Installation service for warm air ducts for ventilation plates for all models The installation of the warm air duct is carried out at the specified fixed price, regardless of the duration.   Please note: The price refers only to the installation flat rate, including the required plastic conduit. The ventilation plates must be purchased separately.   Depending on whether you want to conduct heat from an external mobile heating box into the interior of the vehicle or from the interior of the vehicle via a permanently installed auxiliary heating system into, for example, a roof tent, you can purchase the following items from us:   Ventilation plates for a wide range of vehicles can be found here. Waluflex warm air pipe End piece for Waluflex warm air hose Permanently installed auxiliary heaters can be found here. Mobile auxiliary heater boxes can be found here.   Please note that built-in wind deflectors may need to be removed when installing a warm air duct through a ventilation grille.   When ordering, please provide your telephone number so that we can arrange an appointment. Installation is only possible on site in Berg near Neumarkt (postcode: 92348).   If you order the flat rate together with the appropriate ventilation plate, the item can also be shipped. If you already have ventilation plates, we can perform the installation service by appointment.  

Webasto pipe connector / double socket, with 60 mm connection Warm air pipe connector for effective distribution of warm air. The warm air pipe connector can be used to connect two warm air pipes with each other. Diameter: Ø 60 mmPrice per piece

Exhaust silencer for AUTOTERM (=Planar), Binar, Eberspächer parking heaters This stainless steel exhaust silencer is suitable for all parking heaters (air heating and water heating) with a 24 mm exhaust pipe.Suitable for the following heaters:    AUTOTERM Air 2D and AUTOTERM Air 4D (formerly Planar 2D, Planar 44D), AUTOTERM Flow 5D (formerly Binar 5D).    Eberspächer AirtronicAs the Webasto heaters have a 22 mm exhaust pipe, this silencer does not fit.Dimensions:    Outer diameter connection: 24 mm    Total length: 18 cm    Length of silencer without connections: 14 cm    Diameter: 40 mm (additional 2 cm fastening device)

Parking heater set for the VW T5 consists of all important components required for the installation of a parking heater. First and foremost, the set contains the AUTOTERM (=Planar) 2D12 parking heater, which is celebrated as an affordable and powerful alternative to Webasto and Eberspächer parking heaters. In addition to the heater holder with installation box, which can already be ordered individually and which was specially designed for the installation of the Planar parking heater in the VW T5, with this set we put together a comprehensive package for you with a matching hose clamp, fuel line, air duct, a warm air outlet and much more. As some components for the B-pillar vary depending on the vehicle model, please select the matching set for your VW T5 estate / panel van OR Multivan / Shuttle / California. Please note: This set is not suitable for vehicles with a partition wall! Scope of delivery: AUTOTERM 2D parking heater 12 volt incl. silencer, intake air hose, heat protection hose, tank intake pipe and exhaust corrugated pipeOptionally analogue control unit simple control (PU-5) with rotary control or digital control unit Comfort Control with timer switch5 metre connection cable for control panelSpecial heater bracket for VW T5, optionally with additional installation boxAir outlet for heating air 60 mm1 metre warm air pipe (diameter: 60 mm)60 mm to 90 mm adapterWarm air outlet for rear B-pillarAir duct for B-pillar incl. frameWarm air outlet for B-pillar frontAir ductFixing material (screws, nuts, hose clamp, cable ties)Technical data of the parking heater: Fuel type: dieselHeating capacity: max. 1.8 kW, min. 0.8 kWVolume of heated air: max. 75 m³/h, min. 34 m³/hFuel consumption in operation: max. 0.24 l/h, min. 0.1 l/hPower consumption in operation: max. 29 W, min. 10 WWeight: 3 kg (independent heater)Manual start/stop The AUTOTERM (=Planar) 2D12 is equipped with a height kit. This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heat output decreases proportionally to the amount of oxygen in the air. Roughly speaking, from 2,000 metres the loss of output per 500 m altitude is approx. 5%. Manufacturer tests up to 3,440 m were trouble-free. Up to 4,000 m no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not yet be tested at real altitude. Important:Especially when used at high altitude, the free travel of the fan is extremely important!Route the combustion air intake and exhaust extremely short and with low resistance - i.e. no kinks, no blockage or reduction. It should also be noted that operation beyond 3,000 m is still a technical compromise. Again, care should be taken to ensure that the combustion chamber is properly heated on a regular basis. The chamber must be burnt free of soot deposits. Soot deposits can also form on heaters that are permanently run at the lowest setting. Therefore, the following still applies: No guarantee for sooty combustion chambers! In order to ensure the longevity of the heater, you should also free-burn it occasionally at low levels. The combustion chamber reaches full temperature after running at full load for about half an hour. Normally, no further maintenance is required. In case of extreme loads, e.g. during longer overnight stays at more than 4,000 m, the combustion chamber including the seal set should be cleaned if necessary. To heat your roof tent using your auxiliary heating system, we offer an installation service for a warm air duct through a ventilation plate. We will be happy to advise you: ☎ +49 9181 466 644 https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Warm Air Where You Need It: The Highly Flexible 60mm Warm Air Ducting! Are you currently installing your parking heater or optimizing your existing system? Rigid, unwieldy hoses make your life difficult when it comes to directing warm air exactly where it's needed – whether in your camper, off-road vehicle, rooftop tent, or boat. With our highly flexible warm air ducting (inner diameter 60mm), installation becomes child's play! Its enormous flexibility allows you to master even complicated routing and tight radii without any problems. This makes our warm air ducting the first choice: Maximum Flexibility: Can be laid in the tightest installation spaces and around sharp corners without kinking or blocking airflow. This saves time and nerves during installation. Optimal Airflow: Despite its flexibility, the hose ensures good flow for efficient distribution of warm air from your parking heater. Robust Quality: Developed for the demands of a vehicle environment and resistant to the typical temperatures of a parking heater. Universally Suitable: With an inner diameter of 60mm, it is compatible with the connections of many common parking heater models – ideal for the AUTOTERM 2D parking heater, but also for Webasto, Eberspächer, and Truma heaters. As this hot air ducting is particularly flexible, we recommend it for use with our mobile air heater. Sold by the Meter for Your Needs: You order exactly the length you need for your project. This way, you avoid unnecessary waste and save costs. The hose is delivered as one continuous piece in the ordered length. Whether you want to direct the warmth specifically to the footwell, sleeping areas, or a particular area of your vehicle – this hose makes it easy. Notes: Inner diameter: Ø 60 mm Price per linear meter, sold only in whole meters. The pipe is completely waterproof. Example: If you need 3 meters of hot air ducting, add this item to your shopping cart 3 times. Please note: A maximum of 10 meters can be delivered in one piece. If you order, for example, 20 meters, you will receive 2x10 meters. Individual pipe sections can be connected without problems using the pipe connector. You can find a suitable storage bag for the hose here. Put an end to rigid solutions! Order your highly flexible warm air ducting now and enjoy cozy warmth exactly where you want it!

Durable 90° Stainless Steel Heater Bracket for Parking Heaters This high-quality stainless steel heater holder with 90 ° angle fits the following auxiliary heaters: Planar 2D parking heater Planar 4D parking heater Planar 44D auxiliary heating only with the same flange pattern: Webasto & Eberspächer

Waluflex Special Sale Stock Clearance If you’re looking for hot air flex ducts, you’re in for a treat in our special Waluflex clearance sale. We’re selling leftover lengths and cut-offs of trusted Waluflex pipes for great discount prices: Lengths between 60-100cm will cost only 9,89€ (incl. VAT) per piece, longer sections between 110-170cm will be 18,15€ (incl. VAT) each or longer sections between 170-230cm will be 28,00€ (incl. VAT) each. Please note that these pieces of piping are sold straight from our warehouse as they are, that’s why we can’t take orders for specific lengths, unfortunately. The piping is specially tailored to suit the AUTOTERM (=Planar) 2D auxiliary vehicle heater, but also fits Webasto, Eberspächer and Truma heaters. The pipe is completely waterproofDiameter: Ø 60 mm Only as long as supply lasts.  

Wear kit with tank extraction and exhaust pipe for AUTOTERM Air 2D / 4D  For our portable heater boxes, we only use AUTOTERM (previously Planar) Diesel heaters. After assembly, we are usually left with unused accessories and spare parts from the original AUTOTERM delivery, so we decided to bundle them as wear and tear replacement kits for only 20 € incl. VAT. That’s a massive price reduction of nearly 70% when compared to the individual value of these spare parts.The sets will fit AUTOTERM 2D and 4D air heaters and consist of one fuel pick-up tube, one fuel line, one exhaust pipe including heat insultation and various pieces of fastening materials. These are essential spare parts and replacements to keep handy in case of damage or wear and tear.

Autoterm Air 2D repair kit The set consists of the following components: Glow plug screen Gasket for the glow plug Gasket for the combustion chamber Seal for the fan motor Seal for the fuel line Caution: Opening the appliance yourself within the warranty period will invalidate the warranty. Repairs should therefore be carried out by specialised companies.

Simple control panel (PU-5) for Planar parking heaters The control panel offers easy operation of the Planar parking heaters. The heater can be switched on or off manually via the control elements. Furthermore, the heat output can be regulated via the control panel.Control elements: Planar-5M  1. switch ventilation off/on2. switch heating on/off3. LED light to indicate the status of the heater    - yellow light = heater running    - slow, red flashing = malfunction4. LED light for status display of ventilation    - Green light = ventilation running    - green flashing = ventilation off    - yellow light = heating and ventilation are on together5. rotary control

Module for 12 Volt AUTOTERM parking heaters With this module and a suitable radio remote control, you can control AUTOTERM (Planar 2D12 and Planar 44D12) parking heaters. You need the module to assign the parking heater to a channel of a radio remote control. You can thus switch the parking heater on and off by remote control. A connection diagram is included in the scope of delivery.

Nakatanenga parking heater console 2 New version of the proven parking heater console, it allows the installation of a parking heater (e.g. Webasto Airtop 2000 STC, Eberspächer Aitronic D2 or D11C or AUTOTERM (=Planar 2D12)) under the cubby box of the Land Rover Defender 90/110/130, turning it into an armrest at a comfortable height (158 mm higher). The display of the parking heater is recessed into the front panel of the console.Please note: New holes have to be drilled for the installation of the parking heater console; the required fixing material is included in the scope of delivery.The ever-growing need for power sources in the vehicle cockpit - whether in the classic cigarette lighter format (12 V) or as a 5 V USB socket for Apple iPhones, navigation devices, iPads, smartphones or similar. - the new generation of the Nakatanenga parking heater console now also meets these requirements in the best possible way: it is optionally available with heavy-duty 12 V sockets and/or USB charging sockets from the marine sector. These are then already included in the scope of delivery, so they do not have to be ordered separately. A Webasto air vent can be attached to the cut-out at the rear. In the cut-out for the Planar parking heater, the display is glued on and the cable is fed through the square hole. If none of the front panels contains your desired cut-outs, you can order the front panel without cut-outs and process it accordingly.Basic dimensions: 47.5 cm x 26.5 cm x 15.5 cmATTENTION: An AUTOTERM Air 4D (=Planar 44d) is not recommended for this purpose!

