Current %
Premium Long-Term Underbody and Cavity Corrosion Protection with Mike Sanders and TimeMAX for INEOS Grenadier Long-lasting corrosion protection for your INEOS Grenadier: Using Mike Sanders Corrosion Protection Grease, TimeMAX underbody protection and supplementary Normfest Protector Wax, our workshop team draws on 30 years of experience to support the long-term protection of your off-road vehicle – both inside and out. At our specialist 4x4 workshop in Berg bei Neumarkt, Bavaria, between Nuremberg and Regensburg, we offer professional underbody and cavity corrosion protection for the INEOS Grenadier. This allows you to supplement your Grenadier's existing corrosion protection, protect heavily exposed areas of the ladder chassis, underbody and bodywork, and help prevent expensive rust damage over the long term. The following services are included in the complete package: Comprehensive corrosion protection: Additional treatment of accessible areas of the ladder chassis inside and out, underbody, wheel arches, axles, doors, rear doors and bonnet. Professional preparation: Removal of relevant covers and trim panels and assessment of existing corrosion protection. Extensive protective masking: Careful masking of bodywork, painted surfaces, windows, brakes and other components that must not be treated. Mike Sanders cavity protection: Additional long-term protection using heated, creeping corrosion protection grease and specialist cavity probes in suitable cavities. TimeMAX underbody protection: Durable protective coating for suitable external underbody surfaces. Normfest Protector Wax: Supplementary corrosion protection in selected areas. Endoscopic inspection: Visual inspection of accessible cavities before and after treatment. Reassembly and cleaning: Reinstallation of removed components and final cleaning. A detailed explanation of each stage of the treatment can be found below. Your benefits – and what they mean for your INEOS Grenadier Additional long-term protection: The treatment supplements the corrosion protection already applied to the Grenadier at the factory. Protection for exposed areas: Areas subjected to stone chips, dirt and road spray can receive particular attention. Protection from within: Suitable, accessible areas inside the ladder chassis and bodywork receive supplementary protection. Long-lasting creeping action: Mike Sanders Corrosion Protection Grease remains flexible and can continue to spread into narrow gaps when temperatures rise. Durable underbody protection: TimeMAX protects suitable external metal surfaces against typical environmental influences and mechanical stresses. Professional application: Careful preparation, protective masking, specialist cavity probes and endoscopic inspections enable controlled treatment. Long-term preservation: Additional corrosion protection helps preserve the vehicle's structural integrity under demanding operating conditions. Our extensive experience in dealing with corrosion We have been servicing and repairing off-road vehicles for 30 years and know from first-hand workshop experience how continuous exposure to corrosion-promoting conditions can affect vehicles over time. We regularly see how moisture, road salt, dirt and damaged protective coatings can affect the long-term condition of metal components. The INEOS Grenadier already benefits from extensive factory corrosion protection. Its ladder chassis is protected using processes including cathodic dip coating, powder coating and cavity wax, while its body is made from galvanised steel. Despite these factory-applied protective measures, the Grenadier remains an off-road vehicle whose underbody, axles and other components may be exposed to considerable stresses in everyday use. Professional supplementary corrosion protection can provide additional protection in suitable areas. The aim is to support the existing protective systems and help prevent damage before it develops. Comprehensive corrosion protection – protecting relevant components Even on a vehicle with good factory corrosion protection, it makes sense to inspect heavily exposed areas regularly and supplement their protection where appropriate. During treatment, we consider the ladder chassis inside and out, underbody, wheel arches, axles and suitable areas of the doors, rear doors and bonnet. Existing protective coatings can be exposed to demanding conditions after extensive off-road driving, repeated contact with mud and water, or regular winter use. Before applying additional corrosion protection, we therefore assess which surfaces and cavities are accessible and which protective materials are suitable for the existing coatings. Disassembly – accessing concealed areas Additional corrosion protection must be applied where treatment is technically appropriate and the protective material can be used effectively. We therefore remove relevant covers and trim panels, providing access to areas that are concealed or difficult to reach when the vehicle is fully assembled. Dirt and moisture may accumulate behind underbody panels, around joints and in concealed areas. Disassembly allows these locations to be assessed and treated more thoroughly. Protective masking – precise application without unwanted overspray Corrosion protection belongs on the intended surfaces – not on paintwork, windows, brakes or sensitive vehicle components. Before application, the vehicle is carefully covered and masked. Bodywork, painted surfaces, windows, the braking system and other components that must not be treated are protected. This preparation is particularly important on a modern off-road vehicle with numerous electrical and mechanical components, allowing the protective materials to be applied in a controlled manner. Mike Sanders Corrosion Protection Grease – supplementary cavity protection with long-lasting creeping action The key advantage: the grease remains capable of creeping into narrow gaps and seams even after application. Mike Sanders Corrosion Protection Grease is heated to approximately 120 °C and applied using a hot-spray process with specialist cavity probes. The material can be used to provide supplementary corrosion protection inside suitable, accessible cavities. It forms a protective film on treated metal surfaces. Thanks to its temperature-dependent creeping properties, it can continue to spread into narrow gaps, reducing contact between the metal, moisture and oxygen. Important for the Grenadier: The existing factory-applied cavity protection must be considered when selecting and applying additional materials. The treatment is therefore adapted to suitable areas and existing coatings. TimeMAX underbody protection – supplementary protection against moisture, dirt and stone chips The INEOS Grenadier's underbody is designed for demanding use but remains exposed to mechanical stresses and environmental conditions that can contribute to corrosion. Stone chips, mud, road spray and road salt can affect existing protective coatings. Inspections for damage are particularly worthwhile after demanding off-road trips. We use high-quality TimeMAX underbody protection on suitable external underbody surfaces. The durable coating can supplement existing protection and shield treated metal surfaces against environmental influences. It is the combination that makes the difference: TimeMAX protects suitable external underbody surfaces, while Mike Sanders Corrosion Protection Grease is used in appropriate cavities. Normfest Protector Wax – supplementary protection in selected areas We also use Normfest Protector Wax in selected areas where the material is suitable for the existing surfaces and coatings. This corrosion protection wax offers good wetting and creeping properties. Once dry, it forms a flexible, firmly adhering protective film on treated metal surfaces. By selecting protective materials according to their individual properties, additional corrosion protection can be tailored to the different areas of the vehicle. Endoscopic inspection – checking cavities before and after treatment Visual inspection of accessible cavities helps us assess the condition of the areas being treated. Before treatment, suitable cavities are examined using an endoscope, allowing us to inspect visible internal surfaces. Following treatment, another endoscopic visual inspection is carried out to check the application and distribution of the protective material in accessible areas. Reassembly and cleaning – completing the treatment properly Professional reassembly and cleaning are included in the complete workshop service. Once the protective materials have been applied, we remove the masking and reinstall the previously removed trim panels and components. Finally, the areas affected during the work are cleaned, completing the supplementary corrosion protection treatment. Vehicle condition and possible additional work The fixed package price applies to new or nearly new vehicles without heavy contamination or extensive rust damage. If more extensive cleaning or rust removal is required, the additional work will be charged separately. In such cases, we can only provide a firm price after inspecting and assessing the condition of the vehicle. Supplementary corrosion protection may also be beneficial for INEOS Grenadier vehicles that have already been used extensively. However, existing coatings, possible damage and the overall condition of the vehicle must be taken into account. Applying protective materials cannot reverse existing rust damage. Manufacturer warranty notice: Before booking, please check whether additional underbody and cavity corrosion protection could affect the applicable warranty conditions of your INEOS Grenadier. This treatment does not replace any inspections required by the manufacturer. Booking an appointment and treatment duration Please note: The treatment is carried out exclusively at our workshop in 92348 Berg bei Neumarkt in der Oberpfalz, Bavaria, Germany. Our workshop is easily accessible and is located approximately 35 km from Nuremberg, 70 km from Regensburg and 145 km from Munich. When placing your order, please provide the model year and exact version of your INEOS Grenadier, along with your telephone number. This allows us to assess the work required for your particular vehicle and arrange a suitable appointment. Alternatively, you can contact us first on +49 9181 466 644 before placing your order. The comprehensive treatment, including preparation, protective masking, supplementary corrosion protection, inspection, reassembly and cleaning, normally takes 2–3 days. How Often Should the Corrosion Protection Be Inspected? Professionally applied corrosion protection provides long-term protection against rust and corrosion. Nevertheless, we recommend having the cavity and underbody protection inspected at regular intervals. How often an inspection is advisable depends primarily on how the vehicle is used and the environmental conditions it is exposed to. In particular, off-road driving, heavy road salt exposure and challenging weather conditions can place additional strain on the protective coating. Our recommended inspection intervals: Intensive off-road use (Heavy Off-Road): annually Regions with heavy road salt exposure: annually Moderate off-road use or expedition vehicles in Northern Europe: every 2–3 years Moderate off-road use or expedition vehicles in Southern Europe: every 4–6 years Predominantly on-road use: every 7–10 years During an inspection, the protective coating is checked to ensure it remains complete and intact, and to identify any areas that may require additional treatment. Regular inspections help maintain the vehicle's long-term value and allow potential corrosion issues to be addressed at an early stage.
Prices incl. VAT;
Your tyre for extreme conditions: BFGoodrich KM3 Offroad Goodrich Mud Terrain T/A KM3 255/85R16 119QThe off-road tire BFGoodrich Mud Terrain T / A KM3 is primarily intended for off-road use, it is less suitable for driving on paved roads. The tires of this type are characterized by a special tread, which is responsible for safety when driving off-road, as well as a reinforced construction. The MT tires are the best way out for drivers who need tires for mud and water when driving off-road and are not afraid of rocky slopes. The very deep grooves of the tread and the massive blocks make driving on these tires safe. Due to the wide gaps, the tire cleans itself up quickly, which makes driving easier on sand, for example. This typical terrain model is also reinforced so that drivers do not have to worry about the tire being destroyed when driving in difficult terrain. Available in:255/85 R16235/85 R16 click here LR WOLF Steel Wheel 6.5x16"- corresponds to part number ANR4583 PM- dimensions 6,5 x16", offset 20,6 If the wheels need to be rebalanced at a later date, we recommend balancing the rims for the Land Rover Defender using bolt or bolt circle centring. Important information regarding winter suitability: The BFGoodrich Mud-Terrain T/A KM3 is a Mud-Terrain tyre (MT) with POR marking (Professional Off-Road), specifically developed for demanding off-road use. It does not carry the Alpine symbol (3PMSF/three-peak mountain snowflake) and is not classified as a winter tyre, either in terms of its rubber compound and tread design or its markings. This tyre is not designed for use in winter road conditions such as snow, ice or icy roads. The POR marking does not constitute winter tyre certification.
