Module for 12 Volt AUTOTERM parking heaters With this module and a suitable radio remote control, you can control AUTOTERM (Planar 2D12 and Planar 44D12) parking heaters. You need the module to assign the parking heater to a channel of a radio remote control. You can thus switch the parking heater on and off by remote control. A connection diagram is included in the scope of delivery.

Simple control panel (PU-5) for Planar parking heaters The control panel offers easy operation of the Planar parking heaters. The heater can be switched on or off manually via the control elements. Furthermore, the heat output can be regulated via the control panel.Control elements: Planar-5M  1. switch ventilation off/on2. switch heating on/off3. LED light to indicate the status of the heater    - yellow light = heater running    - slow, red flashing = malfunction4. LED light for status display of ventilation    - Green light = ventilation running    - green flashing = ventilation off    - yellow light = heating and ventilation are on together5. rotary control

VW T5/T6 heater bracket for AUTOTERM 2D parking heater This holder enables easy installation of the AUTOTERM (= Planar 2D parking heater) under the VW T5/T6. The mounting location corresponds to the factory-fitted air heater (passenger side between sill and longitudinal member). The holder is made of stainless steel and offers individually bendable mounting lugs for intake and exhaust silencers or similar. Only rivet nuts are required for installation, as there may not be any holes with threads in the carrier ex works.Optional: On the 4th and 5th photo you can see that the bracket can be combined with the stainless steel installation box (marked with blue lines) for the AUTOTERM 2D parking heater. The dimensions of the holder are adjusted in such a way that there is no collision with the car body. Attention: This still does not turn a parking heater into an underwater heater! You can order the installation box separately here.

Manifold T-piece for 75 mm hot air pipes - ideal for AUTOTERM & similar systems T-piece suitable for warm air ducts of Planar 2D auxiliary heaters and other independent vehicle heaters with 75 mm hoses.

Exhaust silencer for AUTOTERM (=Planar), Binar, Eberspächer parking heaters This stainless steel exhaust silencer is suitable for all parking heaters (air heating and water heating) with a 24 mm exhaust pipe.Suitable for the following heaters:    AUTOTERM Air 2D and AUTOTERM Air 4D (formerly Planar 2D, Planar 44D), AUTOTERM Flow 5D (formerly Binar 5D).    Eberspächer AirtronicAs the Webasto heaters have a 22 mm exhaust pipe, this silencer does not fit.Dimensions:    Outer diameter connection: 24 mm    Total length: 18 cm    Length of silencer without connections: 14 cm    Diameter: 40 mm (additional 2 cm fastening device)