Complete set of AUTOTERM Air 2D parking heater for Defender The parking heater set AUTOTERM (Planar) 2D12 for the Land Rover Defender consists of all important components needed for the installation of a parking heater. Included in the delivery are the AUTOTERM 2D 12 Volt parking heater, our Nakatanenga parking heater console, the Nakatanenga mounting plate, a fuel tank extraction, a Webasto air outlet with 60 mm connection, 30 cm warm air pipe and a vibration damper.As a low-priced and powerful alternative to our Webasto parking heater kits, the AUTOTERM (=Planar) 2D parking heater is proving to be a real sales hit. This is partly due to the particularly compact dimensions, which allow installation even in small cars, vans, off-roader motorhomes, construction machinery, boats or in difficult installation situations. In the off-road / 4x4 sector, it is ideally suited for the "typical" off-road vehicles such as Land Rover Defender, Mercedes G or Jeep Wrangler JK.These are only a few of many reasons why we now offer the AUTOTERM (Planar) 2D 12 V parking heater in a clear and comprehensive complete set for the Land Rover Defender at an economical price. For both the Tdi/ Td5 and the Td4, we offer one set each with a perfectly matching accessory kit.You can select different front panel cut-outs for the parking heater console included in the scope of delivery. The associated connections are available in the classic cigarette lighter format (12 V) or as 5 V USB charging sockets for Apple iPhones, navigation devices, iPads and smartphones and are included in the scope of delivery.The parking heater can also be operated while driving.Running time: The AUTOTERM parking heater switches off automatically after 2 hours of operation. However, as soon as you press a button during operation, the parking heater continues to run indefinitely until it is switched off manually.Scope of delivery:- AUTOTERM 2D parking heater 12 volt incl. silencer, intake air hose, heat protection hose, tank intake pipe and corrugated exhaust pipe.- Optionally analogue control unit simple control (PU-5) with rotary control or digital control unit comfort control (PU-29) with time switch- Nakatanenga parking heater console incl. the selected connections- Nakatanenga mounting plate- Fuel filler cap- Webasto air outlet with 60 mm connection, rotatable- 30 cm warm air pipe (diameter: 60 mm)- Vibration damper- Fixing material (screws, nuts, clamps, shrink hose, cable ties)Technical data:- Fuel type: diesel- Heating capacity: max. 1.8 kW, min. 0.8 kW- Volume of heated air: max. 75 m³/h, min. 34 m³/h- Fuel consumption in operation: max. 0.24 l/h, min. 0.1 l/h- Power consumption in operation: max. 29 W, min. 10 W- Weight: 3 kg (independent heater)- Manual start/stop → On the Autoterm.cz site you will find a calculator for the correct dimensioning of the air heater,You can choose between two control elements:- Simple Control (PU-5) element with rotary control: The old PU-10 control element had a relatively inaccessible control surface. Therefore, the reliable control element with rotary control is now the new improved standard of the Planar parking heaters! With the rotary control, you can adjust the heating power of the parking heater and regulate the power of the ventilation in ventilation mode! The PU-5 control element with rotary control can also be purchased separately here.- The digital control element comfort control (PU-29) with timer has an OLED display and an understandable and clear interface.  Temperature, ventilation and power can be configured via the display and the various buttons. With the timer, you can easily set the start of the parking heater to a specific time. The digital control element with timer can also be purchased separately here.Setting options comfort control (PU-29):- Temperature and power (adjustable for the parking heater, the control panel and for an external heater).- Time and date - Operating language (English or Russian)Functions of the timer comfort control (PU-29):- Memory function: save the time so that the parking heater starts at this time every day - Configurable memory locations: Up to 3 different weekdays with different times can be set and saved. The AUTOTERM (=Planar) 2D12 is equipped with an altitude kit.This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heat output decreases proportionally to the amount of oxygen in the air. Roughly speaking, from 2,000 metres the loss of output per 500 m altitude is approx. 5%. Manufacturer tests up to 3,440 m were trouble-free. Up to 4,000 m no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not yet be tested at real altitude. Important:Especially when used at high altitude, the free travel of the fan is extremely important!Route the combustion air intake and exhaust extremely short and with low resistance - i.e. no kinks, no blockage or reduction. It should also be noted that operation beyond 3,000 m is still a technical compromise. Again, care should be taken to ensure that the combustion chamber is properly heated on a regular basis. The chamber must be burnt free of soot deposits. Soot deposits can also form on heaters that are permanently operated at the lowest setting. Therefore, the following still applies: No guarantee for sooty combustion chambers!In order to ensure the longevity of the heater, you should also free-burn it occasionally at low levels. The combustion chamber reaches full temperature after running at full load for about half an hour. Normally, no further maintenance is required. In case of extreme loads, e.g. during longer overnight stays at more than 4,000 m, the combustion chamber including the seal set should be cleaned if necessary. To heat your roof tent using your auxiliary heating system, we offer an installation service for a warm air duct through a ventilation plate. https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Installation box for AUTOTERM (=Planar) 2D parking heaters Our installation housing for the AUTOTERM (=Planar ) 2D parking heater can be mounted on the outside of loading areas or vans. Thanks to the sturdy material, you no longer need to worry about the parking heater being damaged by the load, for example. With this installation box, you save space in the vehicle and in the engine compartment and protect the parking heater at the same time!  The installation box is also suitable for Webasto Air Top 2000 and Eberspächer D2 parking heaters. Dimensions: 35x15x13 cm Scope of delivery: 2-piece installation box 4 screws, 4 washers Pre-assembled cable grommet  

Additional tank 7.5 litres for parking heaters This additional tank can be placed anywhere on the vehicle.The tank can be filled with 7.5 litres of fuel, e.g. for the AUTOTERM Planar 2D parking heater. Suitable fastening material is included in the scope of delivery.

Dropside bushing 25.4mm for the intake of the AUTOTERM (=Planar) parking heater Side panel bushing for all AUTOTERM parking heaters with an intake pipe diameter of 25.4mm (AUTOTERM Air 4D & AUTOTERM Air 2D).Please note:When installing the parking heater, you must observe the general wading depth of the vehicle. Depending on the placement of the parking heater intake, the wading depth may change individually for the vehicle. Please also be sure to observe the instructions of the parking heater manufacturer!

Tank-mounted fuel intake pipe The 60 cm tank-mounted fuel intake pipe is perfect for our diesel heaters by Autoterm, but will also suit most other products like Webasto or Eberspächer. It will work with both diesel and gasoline on either air or water heated systems and it doesn’t matter whether your tank is plastic or metal. To fit the intake pipe, it is generally necessary to remove the fuel tank and its fittings. After drilling a hole for the intake pipe, the connector head has to be countered with a nut from the inside. That’s why access to the tank’s interior through the intake opening is a must. The flexible riser pipe can be bent into any shape, making it easy to determine the extraction level for the heater. Make sure that the opening of the pipe doesn’t reach all the way to the bottom of the tank, otherwise you’ll risk complete emptying of your fuel tank and the unwanted intake of dirt particles or tank sludge. The tank extraction is ideally suited for our Planar parking heaters.