Votronic LCD Solar Computer
The following values are calculated and displayed under microprocessor control: - Current solar power 0 - 999 W (watt) - Current solar power 0 - 60.0 A (ampere) - The geographic and weather-dependent influences show up immediately and unmistakably. This also applies to the orientation of the sun, partial shading or soiling of the solar modules. - Current solar battery voltage 7 - 32.0 V (volts) Allows conclusions to be drawn about the battery status (flashing warning display at under or Overvoltage of the battery) - Invited solar capacity 0 - 9999 Ah (ampere hours) - Invited solar energy 0 - 9999 kWh (kilowatt hours) The energy generated by the solar modules (Wh and kWh) and that charged into the battery Capacity (Ah) are measured, added up and displayed, even over days and weeks. The display values can be individually reset to "zero" at any time for your own statistical purposes: Are the solar modules shaded or dirty or is something wrong? How much energy does my solar system actually deliver?In order to be able to answer these questions, VOTRONIC offers the LCD solar computer S, which is simply connected to the VOTRONIC solar charge controller of the SR and MPP series and immediately provides the required information. It is also possible to connect the LCD solar computer S to the controller at a later date, since the VOTRONIC solar charge controller already has are ready to plug in and provide the required signals. The connection is therefore kept extremely simple. The measured values are clear and easy to use at the push of a button for better control and use of the solar system shown on the display. The display is backlit (switchable) and also from greater distances and very easy to read under lighting conditions. The LCD solar computer S is designed as a panel version to match the VOTRONIC module system and is both optically and also mechanically (uniform height 85 mm) to the other display modules. Small front panel dimensions and the particularly small installation depth of just 22 mm allows installation at almost any point. If the device is not installed countersunk, stands a corresponding add-on housing is available in our range of accessories. The connection to the solar controller is ready to plug in with the supplied 5 m long connection cable, which can be extended by a further 5 m. Technical specifications: Nominal battery voltage (DC) in [V] 12 and 24 Current consumption max. in [mA] 3 - 30 LC display with specific segments Display function W, A, V, Ah, Wh Measuring range 20 - 990 Dimensions (WxHxD) in [mm] 80 x 85 x 25 Installation dimensions (WxHxD) in [mm] 66 x 72 x 22 Weight in [g] 55 Approval marks CE, E-approval (EMC / vehicle directive) Ambient conditions, humidity: max. 95% room humidity, non-condensing Scope of delivery: 5 m connection cable, fastening screws, operating instructions, drilling template
Prices incl. VAT;
Votronic Solar charge controller with 250 Wp or 430 Wp module output
MPP Solar-Regler Please note that the solar charge controller can only be used with solar panels up to the maximum power rating (Wp) and below the maximum allowable voltage (Voc) may be used. The controller is not intended for an input-side connection (+/- solar panels) of wind, water, fuel or motor generators, power supplies, batteries or other power sources. The MPP solar controller for high-quality motorhomes, caravans and boats. Votronic solar controllers of the "MPP" series (Maximum Power Point) with “IU1oU2” charging characteristics are connected as a link between the solar panel (s) and the battery (s). With MPP technology, the controller automatically determines the maximum power output (MPP) several times per second the solar modules. The excess voltage of the solar module is transformed to a higher charging current for the battery, (realized by high-frequency switching regulator technology with high efficiency). The gain in charging current is used for shorter Charging times taken care of and for the best possible use of the solar system. The MPP solar controllers work fully automatically, are maintenance-free and offer the following functions: MPP charging current increase compared to conventional controllers through the use of the latest controller technology (microprocessor) by 10% to 30% (efficiency> 95%). The performance plus is particularly evident in the cooler seasons and z. B. in high fog, lower and diffuse lighting (overwintering). For charging lead-gel, lead-AGM, lead-acid batteries or LiFePO4 complete batteries (with integrated BMS, Balancing, safety circuit and approval!) Of the specified nominal voltages and the additional supply of an Consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs. The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is impossible. Two battery charging outputs: Automatic charging of the main supply board battery (BORD I) as well as support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging. Monitoring-free charging: standard protection against overload, overheating, polarity reversal and battery back-discharge (with insufficient solar power z. B. twilight, at night etc.). Parallel / buffer operation: compliance with the charging regulations even when consumers are operating at the same time. Overcharge protection: regulates the charging current of the battery when there is too much solar power and the battery is full, ensures Power consumption through immediate recharging for the highest possible battery charge. "IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid layers (lead) and ensures equalization charging of the individual battery cells (lead and lith.), then automatic maintenance charging (U2). Charging cable compensation: voltage losses on the charging cables are automatically compensated. On-board network filter: problem-free parallel operation with wind and motor generators, network chargers, alternators, etc. Measurement output for EBL, possibly existing electroblock in the living area of the vehicle: Enables the convenient use of a (Solar) power display built into the electroblock to control the solar system. Please check in advance the compatibility of your Schaudt electroblock (EBL) and the corresponding control and scoreboard, as we cannot guarantee this. Switching output "AES" (only MPP 250, MPP 350 and MPP 430): causes permanent abundant solar The automatic switching of refrigerators with "AES" (Automatic Energy Selector, Electrolux / Dometic) from gas to 12 V operation. Connection for battery temperature sensor (item no. 2001): With lead batteries, the adjustment takes place automatically the charging voltage to the battery temperature, causes a better full charge of the weaker battery in the cold, In summer temperatures, unnecessary battery gassing and stress is avoided. LiFePO4 batteries: battery protection at high and especially at low temperatures. If the battery temperature can drop below 0 ° C during operation. Ready to plug in for the connection of the Votronic solar display devices LCD-Solar Computer S for optimal control of the system. Technical data CHARGE REGLER-MPP250: Nominal battery voltage (AC) in [V] 12Solar module output max. [Wp] 250Solar module current max. [A] 15.0Solar module voltage max. [V] 50Charging current batt. I / II max. [A] Load programs: 1 "Gel": charging program for gel batteries, characteristic curve IU1oU2Matched to closed, gas-tight gel / dryfit batteries with fixed electrolyte, which generally require a higher charging voltage level and longer U1 holding times in order to achieve short charging times with particularly high capacity storage and to avoid long-term battery "starvation".2 "AGM": Charging program for AGM / fleece batteries, characteristic curve IU1oU2Designed for charging closed, gas-tight AGM (Absorbent-Glass-Mat) batteries in lead-fleece technology, which require a particularly high U1 level with coordinated holding times for full charge and then a moderate U2 level to maintain charge (Plate and round cell technology).4 "UNIVERSAL": Charging program for lead-acid / wet / AGM batteries, characteristic curve IU1oU2Universal program for charging and maintaining the charge of acid batteries in vehicles (mixed mobile / stationary). With a medium U1 level, it still offers short charging times, a good charge factor and good acid mixing for open and closed, low-maintenance, maintenance-free standard, drive, lighting, solar and heavy-duty batteries, as well as AGM batteries with a normal U1 level.Li "LiFePO4": Charging program for lithium batteries, characteristic IU1oU2Charging program tailored to lithium LiFePO4 batteries with their own BMS and prescribed or built-in protective circuit.
Prices incl. VAT;
Nakatanenga installation panel
Installation panel - easy installation for 12V sockets, USB chargers or voltmeters This practical installation panel enables the neat and tidy integration of built-in devices such as 12V sockets, USB charging sockets or voltage displays (voltmeters) in vehicles, boats, motorhomes or other applications. The cover ensures a tidy appearance and makes installation considerably easier.Depending on your requirements, the cover is available in different versions - suitable for one, two or three devices. This means you can put together your own customised configuration with complete flexibility.Installation is quick and easy - ideal for retrofitting or conversions.Note: The devices and consoles shown are for illustrative purposes only and are not included in the scope of delivery.
Prices incl. VAT;
Switch box / switch system, Terrafirma with 8 switches
Terrafirma Multi-function 8-way switch panel system If you are looking to fit LED lights to your vehicle but are put off with all the wiring? This 8-way switch panel allows you to wire up eight different lights or accessories while only having one switch panel mounted in the cab of the vehicle. No more drilling lots of holes with separate switches and relays. Simply connect your lights to the main fused control board and run one control wire through to the cab area. This then allows you to control all eight devices separately. A Sheet with 50 switch symbol stickers is also included so you can customise your touch screen panel to match your lights. Product information: Maximum Power - 600 w - 1200 w Maximum Current - 60 A Input 12 v to 24 v Outlets - 2 x 30 amp, 2 x 20 amp, 2 x 10 amp and 2 x 5 amp IP67 rated What's included: Touch Screen Panel (115 mm x 66 mm x 15 mm) Circuit Control Box (162 mm x 110 mm x 34 mm) Fuses Switch Panel Brackets Voltage Protection Breaker Circuit Box Brackets Sheet with 50 switch symbol stickers Battery Cables & Wire harness Screws & Mounting Hardware
Prices incl. VAT;
Montagepauschale für Nakatanenga Doppelbatteriesystem 160Ah
Einbau zum Fixpreis – Nakatanenga 160 Ah Doppelbatteriesystem für Land Rover Defender Pauschale für die Installation des Nakatanenga Doppelbatteriesystem 160 Ah für den Land Rover Defender in unserer Werkstatt. Der Einbau erfolgt zum angegebenen Fixpreis, unabhängig von der Dauer. Der Preis beinhaltet eine kurze Einweisung des Kunden. Bitte beachten Sie: Der hier genannte Preis bezieht sich nur auf die Montagepauschale, die zu montierende Ware ist separat zu erwerben. Die Montagepauschale bezieht sich auf eine seriennahe Montagesituation. Sollte hier durch technische Gegebenheiten oder spezielle Kundenwünsche ein besonderer Montageaufwand entstehen, greift die Pauschale nicht, es wird nach Aufwand abgerechnet - dies können wir jedoch erst dann entscheiden, wenn das Fahrzeug in unserer Werkstatt steht. Bitte geben Sie bei der Bestellung Ihre Telefonnummer für die notwendige Terminabsprache mit an. Die Montage ist nur vor Ort in Berg bei Neumarkt (Postleitzahl: 92348) möglich.
Prices incl. VAT;
Portable Powerstation with LiFePo or AGM battery, with multiple out outlets
Battery box with various connections, with solar panel Optionally with AGM or LiFePo battery In the 21st Century modern technology is everywhere, even off-road and off the grid, but more often than not there is no power when you're out and about on some trail in some country. One option is the classic cigarret-lighter as a power source, but in using this frequently you risk decharging your battery to a point where it won't start your car anymore. Another option would be a generator, but those are loud, impractical and noisy. To solve this probem highly portable powerbanks were invented, but for a multiple day long trip a small powerbank just won't cut it. So, what if you had a lagre but portable power bank? One you could simply charge, even off the grid, maybe with a solar panel? And one that is heavy dut enough to endure week long trips and years of use ? Hold on, that's exactly what we did! This compact, but long-lasting Powerstation (33Ah) offers a cigaret lighter-output and two USB-ports (5V - 2.1A), in a roubust shell. It can simply be charged using our solar panels by Optimate. LiFePo4 batteries – with their lithium iron phosphate cathode material – are perfect for running your camping or work utilities on the road, especially in conjunction with our mobile battery boxes. Unlike your conventional AGM lead-acid technology, the lithium battery combines vastly superior charging/discharging qualities with extremely low weight and small volume, respectively, and a long service life. LiFePo4 batteries tolerate deep discharging without problems, unlike AGM batteries which will suffer irreparable damage when repeatedly discharged beyond 50%. Unless you require the greater tolerance for extreme cold in AGM’s, you should definitely consider the higher initial costs of LiFePo4 batteries and compatible chargers. Enormous weight and space reductions, the long life-cycle and the hassle-free charging and discharging of the battery are strong arguments for the investment. And last but not least: LiFePo4-technology is extremely safe. robust shell portable design comfortable handle 20 A car-fuse 33 Ah (396Wh) AGM brand battery optionally 35 Ah LiFePo battery 2x USB-plug (out) 1x cigaret-lighter (out) 1x SAE junction box for charger (charger not included) (in) 1x On-/Off-switch simply plug in and off you go Scope of delivery: 1 x Optimate solar panels in a choice of 40, 60 and 80 watts, including bag and stand.1 x Optimate charge/monitor controller, including weatherproof battery cable1 x Nakatanenga battery box selectable in 4 colours, with different connections Please note the legal information on batteries HERE. For certain types of batteries, we are legally obliged to charge a deposit.
Prices incl. VAT;
Central electrics TEXU400 - Fuse holder, busbars
TEXU400 central electrics for touring vehicles and boats The TEXU400 revolutionises electrical installation. It combines various components that previously had to be purchased individually in a round housing that optimises the use of space and the number of possible connections in the smallest possible space. The special arrangement, which is ONLY available in the TEXU400, enables system integration with groundbreakingly low effort. This results in drastic savings in costs as well as time and space, while at the same time reducing sources of error and providing the highest level of application comfort after installation. It also requires considerably less installation space in a touring vehicle or boat. Extensive electrical systems can thus be planned in a smaller space and the space gained can be used for other purposes. Connection of up to 4 battery banks 11 high-current and 4 standard consumers Plus rail for on-board batteries and consumers Screw terminals and fuses 2x MEGA / AMG fuse max. 400 A 9x MIDI / AMI fuse max. 170 A 4x ATO / ATC / ATP fuse max. 30 A 1:1 ground distributionPut an end to insufficient ground distributions! With the TEXU400, a negative connection is also provided for each positive connection. Simple integration of a summation current measurementThe factory-fitted Sunt bridge between the negative busbars can be easily removed by means of screws and replaced by a plastic bar included in the scope of delivery to enable quick and uncomplicated integration of a measuring shunt. MEGA fuse with double inputWhere cable lugs used to be stacked or other suboptimal constructions had to be devised on a case-by-case basis (e.g. in the case of split cables of powerful inverters), there is now a professional solution: a MEGA fuse point with max. 400 A and double screw connection, ensures professional and safe installation of such components. Ignition-protected according to ISO 8846The UFO is ignition-protected according to ISO 8846 with the integrated, all-round bar with seal. It is therefore also approved for installation in the engine compartment. LED failure check with fibre optics Immediate diagnosis. Fibre-optic cables light up the LED failure check directly at the inscription of the circuits in the closed cover. You can save yourself the trouble of removing fuses and searching upside down for faults in confined spaces! A prefabricated labelling set with partly customisable content is included in the scope of delivery of the TEXU400. Space for spare fusesThe TEXU400 contains additional slots for spare fuses (1x MEGA, 2x MIDI, 2x ATO/ATC/ATP)Convenient opening and closingThe knob centrally located on the enclosure cover makes it easy to open and close the cover and even allows one-handed operation in confined spaces. Please note: As individual electrical installations contain different components that must be suitably fused, a prefabricated fuse set is NOT included directly in the scope of delivery of the TEXU400.
Prices incl. VAT;
Votronic Charging converter by Votronic
Charging converter High charging capacity even on short journeys or full charge on longer journeys. The voltage is brought to the required level (increased or decreased) in order to be able to precisely charge the on-board battery with the optimal charging characteristic. Compensates for line losses and voltage fluctuations in the alternator, such as occur continuously to a considerable extent in Euro 6 vehicles (intelligent alternators). Compact design, low weight (high-frequency switch mode technology) and powerfully dimensioned power components for safe operation. A significantly better energy balance of the on-board battery without intervention in the starting circuit If the 12 V consumers are supplied, they are protected against overvoltage and voltage fluctuations. Overcharging of the battery is impossible because the charging voltage is regulated in such a way that it is free of peaks Fully automatic operation: the device is constantly connected to the batteries and is automatically activated by the running alternator of the vehicle. The batteries are not discharged when the engine is not running. Parallel and buffer operation: If the battery is used at the same time, it continues to be charged or is kept full. The device automatically calculates and monitors the adjustment of the charging times. Monitoring-free charging: Multiple protection against overload, overheating, overvoltage, short circuit, malfunction and back-discharge of the battery through electronic regulation up to complete separation of device and battery. Built-in on-board network filter: Problem-free parallel operation with other charging sources (EBL, chargers, motor and fuel generators, solar systems) on one battery. Charging cable compensation: voltage losses on the charging cables are automatically compensated. Connection for battery temperature sensor (included in delivery): In the case of lead batteries (acid, gel, AGM), the charging voltage is automatically adjusted to the battery temperature, results in better full charging of the weaker battery in the cold, and in summer temperatures unnecessary battery gassing avoided. LiFePO4 batteries: battery protection at high and especially at low temperatures <0 ° C. Charging aid for deeply discharged lead batteries: Gentle pre-charging of the (lead-acid, gel, AGM) battery up to 8 V, then powerful support for the battery if consumers are still switched on. Technical specificationsInput from vehicle starter battery "+ IN Start"Vehicle starter battery nominal voltage 12 V.Battery capacity (size), recommended at least 50 AhInput voltage range (EURO 6 +), D + controlled 10.5 - 16.5 V.Input overvoltage shutdown (EURO 6 +), max. 16.5VPower consumption max. 490 WCurrent consumption (at lowest input voltage) max. 0.05 A - 39 AActivation control input "D +", from D +, terminal 15, ignition 8 - 17 V.Charge output on board supply battery "+ OUT board"Charge / buffer / load current, regulated IU1oU2, lead, LiFePO 0 A - 30 A (0 A - 20 A *)Lead-acid, gel, AGM battery nominal voltage 12 V.Capacity (battery size), recommended / up to 60-200 / 260 AhLead loading programs stored in the memory 3Precharge current (deeply discharged battery <8V), max. 15 A (10 A *)Safety charging voltage in the event of battery overtemperature 12.80 V.LiFePO4 battery nominal voltage 12 V (12.8 -13.3 V)Capacity (battery size), recommended / up to 60-200 / 260 AhLiFePO4 charging programs stored in the memory 4Safety charging voltage in the event of battery overtemperature 12.80 V.Recharging branch, charging / charge retention for the 12 V START batteryfrom the BOARD battery (e.g. when charging the BOARD battery from the mains) 12 V / 0-1 AActive with lead acid, gel, AGM BORD battery voltage On:> 13.1 V, Off: <13.0 VActive with LiFePO4-BOARD battery voltage on:> 13.5 V, off: <13.4 V"T T" input for battery temperature sensor "board" yesEBL START In, EVS measurement input: yesQuiescent current, StandBy 3 ... 7 mATriple charging timerVoltage ripple <30 mV rmsCharging voltage limit "+ OUT board" (consumer protection) 15.00 VExternal overvoltage shutdown "+ OUT board" (20 sec) 15.50 VShort circuit / back discharge / S. Loaders 1 "Gel": charging program for gel batteries, characteristic curve IU1oU2Matched to closed, gas-tight gel / dryfit batteries with fixed electrolyte, which generally require a higher charging voltage level and longer U1 holding times in order to achieve short charging times with particularly high capacity storage and to avoid long-term battery "starvation".2 "AGM": Charging program for AGM / fleece batteries, characteristic curve IU1oU2Designed for charging closed, gas-tight AGM (Absorbent-Glass-Mat) batteries in lead-fleece technology, which require a particularly high U1 level with coordinated holding times for full charge and then a moderate U2 level to maintain charge (Plate and round cell technology).4 "UNIVERSAL": Charging program for lead-acid / wet / AGM batteries, characteristic curve IU1oU2Universal program for charging and maintaining the charge of acid batteries in vehicles (mixed mobile / stationary). With a medium U1 level, it still offers short charging times, a good charge factor and good acid mixing for open and closed, low-maintenance, maintenance-free standard, drive, lighting, solar and heavy-duty batteries, as well as AGM batteries with a normal U1 level.Li "LiFePO4": Charging program for lithium batteries, characteristic IU1oU2Charging program tailored to lithium LiFePO4 batteries with their own BMS and prescribed or built-in protective circuit.
Prices incl. VAT;
BlueSea MIDI strip fuse 150A
Blue Sea BS 5258 AMI/MIDI fuse 150A Is ideal for electronic equipment where superfast fuses are required. Main features: Superfast fuses ideal for electronic equipment. Classic circuit breakers for automotive and truck fuse protection Tin-plated connectors for corrosion resistance Visible indication of a blown fuse Packaging unit of 2 pieces Technical data: Maximum current consumption: 150A Maximum voltage: 32V DC Breaking capacity: 5000A @ 16V DC 2000A @ 32V DC Battery connection bolt with torque limitation: 4.52 Nm Minimum temperature: -40 °C maximum temperature: 125 °C Material: tin-plated copper CDA 110/UNS11000 MIDI strip fuse 100 A, 2 pieces, e.g. for fuse holder NABS7720, but also for other holders with MIDI sockets. With 125 A, the fuses are ideally suited for protecting our TEXU400 central electrics, which may be loaded with max. 400 A. Suitable for applications up to max. 32 V. Scope of delivery: 2 pieces
Prices incl. VAT;
MIDI strip fuse 100 A
Blue Sea BS 5256 AMI/MIDI fuse 100A Is ideal for electronic equipment where superfast fuses are required. Main features: Superfast fuses ideal for electronic equipment. Classic miniature circuit breakers for automotive and truck fuse protection Tin-plated connectors for corrosion resistance Visible indication of a blown fuse Packaging unit of 2 pieces Technical data: Maximum current consumption: 100A Maximum voltage: 32V DC Breaking capacity: 5000A @ 16V DC 2000A @ 32V DC Battery connection bolt with torque limitation: 4.52 Nm Minimum temperature: -40 °C maximum temperature: 125 °C Material: tin-plated copper CDA 110/UNS11000 MIDI strip fuse 100 A, 2 pieces, e.g. for fuse holder NABS7720, but also for other holders with MIDI sockets. With 125 A, the fuses are ideally suited for protecting our TEXU400 central electrics, which may be loaded with max. 400 A. Suitable for applications up to max. 32 V. Scope of delivery: 2 pieces
Prices incl. VAT;
OPTIMATE PRO-1 DUO Battery Charger TM650
PRO series: 12V 10 A diagnostic battery charger tester & power supply unit. Suitable for new or used 12 V lead acid (3-50 Ah) and 12.8 V/13.2 V LiFePO4 (2-20 Ah) batteries. 3 choices: Select a charging mode for 12 V lead-acid OR 12.8 V LiFePO4 or select the power supply mode for battery support during vehicle diagnostics, tuning or troubleshooting.Automatic quick battery activation: a flashing green test light indicates that the battery is healthy and sufficiently charged.Intelligent recovery mode for deeply discharged batteries; a bad battery is quickly identified, a good battery is charged and then retested.Push button activated BMS recovery for LiFePO4 batteries.Test battery indicator for GOOD (80 to 100 %), OK (60 to 80 %) and BAD (below 60 %).Power supply mode provides constant power for vehicle tuning, diagnostics and troubleshooting. CHARGING CURRENT: 0.4 A to 10 A variable (Ampmatic). CHARGING VOLTAGE: 12 V lead acid: 0.5 V to 22 V. 12.8 V/13.2 V Lithium LFP (LiFePO4): 0.5 V to 14.4 V. Power supply: 11 V to 13.6 V. OPERATION: Selectable USE: Indoor IP40 rating. INPUT: Global (100-240 V 50-60 Hz), high efficiency. STYLE: Case with rubber bumper, with wall bracket or suspension rod. Class 2 AC input socket, with ON/OFF switch, 15 cm/6″ output cable. CABLES INCLUDED: Class II power cord, suitable for the region, O-43 charging cable extension 180 cm/72″ and O-14 fused battery clips. CARRYABLE USE: Hanging hook for vehicle and wall receiver included. WARRANTY: 2 year limited repair/replacement warranty. By the manufacturer!
Prices incl. VAT;
Battery box with various connections, AGM or LiFePo battery
Battery box with various connections, AGM or LiFePo battery In the 21st Century modern technology is everywhere, even off-road and off the grid, but more often than not there is no power when you're out and about on some trail in some country.One option is the classic cigarret-lighter as a power source, but in using this frequently you risk decharging your battery to a point where it won't start your car anymore. Another option would be a generator, but those are loud, impractical and noisy. To solve this probem highly portable powerbanks were invented, but for a multiple day long trip a small powerbank just won't cut it.So, what if you had a lagre but portable power bank? One you could simply charge, even off the grid, maybe with a solar panel? And one that is heavy dut enough to endure week long trips and years of use ? Hold on, that's exactly what we did! This compact, but long-lasting Powerstation (33Ah / 35Ah) offers a cigaret lighter-output and two USB-ports (Typ A: QC3.0-Port - Typ C: QC4.0-Port, in a roubust shell. It can simply be charged using our solar panels by Optimate.LiFePo4 batteries – with their lithium iron phosphate cathode material – are perfect for running your camping or work utilities on the road, especially in conjunction with our mobile battery boxes. Unlike your conventional AGM lead-acid technology, the lithium battery combines vastly superior charging/discharging qualities with extremely low weight and small volume, respectively, and a long service life. LiFePo4 batteries tolerate deep discharging without problems, unlike AGM batteries which will suffer irreparable damage when repeatedly discharged beyond 50%. Unless you require the greater tolerance for extreme cold in AGM’s, you should definitely consider the higher initial costs of LiFePo4 batteries and compatible chargers. Enormous weight and space reductions, the long life-cycle and the hassle-free charging and discharging of the battery are strong arguments for the investment. And last but not least: LiFePo4-technology is extremely safe. • robust shell• portable design• comfortable handle• 33 Ah (396Wh) AGM brand battery / 35 Ah LiFePo battery• 20 A car-fuse• 2x USB-plug (Typ A: QC3.0-Port - Typ C: QC4.0-Port)• 1x cigaret-lighter (out)• 1x SAE junction box for charger (charger not included) (in)• 1x On-/Off-switch • simply plug in and off you go Please note the legal information on batteries HERE. For certain types of batteries, we are legally obliged to charge a deposit.
Prices incl. VAT;
Outdoor socket outlet 2-pole
Compact, robust, versatile 2-pin socket outlet 6-42 V, 16 A This 2-pin socket outlet is ideal for use in low-voltage systems from 6 to 42 volts - whether in vehicle construction, agricultural machinery, trailers or workshop applications. With a load capacity of up to 16 amps, it is reliable and versatile. Whether as a spare part or for individual conversions: This socket offers a safe, long-lasting connection for many applications in vehicles and beyond. 2-pin plug connectionIn a robust aluminum housingSuitable for outdoor applications6-42 V, max. 16 AComplies with DIN 14690
Prices incl. VAT;
Heater resistor for Land Rover Series III and Triumph GT6 TR4 TR6
Heater Engine Resistor OEM Land Rover Series III Triumph GT6 TR4 TR6Reference number 7H6926.
Prices incl. VAT;
Votronic Bluetooth connector with Energy Monitor app
Product description The Monitor consist of a special Bluetooth connector (S-BC), which delivers, in combination with the Votronic solar charger (MY2013) with the LCD solar computer S, or with the smart Shunt with the LCD battery computer S or the VPC Jupiter, all the information from your monitor to your phone. The corresponding app for Android and IOS is available in both stores. Connecting the Bluetooth module S-BC is incredibly easy. Simply use the included cable to install it between Votronic solar charger and LCD solar computer S or between Smart Shut and the LCD battery computer s / VPC Jupiter. The device has two in- and out-puts, this way you can connect 1 solar charger with LCD solar computer and 1 Smart Shunt with LCD battery computer or VPC Jupiter simultaneously. This way you get all the information on charging, voltage, solar-status, etc. right on your phone without any trouble. Additionally, the app saves the most important data and displays it in the app for extended periods of time. You can even export these files for analysis purposes. This Bluetooth module can just as well be installed after the fact, so whenever you are ready! Technical specifications: Typ Bluetooth Connector S-BC Measuments (WxLxH) in [mm] 75 x 47 x 24 Weight in [g] 37 Certifications CE, E-Prüfung (EMV/Kfz-Richtlinie) Surroundings: Humidity: max. 95% Scope of delivery: Manual, 2x Cable 6-point connector 1 m long The Bluetooth-Connector S-BC is compatible with the following devices: VOTRONIC Solar-charger in SR- and MPP-technology from 2014 (serial number 14Vxx.xxxxx) Battery Charger, Typ VBCS-Triple LCD battery computer S with Smart-Shunt VPC Jupiter with Smart-Shunt Energy Monitor App via Bluetooth-Connector S-BC Compatible with LCD-Batterie-Computer S and VPC Jupiter with Smart-Shunt Compatible with Votronic Solar-charger(SR and MPP) from 2014 with LCD-Solar-Computer S Solar- and battery-Information thanks to a shared module (Dual-Mode) Plug & Play Upgrade any time Compact form-factor and minimal energy consumption Connection via Bluetooth 4.0 (2,4 GHz) Range up to 50 m Free App (Android and IOS) Export CSV.files for analysis Android from Android 5.0IOS from iOS 10: iPhone ( 5) or iPad (3. Generation)
Prices incl. VAT;
Electical Cable, 5-pole, 2.5 mm², sturdy rubber sheathing, with protective conductor, flexible
5-pole electric cable 5-pole electrical cable, 2.5mm², sturdy rubber sheathing, with protective conductor, flexible, black, price per metre. High-quality - manufacturer: LAPP Kabel Please order multiple items of this article for the desired lengh in metres - e.g. if you require five metres altogether you order this item five times.
Prices incl. VAT;
BlueSea fuse holder with cover, for 8 flat fuses
BlueSea fuse holder with cover, for 8 flat fuses The fuse holder with cover accommodates 8 fuses in a compact space and serves as a power distributor for setting up up to 8 circuits. Commercially available ATC flat fuses can be used.It is suitable for 12 V and 2 4 V vehicle electric systems and may be loaded with up to 30 A per circuit and 100 A in total at the same time.Delivery without further accessories, if shown, these are for illustration purposes only.
Prices incl. VAT;
VOX microphone 6-pin
Albrecht CB radio VOX microphones offer the perfect solution for hands-free communication in vehicles in accordance with Section 23 (1a) of the Road Traffic Act, which prohibits the use of microphones by hand in vehicles from July 1st, 2020. These microphones can be used with almost all CB radios on the market. The integrated active noise cancellation function filters out disruptive background noise and offers very clear voice transmission. The integrated battery has an operating time of approx. 60 hours and can also be charged while the microphone is in use. Properties:► for hands-free communication in the vehicle (compliant with § 23 (1a) StVO, which prohibits the use of microphones by hand in vehicles from July 1st, 2020)► Active Noise Cancellation filters out disturbing background noise► VOX sensitivity adjustable in 4 levels► VOX delay adjustable in 4 levels► Impedance: 4.7K ohms► Sensitivity: -58db► Up / Down buttons► integrated battery 3,000 mAh (rechargeable)► Operating time: approx. 60 hours► Can be used while charging► Micro-USB charging socket on the microphone► Connection: 6-pin CB radio plug
Prices incl. VAT;
External GPS antenna for GeoSafe alarm and tracking tracker
External GPS antenna for GeoSafe alarm and tracking tracker The external antenna improves the GPS reception of the GeoSafe alarm and tracking tracker. The antenna has a magnetic base that allows it to rest or hang on metal surfaces without slipping.Technical data:Frequency: 1575.42 MHZVoltage: 3,0 - 5,0 VoltCable length: 5 metres
Prices incl. VAT;
Copper cable H07RN-F, extended version, 35mm², 1 metre
Copper cable H07RN-F, extended version, 35mm², 1 metre High-quality copper cable, 35 mm², e.g. for jump-start or winch cable, price per metre. Order this article as often as you need 1 m length.Manufacturer information:H07RN-F, extended version are heavy rubber hose cables for connecting heavy duty equipment and for connecting commercial and agricultural machinery where the cables are subject to medium mechanical stresses. (e.g. machine tools, hot plates, hand lamps, power tools) Suitable for use in dry, damp or wet rooms as well as outdoors in accordance with the intended use as per DIN EN 50565-2 (VDE 0298-565-2). Fixed installation e.g. on plaster in temporary buildings and residential barracks is permissible. Continuous, operational movements, forced guidance or use on cable drums or rollers or under tensile load with a conductor cross-section of more than 15 N/mm² are not permitted. Arrangements of single-core rubber-sheathed cables H07RN-F can be used for short-circuit and earth-fault protected installations according to VDE 0100-520 (VDE 0100-520).Extended fields of application due to additional properties: Halogen-free materials with low smoke density in case of fire: Improved suitability for enclosed places with increased concentration of persons and material assets. Improved cold flexibility: Minimum conductor temperature of -40 °C in moving applications Wider temperature range: Maximum conductor temperature of +90°C instead of +60°C Standardised ozone resistance and wider temperature range: generally higher resistance outdoors Uninterrupted long-term immersion (AD8) up to 100 m water depth (no drinking water, minimum water temperature of +5°C, no chlorine water, only largely stagnant water without current) Drip-loop torsion resistance: As a torsion cable in the drip loop ("cable loop") of wind turbines between nacelle and tower.
Prices incl. VAT;
Adapter for connecting 2 Alan PL259/6 plugs
Adapter for Connecting Two Alan PL259/6 Connectors This adapter allows easy and secure connection of two Alan PL259/6 connectors. Ideal for use in radio communications, antenna installations, or for extending coaxial cables.Made from durable materials to ensure reliable signal transmission and long-lasting performance. Features: Compatible with Alan PL259/6 connectors Compact design Easy to use Perfect for radio and antenna applications
Prices incl. VAT;
ARMYTEK C4 universal charger
Product description Uni C4 Plug Type C Universalladegerät If you are familiar with the Armytek flashlights Tiara, Wizard and Prime, you know that the Canadians are always trying to get the most out of different battery types for maximum performance. The technology concerning battery and charge management is second to none whether it’s battery recognition, charge level monitoring, temperature control or the prevention of current drain when the lamp is switched off. No wonder Armytek is packing everything that’s intelligent and user-friendly into their universal charger Uni C4 with its Type C plug and car adapter. The four charging slots support any combination of Li-Ion, Ni-MH, Ni-Cd, LiFePO4 and Ni-Zn batteries and automatically provide the optimal current of up to 2 A for every battery type and charge level. Even fully drained batteries are recognized and recharged with gentle 0.1 A. Among the Uni C4’s safety features are the detection of bad rechargeables, disposable batteries or reverse polarity. Multi-colored LED’s with an extra night mode indicate charging status and levels and, as always with Armytek, a reassuring 5 years no-hassle warranty proves their confidence in the product’s quality. Supports IMR/Li-Ion, Ni-MH, Ni-Cd, LiFePO4 and Ni-Zn batteries Quick charge with up to 2 A current Easy selection of battery type and charge current with one button per each channel Multicolor LED indication with Night mode and useful 5 LEDs per channel Over-discharged and sleeping battery activation function with safe 0.1 A current Saving of actual battery type to restore after electricity interruption Auto-detection of bad batteries, reverse polarity and primary batteries Capability of hand settings for safe current and type of battery, which is found as bad 5 years no hassle warranty Technical specifications: Plug type: Plug type C Technical details of chargers Number of channels: 4 Battery type: IMR/Li-Ion, Ni-MH, Ni-Cd, LiFePO4, Ni-Zn Battery compatibility: diameter 8..32 mm and length 30..70 mm (10440, 14500, 16340, 18350, 18650, 26650, 32650, AAAA, AAA, AA, C, D) Voltage per channel: 4.2 V / 3.65 V / 1.9 V / 1.5 V Charging current per one channel: 2 A / 1 A / 0.5 A / 0.1 A Input: AC 85-264 V / 0.5 A (50/60 Hz) or DC 9-14 V / 1 A Indication type: 4х5 multicolor LEDs Weight: 271 g What's included: Car adapter, power cord, manual
Prices incl. VAT;
OBD Bluetooth Diagnostics
OBD Bluetooth Diagnostic Device OBD diagnostic device from GAP Diagnostic, for displaying and clearing error messages as well as controlling numerous functions, with very simple installation (plug into the ODB port), operation via the menu of the vehicle or a free iOS/Android app.The diagnostic device is suitable for the following vehicles: Land Rover Defender L316 2007-15 Land Rover Discovery 3/LR3 L319 2004-09 Land Rover Discovery 4/LR4 L319 from 2010 onwards Land Rover Freelander 2/LR2 L359 Range Rover Evoque L538 from 2011 Range Rover L322 2002-05 Range Rover L322 2006-09 Range Rover L322 2010-12 Range Rover L405 from 2013 Range Rover Sport L320 2005-09 Range Rover Sport L320 2010-13 Range Rover Sport L494 2014 onwardsEven more features and statistics can be accessed via the free app. This requires one of the following devices: Apple iPad Mini or newer Apple iPad 3 or newer Apple iPhone 4S or newer Apple iPod Touch 5 or newer Android devices with Bluetooth 4.0 receiver (Attention! Experience shows that particularly inexpensive devices usually do not work!)
Prices incl. VAT;
ON/OFF switch with control light
ON/OFF switch with pilot light in round recessed housing ON/OFF switch with red control light in round installation housing.The switch can also be easily exchanged for our rocker switches with location lighting or other rocker switches in this format.Load capacity: 12V 10A / 24V 6AHole diameter bore: 29mm
Prices incl. VAT;
Outdoor plug 2-pole
2-pole plug connection to DIN 14690 - Robust, reliable, versatile This high-quality 2-pole plug connection in a robust aluminum housing is specially designed for demanding applications in the low-voltage range (6-42 V). With a load capacity of up to 16 amps and the standardized design in accordance with DIN 14690, it offers a secure and durable connection - even under harsh operating conditions. This plug connection is the first choice for anyone looking for a durable, standard-compliant solution for mobile power supplies and device connections. 2-pin plug connectionin a robust aluminum housingSuitable for outdoor applications6-42 V, max. 16 AComplies with DIN 14690
Prices incl. VAT;