Prices incl. VAT;
Premium Long-Term Underbody and Cavity Corrosion Protection with Mike Sanders and TimeMAX for Mercedes G-Class W463 Long-lasting corrosion protection for your Mercedes G-Class W463: Using Mike Sanders Corrosion Protection Grease, TimeMAX underbody protection and supplementary Normfest Protector Wax, our workshop team draws on 30 years of experience to protect corrosion-prone areas – both inside and out. At our specialist 4x4 workshop in Berg bei Neumarkt, Bavaria, between Nuremberg and Regensburg, we offer professional underbody and cavity corrosion protection for the Mercedes G-Class W463. This helps protect your G-Class's ladder chassis, underbody and corrosion-prone bodywork against rust, avoid costly welding and repairs, and preserve the vehicle's structural integrity over the long term. The following services are included in the complete package: Comprehensive corrosion protection: Treatment of the ladder chassis inside and out, underbody, wheel arches, axles, doors, rear door and bonnet. Professional preparation: Removal of relevant covers and trim panels to gain access to hard-to-reach areas. Extensive protective masking: Careful masking of the vehicle, particularly bodywork, painted surfaces, windows, brakes and other components that must not be treated. Mike Sanders cavity protection: Hot-spray application using specialist cavity probes for effective corrosion protection inside enclosed areas and long-term creeping action. TimeMAX underbody protection: High-quality, durable protective coating for the underbody surfaces to be treated. Normfest Protector Wax: Supplementary corrosion protection in selected areas. Endoscopic inspection: Visual inspection of accessible cavities before and after treatment. Reassembly and cleaning: Reinstallation of removed components and final cleaning. A detailed explanation of each stage of the treatment can be found below. Your benefits – and what they mean for your Mercedes G-Class Long-term corrosion protection: Reduces contact between treated metal surfaces, moisture and oxygen, helping to slow down corrosion processes. Protection from within: Protects vulnerable areas inside the ladder chassis and bodywork, where rust may develop unnoticed. Long-lasting creeping action: Mike Sanders Corrosion Protection Grease continues to spread into narrow seams and overlapping panels after application. Durable underbody protection: Protects against moisture, road salt, road spray and the typical stresses of road and off-road use. Three premium branded products: Mike Sanders, TimeMAX and supplementary Normfest products are used according to their individual properties. Professional application: Careful disassembly, masking, specialist cavity probes and endoscopic inspections enable thorough treatment. Long-term preservation: Preventative corrosion protection helps avoid expensive rust damage and preserve the vehicle's structural integrity. Our extensive experience in dealing with corrosion We have been servicing and repairing off-road vehicles for 30 years and know from first-hand experience just how serious rust damage to the chassis, underbody and bodywork can become. Particularly on older Mercedes G-Class vehicles, concealed corrosion can lead to extensive and expensive repairs. Areas that deserve particular attention on the W463 include the ladder chassis and its crossmembers and mounting points, lower door edges, sills, wheel arches, the windscreen surround and the rear door. Moisture and dirt can collect in these areas and contribute to corrosion. Our experience helps us identify vulnerable areas and treat them with particular care. Protect your G-Class before minor rust spots develop into major repairs. Comprehensive corrosion protection – protecting all relevant components Effective long-term corrosion protection must go beyond the visible underbody. Internal cavities are equally important. We treat the ladder chassis inside and out, the underbody, wheel arches, axles and corrosion-prone areas of the doors, rear door and bonnet. Moisture can accumulate inside chassis sections, along panel seams, welded joints and bodywork transitions. Rust often develops unnoticed in these areas and can gradually damage the vehicle's structure. By combining different protective materials, we can address both external metal surfaces and difficult-to-reach internal cavities. Disassembly – accessing concealed corrosion-prone areas Effective corrosion protection must also reach areas that are not directly accessible when the vehicle is fully assembled. We therefore remove relevant covers and trim panels. This allows us to uncover important access points and apply protective materials precisely in areas that would otherwise be difficult to reach. Dirt and moisture may accumulate around sill sections, behind trim panels and around attachments. These areas should not be overlooked during comprehensive corrosion protection. Protective masking – precise application without unwanted overspray Corrosion protection belongs on the intended surfaces – not on paintwork, windows or brakes. Before treatment, the vehicle is carefully covered and masked. Particular attention is paid to protecting bodywork, painted surfaces, windows, the braking system and other components that must not come into contact with the products. This extensive preparation enables controlled application and reduces the risk of unwanted contamination or interference with sensitive components. Mike Sanders Corrosion Protection Grease – lasting creeping action inside cavities The key advantage: the corrosion protection grease remains capable of creeping into narrow gaps and panel seams, even after application. Mike Sanders Corrosion Protection Grease is heated to approximately 120 °C and applied using a hot-spray process with specialist cavity probes. This allows us to introduce the material deep inside the ladder chassis and other accessible cavities of the Mercedes G-Class. The grease forms a protective film on treated metal surfaces. Thanks to its temperature-dependent creeping properties, it continues to spread and can penetrate welded seams, overlapping panels and particularly narrow gaps. How it protects: The grease film forms a barrier against moisture and oxygen. Unlike rigid coatings, it remains flexible and can continue to provide protection during temperature-related expansion and contraction. TimeMAX underbody protection – protection against moisture, dirt and stone chips The underbody of a G-Class is exposed to demanding conditions in everyday road use as well as off-road driving. Stone chips, road spray, road salt, mud and dirt can damage existing protective coatings or gradually wear them away. Corrosion may then begin on exposed metal surfaces. We use high-quality TimeMAX underbody protection on the external underbody surfaces to be treated. The durable coating protects against corrosion-promoting environmental influences and typical mechanical stresses. It is the combination that makes the difference: TimeMAX protects external underbody areas, while Mike Sanders Corrosion Protection Grease is particularly effective inside cavities and narrow gaps. Normfest Protector Wax – additional protection in selected areas We also use Normfest Protector Wax in selected areas to complement the overall treatment. This corrosion protection wax offers good wetting and creeping properties. Once dry, it forms a flexible, firmly adhering protective film on the treated metal surfaces. It is applied wherever its properties are particularly suitable for the area concerned, allowing the different protection systems to complement one another. Endoscopic inspection – checking cavities before and after treatment Hard-to-reach areas should also be inspected – not just the visible surfaces. Before treatment, we examine accessible cavities using an endoscope. This allows us to assess the condition of internal surfaces and identify possible rust spots. Following treatment, another endoscopic visual inspection is carried out to check the application and distribution of the protective material in the areas that can be inspected. Reassembly and cleaning – completing the treatment properly The complete package also includes professionally restoring the vehicle to its assembled condition after treatment. Once the protective materials have been applied, we remove the masking and reinstall the previously removed trim panels and components. Finally, the areas affected during the work are cleaned, completing the comprehensive corrosion protection treatment. Vehicle condition and possible additional work The fixed package price applies to new or nearly new vehicles without heavy contamination or extensive rust damage. If more extensive cleaning or rust removal is required, the additional work will be charged separately. In such cases, we can only provide a firm price after inspecting and assessing the condition of the vehicle. Professional corrosion protection can also be worthwhile for older Mercedes G-Class vehicles with existing rust. By shielding treated metal surfaces from moisture and oxygen, further corrosion can be slowed down. However, existing rust damage cannot be reversed by applying protective materials. Careful preparation and, where necessary, prior repairs are essential. Booking an appointment and treatment duration Please note: The treatment is carried out exclusively at our workshop in 92348 Berg bei Neumarkt in der Oberpfalz, Bavaria, Germany. Our workshop is easily accessible and is located approximately 35 km from Nuremberg, 70 km from Regensburg and 145 km from Munich. When placing your order, please provide the model year and exact version of your Mercedes G-Class W463, along with your telephone number. A member of our team will contact you to arrange an appointment and confirm the work required for your particular vehicle. Alternatively, you can contact us first on +49 9181 466 644 to arrange an appointment before ordering the service. The comprehensive treatment, including disassembly, extensive protective masking, application, inspection, reassembly and cleaning, normally takes 2–3 days. How Often Should the Corrosion Protection Be Inspected? Professionally applied corrosion protection provides long-term protection against rust and corrosion. Nevertheless, we recommend having the cavity and underbody protection inspected at regular intervals. How often an inspection is advisable depends primarily on how the vehicle is used and the environmental conditions it is exposed to. In particular, off-road driving, heavy road salt exposure and challenging weather conditions can place additional strain on the protective coating. Our recommended inspection intervals: Intensive off-road use (Heavy Off-Road): annually Regions with heavy road salt exposure: annually Moderate off-road use or expedition vehicles in Northern Europe: every 2–3 years Moderate off-road use or expedition vehicles in Southern Europe: every 4–6 years Predominantly on-road use: every 7–10 years During an inspection, the protective coating is checked to ensure it remains complete and intact, and to identify any areas that may require additional treatment. Regular inspections help maintain the vehicle's long-term value and allow potential corrosion issues to be addressed at an early stage.
Prices incl. VAT;
Premium Long-Term Underbody and Cavity Corrosion Protection with Mike Sanders and TimeMAX for BAW 212 Long-lasting corrosion protection for your BAW 212: Using Mike Sanders Corrosion Protection Grease, TimeMAX underbody protection and supplementary Normfest Protector Wax, our workshop team draws on 30 years of experience to protect the corrosion-prone areas of your off-road vehicle – both inside and out. At our specialist 4x4 workshop in Berg bei Neumarkt, Bavaria, between Nuremberg and Regensburg, we offer professional underbody and cavity corrosion protection for the BAW 212. Protect your BAW 212 from the outset. This helps prevent corrosion affecting the ladder chassis, underbody and vulnerable bodywork, avoid expensive repairs later and preserve your vehicle's structural integrity over the long term. The following services are included in the complete package: Comprehensive corrosion protection: Treatment of the ladder chassis inside and out, underbody, wheel arches, axles, doors, tailgate and bonnet. Professional preparation: Removal of relevant covers and trim panels to gain access to hard-to-reach areas. Extensive protective masking: Careful masking of bodywork, painted surfaces, windows, brakes and other components that must not be treated. Mike Sanders cavity protection: Hot-spray application using specialist cavity probes for long-lasting, creeping corrosion protection. TimeMAX underbody protection: High-quality, durable coating for the underbody surfaces to be treated. Normfest Protector Wax: Supplementary corrosion protection in selected areas. Endoscopic inspection: Visual inspection of accessible cavities before and after treatment. Reassembly and cleaning: Reinstallation of removed components and final cleaning. A detailed explanation of each stage of the treatment can be found below. Your benefits – and what they mean for your BAW 212 Corrosion prevention from the outset: Early treatment protects accessible metal surfaces before heavy contamination or rust damage develops. Protection from within: Protects areas inside the ladder chassis and bodywork where moisture can accumulate. Long-lasting creeping action: Mike Sanders Corrosion Protection Grease remains flexible and continues to spread into narrow gaps and seams when temperatures rise. Durable underbody protection: Protects treated surfaces against moisture, dirt, road salt and typical off-road stresses. Three premium branded products: Mike Sanders, TimeMAX and supplementary Normfest are used according to their individual material properties. Professional application: Disassembly, careful masking, specialist cavity probes and endoscopic inspections enable thorough treatment. Long-term preservation: Preventative corrosion protection helps avoid future rust damage and expensive repairs. Our extensive experience in dealing with corrosion We have been servicing and repairing off-road vehicles for 30 years and know from first-hand workshop experience what rust damage can do to chassis, axles, underbody components and bodywork. Our experience demonstrates the importance of early corrosion protection, especially for vehicles regularly driven off-road or during winter. The BAW 212 combines traditional off-road construction with modern technology. Its robust ladder chassis and suspension components designed for demanding terrain are nevertheless exposed to moisture, dirt, road spray and road salt. That is why we focus on preventative protection before significant corrosion damage develops. Early treatment is generally much easier than removing rust and repairing components that have already been damaged. Comprehensive corrosion protection – protecting all relevant components Long-term corrosion protection begins well beyond the visible underside of the vehicle. Internal chassis sections and body cavities deserve particular attention. We treat the ladder chassis inside and out, the underbody, wheel arches, axles and corrosion-prone areas of the doors, tailgate and bonnet. Moisture and dirt can accumulate inside cavities, around panel joints and in hard-to-reach areas. These areas are particularly exposed after driving along wet tracks, through mud or on salted roads during winter. Comprehensive treatment specifically protects vulnerable metal surfaces and supplements the existing corrosion protection of your BAW 212. Disassembly – accessing concealed areas Effective corrosion protection must also reach areas that cannot be seen directly from outside. We therefore remove relevant covers and trim panels before treatment. This provides access to important application points and otherwise difficult-to-reach areas. It allows us to apply protective materials precisely and introduce them into internal cavities instead of treating only visible surfaces. Protective masking – precise application without unwanted overspray Corrosion protection belongs on the intended surfaces – not on paintwork, windows or brakes. Before treatment, the vehicle is carefully covered and masked. Particular attention is paid to protecting bodywork, painted surfaces, windows, the braking system and other sensitive components that must not be treated. This extensive preparation enables controlled application and reduces the risk of unwanted contamination. Mike Sanders Corrosion Protection Grease – long-term protection inside the ladder chassis The key advantage: Mike Sanders Corrosion Protection Grease remains capable of creeping into narrow gaps and panel seams even after application. The grease is heated to approximately 120 °C and applied using a hot-spray process with specialist cavity probes. This allows us to introduce the material into accessible cavities inside the ladder chassis and bodywork. A protective grease film forms on the treated metal surfaces. Thanks to its temperature-dependent creeping properties, the material can also reach narrow overlapping panels, welded seams and gaps. How it protects: The grease film reduces contact between the metal surfaces, moisture and oxygen, helping to prevent corrosion over the long term. TimeMAX underbody protection – protection for road and off-road use Even a new off-road vehicle is continually exposed to moisture, dirt and mechanical stresses underneath. Stone chips, road spray, road salt and mud can wear down or damage existing protective coatings. Where metal surfaces become exposed, corrosion may begin. We use high-quality TimeMAX underbody protection on the external underbody surfaces to be treated on the BAW 212. The durable coating forms a protective barrier against corrosion-promoting environmental influences. It is the combination that makes the difference: TimeMAX protects more heavily exposed external underbody areas, while Mike Sanders is particularly effective inside enclosed cavities. Normfest Protector Wax – additional protection in selected areas We also use Normfest Protector Wax in selected areas to complement the treatment. This corrosion protection wax offers good wetting and creeping properties. Once dry, it forms a flexible, firmly adhering protective film. It can therefore be used in areas where its particular material properties are suitable, allowing the different protective products to work together as a vehicle-specific treatment. Endoscopic inspection – checking cavities before and after treatment Protection should not simply be applied to visible surfaces; accessible cavities should also be inspected. Before treatment, we examine accessible cavities using an endoscope, allowing us to assess the condition of internal surfaces. Following treatment, another endoscopic visual inspection is carried out to check the application and distribution of the protective material in the areas that can be inspected. Reassembly and cleaning – completing the treatment properly Professional corrosion protection does not end once the protective materials have been applied. After treatment, we remove the protective masking and reinstall the previously removed trim panels and components. Finally, the areas affected during the work are cleaned, completing the corrosion protection treatment. Vehicle condition and possible additional work The fixed package price applies to new or nearly new vehicles without heavy contamination or extensive rust damage. If more extensive cleaning or rust removal is required, the additional work will be charged separately. In such cases, we can only provide a firm price after inspecting and assessing the condition of the vehicle. Professional corrosion protection may also be worthwhile for vehicles that have already been in use. If rust is present, the affected areas must first be assessed and, if necessary, prepared or repaired. Corrosion protection can slow down further deterioration but cannot reverse existing damage. Booking an appointment and treatment duration Please note: The treatment is carried out exclusively at our workshop in 92348 Berg bei Neumarkt in der Oberpfalz, Bavaria, Germany. Our workshop is easily accessible and is located approximately 35 km from Nuremberg, 70 km from Regensburg and 145 km from Munich. When placing your order, please provide the model year and exact version of your BAW 212, along with your telephone number so that we can arrange an appointment. A member of our team will contact you to schedule your visit. Alternatively, you can contact us first on +49 9181 466 644 before placing your order. The comprehensive treatment, including disassembly, protective masking, application, inspection, reassembly and cleaning, normally takes 2–3 days. How Often Should the Corrosion Protection Be Inspected? Professionally applied corrosion protection provides long-term protection against rust and corrosion. Nevertheless, we recommend having the cavity and underbody protection inspected at regular intervals. How often an inspection is advisable depends primarily on how the vehicle is used and the environmental conditions it is exposed to. In particular, off-road driving, heavy road salt exposure and challenging weather conditions can place additional strain on the protective coating. Our recommended inspection intervals: Intensive off-road use (Heavy Off-Road): annually Regions with heavy road salt exposure: annually Moderate off-road use or expedition vehicles in Northern Europe: every 2–3 years Moderate off-road use or expedition vehicles in Southern Europe: every 4–6 years Predominantly on-road use: every 7–10 years During an inspection, the protective coating is checked to ensure it remains complete and intact, and to identify any areas that may require additional treatment. Regular inspections help maintain the vehicle's long-term value and allow potential corrosion issues to be addressed at an early stage.
