Wear kit with tank extraction and exhaust pipe for AUTOTERM Air 2D / 4D  For our portable heater boxes, we only use AUTOTERM (previously Planar) Diesel heaters. After assembly, we are usually left with unused accessories and spare parts from the original AUTOTERM delivery, so we decided to bundle them as wear and tear replacement kits for only 20 € incl. VAT. That’s a massive price reduction of nearly 70% when compared to the individual value of these spare parts.The sets will fit AUTOTERM 2D and 4D air heaters and consist of one fuel pick-up tube, one fuel line, one exhaust pipe including heat insultation and various pieces of fastening materials. These are essential spare parts and replacements to keep handy in case of damage or wear and tear.

The temperature sensor / probe enables a more accurate measurement of the temperature. This temperature sensor can be mounted as a third sensor (in addition to the two temperature sensors built into the heating and control panel); for example, in the living or sleeping area. The cable is 5 m long and protected by a corrugated tube. Suitable for AUTOTERM Luft 2D / 4D (formerly Planar 2D, 4D and 44D) parking heaters. Note: 1 temperature sensor can be connected per heater.

Installation flange air heater for floors up to 48mm NEW: EVO version with even better thermal decoupling of the 4 fixing bolts!This flange allows the installation of an air heater in floors or walls with up to 48 mm wall thickness. Suitable for the Webasto and Eberspächer D2 parking heater.While an air heater is normally only suitable for installation in thin sheet metal walls or floors, with this flange an insulated floor construction with a wooden panel or directly a sandwich panel up to 48 mm thick can also be used. There is no need to scribe and drill the many different holes for combustion air, flue gas, fuel line and fixings - these are already integrated in the flange and allow the heater to be mounted directly in any direction. Only a rectangular cut-out of approx. 88x130 mm is required.Procedure:    Find a suitable flat installation location with max. 48 mm total thickness (e.g. floor panel+insulation+wood panel).    Cut a rectangular cut-out 88x130 mm.    Insert the installation flange with sealing compound and screw it in place.    Insert the heater from the inside into the flange and mount all hoses etc. from the outside.Stainless steel, laser-cut, welded, partially glass-bead blasted.Suitable for AUTOTERM air heaters (=Planar) 2D, 4D and 44D, as well as heaters with the same flange pattern from Eberspächer and possibly Webasto.

Precisely fitting base plate for parking heaters in Land Rover Defender 90, 110 & 130 Stainless steel mounting plate for auxiliary heating for all popular independent vehicle heaters (Webasto Airtop 2000 STC, Planar 2D12, Eberspächer) simply replaces the centre seat box cover underneath the cubby box of your Defender. All necessary cuttings to fit the heating unit and piping. The mounting plate fits all Land Rover Defender 90/110/130. Attachment with existing mounting material. Please note that you also need the Nakatanenga auxiliary heater console to fit an independent heating unit. The cubby box is fitted to this console. https://www.nakatanenga.de/media/pdf/74/df/0c/Merkblatt-Edelstahl-und-Rost.pdf  

Planar 2D Auxiliary Vehicle Heater We offer the Planar 2D auxiliary vehicle heater as a well-priced, powerful alternative to our Webasto auxiliary vehicle heater kits. With their compact size and a heater output of 1.8 kW, the Planar 2D is well-suited for fitting to smaller vehicles, vans, off-roaders, camper vans, boats or in confined spaces. It is ideal for 'typical' off-road vehicles like the Land Rover Defender, Mercedes G oder Jeep Wrangler JK. The extensive fitting kit that is supplied with each heater make fitting easy. The Planar 2D can be easily controlled via its analogous control unit, with 8 settings available from 0,8 - 1,8 kW heat output. Available as both, 12 volts or 24 volts, this heater is European market approved (ECE label) and can thus be fitted independet of TUV approval. The parking heater has approval for the European market (ECE test mark) and can therefore be installed without registration. The hole pattern is the same as that of Eberspächer Airtronic and Webasto AirTop 2000 heaters, so that an old unit could easily be replaced without drilling additional holes.A space-saving version with a 90° angle can be found here.  All Planar auxiliary vehicle heaters are extremely long-lasting and durable, as well as very frugal. The heater can also be used while driving. And extensive range of additional equipment is available in our online shop. Attention Defender drivers: Our extensive Planar full-set for Land Rover Defender not only includes everything needed to perfectly fit the heater to your Tdi, Td5 or Td4 Defender, but also offers considerable savings over the individual purchase of all included items. Comes with: - 12 V or 24 V heater- Optionally analogue PU-5 control panel with rotary control or digital Comfort Control control panel with timer- Thomas Magnet P327" dosing pump- Exhaust silencer- Dosing pump rubber holder- Dosing pump wiring harness- Heater wiring harness- Intake air hose with integrated silencer- Heat protection hose- Exhaust pipe end piece + clamp- Tank intake pipe- 5.5 m fuel line- 300 mm fuel line connector- 1 m corrugated metal exhaust pipe- Fastening material (screws, nuts, clamps, heat-shrink tubing, cable ties)- Operating instructions Technical details: ·         fuel: diesel·         heat output: max. 1.8 kw, min. 0.8 kw·         air volume: max. 75 m³/h, min. 34 m³/h·         fuel consumption: max. 0.24 l/h, min. 0.1 l/h·         power drain: max. 29 W, min. 10 W·         manual start/stop→ On the Autoterm.cz website you will find a calculator for the correct dimensioning of the air heater The AUTOTERM Luft 2D (Planar 2D) is equipped with a height kit!This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents shooting of the combustion chamber when the atmospheric oxygen content drops. The max. Heating power drops in proportion to the amount of oxygen in the air. Roughly one can say: From 2.000 meters the loss of power per 500 m height is approx. 5%. Manufacturer tests up to 3.440 m were no problem. No difficulties are to be expected up to 4.000 m. The software itself calculates up to 5.000 m - however, this has not yet been tested in real height. The separately available control unit with timer (optional extra) features a larger OLED display and more intuitive operation. Temperature, ventilation and output can be configured via a display and various switches. An added timer clock allows you to set the heater to a specific time. OLED display provides maximum visibility with minimum power drain.  Possible settings:- temperature and output- time and date- language (English or Russian) Features of the new timer clock:- daily: one fixed time at which the heater starts each day- individual: up to thee different settings with different days and times. To heat your roof tent using your auxiliary heating system, we offer an installation service for a warm air duct through a ventilation plate. The improved new control unit is also available separately.  https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment