Shop by vehicle

All the nooks and crannies in your Defender attract and hold water or wet dirt, which makes them a hotbed for corrosion – small wonder that the door areas are often affected by rust. Especially the C pillars in 4/5-door models frequently require replacement in Defender restorations because fittings, screw holes, undersides and the gaps between struts and body panels are a breeding ground for corrosion and often develop critical damage. Instead of piecemeal repair with angle grinder and welder, it’s often preferable to swap the entire component. We are offering individual C posts for the right or left side of all models where door seals are only pushed in and not riveted. If you have riveted seals, they need to be adapted. If you prefer to replace the entire door frame with B and C posts and also the sill, you can find the entire set here.

Nakatanenga Overhead Storage System Defender Where to put important small items when the storage space in the vehicle cockpit is tight? It's simple! Into the pockets of our Overhead Storage System. Even items that are only needed in an emergency are then within easy reach.In addition to a space-saving bag, the innovative Overhead Storage System contains a base plate that is attached between the sun visor and the car roof. In various bundles, you can then decide whether the plate with radio holder is intended for the driver's or passenger's side. In the case of the base plate with radio holder, a suitable holder for the CB handset is also included in the scope of delivery. This holder uses the three attachment points of the centre mirror.The bag and plate are available in black and grey. As an alternative to the Albrecht radio, other radios with similar dimensions (104 x 100 x 25 mm) can also be attached. No additional holes are required for the base plates, as the existing holes in the sun visor are used for mounting.The bags are manufactured according to US military standards (MIL-SPEC) and our specifications by Delta Bags in Germany. The bag for the plate with radio holder is smaller due to the holder. Can be ordered either individually or in sets.Technical dimensions:Bag standard: 480x150x20 mmBag radio version: 375x150x20 mm

Console for headliner - for Defender 90/110/130 This roof console for the Land Rover Defender (90/110/130) brings some desperately needed storage space to the cabin of the vehicle. The console has not only a large storage compartment but also a DIN slot allowing for a radio or switches to be mounted. We recommend our own Nakatanenga switch bundle, for easy installation  Remarks: Easy installation by simply following the integrated manual  Comes with the necessary hardware Rear-view mirror remains at the same spot This consol is not suitable for soft-tops The Sun visors need to be shortened The original dome light can be detatched and mounted inside the console. In the rear of the console a second OEM dome light can be mounted or some more switches. By upgrading to a second doemlight now even the read seats get some light. The Rear view mirror can be mounted just where it was before. The console is available in truckcab/ singlecab for all vehicles produced from 03/2013 or all other Stationwagons and doublecabs. Please select.

Double DIN Console for TD5, 2002-2007 The MUD Td5 Double DIN Console replaces the factory 2002-2007 Td5 Defender radio bezel with this exclusive, one-piece design that allows you to easily upgrade the original single DIN radio setup to a double DIN head unit. The original Land Rover radio bezel installed in the 2002-2007 Td5 Defender is a fragile unit that can break thanks to a flimsy and poorly designed two-piece assembly that can barely support the weight of the single-DIN head unit. Typically, the separate center panel that contains the head unit/radio breaks off the main console. The MUD Td5 Double DIN Console is a simple DIY upgrade that uses the factory fasteners and requires no cutting, drilling or modification to your dash. Simply remove your old console, replace it with the MUD Double DIN Console, and enjoy the benefits and features of the larger screens found on modern double DIN head units, such as Apple CarPlay & Android Auto screen mirroring. The MUD Td5 double DIN console was designed using CAD 3D scanning technology and uses an injection molding manufacturing process for a factory fit appearance and a perfect fit every time. Available in Matte Black

Track Rod and Drag Link - set heavy duty Set of steering track rod and drag link with three greasable heavy duty track rod ends. Fits all Land Rover Defender from MY1986 until today (incl. Td4).