Prices incl. VAT;
Complete wheel set BF Goodrich 265/65R18 117R All Terrain T/A KO2 on Borbet CW7 alloy wheels BFGoodrich ALL Terrain T/A KO2 265/65 R18 117R: The BFGoodrich All Terrain T/A KO2 265/65 R18 117R guarantees driving fun even off the paved roads. It is very stable and has good road grip. It also handles not too difficult terrain with some mud, loose ground well. For extreme terrain and little road use, however, a MUS tyre is recommended. In the AT range BFGoodrich is a very good choice. A SPECIAL TYRE MIXTURE that is resistant to cuts and chipping on the sidewalls to withstand sharp stones. Designed to resist chipping and cracking caused by sharp stones and obstacles in the terrain. IMPRINTED CLAMPS on the sides for more grip and better sidewall protection. The large crampons on the sidewall are synonymous with bite, especially when the tyre is rolling at low pressure. Greater thickness of rubber on the sidewall protects the tyre from off-road hazards. STRENGTHENED CABLES for less sensitive sidewalls. Flank weakness can spoil off-road activities very quickly. Oversized sidewall cables give the carcass the protection it needs for tough off-road use. Performance 50% off-road - 50% on-road Tyre width 265 Ratio of sidewall height to tyre width in percent 65 Rim diameter: 18" Load index: 117/114 Speed index: R 3PMSF Alpine symbol (so-called snowflake): yes M+S marking: yes Weight: 23,06 per tyre Tyre type: All-season Tyre type: Radial Noise emission: 74db Noise class (from 1-quiet to 3-noise): 2 Wet grip (grip on rain-soaked road): B Fuel efficiency (A to G): F When ordering, please let us know whether the white lettering is to be fitted inside or outside.BORBET CW7 alloy wheels 18 inch:With the BORBET CW7 in the "Commercial Wheels" category, a new wheel is now presented that is not only convincing in terms of design, but also with high wheel loads of up to 1,400 kg.The CW7 stands for a new, striking look that is not only defined by the number of spokes, but is also made for the real movers and shakers among vehicles. From vans to off-roaders to motorhomes. Manufacturer: Borbet Brand: CW7 Size/offset: 7.5x18", offset 47 Colour: either matt black or matt bronze Suitability: for Ineos Grenadier Certification: for 255/65R18 255/70R18 265/65R18 A01) K02) Included in delivery: Rim, incl. matching wheel nuts High wheel load Winterproof Scope of delivery: Rim, incl. matching wheel nuts / Note: the wheel nuts of the original Ineos alloy rims also fit on these rims!The price refers to 4 or 5 complete wheels incl. mounting and balancing. This article is bulky goods.
Prices incl. VAT;
BF Goodrich All Terrain T/A KO3 all-season tyre on Wolf steel rim Tyre size: 235/85R16 Rim size/offset: 6.5x16" T20.6 BFGoodrich® All-Terrain T/A KO3 - One tyre for all occasions. Wherever the journey takes you: the BFGoodrich® All-Terrain T/A KO3 is ready for action. This 3PMSF-certified tyre offers strong grip on mud and snow. With its serrated tyre shoulder design and mud phobic bars, it also contributes to controlled handling on and off the road. Brand: BFGOODRICH Tread pattern: ALL-TERRAIN T/A KO3 Dimension: LT235/85R Diameter: 16" Load index: 120 Speed index: S Fuel efficiency class: E Wet grip class: C External rolling noise classification: B External rolling noise: 74 dB Snowflake symbol: yes Resistance on a new level. BFGoodrich® all-season off-road tyres for SUVs, off-road vehicles and light trucks Designed for high grip and controlled handling on and off-road CoreGard technology and improved rubber compound for increased resistance and durability Optimised tread design for even wear and longer service life Off-road design for increased off-road performance All-season tyre When ordering, please let us know whether the white lettering should be mounted on the inside or outside. We recommend to balance the rims for the Land Rover Defender bolt or bolt circle centred. The rims used are LR WOLF rims (black) 6.5x16 inch, offset 20.6, which correspond to part number ANR4583 PMGEN. These are the ORIGINAL rims from Land Rover (not a replica!). These black rims can also be ordered powder-coated in the colour white or black. Note: We always recommend the powder-coated rims, as the rims with a primer are still susceptible to corrosion due to the open pores alone. If the primed rims corrode, there is therefore no right of return. Please note: Wheel nuts for aluminium rims cannot be used on steel rims. Balancing Defender wheels on conventional centre-centring balancing machines often leads to errors. For this reason, we use a so-called stud centring system, in which the wheel is balanced using a special adapter plate.
Prices incl. VAT;
BF Goodrich All Terrain T/A KO3 all-season tyre on CLASSIC steel rim Tyre size: 265/75R16 Rim size/offset: 8x16" offset 0 BFGoodrich® All-Terrain T/A KO3 - One tyre for all occasions. Wherever the journey takes you: the BFGoodrich® All-Terrain T/A KO3 is ready for action. This 3PMSF-certified tyre offers strong grip on mud and snow. With its serrated tyre shoulder design and mud-repellent Mud Phobic Bars, it also contributes to controlled handling on and off the road. Brand: BFGOODRICH Tread pattern: ALL-TERRAIN T/A KO3 Dimension: LT265/75R Diameter: 16 inch Load index: 119 Speed index: S Fuel efficiency class: E Wet grip class: C External rolling noise classification: B External rolling noise: 74 dB Snowflake symbol: yes Resistance on a new level. BFGoodrich® all-season tyre for off-road driving with SUVs, off-road vehicles and light trucks Designed for high grip and controlled handling on and off-road CoreGard technology and improved rubber compound for increased resistance and durability Optimised tread design for even wear and longer service life Off-road design for increased off-road performance All-season tyre When ordering, please let us know whether the white lettering should be mounted on the inside or outside. If the wheels need to be rebalanced at a later date, we recommend balancing the rims for the Land Rover Defender using bolt or bolt circle centring. The tyres are fitted with the popular ANR Classic rims 16 inch. These are optionally available in primed black, powder-coated black and powder-coated white. The ANR Classic were designed with the Landrover history in the background, manufactured exclusively for Nakatanenga and really round off every Defender perfectly. The price refers to 4 or 5 complete wheels incl. mounting / balancing. This article is bulky goods
Prices incl. VAT;
Mobile parking heater with aluminum box, various versions Make way, here comes the second generation of our mobile parking heaters in a box! We have packed even more technology, even more experience and even more customer feedback into our new mobile heating boxes. If you are looking for a small, self-sufficient and portable heat source with unrivaled capacity for cold days and nights in unheated outdoor shelters or temporary accommodation, you get everything you need (or want) in a small, weatherproof aluminum box. Available in three modular versions with different configurations, the Nakatanenga heating box provides the perfect, independent heat source for tents, gazebos, garden sheds, mountain huts, snack stands, stalls and much more. The heart of the mobile parking heater is the Autoterm Luft 2D, a diesel-powered air heater with a maximum heat output of 1.8 kW and a diesel consumption of just under a quarter of a liter per hour at full power. With a tank capacity of 18 liters in the twin-tank version, this means that it can heat at full throttle for over 70 hours. The economical unit, which is also very quiet at 55 dB thanks to the exhaust silencer, is controlled by a digital control unit with timer in the version with two batteries and can also be switched on and off by radio remote control. This allows you to preheat your camper, roof tent, caravan or hunting lodge in good time for getting up or for the evening, for example, and operate it from the place where you are staying or sleeping inside*. In contrast to the previous models, the five versions of our mobile parking heater are now only available in one box size, namely 42 liters. This is significantly more compact than the old version in the large version and only slightly more voluminous than the small model from before. What is the advantage? The new universal crate has a modular interior with a powerful performance. Depending on whether you need tanks, batteries or both in the box, you can choose the appropriate version when purchasing: with 9.2 L single or 18.4 L double tank, each without battery, as well as with single tank, two batteries and digital control. However, it can also be easily retrofitted or converted if requirements change. This is made possible by elaborately designed brackets in the box and the use of specially manufactured, made-to-measure tanks. Features of heating box 1 and 2 (without battery) - Heating unit 1 with 1 x 9.2-litre diesel tank - Heating unit 2 with 2 x 9.2 = 18.4-litre diesel tank - USB interface for charging smartphone, power bank, tablet, etc.- Capacity display- PU5 control panel (without timer and storage options)- 12 V connection socket for supplied pole terminal cable- Alternatively, a cable for cigarette lighter (KMSH cable) can be used- 2 radio remote controls- Connection option for external temperature sensor (the connection is inside the box, not outside)” Features of heater box 3 (with 2 AGM batteries) - 2 x 33 Ah 12-volt AGM batteries, leak-proof and maintenance-free - 9.2-litre diesel tank - USB interface for charging smartphone, power bank, tablet, etc.- Capacity display- Comfort Control control panel (with timer and memory option)- SAE connection socket (suitable for Optimate chargers or Optimate solar charger)- 2 radio remote controls- Connection option for external temperature sensor (the connection is inside the box, not outside) Features of heating box 4 (with 1 LiFePo battery) - 1x 35 Ah 12-volt LiFePO4 lithium service battery, suitable for long-term storage and extremely temperature-stable - 9.2-litre diesel tank - USB interface for charging smartphone, power bank, tablet etc.- Capacity display- Comfort Control control panel (with timer and memory option)- SAE connection socket (suitable for Optimate chargers or Optimate solar charger)- 2 radio remote controls- Connection option for external temperature sensor (the connection is inside the box, not outside)-> Please only use LiFePo-compatible chargers Features of heating box 5 (with 2 LiFePo batteries) - 2x 35 Ah 12-volt LiFePO4 lithium service batteries, suitable for long-term storage and extremely temperature-stable - 9.2-litre diesel tank - USB interface for charging smartphone, power bank, tablet, etc.- Capacity display- Comfort Control control panel (with timer and memory option)- SAE connection socket (suitable for Optimate chargers or Optimate solar charger)- 2 radio remote controls- Connection option for external temperature sensor (the connection is inside the box, not outside)”-> please only use LiFePo-compatible chargers The warm air is transported via a firmly screw-fastened, waterproof Flexi hose. As the warm air hose is different for every user and every requirement, we do not include a standard length, but leave it up to you to order the desired length separately here in the store, with or without a silicone sleeve. You can find the perfect storage bag for the Flexi hose here in the store. Regardless of the configuration, the mobile parking heaters are always easy to transport and make the difference between experiencing and suffering in the cold seasons. Whether it's an aurora safari, selling cookies at the Christmas market or winter camping in a roof tent, nothing is really fun if you freeze to death. *ATTENTION: As a precaution, we would like to point out that operation in closed rooms is not permitted due to the risk of poisoning from exhaust fumes. In addition, for optimum heating performance, make sure that the air inlets for combustion and hot air are positioned so that they are protected from the weather. Dimensions Internal dimensions 550x350x220 mm External dimensions 580x380x240 mm Unladen weight: Heating unit 1, without battery and with 1 tank: 16 kg Heating unit 2, without battery and with 2 tanks: 18 kg Heating unit 3, with 2 AGM batteries and 1 tank: 45 kg Heating unit 4, with 1 LiFePo battery and 1 tank: 19 kg Heating box 5, with 2 LiFePo batteries and 1 tank: 24 kg Depending on how many starts are made, the battery lasts at least 40 h, but more likely between 60 and 70 h. LiFePo4 batteries - i.e. batteries with a lithium iron phosphate cathode - are the ideal supply batteries for camping or electrical work on the move. In contrast to conventional lead-acid AGM technology, lithium batteries combine superior charging properties with much lower weight and volume and a long service life. LiFePo4 batteries can be deep-discharged without any problems, which sooner or later leads to irreparable damage with AGM batteries, as the rule of thumb here is that you should never draw more than 50% charge. If you are not dependent on the greater cold tolerance of AGM batteries, you should definitely consider the higher costs for LiFePo4 batteries and compatible charging technology. The weight and space savings, the long service life and the uncomplicated discharging and charging of the battery are strong arguments in favor of the investment. What's more, LiFePo4 technology is also extremely safe And a special note on aluminum: Although we take the utmost care during storage and shipping, as with all our products, aluminum boxes can always show minimal scratches, stains, dents or other surface features upon delivery. These are material-related and result from the specific properties of the light metal. In contact with oxygen, aluminum forms a natural, corrosion-protecting patina and is also relatively soft compared to steel, which is three times heavier. This makes the material ideal for use in sheet metal, especially when weight and resistance are important. On the other hand, however, it also means that aluminum can never be completely free of patina or other marks, even on delivery: Small scratches, stains etc. therefore do not constitute grounds for complaint. Ultimately, aluminum boxes are intended to be robust objects of daily use. Like everything that is actively used, they develop an individual patina and every trace of use tells a story. So, have fun with it! If you want to heat the interior of your vehicle, we offer an installation service for warm air ducting through a ventilation plate. Please note the variants without batteries: Most portable power stations or battery boxes (such as Goal Zero, Eco Flow, Bluetti etc.) are unfortunately not suitable for operating mobile parking heaters. The heater requires up to 15A as starting current and when shutting down, but very few battery boxes can provide this. Suitable battery boxes for operating the mobile parking heater Please note the legal information on batteries HERE. For certain types of batteries, we are legally obliged to charge a deposit. EQUIPMENT HIRE: Hire an AUTOTERM 2D12 mobile diesel/air heater in an aluminium case with battery If you only need a mobile space heater for a short period, you can easily hire one here: Click here to make a no-obligation enquiry! Rental prices 1 week(7 days) 2 week(14 days) 3 week(21days) 4 week(30 days) AUTOTERM 2D12 in an aluminium case WITH battery 351€ 467€ 537€ 584€ Prices include VAT PLEASE NOTE: As a precaution, we would like to point out that the appliance must not be used indoors due to the risk of poisoning from exhaust fumes. Furthermore, to ensure optimum heating performance, please ensure that the air intakes for combustion and hot air are positioned in a way that protects them from the weather. Our hire heaters (battery-powered) are supplied in wooden crates and delivered by a haulage contractor. The diesel tank is empty on delivery and MUST also be empty when returned!
Prices incl. VAT;
Robust and powerful: BF Goodrich KO2 on Borbet CW7 – the perfect complete wheel set for your INEOS Grenadier BF Goodrich ALL Terrain T/A KO2 265/65 R18 117R: The BFGoodrich All Terrain T/A KO2 265/65 R18 117R guarantees driving pleasure even off the beaten track. It is very stable and has good road grip. It also copes well in not too difficult terrain with some mud and loose ground. For extreme terrain and little road use, however, a MUS tire is recommended. In the AT area, BFGoodrich is a very good choice. A SPECIAL TIRES compound that is resistant to cuts and chipping on the sidewalls to withstand sharp rocks. Designed to resist chipping and cracking that can be caused by sharp rocks and obstacles in the terrain. IMPRINTED CLAMPS on the sides for more grip and better sidewall protection. The large crampons on the sidewall are synonymous with bite, especially when the tire is rolling at low pressure. A greater thickness of rubber on the sidewall protects the tire from off-road hazards. REINFORCED CABLES for less sensitive sidewalls. A weak sidewall can spoil off-road activities very quickly. Oversized sidewall cables provide the carcass with the necessary protection for tough off-road use. Performance 50% off-road - 50% road Tire width 265 Ratio of sidewall height to tire width in percent 65 Rim diameter: 18" Load index: 117 Speed index: R 3PMSF Alpine symbol (so-called snowflake): yes M+S marking: yes Weight: 23.06 per tire Tire type: All-season Tire construction: Radial Noise emission: 74db Noise class (from 1-quiet to 3-noisy): 2 Wet grip (grip on wet roads): B Fuel efficiency (A to G): F The tyres are already mounted on the rims and have TPMS sensors installed. The white lettering is mounted on the outside! BORBET CW7 18 inch alloy wheel The BORBET CW7 in the “Commercial Wheels” category is a new wheel that not only impresses in terms of design, but also with high wheel loads of up to 1,400 kg. The CW7 stands for a new, striking look that is not just defined by the number of spokes, but is perfect for the real movers and shakers among vehicles. From vans to off-roaders and motorhomes. Manufacturer: Borbet Brand: CW7 Size/offset: 7.5x18", ET 47 Color: matt black Suitability: for Ineos Grenadier Approval: for 255/65R18 255/70R18 265/65R18 A01) K02) Scope of delivery: rim, incl. matching wheel nuts High wheel load Winter-proof Scope of delivery: rim, incl. matching wheel nuts The price refers to 5 complete wheels incl. fitting and balancing. This article is bulky goods.
Prices incl. VAT;
BF Goodrich All Terrain T/A KO3 all-season tyre on Dotz steel rim for Defender up to MY2016 Tyre size: 265/75R16 Rim size/offset: 7x16" offset 8 BFGoodrich® All-Terrain T/A KO3 - One tyre for all occasions. Wherever the journey takes you: the BFGoodrich® All-Terrain T/A KO3 is ready for action. This 3PMSF-certified tyre offers strong grip on mud and snow. With its serrated tyre shoulder design and mud phobic bars, it also contributes to controlled handling on and off the road. Brand: BFGOODRICH Tread pattern: ALL-TERRAIN T/A KO3 Dimension: LT265/75R Diameter: 16" Load index: 119 Speed index: S Fuel efficiency class: E Wet grip class: C External rolling noise classification: B External rolling noise: 74 dB Snowflake symbol: yes Resistance on a new level. BFGoodrich® all-season off-road tyres for SUVs, off-road vehicles and light trucks Designed for high grip and controlled handling on and off-road CoreGard technology and improved rubber compound for increased resistance and durability Optimised tread design for even wear and longer service life Off-road design for increased off-road performance All-season tyre When ordering, please let us know whether the white lettering should be mounted on the inside or outside. If the wheels need to be rebalanced at a later date, we recommend balancing the rims for the Land Rover Defender using bolt or bolt circle centring. The rims used are DOTZ DAKAR steel rims in 7x16 inch format with approval for Land Rover Defender 90/110, Range Rover Classic and Discovery, which are available in silver, bronze or black. Please note: Wheel nuts for aluminium rims cannot be used on steel rims. The balancing of Defender wheels often leads to errors on conventional centre-centring balancing machines. For this reason, we rely on a so-called stud centring system, which uses a special adapter plate to balance the wheel as if it were mounted on a vehicle. The price refers to 4 or 5 complete wheels incl. fitting / balancing. This article is a bulky item.
Prices incl. VAT;
Wheel set Dotz Dakar Steel Rim and BFGoodrich All Terrain Tire A bigger footprint with Dotz Dakar Steel Rims and BFGoodrich All Terrain tires not only suits Defenders, G-Wagons etc. but also the Jimny II GJ HJ, turning tiny Jimny into Big Jim. The fact that the Dotz Dakar has become a classic for all kinds of 4x4‘s is no accident. The steel rim with its timeless design and its high-quality manufacture is tough to beat when it comes to performance, be it a Sahara rally or a weekend trip. Dotz 4x4 designed this rim to be hardwearing and robust above everything else. Whenever the Dakar is released as a new vehicle, you can be sure it has undergone the most rigorous testing regime, giving you the highest quality and extreme durability. The Dotz Dakar is quickly cleaned by hand or pressure washer and due to its special finish it will be very easy on the eye for a long time – something that can’t be said of many steel rims. We are introducing the Dakar’s off-road performance and its classic look now also for the Jimny II GJ HJ and offer the rim with sizes 7x16 inches with an offset of 0 mil. A great rim needs an equally great tire and with the BFGoodrich All Terrain there’s no doubt that it’ll be up to the challenge. As a proven all-season multi-purpose tire, the latest T/A KO2 generation boasts even more improvements and better test results over its predecessor: the tire’s sidewalls are 20% more robust, durability doubles on gravel and adds another 15% on asphalt. Traction is also improved with an increase of 10% and 19% for slush/mud and snow, respectively. As far as the look is concerned the tire can be mounted with the white print to the in- or the outside. Certification documents are included. The wheel sets are available with or without spare wheel. The tire is suitable and permitted for winter use. Size:Rim 7 x 16" ET 0.0 Silver wie tire size 225/75R16*Rim 7 x 15" ET 0.0 Silver with tire size 215/65R16 * Required Modifications for 16” Wheel Set This wheel set size requires a suspension raising kit. The speedometer requires a ratio adapter. The wheel arch covers need to be adapted. Please let us know when ordering whether the white lettering is to be mounted inside or outside.
Prices incl. VAT;
Premium Long-Term Underbody and Cavity Corrosion Protection with Mike Sanders and TimeMAX for Jeep Wrangler JK Long-lasting corrosion protection for your Jeep Wrangler JK or Wrangler Unlimited JK: Using Mike Sanders Corrosion Protection Grease and TimeMAX underbody protection, our workshop team draws on 30 years of experience to protect corrosion-prone areas – both inside and out. At our specialist 4x4 workshop in Berg bei Neumarkt, Bavaria, between Nuremberg and Regensburg, we offer professional underbody and cavity corrosion protection for the Jeep Wrangler JK and Wrangler Unlimited JK, model years 2007 to 2018. This helps protect your Jeep's ladder chassis, underbody and corrosion-prone bodywork against rust, avoid costly repairs and preserve the vehicle's structural integrity over the long term. The following services are included in the complete package: Comprehensive corrosion protection: Treatment of the ladder chassis inside and out, underbody, wheel arches, axles, doors, tailgate, bonnet and other corrosion-prone areas. Professional preparation: Removal of relevant covers and trim panels to gain access to hard-to-reach areas. Extensive protective masking: Careful masking of the vehicle, particularly bodywork, painted surfaces, windows, brakes and other components that must not be treated. Mike Sanders cavity protection: Hot-spray application using specialist cavity probes for effective corrosion protection deep inside enclosed areas and long-term creeping action. TimeMAX underbody protection: Durable protective coating for the underbody surfaces to be treated. Additional corrosion protection: Further protection of selected areas using suitable products where required. Endoscopic inspection: Visual inspection of accessible cavities before and after treatment. Reassembly and cleaning: Reinstallation of removed components and final cleaning. A more detailed explanation of each service can be found below. Your benefits – and what they mean for your Jeep Wrangler JK Long-term corrosion protection: Reduces contact between metal, moisture and oxygen, helping to slow down corrosion processes. Protection from within: Protects particularly vulnerable areas inside the ladder chassis and bodywork, where rust may remain unnoticed for a long time. Long-lasting creeping action: Mike Sanders Corrosion Protection Grease continues to spread into narrow seams, gaps and overlapping panels even after application. Durable underbody protection: Helps protect treated metal surfaces against moisture, road spray, road salt and the typical demands of road and off-road driving. Complementary protection systems: Mike Sanders for cavities and TimeMAX for more heavily exposed external underbody surfaces. Professional application: Disassembly, careful masking, specialist cavity probes and endoscopic inspections enable thorough treatment. Long-term value retention: Preventative corrosion protection helps preserve the vehicle's structural integrity and avoid expensive rust damage. Our extensive experience in dealing with corrosion We have been working with off-road vehicles in our workshop for 30 years and know from first-hand experience just how serious corrosion damage can become on chassis, underbody components and concealed areas of the bodywork. Vehicles regularly driven off-road are exposed to moisture, mud, dirt and mechanical stresses that can affect their long-term condition. The Jeep Wrangler JK is no exception. Rust may develop in concealed areas and remain undetected for a considerable time. During corrosion protection treatment, we therefore pay particular attention to the ladder chassis and its cavities, joints, seams and other vulnerable areas. Protect your Wrangler in good time, before minor rust spots develop into extensive repairs – helping to ensure a long service life and preserve your vehicle's value. Comprehensive corrosion protection – protecting all relevant components For effective long-term corrosion protection, it is essential to treat not only the visible underbody but also the internal cavities. We treat the ladder chassis inside and out, the underbody, wheel arches, axles and suspension areas, as well as corrosion-prone sections of the doors, tailgate and bonnet. In the Jeep Wrangler JK, moisture and dirt can accumulate inside the ladder chassis, around chassis joints, along panel seams and within hard-to-reach body cavities. Corrosion can develop in these areas without being immediately visible from the outside. Comprehensive treatment specifically protects these vulnerable areas and helps preserve the vehicle's structural integrity over the long term. Disassembly – accessing concealed corrosion-prone areas Effective corrosion protection must also reach areas concealed by trim panels or accessories when the vehicle is fully assembled. We therefore remove relevant covers and trim panels before treatment. This provides access to important application points and areas that would otherwise be difficult to reach. It allows us to apply the protective materials precisely where they are needed rather than treating only externally visible surfaces. Protective masking – precise application without unwanted overspray Corrosion protection belongs on the intended surfaces – not on paintwork, windows or brakes. Before application, the vehicle is carefully covered and masked. Particular attention is paid to protecting bodywork, painted surfaces, windows, the braking system and other components that must not come into contact with the protective products. This extensive preparation enables controlled application and reduces the risk of unwanted contamination or interference with sensitive components. Mike Sanders Corrosion Protection Grease – lasting creeping action inside cavities The key advantage: the corrosion protection grease remains capable of creeping into narrow gaps and panel seams, even after application. Mike Sanders Corrosion Protection Grease is heated to approximately 120 °C and applied using a hot-spray process with specialist cavity probes. This allows us to introduce the material deep inside the Jeep Wrangler JK's ladder chassis and other enclosed cavities. The grease forms a protective film on the treated metal surfaces. Thanks to its temperature-dependent creeping properties, it continues to spread over time and can penetrate welded seams, overlapping panels and extremely narrow gaps. How it protects: The grease film creates a barrier between the metal, moisture and oxygen. Unlike rigid coatings, it remains flexible and can continue to provide protection even when the material expands and contracts due to temperature changes. TimeMAX underbody protection – protection against moisture, dirt and stone chips The underbody of a Jeep Wrangler JK is exposed to particularly demanding conditions, especially when the vehicle is regularly driven off-road. Stone chips, mud, dirt, road spray and road salt can damage or gradually wear away existing protective coatings. Corrosion may then begin on exposed metal surfaces. We use high-quality TimeMAX underbody protection on the external underbody surfaces to be treated. The coating forms a durable barrier against corrosion-promoting environmental influences and the typical stresses of road and off-road use. It is the combination that makes the difference: TimeMAX protects external underbody surfaces, while Mike Sanders is particularly effective inside enclosed cavities and narrow gaps. Additional corrosion protection – tailored to each area Depending on the condition of the vehicle and the area being treated, additional protective measures may be beneficial. Suitable corrosion protection products can be used in selected areas where their material properties are appropriate for the particular application. This allows the treatment to be adapted to the different requirements of the Jeep Wrangler JK's bodywork and underbody components. Endoscopic inspection – checking cavities before and after treatment Hard-to-reach areas should also be inspected – not just the visible surfaces. Before treatment, we examine accessible cavities using an endoscope. This allows us to assess the condition of internal surfaces and identify possible rust spots. Following treatment, another endoscopic visual inspection is carried out. This enables us to check the application and distribution of the corrosion protection material in the areas that can be inspected. Reassembly and cleaning – completing the treatment properly The complete package also includes professionally restoring the vehicle to its assembled condition after treatment. Once the protective materials have been applied, we remove the masking and reinstall the previously removed trim panels and components. Finally, the areas affected during the work are cleaned. This completes the comprehensive corrosion protection treatment. Vehicle condition and possible additional work The fixed package price applies to new or nearly new vehicles without heavy contamination or extensive rust damage. If more extensive cleaning or rust removal is required, the additional work will be charged separately. In such cases, we can only provide a firm price after inspecting and assessing the condition of the vehicle. Professional corrosion protection can also be worthwhile for older Jeep Wrangler JK vehicles with existing rust. By shielding treated metal surfaces from moisture and oxygen, further corrosion can be slowed down. Careful inspection and preparation of the affected areas are essential, and existing structural damage may need to be repaired beforehand. Booking an appointment and treatment duration Please note: The treatment is carried out exclusively at our workshop in 92348 Berg bei Neumarkt in der Oberpfalz, Bavaria, Germany. Our workshop is easily accessible and is located approximately 35 km from Nuremberg, 70 km from Regensburg and 145 km from Munich. The fixed-price package is available for the Jeep Wrangler JK and Jeep Wrangler Unlimited JK, model years 2007 to 2018. Please select the correct vehicle version when ordering: Jeep Wrangler JK: 2-door, short wheelbase (SWB). Jeep Wrangler Unlimited JK: 4-door, long wheelbase (LWB). Please provide your telephone number when placing your order so that we can arrange an appointment. A member of our team will contact you using the number provided to schedule your visit. Alternatively, you can contact us first on +49 9181 466 644 to arrange an appointment before ordering the service. The comprehensive treatment, including preparation, masking, corrosion protection and reassembly, normally takes 2–3 days. How Often Should the Corrosion Protection Be Inspected? Professionally applied corrosion protection provides long-term protection against rust and corrosion. Nevertheless, we recommend having the cavity and underbody protection inspected at regular intervals. How often an inspection is advisable depends primarily on how the vehicle is used and the environmental conditions it is exposed to. In particular, off-road driving, heavy road salt exposure and challenging weather conditions can place additional strain on the protective coating. Our recommended inspection intervals: Intensive off-road use (Heavy Off-Road): annually Regions with heavy road salt exposure: annually Moderate off-road use or expedition vehicles in Northern Europe: every 2–3 years Moderate off-road use or expedition vehicles in Southern Europe: every 4–6 years Predominantly on-road use: every 7–10 years During an inspection, the protective coating is checked to ensure it remains complete and intact, and to identify any areas that may require additional treatment. Regular inspections help maintain the vehicle's long-term value and allow potential corrosion issues to be addressed at an early stage.
Prices incl. VAT;
Premium Long-Term Underbody and Cavity Corrosion Protection with Mike Sanders and TimeMAX for Land Rover Defender Long-lasting corrosion protection for your Land Rover Defender: Using Mike Sanders Corrosion Protection Grease and TimeMAX underbody protection, our workshop team draws on 30 years of experience to protect known corrosion-prone areas – both inside and out. At our specialist 4x4 workshop in Berg bei Neumarkt, Bavaria, between Nuremberg and Regensburg, we offer professional underbody and cavity corrosion protection. This helps protect your Defender's chassis, underbody and corrosion-prone bodywork against rust, avoid costly repairs and preserve your Land Rover's structural integrity over the long term. The following services are included in the complete package: Comprehensive corrosion protection: Treatment of the chassis inside and out, underbody, wheel arches, axles, doors, tailgate and bonnet. Professional preparation: Removal of relevant covers and trim panels to gain access to hard-to-reach areas. Extensive protective masking: Careful masking of the entire vehicle, particularly bodywork, painted surfaces, windows, brakes and other components that must not be treated. Mike Sanders cavity protection: Hot-spray application using specialist cavity probes for effective corrosion protection deep inside enclosed areas and long-term creeping action. TimeMAX underbody protection: High-quality protective coating for the entire underbody. Normfest Protector Wax: Additional corrosion protection in selected areas. Endoscopic inspection: Visual inspection of cavities before and after treatment. Reassembly and cleaning: Reinstallation of removed components and final cleaning. A more detailed explanation of each service can be found below. Your benefits – and what they mean for your Defender Long-term corrosion protection: Reduces contact between metal, moisture and oxygen, helping to slow down corrosion processes. Protection from within: Protects particularly vulnerable areas inside the chassis and bodywork, where rust often develops unnoticed for a long time. Long-lasting creeping action: Mike Sanders grease continues to reach narrow seams and gaps even after application, supplementing the original protective coating. Durable underbody protection: Reduces the impact of typical environmental conditions on treated metal surfaces. Three premium branded products: Different protective materials are combined according to their specific areas of application. Professional application: Disassembly, masking, specialist cavity probes and endoscopic inspections enable thorough treatment. Long-term value retention: Preventative corrosion protection helps preserve the vehicle's structural integrity and avoid expensive rust damage. Our extensive experience in dealing with corrosion We have been servicing and repairing Land Rover Defenders for 30 years and know from first-hand experience just how serious rust damage can become, particularly in concealed areas of the chassis and underbody. We are familiar with the typical weak points and understand what effective corrosion protection requires. Protect your Defender in good time, before minor rust spots develop into expensive repairs – helping to ensure a long service life and preserve your vehicle's value. Comprehensive corrosion protection – protecting all relevant components For effective long-term corrosion protection, it is essential to treat not only the visible underbody but also the internal cavities. We treat the ladder chassis inside and out, the underbody, wheel arches, axles and corrosion-prone areas of the doors, tailgate and bonnet. Moisture can accumulate inside the ladder chassis, along panel seams and in hard-to-reach body cavities. Rust often develops unnoticed in these areas, spreading from the inside out. Comprehensive treatment specifically protects these vulnerable areas and helps preserve the vehicle's structural integrity over the long term. Disassembly – accessing concealed corrosion-prone areas Effective corrosion protection must also reach areas that are concealed when the vehicle is fully assembled. We therefore remove relevant covers and trim panels before treatment. This provides access to important application points and areas that would otherwise be difficult to reach. It allows us to apply the protective materials precisely where they are needed, rather than treating only externally visible surfaces. Protective masking – precise application without unwanted overspray Corrosion protection belongs on the intended surfaces – not on paintwork, windows or brakes. Before application, the entire vehicle is carefully covered and masked. Particular attention is paid to protecting bodywork, painted surfaces, windows, the braking system and other components that must not come into contact with the protective products. This extensive preparation enables controlled application and prevents unwanted contamination or interference with sensitive components. Mike Sanders Corrosion Protection Grease – lasting creeping action inside cavities The key advantage: the corrosion protection grease remains capable of creeping into narrow gaps and panel seams, even after application. Mike Sanders Corrosion Protection Grease is heated to approximately 120 °C and applied using a hot-spray process with specialist cavity probes. This allows us to introduce the material deep inside the ladder chassis and other vehicle cavities. The grease forms a protective film on the treated metal surfaces. Thanks to its temperature-dependent creeping properties, it continues to spread over time and can penetrate welded seams, overlapping panels and extremely narrow gaps. How it protects: The grease film creates a barrier between the metal, moisture and oxygen. Unlike rigid coatings, it remains flexible and can continue to provide protection even when the material expands and contracts due to temperature changes. TimeMAX underbody protection – protection against moisture, dirt and stone chips The underbody is exposed to particularly demanding conditions and therefore requires a suitably durable protective coating. Stone chips, dirt, road spray and road salt can damage or gradually wear away the factory-applied protective coating. Corrosion can then begin on exposed metal surfaces. We use high-quality TimeMAX underbody protection across the entire underbody area to be treated. The coating forms a protective barrier against corrosion-promoting environmental influences and the typical stresses of both road and off-road driving. It is the combination that makes the difference: TimeMAX protects the external underbody surfaces, while Mike Sanders is particularly effective inside enclosed cavities and narrow gaps. Normfest Protector Wax – additional protection in selected areas We also use Normfest Protector Wax in selected areas to complement the overall corrosion protection treatment. This corrosion protection wax offers good wetting and creeping properties. Once dry, it forms a flexible, firmly adhering protective film on the treated metal surfaces. It is applied wherever its material properties are particularly suitable for the specific area. In this way, the different protection systems complement one another to create a corrosion protection treatment tailored to the vehicle. Endoscopic inspection – checking cavities before and after treatment Hard-to-reach areas should also be inspected – not just the visible surfaces. Before treatment, we examine accessible cavities using an endoscope. This allows us to assess the condition of internal surfaces and identify possible rust spots. Following treatment, another endoscopic visual inspection is carried out. This enables us to check the application and distribution of the corrosion protection material in the areas that can be inspected. Reassembly and cleaning – completing the treatment properly The complete package also includes professionally restoring the vehicle to its assembled condition after treatment. Once the protective materials have been applied, we remove the masking and reinstall the previously removed trim panels and components. Finally, the areas affected during the work are cleaned. This completes the comprehensive corrosion protection treatment. Vehicle condition and possible additional work The fixed package price applies to new or nearly new vehicles without heavy contamination or extensive rust damage. If more extensive cleaning or rust removal is required, the additional work will be charged separately. In such cases, we can only provide a firm price after inspecting and assessing the condition of the vehicle. Mike Sanders treatment can also be worthwhile for older vehicles with existing rust. Further corrosion can be stopped by shielding the affected metal surfaces from oxygen, provided that the corroded areas are completely covered and sufficiently sealed by the protective material. Careful preparation of the affected areas is essential. Booking an appointment and treatment duration Please note: The treatment is carried out exclusively at our workshop in 92348 Berg bei Neumarkt in der Oberpfalz, Bavaria, Germany. Our workshop is easily accessible and is located approximately 35 km from Nuremberg, 70 km from Regensburg and 145 km from Munich. When placing your order, please select the wheelbase of your Land Rover Defender and provide your telephone number so that we can arrange an appointment. A member of our team will contact you using the telephone number provided to schedule your visit. Alternatively, you can contact us first on +49 9181 466 644 to arrange an appointment before ordering the service. The extensive treatment of the entire underbody, including the comprehensive masking required to protect the rest of the vehicle from overspray, normally takes 2–3 days. How Often Should the Corrosion Protection Be Inspected? Professionally applied corrosion protection provides long-term protection against rust and corrosion. Nevertheless, we recommend having the cavity and underbody protection inspected at regular intervals. How often an inspection is advisable depends primarily on how the vehicle is used and the environmental conditions it is exposed to. In particular, off-road driving, heavy road salt exposure and challenging weather conditions can place additional strain on the protective coating. Our recommended inspection intervals: Intensive off-road use (Heavy Off-Road): annually Regions with heavy road salt exposure: annually Moderate off-road use or expedition vehicles in Northern Europe: every 2–3 years Moderate off-road use or expedition vehicles in Southern Europe: every 4–6 years Predominantly on-road use: every 7–10 years During an inspection, the protective coating is checked to ensure it remains complete and intact, and to identify any areas that may require additional treatment. Regular inspections help maintain the vehicle's long-term value and allow potential corrosion issues to be addressed at an early stage.
Prices incl. VAT;
Mobile parking heater without battery and in aluminium box You can find information on hire equipment below. “It's a Thin Line Between Love and Hate” is the old song and this thin line between loving and hating the same thing is definitely the line on the thermometer in winter. If you freeze off the part of your body with an A, you're guaranteed not to enjoy even the fattest fish at the ice hole, the most magical aurora borealis or the greatest fun at the elephant meeting. That's why we have our solution for all outdoor activities in the cold seasons in the Alubox Pro: the AUTOTERM parking heater for on the go! With the exception of the battery, everything you, your family or your crew need for a warm and cozy outdoor feeling in your car, camper or roof tent is in the ultra-robust, waterproof 29L box. At its heart is the affordable and powerful AUTOTERM (Planar) 2D12 air heater, which can be powered from the vehicle battery via the cigarette lighter adapter. It is controlled via the PU5 control element. A 5.4 l fuel tank is already integrated in the box. This makes our mini heater ideal for on the road and mobile use on the vehicle or wherever a weatherproof cable connection to a car battery can be established. The warm air is transported into the room to be heated via a firmly screw-fastened, waterproof Flexi hose, which can be ordered separately in the desired length here in the store. ATTENTION: As a precaution, we would like to point out that operation in closed rooms is not permitted due to the risk of poisoning from exhaust fumes. Furthermore, for optimum heating performance, care should be taken to ensure that the air inlets for combustion and hot air are positioned so that they are protected from the weather. You can find the perfect storage bag for the Flexi hose here in the store.A larger standalone version of this parking heater with integrated battery is available here. You can also hire this parking heater from us. Alu-Box Pro (29 liters) waterproof/dustproof according to IP54 standard AUTOTERM (Planar) 2D diesel / air heater ✔ Fuel tank (5.4 liters)✔ Hot air pipe connection, non-return valve, outlet and inlet feed-through✔ Including radio remote control✔ The openings for supply and exhaust air and for the power supply are splash-proof (can be closed with a screw cap or rubber plug)Dimensions of the aluminum box: WxHxD 390x340x290mmDimensions of the box with spigot: WxHxD 490x340x290Total weight: 11.2 kgTechnical data of the parking heater:- Fuel type: Diesel- Heating output: max. 1.8kW, min. 0.8kW- Volume of heated air: max. 75m³/h, min. 34m³/h- Fuel consumption during operation: max. 0.24l/h, min. 0.1 l/h- Power consumption during operation: max. 29W, min. 10W- Manual start/stop- Connection to a car battery or another external 12V battery PU-5 control element: - LED for ventilation display- LED for operating display- Temperature adjustable via rotary control The AUTOTERM Air 2D (Planar 2D) is equipped with an altitude kit! This means that the heater automatically reduces the injection volume according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content falls. The maximum heat output decreases in proportion to the amount of oxygen in the air. Roughly speaking, from 2000 meters upwards, the loss of output per 500m altitude is approx. 5%. Manufacturer tests up to 3440m were problem-free. No problems are to be expected up to 4000m. Up to 5000m the software calculates itself - but this could not yet be tested at real altitude. Please note: Most portable power stations or battery boxes (such as Goal Zero, Eco Flow, Bluetti etc.) are unfortunately not suitable for operating the mobile parking heaters.The heater requires up to 15A as starting current and when shutting down, but very few battery boxes can provide this..In general, however, direct connection to the battery terminals is the best solution If you want to heat the interior of your vehicle, we offer an installation service for warm air ducting through a ventilation plate. Please note the legal information on batteries HERE. For certain types of batteries, we are legally obliged to charge a deposit. EQUIPMENT HIRE: Hire an Small independent mobile heating system w/o battery Click here to make a no-obligation enquiry! Rental rates 1 week(7 days) 2 week(14 days) 3 week(21 days) 4 week(30 days) AUTOTERM 2D12 in Alubox without Batterie 287€ 382€ 438€ 478€ Prices include VAT PLEASE NOTE: As a precaution, we would like to point out that the appliance must not be used in enclosed spaces due to the risk of poisoning from exhaust fumes. Furthermore, to ensure optimum heating performance, please ensure that the air intakes for combustion and hot air are positioned in a way that protects them from the weather. Our hire heaters are delivered in wooden crates. The diesel tank is empty on delivery and MUST also be empty when returned!
Prices incl. VAT;
Standard main beam headlights do the job as long as the road runs straight to the supermarket. Once the tarmac ends, everything left and right of the track goes dark fast. And from that point on, the terrain tends to keep surprises ready, for example a deer that doesn't see the off-roader coming, or a road edge that suddenly drops away into a deep ditch. The Vision X CG2 CPM710 Light Cannon make those surprises visible: multi-LED driving lights for the Ineos Grenadier, built for short and medium range. The beam of the Vision X auxiliary driving lights for the Grenadier Each lamp holds seven LEDs of 7 watts each, every one with its own 10° optic, and together they produce a wide driving beam. That works out to 49 watts per lamp, so 98 watts as a pair. Colour temperature sits at 6,000 Kelvin, which gives the light a clear, neutral-white character. Anyone looking for range rather than width should take a look at the single-LED sibling, the Vision X CG2 CPZ110. Clear or yellow lens? The Vision X auxiliary driving lights for the Grenadier come with either a clear or a selective yellow lens. Clear delivers the full light output and is the standard choice for clear nights. The yellow version is built for the days when something is hanging in the air, like dust on a desert track, mist in the mountains, driven snow on a pass, or heavy rain in the forest. Yellow light scatters less on particles in the air and therefore does not build the blinding wall in front of the bonnet that clear light can throw up when visibility drops. Housing waterproof and tough The housing of the CG2 CPM710 is a hybrid of aluminium and polycarbonate, tough enough for stone chips and light enough for the grille. The lens is acrylic, and together the lamps are IP68 waterproof and IP69K pressure-washer tested, stand up to 21.2 Grms of vibration, and operate between minus 40 and plus 80 degrees Celsius. The LEDs are rated for around 50,000 hours. Fitment in the grille, no drilling Vision X developed this kit specifically for the Ineos Grenadier and tested it on the vehicle in Europe. The lamps sit neatly in the grille with the supplied brackets, with no drilling or cutting required, so parking sensors and driver assistance systems stay fully functional. The plug-and-play wiring loom brings everything needed, including relay, fuses, and a CAN-bus connection, so the driving lights switch on automatically or manually together with the main beam. Anyone who wants to revert to the original setup can do so at any time. Technical specification Dimensions (L × W × H): 14.5 cm × 9.4 cm × 13.4 cm Manufacturer: Vision X LED type: 7 × 7 W LEDs, each with 10° optic (multi-LED) Power: 2 × 49 W (98 W as a pair) Luminous flux: 10,500 lumens total Range: approx. 215 m Beam type: wide driving beam Colour temperature: 6,000 K Lens: acrylic, clear or selective yellow Input voltage: 9 to 32 V DC Current draw: 4.08 A per lamp at 12 V (8.17 A as a pair), 2.04 A at 24 V Weight: 1.3 kg per lamp Housing: hybrid (aluminium and polycarbonate) Protection rating: IP68 waterproof, IP69K pressure-washer tested Vibration rating: 21.2 Grms Operating temperature: −40 °C to +80 °C Lifespan: around 50,000 hours Certifications: CE, RoHS, IEC 62471, ECE R112 (driving lamp) Connector: Deutsch connector In the box: 2 driving lights with connection cable
Prices incl. VAT;
Set of 4 AEZ Panama aluminium rims for the Land Rover New Defender The AEZ Panama combines a striking cross-spoke design with impressive stability, making it the ideal choice for demanding off-road adventures as well as for a stylish appearance on the road. With a load capacity of up to 1,025 kg, this rim is perfectly designed to meet the high demands of modern SUVs – especially the Land Rover New Defender. Technical details: Size: 8.5x20" Offset (ET): 38 mm Colours: silver or black Bolt circle: 5x120 Load capacity: up to 1,025 kg The AEZ Panama impresses with its high-quality workmanship, maximum robustness and a design that perfectly underlines the powerful character of the New Defender. Ideal for anyone who wants to give their vehicle a high-quality, elegant and at the same time durable upgrade.
Prices incl. VAT;
The XPL Curved Lightbar is an extremely powerful installation solution for the slot of the standard radiator grille Installing work lamps, additional headlights or light bars on your vehicle is not too difficult – when you’re talking older pickups or classic Defenders, that is. Obviously, with newer cars like the New Defender one should be a lot more cautious before drilling holes or attaching brackets to the expensive exterior. Vision X Lighting specialize in custom solutions, combining top performance, sleek design and installation methods that minimize effort and actual alterations to your car. The XPL Curved Lightbar by Vision X is an elegant and powerful LED solution for the lower opening in the standard grille of the New Defender. The array of individual 5 W CREE LEDs delivers a light beam of over 600 m – providing safety in all weather conditions, off-road or on-road, for work or sports. The XPL Curved lightbar also features backlighting that can be used as daytime running lights. The installation is fairly simple and requires roughly 4 hrs. Both the grille’s plastic substructure and the lower opening need to be modified by sawing out specific areas. Detailed instructions, fastening materials and electric connections are included in the delivery. Mounting behind the radiator grille is also possible. Specifications for XPL Curved Lightbar: LEDs: 5W per LED Housing material: aluminium Light colour temperature: 6000 Kelvin Voltage: 9-32V DC Current: 3.12A~8.96A@24V DC - 6.25A~17.92A@12V DC Vibration resistance: 21 Grms Lens material: Polycarbonate Smooth backlight Proprietary IRIS reflector technology Curved high power light bars Weatherproof Deutsch connector with plug-and-play wiring harness Certifications: CE, RoHS, IEC 62471, ECE R112 Thanks to our iris reflector technology and the unique curve of the bar, the XPL Curved series produces a wide spot beam pattern with a range of over 600 metres. Scope of delivery: Complete radiator grille set for New Defender with XPL-HC23 light bar, brackets and wiring harness including detailed installation instructions.
Prices incl. VAT;
Complete set of AUTOTERM Air 2D parking heater for Defender The parking heater set AUTOTERM (Planar) 2D12 for the Land Rover Defender consists of all important components needed for the installation of a parking heater. Included in the delivery are the AUTOTERM 2D 12 Volt parking heater, our Nakatanenga parking heater console, the Nakatanenga mounting plate, a fuel tank extraction, a Webasto air outlet with 60 mm connection, 30 cm warm air pipe and a vibration damper.As a low-priced and powerful alternative to our Webasto parking heater kits, the AUTOTERM (=Planar) 2D parking heater is proving to be a real sales hit. This is partly due to the particularly compact dimensions, which allow installation even in small cars, vans, off-roader motorhomes, construction machinery, boats or in difficult installation situations. In the off-road / 4x4 sector, it is ideally suited for the "typical" off-road vehicles such as Land Rover Defender, Mercedes G or Jeep Wrangler JK.These are only a few of many reasons why we now offer the AUTOTERM (Planar) 2D 12 V parking heater in a clear and comprehensive complete set for the Land Rover Defender at an economical price. For both the Tdi/ Td5 and the Td4, we offer one set each with a perfectly matching accessory kit.You can select different front panel cut-outs for the parking heater console included in the scope of delivery. The associated connections are available in the classic cigarette lighter format (12 V) or as 5 V USB charging sockets for Apple iPhones, navigation devices, iPads and smartphones and are included in the scope of delivery.The parking heater can also be operated while driving.Running time: The AUTOTERM parking heater switches off automatically after 2 hours of operation. However, as soon as you press a button during operation, the parking heater continues to run indefinitely until it is switched off manually.Scope of delivery:- AUTOTERM 2D parking heater 12 volt incl. silencer, intake air hose, heat protection hose, tank intake pipe and corrugated exhaust pipe.- Optionally analogue control unit simple control (PU-5) with rotary control or digital control unit comfort control (PU-29) with time switch- Nakatanenga parking heater console incl. the selected connections- Nakatanenga mounting plate- Fuel filler cap- Webasto air outlet with 60 mm connection, rotatable- 30 cm warm air pipe (diameter: 60 mm)- Vibration damper- Fixing material (screws, nuts, clamps, shrink hose, cable ties)Technical data:- Fuel type: diesel- Heating capacity: max. 1.8 kW, min. 0.8 kW- Volume of heated air: max. 75 m³/h, min. 34 m³/h- Fuel consumption in operation: max. 0.24 l/h, min. 0.1 l/h- Power consumption in operation: max. 29 W, min. 10 W- Weight: 3 kg (independent heater)- Manual start/stop → On the Autoterm.cz site you will find a calculator for the correct dimensioning of the air heater,You can choose between two control elements:- Simple Control (PU-5) element with rotary control: The old PU-10 control element had a relatively inaccessible control surface. Therefore, the reliable control element with rotary control is now the new improved standard of the Planar parking heaters! With the rotary control, you can adjust the heating power of the parking heater and regulate the power of the ventilation in ventilation mode! The PU-5 control element with rotary control can also be purchased separately here.- The digital control element comfort control (PU-29) with timer has an OLED display and an understandable and clear interface. Temperature, ventilation and power can be configured via the display and the various buttons. With the timer, you can easily set the start of the parking heater to a specific time. The digital control element with timer can also be purchased separately here.Setting options comfort control (PU-29):- Temperature and power (adjustable for the parking heater, the control panel and for an external heater).- Time and date - Operating language (English or Russian)Functions of the timer comfort control (PU-29):- Memory function: save the time so that the parking heater starts at this time every day - Configurable memory locations: Up to 3 different weekdays with different times can be set and saved. The AUTOTERM (=Planar) 2D12 is equipped with an altitude kit.This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heat output decreases proportionally to the amount of oxygen in the air. Roughly speaking, from 2,000 metres the loss of output per 500 m altitude is approx. 5%. Manufacturer tests up to 3,440 m were trouble-free. Up to 4,000 m no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not yet be tested at real altitude. Important:Especially when used at high altitude, the free travel of the fan is extremely important!Route the combustion air intake and exhaust extremely short and with low resistance - i.e. no kinks, no blockage or reduction. It should also be noted that operation beyond 3,000 m is still a technical compromise. Again, care should be taken to ensure that the combustion chamber is properly heated on a regular basis. The chamber must be burnt free of soot deposits. Soot deposits can also form on heaters that are permanently operated at the lowest setting. Therefore, the following still applies: No guarantee for sooty combustion chambers!In order to ensure the longevity of the heater, you should also free-burn it occasionally at low levels. The combustion chamber reaches full temperature after running at full load for about half an hour. Normally, no further maintenance is required. In case of extreme loads, e.g. during longer overnight stays at more than 4,000 m, the combustion chamber including the seal set should be cleaned if necessary. To heat your roof tent using your auxiliary heating system, we offer an installation service for a warm air duct through a ventilation plate. https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment
Prices incl. VAT;
Cannon Race CR-7 - 70 Watt - SPOT BEAM DRIVING LIGHT Ultra-Bright 15.330 Raw Lumens Per Pair Broad Spot Beam Pattern with 458m of Distance and 60m. Wide SAE/DOT & ECE Approved Clear and Selective Yellow Lens Options Shatterproof Polycarbonate Lens The Cannon Race Series 7 LED (CR-7) delivers the highest performing spot beam to hit the market. The CR-7 utilizes a truly unique lens that performs as well as it looks. With a broad spot beam that reaches 458m long and 60m wide, the CR-7 outperforms and outshines the competition with ease.The CR-7 utilizes only top-binned 10W LEDs from CREE that allows the CR-7 to blasts a massive 15.330 lumens (pair) out of only a 114mm housing. Never let dust, fog or rain slow you down again. The selective yellow lens will allow your CR-7 to cut through any tough weather while maintaining maximum output.Virtually unbreakable, the CR-7 uses a powerful polycarbonate bezel that won't crack, fade or corrode like traditional aluminum bezels. Ready for the most extreme environments the CR-7's are submersible and watertight with a IP68/69K housing that is capable of withstanding any adventure you can throw at it. Features: LEDs: 7 x 10W Housing Material: aluminum Light Colour Temp: 5600 Kelvin Dimensions: 114/121/74mm Weight: 0.62 kg Voltage: 9-32V DC Amperage: 2.92A@24V DC - 5.84@12V DC Vibration Rating: 21.2 Grms Lens Material: Polycarbonate Certifications: CE, RoHS, ECE R112 Weatherproof Deutsch Connector
Prices incl. VAT;
Nolden 7-inch Gen 2 Bi-LED Headlights: Illuminate the night and give your Defender the ultimate look! Now also available in All-Black = Stealth Edition! Do you love your Land Rover Defender, but the original headlights let you down in the dark or bad weather? Then it's time for an upgrade that not only provides brilliant illumination but also gives your off-road classic a modern and premium touch: the Nolden 7-inch Generation 2 Bi-LED Reflector Headlights! More light, more safety, more style – for your Defender: These high-end headlights are the result of German engineering and set standards in terms of light output, durability, and design. Say goodbye to dim halogen light and experience the road and terrain ahead in a whole new clarity. Brilliant Bi-LED Technology: Experience significantly brighter and more uniform illumination than with conventional headlights. The Bi-LED function combines low beam and high beam in one module, ensuring a seamless transition and impressive range. This means for you: You see obstacles earlier and drive safer – whether on a dark country road or in the deepest terrain. Plug & Play Installation: Developed as a direct replacement for your Defender's original 7-inch headlights. Installation is straightforward and requires no complex vehicle modifications. Extremely durable and maintenance-free: LED technology is not only more energy-efficient but also significantly more durable than halogen lamps. No more annoying bulb changes! These headlights are built to withstand the harsh conditions your Defender is exposed to. Modern look with a classic touch: The Nolden headlights blend perfectly with the Defender's iconic design while giving it a modern, high-quality appearance. The clear lens and thoughtful reflector design make them a real eye-catcher. (Depending on the chosen variant, e.g., in Chrome, you further enhance the premium look). With E-certification mark – road legal: Naturally, these premium headlights have the necessary E-certification, so you can drive legally and without concerns on public roads. Features at a glance: State-of-the-art Nolden LED low beam and high beam, LED daytime running light, and position light in fiber optic technology Significantly improved light output and visibility Perfect fit for Land Rover Defender (replaces original 7-inch headlights) Long lifespan and high energy efficiency Weather-resistant and robust Elegant design that enhances your Defender With E-certification mark for legal road use Treat your loyal companion to the light upgrade it deserves! With the Nolden 7-inch Generation 2 Bi-LED Headlights, you invest in safety, durability, and an unbeatable look. Turn night into day and enjoy every drive with perfect visibility! A few more details: Over 30,000 hours LED lifespan White road illumination, similar to Xenon H4 connectors for Plug & Play Standard 7” mounting (PAR56) Die-cast aluminum housing 480 h salt spray test Available in Chrome, Dark-Chrome, Matte-Black, and All-Black Approvals: ECE and EMC Technical Data: Low beam: 23 W High beam: 33 W Daytime running light: 8.5 W (fiber optic) Position light: 1.2 W (fiber optic) Dimensions: 177 mm LED Type: OSRAM Voltage: 12/24 V Weight: 880 g Tested: ECE, EMC Ventilation: Nitto Denko Air Cap Housing material: Diallyl Diglycol Carbonate (ADC) Lens material: Hardened PC (Polycarbonate) Temperature range: -40°C to +80°C Vehicle wiring: FLRY Connector: H4 for main headlight, Tyco/AMP Superseal for position light Reference number: 12.5 The Nolden LED headlights are available in Chrome, Dark-Chrome, and Matte-Black and are delivered with a cable set for position and daytime running lights. The set includes 2 headlights and 2 stainless steel mounting rings. Should you also want to replace the mounting kit during the headlight change, we have the following products for you: Fitting Kit Headlight Land Rover Defender Fitting Kit Headlight Land Rover Defender, stainless steel
Prices incl. VAT;
Powerful light, easy installation – Vision-X GEN2 Cannon LED Bring light to unexplored territories with this headlamp! HYBRID ALUMINUM-POLYCARBONATE HOUSING The Light Cannon features a housing made of both aluminum for increased strength and polycarbonate for weight reduction. UNIVERSAL MOUNTING WITH ONE SCREW Designed for easy installation, the LED Light Cannon features a sturdy, single-screw universal mounting system. STANDARD FORM FACTOR The Light Cannon LED combines the benefits of LED lighting, including low power consumption and 50,000 hour life, with the standard form factor of a conventional HID or halogen lamp. Specifications: Range approx. 350m ECE R112 approval as a driving lamp LEDs: 1 x 40W Housing material: Hybrid Color temperature: 6.000 Kelvin dimensions: 121,6 / 134 / 93,7 mm Weight of one headlamp: 0.91 kg Voltage: 9-32 V DC Current rating: 1.67A@24V DC - 3.33A@12V DC Vibration Rating: 21.2 Grms Lens material: acrylic Certifications: CE, RoHS, IEC 62471 IP68 / IP69K
Prices incl. VAT;
Door seal sets for Land Rover Defender - Perfect fit & robust for any terrain Whether replacing classic standard equipment or retrofitting for better sealing: Our selection of door seal sets for the Land Rover Defender offers the right solution for almost every model and year of manufacture. The high-quality seals (original or replica) ensure noticeably less wind noise, reliable protection against water and dust - particularly important for off-road driving or daily use in all weather conditions. Choose from different sets for driver and passenger doors, rear doors and side doors - all custom-fit, durable and easy to fit. More comfort. Less noise. Better sealing. Make your Defender fit for every adventure - with the right door seals from our range.
Prices incl. VAT;
Increased brightness for long-distance and close-range illumination Especially when driving on country roads and unpaved paths, increased visibility can be an important safety factor. The LEDriving® Functional Series FX Gen 2 portfolio provides additional close-range and far-field illumination on dark roads. Even in poor visibility conditions or at dusk, the high-performance LEDs achieve a range of up to 635 metres and daylight conditions with a colour temperature of 6000 Kelvin. The auxiliary headlamps of the FX series impress with a special reflector design and not only provide a modern and appealing look, but also reduce glare for more visibility in road traffic. They can be used both as additional LED headlights and as powerful worklights. Both versions of the lights are fully ECE-compliant and therefore suitable for use in road traffic. In addition, OSRAM has developed a special mounting kit that is compatible with all auxiliary headlamps of the FX Gen 2 series for individual mounting. Versatile in use, they defy numerous environmental influences and are particularly light and at the same time robust and resistant thanks to high-quality materials such as the aluminium housing and the stable polycarbonate lens. Complete reverse polarity protection prevents damage due to overvoltage and contributes to a longer service life. The FX series auxiliary lights have been tested and validated in a DIN-certified environmental simulation laboratory for extreme external influences with regard to water, dust, shock, heat, cold and permanent vibration in accordance with the highest IP & IK protection classes IP6K8 & IP6K9K. Their variability gives the FX series a flexible range of applications. They can be fitted to cars, trucks, agricultural machinery, commercial vehicles, construction vehicles, caravans, off-road vehicles and quads. OSRAM provides a 5-year warranty on these products. Product details:OSRAM LEDriving® auxiliary headlamp Lightbar FX1250-CB SM GEN 2 | LEDDL134-CB SM Features: COMBO BEAM = Combined beam characteristics for both far-field and near-field illumination. Light beam of 630mLuminous flux: 11,000lm, rated power: 176W Cold white light with 6000K For 12V & 24V vehicles DTP04-2P, DTP06-2S connector, cable length: 1200mm Over- and undervoltage protection Single mount certified1) (2x ECE R149), ECE R10, ECE (Ref. 2x 50). Highest protection classes: IP6K8 & IP6K9K Robust and durable - shatterproof polycarbonate lens and die-cast aluminium housing with special black coating Efficient reflector design with 45 OSRAM high-power LEDs Side brackets included 5-year OSRAM guarantee 1) Product description: Outstanding illumination, performance, quality, form, durability and functionality. Maximum optical efficiency, effectiveness and homogeneous light distribution Coverage of far-field illumination Perfectly matched to individual requirements and needs for multivariant use Special reflector design for an attractive and modern appearance and reduced glare Robust and resistant - for a long service life Increased safety off-road and on-road ECE-compliant and approved for use in road traffic Fields of application: Cars, trucks, 4x4s, ATVs, agricultural vehicles, commercial vehicles, construction vehicles, quads, caravans, etc.1) Exact conditions at: www.osram.de/am-garantieNote: Single mount - no installation in pairs necessary, as two certified light sources are used.
Prices incl. VAT;
NOLDEN LED high beam headlights, 70mm Set of 2, with E-mark, for installation Technical data: Dimensions: 69.2x55 mm LED: 1x LED 13 W Fastening: 2x M6 Approval: ECE (E-mark) Material: Aluminum Color: Black or chrome - please select.
Prices incl. VAT;
Alloy wheel for Suzuki Jimny 2 GJ/HJ High Peak J-02, 6x15" offset: -5 After the great response to the J-01 wheel, we wanted to do something different with the second original design. We present you the HIGH PEAK J-02 15-inch alloy wheel, front. While the J-01 offers a classic design with a deep lip, the J-02 features a concave seven-spoke design reminiscent of off-road motorsport. Specifically designed for the Suzuki Jimny JB74 (2018+, designated as 'GJ' & 'HJ' in the EU). TÜV type approved and strength tested. Also compatible with JB43 (1998-2018) models. Made in Italy. Guaranteed European quality Bolt-on mounting with standard or raised chassis. No additional modifications required (depending on tyre size). Rim size : 6x15"OFFSET : -5Bore / PCD : 5x139.7Finish : anthracite or vintage whiteWeight : 9.2kgVehicle : Suzuki Jimny II GJ/HJ If you need a complete wheel set, please contact us by e-mail or phone.info@nakatanenga.de☎ +49 9181 466 644
Prices incl. VAT;
Oberland Arms TitanSepp Integral TiBronze The Oberland Arms TitanSepp, designed by renowned Italian knife designer Tommaso Rumici, has become a true classic after more than 11 years in production. With the new Integral version, this proven concept reaches an even higher level in terms of material, craftsmanship and design. The new TitanSepp knives are manufactured by premium knife maker Lionsteel in Maniago, Italy – using state-of-the-art machinery combined with the expertise of highly skilled craftsmen. The standout feature of the new version is the one-piece integral handle, precision-milled from solid titanium or aluminium and available in two colour variants each. This places the new TitanSepp firmly in the premium class when it comes to quality, design, materials and finish. All knives come as standard with a MOLLE-compatible nylon knife pouch. The pouch is manufactured by TacticalBear in Germany and impresses with its robust construction and versatile usability – for example, it can also be used as a magazine pouch or accessory pouch. Our Knife Secure retention system is available separately as the perfect matching accessory. Legal certainty through BKA classification As one of the few knives on the market, the TitanSepp offers additional legal certainty through an official classification notice issued by the German Federal Criminal Police Office, the BKA. This document can be conveniently downloaded via the discreet QR code laser-engraved on the handle scale. According to the BKA classification notice, the TitanSepp knives are not classified as weapons, but as true two-hand opening knives in accordance with §42a paragraph 1, §1/2/2-a-, §1/2/2-b- and §2/3 of the German Weapons Act. You can find the BKA notice under the ‘Documents to download’ tab. For the export market, as well as for authorised use in Germany, a one-hand opening version of the TitanSepp will also be available soon. Details / Features / Specifications Blade length: 93 mm / 3.5 mm Steel: M390, black PVD, stonewashed blade Handle material: titanium, bronze PVD Handle dimensions: 125 mm / 12 mm Weight: 172 g Concept / original design: Matthias Hainich Design: Tommaso Rumici Manufacturing: Lionsteel, Maniago, Italy Accessories: includes MOLLE-compatible nylon knife pouch, manufactured by TacticalBear in Germany BKA classification notice: QR code discreetly engraved on the handle scale, included at no extra cost Serial number: each knife is marked with an individual consecutive serial number
Prices incl. VAT;
Vision-X Expora spotlights Explora by Vision X LED auxiliary lights are the next generation of driving lights developed by Vision X for Explora, which are brighter, better and easier than ever to illuminate the surroundings. The Explora series combines Vision X high quality with efficient LED diodes – to deliver driving light at an unbeatable price! With the Explora by Vision X LED driving lights, you no longer have to choose between a long or wide light pattern. Explora has unique reflectors, which provide a hybrid light beam, with both length and width, without any dark spots. Explora by Vision X is an LED driving light with outstanding performance. All models of Explora are E-marked, with Vision X E-boost. With E-boost, you can selectively increase the power of the LED diodes, for additional brightness. But even without E-boost, the Vision X Explora delivers a powerful light with length and width. The Vision X Explora series is offered as both LED driving lights and LED light bars. What they all have in common is that they are incredibly durable – with lamp housings made of high-quality aluminum and lenses made of almost unbreakable polycarbonate. The driving lights and light bars all have brackets in super strong and durable composite to resist corrosion. Explora by Vision X is of course also dust and water resistant, with full IP68/IP69K rating. The entire Explora series meets the standards ECE R10, ECE R148 and ECE R149. Last but not least, Explora by Vision X are incredibly easy to mount and install. These LED driving lights have a built-in smart control unit, so they only need to be connected to a power source and setup with clearly color-coded cables to the correct function. Vision X Explora LED driving lights include wiring, nuts and brackets for installation. The driving lights also include a cover, which is easily mounted/removed when needed. Properties: Unique reflectors that provide both width and length of the light E-marked driving lights with E-boost for extra effect Tasteful white or orange position light High durability with IP68/IP69K rating General data: Estimated LED life: 50,000 hours Colour temperature: 5700K Light pattern: hybrid (length + width) Voltage: DC11-32V Lens: polycarbonate Lamp housing: aircraft aluminium Bracket: composite IP class: IP68/IP69K Vibration class: 6.9 gRMS Operating temperature: from -40°C to +60°C Certifications: ECE R10, ECE R148, ECE R149, CE, UKCA, RoHS, REACH E-marked: Yes Daten 7 Zoll 120W 9 Zoll 200W Watt: 120W 200W E-amplifier: 80W 130W Raw lumen: 8160 lm 13600 lm Effective lumen: 6000 lm 9700 lm LED: 24 x 5W 40 x 5W Light length: 386 m @ 1 Lux (460 m in pair) 480 m @ 1 Lux (700 m im in pair) Light width: 40 m @ 1 Lux (45 m in pair) 50 m @ 1 Lux (60 m in pair) Power consumption: 5,8A @ 13,5V 9,6A @ 13,5V Width: 186 mm 221 mm Height: 186 mm 225 mm Depth: 85 mm 102 mm Weight: 2 kg 3 kg
Prices incl. VAT;
Heater and Blower Control Unit for Land Rover Defender Td4 When the blower slider stops working: complete control unit as a direct replacement The heater and ventilation controls in the Defender are used regularly over many years – and often not exactly gently. One well-known weak point of the control unit is the slider used to adjust the blower speed. As the vehicle gets older, this slider can become stiff, develop excessive play or fail completely. If the slider is faulty, the desired blower setting – particularly the middle speeds, in our experience – can no longer be selected reliably. This is especially frustrating when the windows are misted up, during winter or in poor weather conditions. With this complete heater and blower control unit, you can replace the faulty unit and restore reliable operation of the heating and ventilation system. The benefits: Complete heater and ventilation control unit Ideal replacement for a faulty or stiff blower speed slider Controls blower speed, temperature and air distribution Direct replacement for the existing control unit Suitable for: Land Rover Defender L316 Defender Td4 2.4: 2007–2011 Defender Td4 2.2: 2012–2016
Prices incl. VAT;
The new Oberland Arms Alu SEPP - two-handed knife The aluminium SEPP, created by renowned Italian designer Tommaso Rumici, has long since become a modern classic.The latest generation is now being produced by premium manufacturer Lionsteel in Maniago, Italy - with high-precision technology and the expertise of experienced craftsmen. The special feature: an integral handle milled from solid aluminium that meets the highest standards of design, ergonomics and workmanship.This puts the new Alu SEPP in the absolute top class - uncompromising in terms of quality, function and aesthetics.The scope of delivery includes a MOLLE-compatible knife pouch made of robust nylon, colour-matched to the knife and manufactured using a precise laser-cut process. Manufactured in Germany, the pouch is also ideal as a magazine pouch or for other tactical equipment.Technical details: Blade length: 95mm/3.5mm Steel: M390 stonewashed / black PVD Handle material: Aluminium 7075 black or green hard anodised 7075 Weight: 133g Concept/Initial design: Matthias Hainich Design: Tommaso Rumici Production: Lionsteel, Maniago Italy Accessories: incl. Molle compatible knife pouch made of nylon, manufactured by Tactical Baer in Germany All Titan Sepp knives come with QR code with the BKA notification discreetly engraved on the handle (at no extra charge) All knives are provided with a consecutive serial number The knives are not subject to the weapons prohibition under §42a Weapons Act, because they are not one-handed knives. You can find the corresponding notice of determination from the BKA above under documents! At explicitly designated weapons prohibition zones, the knives, just like any other knife, may not be carried.
Prices incl. VAT;
The striking design looks light and elegant on heavy vehicles. 20-inch chrome alloy wheel for New Defender Data: Wheel size: 9x20" ET: 37 Bolt pattern: 5x120 Colour: chrome, black Special features: suitable for winter use
Prices incl. VAT;
Seat covers for Suzuki Jimny I Small as ever, but even more oho! That's the Jimny. Not an SUV for transporting the kiddies to riding school, but a real off-roader with a Twingo-like footprint of just 3.65 x 1.65 metres. Since the Jimny is a traditional workhorse with limited interior space, every cubic centimetre of free space counts. Off-the-shelf seat covers can't do this, they slip, overhang, get stuck or snag on moving parts. That's why our high-quality covers are tailor-made and fit extremely precisely thanks to individual Velcro straps. This also applies to the perfectly fitting headrest protector. As one of the last true off-road vehicles, the Jimny is particularly popular with foresters, fishermen, farmers and other 4x4 enthusiasts. Dirt, dust and animal residues therefore stay better on the easy-to-clean 100% nylon slipcovers than in the seats themselves. But of course our covers can do even more: in addition to a generous zipped pocket, high-quality Molle on the back of the front seat covers ensures clever expandability of the storage space. For example, our practical bag set can be attached here, the first aid scissors can be stowed within easy reach or the tensioning and fastening strap set can be used to secure everything that otherwise likes to fly around. Of course, the covers are also airbag-compatible. Available for: Suzuki Jimny I Set consists of: Driver's side, passenger's side Colour: Coyote, Black, Material: 100% Nylonwashable 30-60° C Made in EU! Please select the desired variant and colour. You will find illustrated instructions (for Jimny GJ/HJ) under documents. This article was designed in our in-house tailor shop. A dedicated team and short distances allow for continuous quality control and further development of our textile products. And if you already have a tailor's workshop in house, then it is easy to also accept customer change requests, special designs, suggestions and proposals for improvement at short notice and to implement them as far as possible. Mail or phone call is all it takes! And by the way: For this product, we use nylon fabric with a polyurethane (PU) coating. Both the fabric and its coating are PVC-free. Flexible PVC materials may contain phthalate-based plasticisers, some of which are legally restricted due to their potential health risks. That's why we deliberately avoid PVC in this product and opt for a high-quality PU coating instead – a more expensive alternative for us, but one we've consciously chosen.
Prices incl. VAT;
Service Kit for Land Rover New Defender L663 – Maintenance in original equipment quality Complete filter set for routine maintenance of the Land Rover Defender L663 – available for various engine versions. This service kit includes the essential filters and an oil drain plug for routine servicing of the Land Rover Defender L663 from model year 2020 onwards. All components are of OE matching quality and are matched to the respective engine version. Regular maintenance and timely filter replacement help maintain the engine's performance and long-term reliability. This kit provides the required components for a filter change in one package, eliminating the need to order each part separately. The service kit is suitable for use in professional workshops as well as for maintenance carried out by experienced vehicle owners. Scope of Delivery 1 × Oil filter 1 × Engine air filter 1 × Cabin air filter / Pollen filter 1 × Oil drain plug Vehicle Compatibility Vehicle: Land Rover Defender L663 (New Defender) Model year: From 2020 onwards Engine: Available for various engine versions – please select the appropriate option from the drop-down menu. Quality: Replacement parts in OE matching quality Important Notes Engine oil is not included and must be purchased separately. Before ordering, please check your vehicle's engine version and select the corresponding kit. Always follow the vehicle manufacturer's specified maintenance intervals and engine oil specifications.
Prices incl. VAT;
Bargains, information & practical items and gift ideas - discover the diversity of our off-road shop
Whether you're looking for special offers, clever accessories for everyday off-road use or inspiring gift ideas for adventure fans - you'll find what you're looking for in this category! We have put together everything that off-road fans will love: from reduced top products and practical gadgets to unusual gifts.
Bargains - quality at the best price
Our bargain section offers you high-quality products at unbeatable prices. Here you will find:
- Discounted off-road equipment: save on popular items such as roof tents, lighting systems and camping accessories.
- Remaining stock and discontinued models: grab them quickly before the best offers are sold out.
- Exclusive special offer packages: Ideal for equipping yourself fully for your next tour.
- Don't miss the opportunity to secure first-class off-road products at attractive prices!
Information & practical tips - for perfect preparation and organization.
Off-road adventures require well-thought-out planning. Our practical helpers will support you:
- Travel guides and maps: Detailed information for off-road routes and campsites.
- Tools and emergency equipment: Everything you need off-road for repairs or safety.
- Organizational aids: Clever solutions such as packing systems, bags and storage solutions.
These items make your everyday life easier and ensure that you are prepared for all eventualities.
Gift ideas - joy for off-road enthusiasts
Are you looking for an original gift for friends, family or colleagues who love adventure? Whether for birthdays, Christmas or simply as a little surprise - our gift ideas are guaranteed to generate enthusiasm.
Why this category is special
Here you will not only find high-quality products, but also inspiration and practical tips to make your off-road adventure even better. You can also save money with our bargains or make others happy with thoughtful gift ideas.
By the way
The combination of reduced offers, useful accessories and creative gift ideas makes this category a real highlight of our off-road shop. Browse through our range and discover how diverse the world of off-road adventures can be.
Check back regularly - there are always new bargains, practical tools and gift ideas to discover!