Parking heater set for the VW T5 consists of all important components required for the installation of a parking heater. First and foremost, the set contains the AUTOTERM (=Planar) 2D12 parking heater, which is celebrated as an affordable and powerful alternative to Webasto and Eberspächer parking heaters. In addition to the heater holder with installation box, which can already be ordered individually and which was specially designed for the installation of the Planar parking heater in the VW T5, with this set we put together a comprehensive package for you with a matching hose clamp, fuel line, air duct, a warm air outlet and much more. As some components for the B-pillar vary depending on the vehicle model, please select the matching set for your VW T5 estate / panel van OR Multivan / Shuttle / California. Please note: This set is not suitable for vehicles with a partition wall! Scope of delivery: AUTOTERM 2D parking heater 12 volt incl. silencer, intake air hose, heat protection hose, tank intake pipe and exhaust corrugated pipeOptionally analogue control unit simple control (PU-5) with rotary control or digital control unit Comfort Control with timer switch5 metre connection cable for control panelSpecial heater bracket for VW T5, optionally with additional installation boxAir outlet for heating air 60 mm1 metre warm air pipe (diameter: 60 mm)60 mm to 90 mm adapterWarm air outlet for rear B-pillarAir duct for B-pillar incl. frameWarm air outlet for B-pillar frontAir ductFixing material (screws, nuts, hose clamp, cable ties)Technical data of the parking heater: Fuel type: dieselHeating capacity: max. 1.8 kW, min. 0.8 kWVolume of heated air: max. 75 m³/h, min. 34 m³/hFuel consumption in operation: max. 0.24 l/h, min. 0.1 l/hPower consumption in operation: max. 29 W, min. 10 WWeight: 3 kg (independent heater)Manual start/stop The AUTOTERM (=Planar) 2D12 is equipped with a height kit. This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heat output decreases proportionally to the amount of oxygen in the air. Roughly speaking, from 2,000 metres the loss of output per 500 m altitude is approx. 5%. Manufacturer tests up to 3,440 m were trouble-free. Up to 4,000 m no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not yet be tested at real altitude. Important:Especially when used at high altitude, the free travel of the fan is extremely important!Route the combustion air intake and exhaust extremely short and with low resistance - i.e. no kinks, no blockage or reduction. It should also be noted that operation beyond 3,000 m is still a technical compromise. Again, care should be taken to ensure that the combustion chamber is properly heated on a regular basis. The chamber must be burnt free of soot deposits. Soot deposits can also form on heaters that are permanently run at the lowest setting. Therefore, the following still applies: No guarantee for sooty combustion chambers! In order to ensure the longevity of the heater, you should also free-burn it occasionally at low levels. The combustion chamber reaches full temperature after running at full load for about half an hour. Normally, no further maintenance is required. In case of extreme loads, e.g. during longer overnight stays at more than 4,000 m, the combustion chamber including the seal set should be cleaned if necessary. To heat your roof tent using your auxiliary heating system, we offer an installation service for a warm air duct through a ventilation plate. We will be happy to advise you: ☎ +49 9181 466 644 https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Warm Air Where You Need It: The Highly Flexible 60mm Warm Air Ducting! Are you currently installing your parking heater or optimizing your existing system? Rigid, unwieldy hoses make your life difficult when it comes to directing warm air exactly where it's needed – whether in your camper, off-road vehicle, rooftop tent, or boat. With our highly flexible warm air ducting (inner diameter 60mm), installation becomes child's play! Its enormous flexibility allows you to master even complicated routing and tight radii without any problems. This makes our warm air ducting the first choice: Maximum Flexibility: Can be laid in the tightest installation spaces and around sharp corners without kinking or blocking airflow. This saves time and nerves during installation. Optimal Airflow: Despite its flexibility, the hose ensures good flow for efficient distribution of warm air from your parking heater. Robust Quality: Developed for the demands of a vehicle environment and resistant to the typical temperatures of a parking heater. Universally Suitable: With an inner diameter of 60mm, it is compatible with the connections of many common parking heater models – ideal for the AUTOTERM 2D parking heater, but also for Webasto, Eberspächer, and Truma heaters. As this hot air ducting is particularly flexible, we recommend it for use with our mobile air heater. Sold by the Meter for Your Needs: You order exactly the length you need for your project. This way, you avoid unnecessary waste and save costs. The hose is delivered as one continuous piece in the ordered length. Whether you want to direct the warmth specifically to the footwell, sleeping areas, or a particular area of your vehicle – this hose makes it easy. Notes: Inner diameter: Ø 60 mm Price per linear meter, sold only in whole meters. The pipe is completely waterproof. Example: If you need 3 meters of hot air ducting, add this item to your shopping cart 3 times. Please note: A maximum of 10 meters can be delivered in one piece. If you order, for example, 20 meters, you will receive 2x10 meters. Individual pipe sections can be connected without problems using the pipe connector. You can find a suitable storage bag for the hose here. Put an end to rigid solutions! Order your highly flexible warm air ducting now and enjoy cozy warmth exactly where you want it!

Durable 90° Stainless Steel Heater Bracket for Parking Heaters This high-quality stainless steel heater holder with 90 ° angle fits the following auxiliary heaters: Planar 2D parking heater Planar 4D parking heater Planar 44D auxiliary heating only with the same flange pattern: Webasto & Eberspächer

Water heater from Autoterm Engine preheater supplied with full installation kits, that includes: air intake hose with silencer, exhaust pipe with isolation, fuel pipe, mounting bracket, coolant pump and pipe, fuel pump and fuel stand pipe, control panel, muffler, tapered pipes, clamps, screws, wires etc. Advantages of the AUTOTERM Flow 5D (= Planar BINAR 5S): - Compact size (smaller size in comparison with other models);- The choice of installation options;- Exclusion of a cold start, which in turn extends the life of the engine;- Auxiliary function;- The reasonable price and high quality;- Low fuel consumption;- Self-diagnosis and outputting the display error. Technical data: Heating efficiency: 5 kWFuel consumption: 0.62 l/hHeater power consumption: 42 WFuel: DieselNominal supply voltage: 12 VWe are happy to advise you: ☎ +49 9181 / 466 644   https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Vibration damper for parking heaters Vibration damper for additional decoupling of the feed pump of a parking heater. Ideally suited for our AUTOTERM 2D and 4D (formerly Planar 2D and Planar 44D) parking heaters.Technical data:Diameter: 25 mmHeight: 20 mmThreaded bolt: M6x18

Warm air pipe 75mm for AUTOTERM Air 4D (=Planar 44D) parking heater Warm air pipe / flexible pipe / air pipe / warm air hose for effective distribution of warm air. The warm air pipe is optimised for the parking heater AUTOTERM Luft 4D (formerly Planar 44D). However, it is also suitable for Webasto, Eberspächer and Truma heaters.The warm air pipe is supplied according to current stock, so you could get one in black or in brown. Colours: inside silver and outside either black or brownInner diameter: Ø 75 mmPrice per running metre, delivery in whole metres only.

Nakatanenga parking heater console 2 New version of the proven parking heater console, it allows the installation of a parking heater (e.g. Webasto Airtop 2000 STC, Eberspächer Aitronic D2 or D11C or AUTOTERM (=Planar 2D12)) under the cubby box of the Land Rover Defender 90/110/130, turning it into an armrest at a comfortable height (158 mm higher). The display of the parking heater is recessed into the front panel of the console.Please note: New holes have to be drilled for the installation of the parking heater console; the required fixing material is included in the scope of delivery.The ever-growing need for power sources in the vehicle cockpit - whether in the classic cigarette lighter format (12 V) or as a 5 V USB socket for Apple iPhones, navigation devices, iPads, smartphones or similar. - the new generation of the Nakatanenga parking heater console now also meets these requirements in the best possible way: it is optionally available with heavy-duty 12 V sockets and/or USB charging sockets from the marine sector. These are then already included in the scope of delivery, so they do not have to be ordered separately. A Webasto air vent can be attached to the cut-out at the rear. In the cut-out for the Planar parking heater, the display is glued on and the cable is fed through the square hole. If none of the front panels contains your desired cut-outs, you can order the front panel without cut-outs and process it accordingly.Basic dimensions: 47.5 cm x 26.5 cm x 15.5 cmATTENTION: An AUTOTERM Air 4D (=Planar 44d) is not recommended for this purpose!

Fuel filler nozzle for Land Rover Defender Td5 2.5, Td4 2.4 and Td4 2.2 The fuel extractor for the Land Rover Defender 90/110/130 Td5 2.5, Td4 2.4 and Td4 2.2 enables the auxiliary heater to be supplied with diesel without the time-consuming and labour-intensive removal of the fuel tank.The fuel is extracted by looping the extractor into the hose between the vehicle's fuel nozzle and tank and is therefore possible without removing or drilling into the tank. The fuel dispenser is suitable for various parking heaters, including Webasto Airtop 2000 and Eberspächer Airtronic D2.The fuel filler cap can be flexibly bent, allowing you to control whether the parking heater can completely empty the vehicle's tank or whether a fuel reserve should remain. It is ideally suited for our AUTOTERM Planar heaters.Outer diameter: 59 mmMaterial thickness: 2 mmPlease note: This fuel filler is not suitable for TDI models, as these have a larger pipe diameter.

Planar 2D Auxiliary Vehicle Heater We offer the Planar 2D auxiliary vehicle heater as a well-priced, powerful alternative to our Webasto auxiliary vehicle heater kits. With their compact size and a heater output of 1.8 kW, the Planar 2D is well-suited for fitting to smaller vehicles, vans, off-roaders, camper vans, boats or in confined spaces. It is ideal for 'typical' off-road vehicles like the Land Rover Defender, Mercedes G oder Jeep Wrangler JK. The extensive fitting kit that is supplied with each heater make fitting easy. The Planar 2D can be easily controlled via its analogous control unit, with 8 settings available from 0,8 - 1,8 kW heat output. Available as both, 12 volts or 24 volts, this heater is European market approved (ECE label) and can thus be fitted independet of TUV approval. The parking heater has approval for the European market (ECE test mark) and can therefore be installed without registration. The hole pattern is the same as that of Eberspächer Airtronic and Webasto AirTop 2000 heaters, so that an old unit could easily be replaced without drilling additional holes.A space-saving version with a 90° angle can be found here.  All Planar auxiliary vehicle heaters are extremely long-lasting and durable, as well as very frugal. The heater can also be used while driving. And extensive range of additional equipment is available in our online shop. Attention Defender drivers: Our extensive Planar full-set for Land Rover Defender not only includes everything needed to perfectly fit the heater to your Tdi, Td5 or Td4 Defender, but also offers considerable savings over the individual purchase of all included items. Comes with: - 12 V or 24 V heater- Optionally analogue PU-5 control panel with rotary control or digital Comfort Control control panel with timer- Thomas Magnet P327" dosing pump- Exhaust silencer- Dosing pump rubber holder- Dosing pump wiring harness- Heater wiring harness- Intake air hose with integrated silencer- Heat protection hose- Exhaust pipe end piece + clamp- Tank intake pipe- 5.5 m fuel line- 300 mm fuel line connector- 1 m corrugated metal exhaust pipe- Fastening material (screws, nuts, clamps, heat-shrink tubing, cable ties)- Operating instructions Technical details: ·         fuel: diesel·         heat output: max. 1.8 kw, min. 0.8 kw·         air volume: max. 75 m³/h, min. 34 m³/h·         fuel consumption: max. 0.24 l/h, min. 0.1 l/h·         power drain: max. 29 W, min. 10 W·         manual start/stop→ On the Autoterm.cz website you will find a calculator for the correct dimensioning of the air heater The AUTOTERM Luft 2D (Planar 2D) is equipped with a height kit!This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents shooting of the combustion chamber when the atmospheric oxygen content drops. The max. Heating power drops in proportion to the amount of oxygen in the air. Roughly one can say: From 2.000 meters the loss of power per 500 m height is approx. 5%. Manufacturer tests up to 3.440 m were no problem. No difficulties are to be expected up to 4.000 m. The software itself calculates up to 5.000 m - however, this has not yet been tested in real height. The separately available control unit with timer (optional extra) features a larger OLED display and more intuitive operation. Temperature, ventilation and output can be configured via a display and various switches. An added timer clock allows you to set the heater to a specific time. OLED display provides maximum visibility with minimum power drain.  Possible settings:- temperature and output- time and date- language (English or Russian) Features of the new timer clock:- daily: one fixed time at which the heater starts each day- individual: up to thee different settings with different days and times. To heat your roof tent using your auxiliary heating system, we offer an installation service for a warm air duct through a ventilation plate. The improved new control unit is also available separately.  https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Precisely fitting base plate for parking heaters in Land Rover Defender 90, 110 & 130 Stainless steel mounting plate for auxiliary heating for all popular independent vehicle heaters (Webasto Airtop 2000 STC, Planar 2D12, Eberspächer) simply replaces the centre seat box cover underneath the cubby box of your Defender. All necessary cuttings to fit the heating unit and piping. The mounting plate fits all Land Rover Defender 90/110/130. Attachment with existing mounting material. Please note that you also need the Nakatanenga auxiliary heater console to fit an independent heating unit. The cubby box is fitted to this console. https://www.nakatanenga.de/media/pdf/74/df/0c/Merkblatt-Edelstahl-und-Rost.pdf  

Rotatable for individual airflow adjustment Rotating air vent, 60 mm, suitable for a variety of auxiliary vehicle heaters like e.g. Webasto, Eberspächer and Planar.This Webasto air vent also fits our auxiliary heater console.

Air vents for individual warm air regulation This vent can be used for all independent vehicle heaters with 60 mm piping, like the Planar 2D auxiliary heater. The vent can not be fitted to our auxiliary heater center console, in which case please use our Webasto vent.

Heater piping / flexible piping / air pipe for efficient distribution of heater air. The piping is specially tailored to suit the Planar 2D auxiliary vehicle heater, but also fits Webasto, Eberspächer and Truma heaters. Supplied according to stock, i.e. you can reveive either black or brown. colour: silver inner with either black or brown outerdiameter: Ø 60 mmprice per metre, only sold in full metre lenths 

Efficient airflow distribution T-piece suitable for warm air ducts of Planar 2D auxiliary heaters and other independent vehicle heaters with 60 mm hoses.

Dropside bushing 24mm for exhaust of AUTOTERM (=Planar) parking heater, with screw holes Side wall bushing for all Planar parking heaters with an exhaust pipe diameter of 24 mm (AUTOTERM Luft 2D / 4 D = Planar 2D, 4D, 44D).There is the version with screw holes as well as the version with stud bolts where no screws are visible from the outside. The variant with stud bolts is particularly suitable for a wall thickness of up to 15 mm.If the wall thickness is thicker, the version with screw holes should be used. Please note:When installing the parking heater, you must take into account the general wading depth of the vehicle. Depending on the position of the parking heater intake, the wading depth may change individually for the vehicle. Please also be sure to observe the instructions of the parking heater manufacturer!

Dropside bushing 25.4mm for the intake of the AUTOTERM (=Planar) parking heater Side panel bushing for all AUTOTERM parking heaters with an intake pipe diameter of 25.4mm (AUTOTERM Air 4D & AUTOTERM Air 2D).Please note:When installing the parking heater, you must observe the general wading depth of the vehicle. Depending on the placement of the parking heater intake, the wading depth may change individually for the vehicle. Please also be sure to observe the instructions of the parking heater manufacturer!

Additional tank 7.5 litres for parking heaters This additional tank can be placed anywhere on the vehicle.The tank can be filled with 7.5 litres of fuel, e.g. for the AUTOTERM Planar 2D parking heater. Suitable fastening material is included in the scope of delivery.

Complete set of AUTOTERM Air 2D parking heater for Defender The parking heater set AUTOTERM (Planar) 2D12 for the Land Rover Defender consists of all important components needed for the installation of a parking heater. Included in the delivery are the AUTOTERM 2D 12 Volt parking heater, our Nakatanenga parking heater console, the Nakatanenga mounting plate, a fuel tank extraction, a Webasto air outlet with 60 mm connection, 30 cm warm air pipe and a vibration damper.As a low-priced and powerful alternative to our Webasto parking heater kits, the AUTOTERM (=Planar) 2D parking heater is proving to be a real sales hit. This is partly due to the particularly compact dimensions, which allow installation even in small cars, vans, off-roader motorhomes, construction machinery, boats or in difficult installation situations. In the off-road / 4x4 sector, it is ideally suited for the "typical" off-road vehicles such as Land Rover Defender, Mercedes G or Jeep Wrangler JK.These are only a few of many reasons why we now offer the AUTOTERM (Planar) 2D 12 V parking heater in a clear and comprehensive complete set for the Land Rover Defender at an economical price. For both the Tdi/ Td5 and the Td4, we offer one set each with a perfectly matching accessory kit.You can select different front panel cut-outs for the parking heater console included in the scope of delivery. The associated connections are available in the classic cigarette lighter format (12 V) or as 5 V USB charging sockets for Apple iPhones, navigation devices, iPads and smartphones and are included in the scope of delivery.The parking heater can also be operated while driving.Running time: The AUTOTERM parking heater switches off automatically after 2 hours of operation. However, as soon as you press a button during operation, the parking heater continues to run indefinitely until it is switched off manually.Scope of delivery:- AUTOTERM 2D parking heater 12 volt incl. silencer, intake air hose, heat protection hose, tank intake pipe and corrugated exhaust pipe.- Optionally analogue control unit simple control (PU-5) with rotary control or digital control unit comfort control (PU-29) with time switch- Nakatanenga parking heater console incl. the selected connections- Nakatanenga mounting plate- Fuel filler cap- Webasto air outlet with 60 mm connection, rotatable- 30 cm warm air pipe (diameter: 60 mm)- Vibration damper- Fixing material (screws, nuts, clamps, shrink hose, cable ties)Technical data:- Fuel type: diesel- Heating capacity: max. 1.8 kW, min. 0.8 kW- Volume of heated air: max. 75 m³/h, min. 34 m³/h- Fuel consumption in operation: max. 0.24 l/h, min. 0.1 l/h- Power consumption in operation: max. 29 W, min. 10 W- Weight: 3 kg (independent heater)- Manual start/stop → On the Autoterm.cz site you will find a calculator for the correct dimensioning of the air heater,You can choose between two control elements:- Simple Control (PU-5) element with rotary control: The old PU-10 control element had a relatively inaccessible control surface. Therefore, the reliable control element with rotary control is now the new improved standard of the Planar parking heaters! With the rotary control, you can adjust the heating power of the parking heater and regulate the power of the ventilation in ventilation mode! The PU-5 control element with rotary control can also be purchased separately here.- The digital control element comfort control (PU-29) with timer has an OLED display and an understandable and clear interface.  Temperature, ventilation and power can be configured via the display and the various buttons. With the timer, you can easily set the start of the parking heater to a specific time. The digital control element with timer can also be purchased separately here.Setting options comfort control (PU-29):- Temperature and power (adjustable for the parking heater, the control panel and for an external heater).- Time and date - Operating language (English or Russian)Functions of the timer comfort control (PU-29):- Memory function: save the time so that the parking heater starts at this time every day - Configurable memory locations: Up to 3 different weekdays with different times can be set and saved. The AUTOTERM (=Planar) 2D12 is equipped with an altitude kit.This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heat output decreases proportionally to the amount of oxygen in the air. Roughly speaking, from 2,000 metres the loss of output per 500 m altitude is approx. 5%. Manufacturer tests up to 3,440 m were trouble-free. Up to 4,000 m no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not yet be tested at real altitude. Important:Especially when used at high altitude, the free travel of the fan is extremely important!Route the combustion air intake and exhaust extremely short and with low resistance - i.e. no kinks, no blockage or reduction. It should also be noted that operation beyond 3,000 m is still a technical compromise. Again, care should be taken to ensure that the combustion chamber is properly heated on a regular basis. The chamber must be burnt free of soot deposits. Soot deposits can also form on heaters that are permanently operated at the lowest setting. Therefore, the following still applies: No guarantee for sooty combustion chambers!In order to ensure the longevity of the heater, you should also free-burn it occasionally at low levels. The combustion chamber reaches full temperature after running at full load for about half an hour. Normally, no further maintenance is required. In case of extreme loads, e.g. during longer overnight stays at more than 4,000 m, the combustion chamber including the seal set should be cleaned if necessary. To heat your roof tent using your auxiliary heating system, we offer an installation service for a warm air duct through a ventilation plate. https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment