 Zoll 120W  9 Zoll 200W Watt: 120W 200W E-amplifier: 80W 130W Raw lumen: 8160 lm 13600 lm Effective lumen: 6000 lm 9700 lm LED: 24 x 5W 40 x 5W Light length: 386 m @ 1 Lux (460 m in pair) 480 m @ 1 Lux (700 m im in pair) Light width: 40 m @ 1 Lux (45 m in pair) 50 m @ 1 Lux (60 m in pair) Power consumption: 5,8A @ 13,5V  9,6A @ 13,5V Width: 186 mm  221 mm Height: 186 mm 225 mm Depth: 85 mm 102 mm Weight: 2 kg 3 kg  

Heater and Blower Control Unit for Land Rover Defender Td4 When the blower slider stops working: complete control unit as a direct replacement The heater and ventilation controls in the Defender are used regularly over many years – and often not exactly gently. One well-known weak point of the control unit is the slider used to adjust the blower speed. As the vehicle gets older, this slider can become stiff, develop excessive play or fail completely. If the slider is faulty, the desired blower setting – particularly the middle speeds, in our experience – can no longer be selected reliably. This is especially frustrating when the windows are misted up, during winter or in poor weather conditions. With this complete heater and blower control unit, you can replace the faulty unit and restore reliable operation of the heating and ventilation system. The benefits: Complete heater and ventilation control unit Ideal replacement for a faulty or stiff blower speed slider Controls blower speed, temperature and air distribution Direct replacement for the existing control unit Suitable for: Land Rover Defender L316 Defender Td4 2.4: 2007–2011 Defender Td4 2.2: 2012–2016

The new Oberland Arms Alu SEPP - two-handed knife The aluminium SEPP, created by renowned Italian designer Tommaso Rumici, has long since become a modern classic.The latest generation is now being produced by premium manufacturer Lionsteel in Maniago, Italy - with high-precision technology and the expertise of experienced craftsmen. The special feature: an integral handle milled from solid aluminium that meets the highest standards of design, ergonomics and workmanship.This puts the new Alu SEPP in the absolute top class - uncompromising in terms of quality, function and aesthetics.The scope of delivery includes a MOLLE-compatible knife pouch made of robust nylon, colour-matched to the knife and manufactured using a precise laser-cut process. Manufactured in Germany, the pouch is also ideal as a magazine pouch or for other tactical equipment.Technical details:   Blade length: 95mm/3.5mm   Steel: M390 stonewashed / black PVD   Handle material: Aluminium 7075 black or green hard anodised 7075  Weight: 133g   Concept/Initial design: Matthias Hainich   Design: Tommaso Rumici   Production: Lionsteel, Maniago Italy   Accessories: incl. Molle compatible knife pouch made of nylon, manufactured by Tactical Baer in Germany   All Titan Sepp knives come with QR code with the BKA notification discreetly engraved on the handle (at no extra charge)   All knives are provided with a consecutive serial number The knives are not subject to the weapons prohibition under §42a Weapons Act, because they are not one-handed knives. You can find the corresponding notice of determination from the BKA above under documents! At explicitly designated weapons prohibition zones, the knives, just like any other knife, may not be carried.

The striking design looks light and elegant on heavy vehicles. 20-inch chrome alloy wheel for New Defender Data: Wheel size: 9x20" ET: 37 Bolt pattern: 5x120 Colour: chrome, black Special features: suitable for winter use 

Seat covers for Suzuki Jimny I Small as ever, but even more oho! That's the Jimny. Not an SUV for transporting the kiddies to riding school, but a real off-roader with a Twingo-like footprint of just 3.65 x 1.65 metres. Since the Jimny is a traditional workhorse with limited interior space, every cubic centimetre of free space counts. Off-the-shelf seat covers can't do this, they slip, overhang, get stuck or snag on moving parts. That's why our high-quality covers are tailor-made and fit extremely precisely thanks to individual Velcro straps. This also applies to the perfectly fitting headrest protector. As one of the last true off-road vehicles, the Jimny is particularly popular with foresters, fishermen, farmers and other 4x4 enthusiasts. Dirt, dust and animal residues therefore stay better on the easy-to-clean 100% nylon slipcovers than in the seats themselves. But of course our covers can do even more: in addition to a generous zipped pocket, high-quality Molle on the back of the front seat covers ensures clever expandability of the storage space. For example, our practical bag set can be attached here, the first aid scissors can be stowed within easy reach or the tensioning and fastening strap set can be used to secure everything that otherwise likes to fly around. Of course, the covers are also airbag-compatible. Available for: Suzuki Jimny I  Set consists of: Driver's side, passenger's side Colour: Coyote, Black,  Material: 100% Nylonwashable 30-60° C Made in EU! Please select the desired variant and colour. You will find illustrated instructions (for Jimny GJ/HJ) under documents. This article was designed in our in-house tailor shop. A dedicated team and short distances allow for continuous quality control and further development of our textile products. And if you already have a tailor's workshop in house, then it is easy to also accept customer change requests, special designs, suggestions and proposals for improvement at short notice and to implement them as far as possible. Mail or phone call is all it takes! And by the way: For this product, we use nylon fabric with a polyurethane (PU) coating. Both the fabric and its coating are PVC-free. Flexible PVC materials may contain phthalate-based plasticisers, some of which are legally restricted due to their potential health risks. That's why we deliberately avoid PVC in this product and opt for a high-quality PU coating instead – a more expensive alternative for us, but one we've consciously chosen.

Service Kit for Land Rover New Defender L663 – Maintenance in original equipment quality Complete filter set for routine maintenance of the Land Rover Defender L663 – available for various engine versions. This service kit includes the essential filters and an oil drain plug for routine servicing of the Land Rover Defender L663 from model year 2020 onwards. All components are of OE matching quality and are matched to the respective engine version. Regular maintenance and timely filter replacement help maintain the engine's performance and long-term reliability. This kit provides the required components for a filter change in one package, eliminating the need to order each part separately. The service kit is suitable for use in professional workshops as well as for maintenance carried out by experienced vehicle owners. Scope of Delivery 1 × Oil filter 1 × Engine air filter 1 × Cabin air filter / Pollen filter 1 × Oil drain plug Vehicle Compatibility Vehicle: Land Rover Defender L663 (New Defender) Model year: From 2020 onwards Engine: Available for various engine versions – please select the appropriate option from the drop-down menu. Quality: Replacement parts in OE matching quality Important Notes Engine oil is not included and must be purchased separately. Before ordering, please check your vehicle's engine version and select the corresponding kit. Always follow the vehicle manufacturer's specified maintenance intervals and engine oil specifications.

Nakatanenga gift voucher worth €200 Whether for outdoor fans, off-road enthusiasts or Land Rover enthusiasts: There is guaranteed to be something for everyone in our extensive shop. The shopping vouchers can be redeemed for all our goods and services. Immediately after payment, you will receive a high-quality gift voucher in printed form free of charge. For those who are in a hurry:We will also be happy to send you the voucher by e-mail as a PDF file for you to print out yourself. Depending on the payment method, you will then usually receive the voucher on the same day as your order. The vouchers are valid indefinitely.

Imwoid Sepp - He's back! We are pleased to be able to offer a popular OA classic in an improved form.The perfect shape and the ingenious handle have remained.The handle has been extended with a countersink on both sides that can serve as a grip aid for reversegrip or as a guide for a bowdrill.The blade steel has been upgraded to N690.Top quality manufactured in Maniago/Italy by Viper Tecnocut. Design by Tommaso Rumici Technical data: Blade length 95mm blade thickness 3,7mm Blade width approx. 30mm steel N690 58-59 HRC Flat ground Dark Stonewashed PVD handle length approx. 110mm handle thickness approx. 14,8mm G10 olive or black with 0,8mm spacer of G10 orange handle scales with 2 hollow screws and countersink for bowdrill sheath Kydex with LOK by Vegaholster Concept Matthias Hainich Design Tommaso Rumici Made in Italy by Viper Tecnocut Choice of colour: Black or olive Important notice: The knife is not subject to a carrying ban in Germany. Sale of knives only to persons over 18 years and against proof of age. Please send us a copy of your ID (front and back) as proof of age.

Tool Roll Hungry Mini - now also with WMF chef's knife - FREE! With this additional chef's knife, all common cutting tasks can be carried out effortlessly: The larger chef's knife is ideal for slicing and chopping solid ingredients, while the smaller preparation knife is perfect for finer work. Both knives impress with their long-lasting sharpness and hardened blades made of stainless, acid-resistant special steel, which is also coated. The ergonomically shaped handles fit perfectly in the hand and offer a secure grip. Thanks to the practical protective blade covers, the knives can be stored safely and space-savingly in the cutlery drawer.   Tool Roll Hungry Edition, incl. Camping Cutlery The Defender represents English cultural heritage, just like a scrumptious picnic with cucumber sandwiches and Scotch Eggs. At Nakatanenga we thought, that’s not just a very good combination on a country estate in Somerset, but anywhere, really, where the Great Outdoors meets fine dining. And that’s why we’ve equipped our tried and tested Tool Roll with exquisite cutlery: et voilà, the Tool Roll Hungry Edition was born, available in Mini, Maxi and Titan! Instead of the usual camping sets with tin bowls, plastic sporks and aluminium knives, we offer stainless steel cutlery in the Tool Roll Hungry Edition Mini and Maxi as well as high-quality WMF cutting knives with heat-resistant and ergonomically shaped plastic handles. The Mini-set is designed for four people and the Maxi Edition for six, with a chopping board and a four-piece cooking spoon set made from durable bamboo. If you have to watch the weight of your equipment or you’re generally fascinated by great materials, the Tool Roll Hungry Mini Titan is the one for you. Being harder than steel, titanium allows for extremely thin manufacture of cutlery, plates, mugs and so forth while maintaining incredible robustness and durability. As a result, titanium utensils are generally even lighter than their aluminium equivalents, while providing all the health-related and hygienic advantages of stainless steel. The titanium fork and spoon sets can also be purchased separately. Whether you go for stainless steel or titanium, everything fits neatly into the space-saving roll-up bags made of durable nylon. Carrying strap and loops on the underside of the Maxi-Roll expand transport and combination options.  And of course, the 12 pocket slots still provide space for other essential items. Can opener, corkscrew or maybe just the lobster tongs? No matter how you roll food-wise, whether it’s hot dogs or Foie Gras for you, the Tool Roll Hungry Edition is an unbeatably practical piece "Home from Home" for campers, off-roaders and foodies. Scope of delivery Tool Roll Mini Hungry: 1x Tool Roll MINI4x knife (dishwasher safe)1x WMF utility knife (Not suitable for dishwashers)4x fork (dishwasher safe)4x big spoon (dishwasher safe)4x coffee / teaspoon (dishwasher safe) Scope of delivery Tool Roll Mini Hungry Titan: 1x Tool Roll MINI6x knife (dishwasher safe)1x WMF utility knife (Not suitable for dishwashers)6x fork titan (dishwasher safe)6x spoon titan (dishwasher safe) Scope of delivery Tool Roll Maxi Hungry: 1x Tool Roll MAXI6x knife (dishwasher safe)1x WMF utility knife (Not suitable for dishwashers)1x WMF chef's knife (Not suitable for dishwashers)6x fork (dishwasher safe)6x big spoon (dishwasher safe)6x coffee / teaspoon (dishwasher safe)1x 4-piece bamboo cooking spoon set (dishwasher safe)1x bamboo cutting board (Not suitable for dishwashers) MADE IN EU And by the way: For this product, we use nylon fabric with a polyurethane (PU) coating. Both the fabric and its coating are PVC-free. Flexible PVC materials may contain phthalate-based plasticisers, some of which are legally restricted due to their potential health risks. That's why we deliberately avoid PVC in this product and opt for a high-quality PU coating instead – a more expensive alternative for us, but one we've consciously chosen.