Chequer plate for bonnet incl. rivets for Defender up to MY07, black powder coatedIllustration symbolicMaterial thickness: 2.5 mm basic thickness / 4 mm incl. checker (quintet plate)

The striking design looks light and elegant on heavy vehicles. 20-inch chrome alloy wheel for New Defender Data: Wheel size: 9x20" ET: 37 Bolt pattern: 5x120 Colour: chrome, black Special features: suitable for winter use 

Set of locking wheel nuts for Land Rover Defender 90/110/130 Suitable for:- Original Land Rover rims- Retrofit rims that use the original Land Rover wheel nuts Not suitable for:- Borbet / CW- Performance TX1- steel rims The set comes with 5 locking nuts, so you can secure your entire vehicle including the spare tire. The set is supplied with the necessary hardware. Scope of delivery:5 x nuts incl. caps1 x spanner

Seat cover for driver and passenger side Ineos Grenadier The Ineos Grenadier is designed to be the successor to the old Land Rover Defender. You won’t find any gimmicks in the Grenadier but loads of functionality and robust simplicity. This principle also applies to the front seats by Recaro. While they provide a lot of support off-road, they are at the same time quite comfortable, both when driving and when getting in or out of the car. Regardless whether you choose the Recaros with leather or fabric upholstery, our tailor-made protective covers for the Grenadier’s front seats function as a sturdy and versatile "battle suit" for tough off-road missions, long overland trips and everyday life. Our textile designers opted for a three-part concept to achieve a perfect fit for the compact, straight-lined seats. Apart from the headrest, there are two separate covers for backrest and seat. This allows for a firm and precise fit without bulging or sliding. The covers are fastened with straps (or velcro) and tucked into the gaps for an even tighter fit, both at the outer edges and between the backrest and the seat. The materials - 1000D nylon 6.6 and breathable nylon mesh - are hard-wearing and, above all, easy to clean. MOLLE on the headrest, backrest and the front edge of the seat offers additional storage space to attach equipment and accessory pouches. Cut-outs in the covers guarantee that operation, functionality and safety technology (e.g. airbags) remain unrestricted. Our seat covers are available in black with plain-colored MESH inserts. Material: nylon, PU-coated This item was designed in our in-house textile workshop. A dedicated team and short distances guarantee constant quality control and continuous development of our textile products. Thanks to our in-house workshop, we can easily accommodate customer requests for changes, custom designs and ideas for improvement at short notice. We promise to implement your requirements whenever possible. An email or phone call is all it takes! And by the way: at Nakatanenga we exclusively use materials with a 100% nylon PU coating for textile products. In contrast to PVC, nylon PU (polyurethane) is free from harmful phthalate-based plasticizers. Until recently, low-molecular phthalates were the most common plasticizers and are even used in food and cosmetics. However, due to their molecular nature, they accumulate in the environment and are suspected of acting like endogenous hormones. From a toxicological point of view this is considered a trigger for various diseases, including cancer. For Nakatanenga, it is therefore a matter of course to use only ecologically sound and health-friendly alternatives such as nylon PU.  

TREKFINDER underride guard for SUZUKI Jimny II type GJ BJ 2018 front axle suitable for all Jimny models of the type GJ built from the end of '2018 suitable for all engine and transmission types suitable for all Vorderachsausführungen made of 5 millimeters of steel yellow galvanized including all mounting parts attachment to original points of the vehicle super stable and flat heavy duty version

Borbet LD Alloy Wheel for Your Land Rover Defender (8x16"): Style Meets Robustness on Any Terrain Your Land Rover Defender is more than just a vehicle – it's a statement, a loyal companion for adventures, and a workhorse. To optimally support its legendary capabilities and simultaneously give it an individual, strong look, choosing the right wheels is crucial. The Borbet LD alloy wheel in the 8x16 inch format, the successor to the popular CW 8x16", available from us at the Nakatanenga Offroad Shop, is an excellent choice for this. Why Borbet LD for Your Defender? For decades, Borbet has stood for first-class quality and innovative design in the wheel market. The LD wheel was specially developed with the requirements of robust off-road vehicles like the Land Rover Defender in mind. It combines an attractive appearance with the necessary stability and load capacity for demanding use – on the road and off-road. The Advantages of the Borbet LD 8x16" Alloy Wheel: Improved Appearance: Give your Defender a more distinctive and modern look. The classic, robust design of the Borbet LD perfectly matches the Defender's strong character and underscores its off-road DNA. Weight Reduction: Compared to heavy steel wheels, alloy wheels can reduce the overall weight of your vehicle and, in particular, the unsprung masses. This can have a positive effect on handling, agility, and potentially also on fuel consumption. Optimal Dimension for Off-Road Tires: The 8x16 inch format offers an excellent base for many common and high-performance off-road tire sizes. The 8-inch width often allows for the mounting of slightly wider tires, which can lead to a larger contact patch and thus improved traction off-road. The 16-inch diameter simultaneously allows for a decent tire sidewall height, which is important for comfort and off-road capability. Robust Construction: Even though it's an alloy wheel, the Borbet LD was designed for the stresses of off-road operation. It offers a high load capacity and is resilient enough to cope with the challenges off the beaten track. TÜV-Approved Quality: Borbet wheels, and therefore also the LD, are subject to strict quality controls and generally have the necessary TÜV certificates for straightforward registration. This gives you security and ensures legal use on public roads. Corrosion Resistance: High-quality surface coatings protect the wheel from weathering, salt, and dirt, which increases its longevity. Notes: Tires shown are for illustration purposes only and are not included in the scope of delivery. The matching wheel nuts are included in the scope of delivery. Technical Aspects of the Borbet LD 8x16": Size: 8Jx16" Bolt Pattern: Suitable for Land Rover Defender (5x165.1 mm) Offset (ET): ET5; optimized for the Defender to ensure ideal track width and clearance. Load Capacity: Designed for the axle loads of the Land Rover Defender. Your Upgrade for Performance and Look at Nakatanenga At Nakatanenga, we carefully select our range to offer you only products that meet our high standards of quality and practicality. The Borbet LD wheel is one such component that not only visually enhances your Land Rover Defender but can also support its performance. Combine the Borbet LD wheels with the matching tires from our range to perfectly tailor your Defender's setup to your needs – whether for daily driving, demanding off-road tours, or expeditions. Give your Land Rover Defender the look and performance it deserves. Discover the Borbet LD alloy wheel in 8x16 inches now in the Nakatanenga Offroad Shop!

De-cat pipe for Land Rover Defender Td4 2.4 and Td5 2.5 replaces standard catalytic converter and thus reduces back pressure in the exhaust system. Better airflow of exhaust gases and thus better throttle response. In conjunction with other tuning options like K&N performance filter, chip tuning with performance intercooler und performance high-flow main silencer engine power can be increased noticably. Please note our fitting flat-charge! Please note that when fitting a de-cat pipe within the German road law your vehicle approval with be void.  The de-cat pipe fits all vehicle lengths (90/110/130). There are different pipes for Td4 (MY 2007-2011) and Td5 (My 2002-2006) engines. The de-cat pipe is not suitable for Defender Td4 2.2 (from MY2012) because of the particulate filter. Please choose the engine type.

Abenteuer4x4 - Recovery eye rear cross member Land Rover The recovery eye / towing eye from Abenteuer 4x4 has a 360° rotatable shackle pin made of stainless steel. The basic construction made of aluminium and stainless steel is screwed to the original mountings of the rear cross bar of the Land Rover Defender. In addition, a step with pulled knobs is integrated for easy access to the roof rack.Scope of delivery:    Spacer plate (10 mm aluminium, black powder-coated)    Carrier plate 1 with step (3 mm stainless steel, black powder-coated)    Carrier plate 2 (3 mm stainless steel, black powder-coated)    4 x 12 mm hexagon socket screw (stainless steel)    2 x 16 mm hexagon socket screw (stainless steel)    Bow shackle with 13 ton breaking load

Cargo net incl. fixing material, Suzuki Jimny II The smaller the car, the bigger the challenge to make the best use of available space inside. Our cargo mesh for the Suzuki Jimny II (from MY2018) will generate a lot of storage room in a place that’s rarely used: under the roof in the cargo bay.To attach the 93 x 60 cm netting to the roof trim, all you need to do is mount two aluminum frame elements in the front and the back. They are the same color as the mesh for a seamless look. The elastic cargo mesh can then be attached to the frame and the interior grab handles with 12 adjustable straps. To make it easier for you to fill the mesh space, there are also two click buckles in the front for easy access.Light and flat pieces of equipment, sleeping bags, textiles and the like will find the perfect storage space inside the mesh, even in a fully loaded Jimny.If you do not have handles on the headlining, 2 ring nuts are supplied to attach the net. Additionally, you can thread an elastic string in a zigzag shape on the underside of the netting for all those lighter items you want quick access to: light blankets, towels, swimming or sports gear etc.The cargo mesh comes in the colors black, gray and coyote. Please note: When ordering, please be sure to state in which model (GJ or HJ) you would like to install the Cargo Net, and also whether you have an interior light (Comfort Plus equipment) in the GJ model. Pictures may vary.

Window grille for Land Rover Defender 90/110 Window grille, for Land Rover Defender 90/110, for the rear side windows, material: aluminium, anodized, black powder-coated, 1 piece, delivery incl. blind rivets Please also note our optional safety mounting set for these grilles. Suitable for the rear side window of the Land Rover Defender 90/110 or windows of the same size (108x45 cm) Dimensions for mounting: Hole spacing horizontal: 112 cm Hole spacing vertical: 49 cm    

Robustness Meets Style for Your Off-Road Adventure Are you looking for a wheel that not only looks great but can also withstand the tough conditions অফ-road? Then the Borbet CW Design alloy wheel in 8x16 inch is the perfect choice for you and your off-road vehicle. Strong and Reliable Off-Road This wheel was developed for real challenges. With an impressive load capacity of 925 kg per wheel, it's perfect for your Discovery or Defender (90/110/130, with a reduction in load capacity to 1,850 kg on the rear axle). Whether it's rocky trails, muddy tracks, or demanding inclines – you can rely on the Borbet CW. Design That Impresses In addition to its robustness, the Borbet CW captivates with its classic yet striking design. You have the choice between a classy black powder coating (RAL9005) or an elegant silver paint finish. This allows you to give your vehicle an individual touch that is sure to turn heads. Technical Details That Speak for Themselves: Manufacturer: Borbet Brand: CW Design Size/Offset: 8x16", ET 5 Colors: Black powder-coated or Silver painted Suitability: Discovery, Defender 90, 110, and 130 (note details for load capacity reduction) Load Capacity: 925 kg Certification: Available for various tire sizes (e.g., 245/70, 255/85, 265/75, 285/75). Please note that for some tire sizes, a suspension lift may be required according to the certificate. A single vehicle approval may be possible. Note: For some tyre sizes, a suspension lift from Taubenreuther is required in the expert opinion. If this is not installed, these tyre sizes can still be registered if the inspector confirms the clearance of the tyres by individual approval. Experience has shown that the costs for this are around 70 euros - but may vary locally. Everything Included for a Quick Start The scope of delivery includes the wheel itself as well as the matching wheel nuts. So you can start with the assembly right away and prepare your vehicle for the next adventure. Choose the Borbet CW Design alloy wheel now and equip your off-roader with a wheel that makes no compromises in terms of quality, stability, and appearance!

Underride protection TREKFINDER for SUZUKI Jimny II type GJ and HJ REAR AXLE made of 5 mm steel yellow galvanized suitable for all Jimny models of the type GJ built from the end of '2018 suitable for all engine and transmission types suitable for all rear axle versions made of 5 millimeters of steel yellow galvanized including all mounting parts attachment to original points of the vehicle super stable and flat heavy duty version

Scheelmann folding console for Land Rover Defender The Scheelmann seat console is suitable for all Land Rover Defender 90/110/130 series Td4, Td5 and Tdi. It can be used for the passenger or driver side of the vehicle and is foldable to allow easy access to the battery. It also serves as a seat rail extension. A TÜV certificate (in conjunction with a Scheelmann seat) is included.Scope of delivery:    one console    running rails    fixing material    TÜV certificate

Water cooler For Land Rover Defender Td5

Nakatanenga cable set winch mounting in Defender In order to facilitate the installation of the winch in the Defender and to minimise sources of error, we have a complete cable set for this purpose mass-produced by a cable harness manufacturer. The cable lengths are adapted to the installation situation in the Land Rover Defender 90/110/130. Due to the cable cross-section of 50 mm², even high currents can be transmitted safely, so that enough current reaches the cable winch and is not converted into heat in the cable. Delivery includes tubular cable lug M10 and battery pole clamp minus M10, for mounting on the vehicle's wiring.

Black wheel nuts for Land Rover Defender up to MY 2016 alloy wheels For a cohesive look down to the last detail: these black wheel nuts are the perfect complement to alloy wheels on the Land Rover Defender up to model year 2016. Whether you need a single replacement nut, a complete set of wheel nuts or a lockable version – you’ll find the right option for your vehicle here.   The black finish is not achieved through a simple paint job or coating. Instead, the surface of the steel caps is treated using a special process to ensure they appear permanently black. This makes the wheel nuts particularly resistant to mechanical stress and chemical influences.   Ideal for anyone looking to give their alloy wheels a clean, finished look whilst relying on robust, practical components. The wheel nuts ensure a harmonious overall look, particularly on black or dark rims.   Advantages at a glance Suitable for Land Rover Defender up to MY 2016 Suitable for alloy rims Black, durable surface Available as a single nut, 23-piece set or lockable 5-piece set Discreet appearance for a high-quality wheel finish The wheel nuts for Land Rover Defender are NOT suitable for the CW Borbet 8x16“ rims (suitable wheel nuts for the CW Borbet 8x16” rims can be found here)! However, they can be used with other alloy rims such as Hutchinson, Kahn, ZU and similar.

Underride protection for Land Rover Defender Underride protection with two heavy duty recovery eyes for all Land Rover Defender, robust three-part construction, steel 4mm, with welded-in 4mm reinforcement in the impact area, optionally hot-dip galvanised or hot-dip galvanised and black powder-coated Underride protection suitable for all Land Rover Defender from 1983 to today    skid plate made of 4 mm thick steel, with welded-in 4 mm reinforcement in the impact area    galvanised or galvanised and black powder-coated as desired    Side parts made of 8 mm thick steel, galvanised (black)    with two robust heavy duty recovery eyes    The underride guard is attached to the original mounting points using the original vehicle bolts. The complete other installation material is included.Material info:Passivation is the spontaneous formation (aluminium, nickel, titanium...) or targeted creation of a protective layer on a metallic material, which prevents or very much slows down the corrosion of the base material.Attention: The shackles shown are not included in the delivery.Please select the desired surface.

Power and earth distributor for 12 consumers, for installation in the Land Rover Defender TD4, incl. pre-assembled cable set and pre-fuse. Cable length: 150 cmCable cross-section: 50 mm²

Seat covers for Suzuki Jimny I Small as ever, but even more oho! That's the Jimny. Not an SUV for transporting the kiddies to riding school, but a real off-roader with a Twingo-like footprint of just 3.65 x 1.65 metres. Since the Jimny is a traditional workhorse with limited interior space, every cubic centimetre of free space counts. Off-the-shelf seat covers can't do this, they slip, overhang, get stuck or snag on moving parts. That's why our high-quality covers are tailor-made and fit extremely precisely thanks to individual Velcro straps. This also applies to the perfectly fitting headrest protector. As one of the last true off-road vehicles, the Jimny is particularly popular with foresters, fishermen, farmers and other 4x4 enthusiasts. Dirt, dust and animal residues therefore stay better on the easy-to-clean 100% nylon slipcovers than in the seats themselves. But of course our covers can do even more: in addition to a generous zipped pocket, high-quality Molle on the back of the front seat covers ensures clever expandability of the storage space. For example, our practical bag set can be attached here, the first aid scissors can be stowed within easy reach or the tensioning and fastening strap set can be used to secure everything that otherwise likes to fly around. Of course, the covers are also airbag-compatible. Available for: Suzuki Jimny I  Set consists of: Driver's side, passenger's side Colour: Coyote, Black,  Material: 100% Nylonwashable 30-60° C Made in EU! Please select the desired variant and colour. You will find illustrated instructions (for Jimny GJ/HJ) under documents. This article was designed in our in-house tailor shop. A dedicated team and short distances allow for continuous quality control and further development of our textile products. And if you already have a tailor's workshop in house, then it is easy to also accept customer change requests, special designs, suggestions and proposals for improvement at short notice and to implement them as far as possible. Mail or phone call is all it takes! And by the way: At Nakatanenga we only use materials with 100% nylon PU coating for all textile articles. Unlike PVC, nylon PU (polyurethane) is free of harmful phthalate-based plasticisers. Until recently, low-molecular phthalates were the most common plasticisers for plastics of all kinds and are even used in food and cosmetics. However, they accumulate in the environment and are suspected of acting like endogenous hormones due to their molecular nature. This is highly questionable from a toxicological point of view and is considered to be a trigger for various diseases, including cancer. For Nakatanenga, it is therefore a matter of course to use only ecologically and health-safe alternatives such as nylon PU for the coating of textile products.

Defender One Touch Indicator Upgrade Defender - from late 300Tdi to current 2016 -2.2TDciThis complete plug and play upgrade adds the functionality of new vehicles equipped with lane change or 3 flash indicators to your Defender. With a simple momentary press of the indicator stalk the indicators will flash 3 times.Note - Please check on 300Tdi models you have the later style wiring connectors to confirm this you will need to remove the lower steering cowl.

Take a Deep Breath – with the Raised Air Intake for Your Land Rover Defender! Your Defender is built for adventure. But what if those adventures take you through deep water crossings or extremely dusty tracks? This is precisely where our raised air intake, also known as a snorkel, comes into play and becomes an indispensable companion for your Land Rover Defender 90, 110, or 130. Imagine crossing a river. With a standard air intake, you risk water getting into the engine – an expensive problem you can avoid. Our raised air intake relocates the intake point to roof height. The result: a significantly reduced risk of engine damage from water. But that's not all! The snorkel also shows its strengths in dry, dusty regions. The air at roof height is cleaner and contains fewer dust particles than near the ground. This means your air filter gets dirty slower, needs to be cleaned or replaced less often, and your engine can breathe more freely. This snorkel, made of robust black plastic, even comes with an integrated cyclone filter that pre-separates coarse particles, further increasing efficiency. Installation is on the right side of the vehicle, and thanks to the EU-wide valid TÜV parts certificate, registration is no problem either. So, you're not only safer but also legally on the road. Your advantages at a glance: Optimal Engine Protection: Significantly reduces the risk of water damage during river crossings. Cleaner Intake Air: Less dust and dirt enter the engine, which protects your air filter and extends its lifespan. Integrated Cyclone Filter: For even more effective pre-separation of dirt particles. Robust Design: Made from durable, black plastic. TÜV Parts Certificate: For hassle-free registration (valid EU-wide). Perfect Fit: Suitable for Land Rover Defender 90/110/130, models 300Tdi, Td5, Td4 2.4 & Td4 2.2 (Puma/TDCI). Easy Installation: On the right side of the vehicle. Equip your Defender for real challenges and ensure it always gets the best air to breathe. With this raised air intake, you're prepared for any terrain! With EU-wide valid TÜV parts certificate! Suitable for Land Rover Defender 90/110/130, 300Tdi, Td5, Td4 2.4 & Td4 2.2 (Puma/TDCI)

Large differential guard with skid plate and hardware for the P38 rear axle of a Land Rover Defender 110/130 from the model year 2002 From the model year, 2010 on two holes need to be drilled. Not many parts on any 4x4 are as exposed as the front and rear differentials. That's why even a small hit out on the trail can lead to an abrupt end to your trip and an expensive visit to your local shop. Something like that would be annoying in your local offroad park but can become extremely dangerous in rural areas of the world. That's why we have designed the perfect diff guards for the different Land Rover Defender axles, allowing for maximum protection and the occasional skid across obstacles.

LED fog lights in chrome with E-mark (therefore registration free mountable), Plug&Play solution for Jeep Wrangler JK 2007-2010, for numerous other Jeep/Dodge/Chrysler vehicles also suitable, different colours, price per piece. Plug&Play: 2007-2010 Jeep Wrangler 2009 Dodge Journey 2005-2008 Dodge Magnum 2006-2010 PT Cruiser Modification of the cable assignment necessary: 2011-2015 Jeep Wrangler 2010-2012 Dodge Journey 2011-2012 Jeep Grand Cherokee 2011-2012 Dodge Charger 2005 Chrysler 300 Technical data: Light output: 1,080 lumens (raw), 610 lumens (effective) Approval: ECE (Reg.10 and Reg.19), DOT (FMVSS 108) Operating voltage: 12 V Power consumption: 1.6 A @ 12 V Lens: UV-resistant, coated polycarbonate Housing: aluminium Colour: chrome  

Nakatanenga parking heater console 2 New version of the proven parking heater console, it allows the installation of a parking heater (e.g. Webasto Airtop 2000 STC, Eberspächer Aitronic D2 or D11C or AUTOTERM (=Planar 2D12)) under the cubby box of the Land Rover Defender 90/110/130, turning it into an armrest at a comfortable height (158 mm higher). The display of the parking heater is recessed into the front panel of the console.Please note: New holes have to be drilled for the installation of the parking heater console; the required fixing material is included in the scope of delivery.The ever-growing need for power sources in the vehicle cockpit - whether in the classic cigarette lighter format (12 V) or as a 5 V USB socket for Apple iPhones, navigation devices, iPads, smartphones or similar. - the new generation of the Nakatanenga parking heater console now also meets these requirements in the best possible way: it is optionally available with heavy-duty 12 V sockets and/or USB charging sockets from the marine sector. These are then already included in the scope of delivery, so they do not have to be ordered separately. A Webasto air vent can be attached to the cut-out at the rear. In the cut-out for the Planar parking heater, the display is glued on and the cable is fed through the square hole. If none of the front panels contains your desired cut-outs, you can order the front panel without cut-outs and process it accordingly.Basic dimensions: 47.5 cm x 26.5 cm x 15.5 cmATTENTION: An AUTOTERM Air 4D (=Planar 44d) is not recommended for this purpose!

Thule roof bar for Land Rover vehicles Thule roof bar for Land Rover vehicles, optionally for Land Rover Defender or Land Rover Discovery 1 / 2, consisting of two crossbars and feet in suitable height for rain gutter mounting.Thule roof racks or roof bars have been synonymous with quality and safety for decades, even under tough conditions. They are therefore ideally suited for mounting roof tents, roof boxes, equipment carriers of all kinds and much more.Technical data:    Load capacity: 100 kg (dynamic, i.e. while driving).    Max. roof load Roof load: according to vehicle manufacturer's specifications    Material feet: sheet steel, galvanised, powder coated, Pebax coating    Material of crossbar: Square steel tube, powder-coated    Assembly: Quick assembly without tools using central nut    Lockable: No, but can be retrofitted with lockable tommy nuts    Foot height: Suitable for Discovery I / II or Defender 90 / 110 / 130    Length of cross struts: 150 cm    Foot height: 20 cmPlease note the maximum roof load of the vehicle according to the manufacturer's specifications!Please select your vehicle type.

AIR INTAKE / AIR INTAKE WOLF XD STYLE, year of construction 1994-2016 „Wolf“ Military Defenders see action in all climate zones and all kinds of environmental conditions. From the wet and cold in the north to the mud of the tropics and the sand and dust of the deserts. One specific modification for these extreme challenges can be spotted with the naked eye: the air intakes. When not equipped with snorkels, XD Landy-wolves feature raised air intakes, often on both sides, to keep water, mud and dust out of the intake system. If you want to give your civilian Landy (with intake on the right) this military Wolf look, you can replace the standard grill with our Wolf XD Style Air Intake. This is not only a great visual upgrade to your Defender, but also protects your intake system from splash water, mud and dust. Due to its design, the Wolf Style intakes will already pre-filter a lot of unwanted stuff getting near your intake, especially when compared to the standard grills. So, if you’re aiming at an upgrade in design and performance, but don’t want to spend the 600 € or more for the hard-to-get original parts (ESR4570), the Wolf XD Style Air Intakes are the ones for you. For off-roaders with truly amphibious ambitions, who rather have water in the footwells than the intakes, we recommend our SN4 or SNX snorkels, of course. Installing the Wolf Style Air Intake is really easy. The frame can be attached to the pre-existing screw holes. The intake itself and the gasket are then in turn attached to the frame. All fastening materials are included. Delivery: Frame, intake case, gasket, fastening material. Will only fit Defenders with air intake on the RIGHT. Please note: Depending on the year of manufacture, the hole pattern on the fender may not match the hole pattern of the retaining frame exactly and adjustment work may be necessary.

Trim for rear door - Land Rover Defender up to MY 2002 (90 and 110) Rear door trim that replaces the old vinyl covered hardboard and ugly gray trim. This trim is a tough, attractive all-in-one design that really beautifies the interior of the Defender. attractive design all-in-one design flexible storage net (map bag) included in the kit easy installation, does not require special tools 1 - 2 hours installation time robust, scratch-resistant plastic material