Vehicle accessories

This full stainless steel spare wheel carrier for Defender SW/HT is the successor to our Defender spare wheel carrier RRHNAHI sold by the hundreds. It is available in two colours. The Defender rear door suffers from the heavy weight of the large spare wheel. Depending on use, after about five years or 50.000 kms the first cracks in the rear door frame appear. There are two solutions for this well-known problem: either move the spare wheel to the bonnet (see our bonnet spare wheel mount for that, not possible for post MY 2007 Defenders) or you fit our rear door spare wheel carrier. It takes off the complete weight from the rear door and opens along with the door. The carrier is fitted to the rear crossmember, a plate is mounted to the existing holes in the door, which is then attached to the carrier with two cranked stainless steel pivots. This carrier has been tested extensively, among others on the "Grand Erg" rallye and combines easy fitting with high toughness and exeptional usability. Available for all Defender models with rear door (Station and Hardtop). Improved design in 2014 and full stainless steel fabrication. The bearing is maintenance free, the complete carrier rustproof and can be completely revised it necessary. It's compatible with Land Rover rear step / bumper with towbar. Fitting is possible on a DIY basis. We also offer fitting service. If you also 'buy' the fitting charge we will contact you for an appointment. The spare wheel carrier opens together with the rear door, no further unlocking necessary. For vehicles with a tailgate (Pickup, not HCPU) we offer a separate sparewheel carrier: NARRTDEF-STPU The carrier is fully made out of stainless steel and black powder coated. The spare wheel carrier is designed and tested for a total weight (spare wheel and possibly other accessories) of 120 kg.

Running board round tube for Land Rover Defender, stainless steel The round tube running boards serve as an entry aid and vehicle protection. They are made of stainless steel and have an aluminium tread surface with rubber pads to minimise the risk of slipping.The running boards are available for various wheelbases, delivered in pairs, optionally in stainless steel look or with additional black powder coating. Please select below.Delivery is in pairs.The running boards are at the original height (i.e. at the same height as the original Land Rover running boards) and therefore under the bodywork.You can find a suitable crossbar here.

SUPERWINCH SX 10SR black The 12 V Superwinch electric winch SX 10 SR has a three-stage planetary gear.The winch is equipped with an automatic load holding brake with mechanical cone brake for large loads and a freewheel clutch for pulling off the rope by hand. The Superwinch electric winch SX 10 SR has waterproof sealed relays for high electrical currents, which allow a longer duty cycle. The rope drum has a patented lighting system.It is used for commercial recovery of rolling loads.Features:Rope speed: 8.3 - 1.4 [m/min].Pulling force: 4.5 tVoltage: 12 VWeight: 61 kgPower consumption at full load: 363 AMovable control boxScope of delivery:     1 x cable winch black     1 x synthetic fibre rope 9.5 mm/ 24 m       1 x cable mouth     1 x relay box     1 x battery cable     1 x cable remote control     1 x radio remote control  

SUPERWINCH SX 10SR The 12 V Superwinch electric winch SX 10 SR has a three-stage planetary gear. The winch is equipped with an automatic load holding brake with mechanical cone brake for large loads and a freewheel clutch for pulling off the rope by hand. The Superwinch electric winch SX 10 SR has waterproof sealed relays for high electrical currents, which allow a longer duty cycle. The rope drum has a patented lighting system. It is used for commercial recovery of rolling loads.Features:Rope speed: 8.3 - 1.4 [m/min].Pulling force: 4.5 tVoltage: 12 VWeight: 61 kgPower consumption at full load: 363 AMovable control boxScope of delivery:     1 x cable winch     1 x synthetic fibre rope 9.5 mm/ 24 m       1 x cable mouth     1 x relay box     1 x battery cable     1 x cable remote control     1 x radio remote control  

The XPL Curved Lightbar is an extremely powerful installation solution for the slot of the standard radiator grille Installing work lamps, additional headlights or light bars on your vehicle is not too difficult – when you’re talking older pickups or classic Defenders, that is. Obviously, with newer cars like the New Defender one should be a lot more cautious before drilling holes or attaching brackets to the expensive exterior. Vision X Lighting specialize in custom solutions, combining top performance, sleek design and installation methods that minimize effort and actual alterations to your car.  The XPL Curved Lightbar by Vision X is an elegant and powerful LED solution for the lower opening in the standard grille of the New Defender. The array of individual 5 W CREE LEDs delivers a light beam of over 600 m – providing safety in all weather conditions, off-road or on-road, for work or sports. The XPL Curved lightbar also features backlighting that can be used as daytime running lights.  The installation is fairly simple and requires roughly 4 hrs. Both the grille’s plastic substructure and the lower opening need to be modified by sawing out specific areas. Detailed instructions, fastening materials and electric connections are included in the delivery. Mounting behind the radiator grille is also possible.  Specifications for XPL Curved Lightbar: LEDs: 5W per LED Housing material: aluminium Light colour temperature: 6000 Kelvin Voltage: 9-32V DC Current: 3.12A~8.96A@24V DC - 6.25A~17.92A@12V DC Vibration resistance: 21 Grms Lens material: Polycarbonate Smooth backlight Proprietary IRIS reflector technology Curved high power light bars Weatherproof Deutsch connector with plug-and-play wiring harness Certifications: CE, RoHS, IEC 62471, ECE R112 Thanks to our iris reflector technology and the unique curve of the bar, the XPL Curved series produces a wide spot beam pattern with a range of over 600 metres. Scope of delivery: Complete radiator grille set for New Defender with XPL-HC23 light bar, brackets and wiring harness including detailed installation instructions.

The Horntools Alpha 12.0 Super Speed ​​Edition With its low weight and compact dimensions, it is perfectly suitable for vehicles with a total weight of up to 4 tons.   Furnishing: 9.2 mm Ø galvanized steel cable with 28 m length with hook INFO: Steel rope is included separately in the scope of delivery stainless steel roller rope window remote control 1x cable 1x radio integrated (delivered without battery) potted reinforced relay (contactor) waterproof motor IP67 sealed by groove with sealing ring removable control unit (so that the control can be installed as desired) freewheel lever * gear neutral position made of stainless steel cross braces made of stainless steel reinforced rope drum ** (suitable for use with plastic rope) powder-coated aluminum die-cast housing, motor / gearbox reinforced contactor housing made of deep-drawn sheet metal, powder-coated internal drum brake with 3 brake shoes cable length: 1.7 m cable cross section: 50 mm² 3 year guarantee operation manual * A freewheel lever is used to decouple the gearbox to quickly unwind the winch by hand. Technical specifications: working range voltage: 10-16 Volt max. Power consumption 600 A ** train speed free of load 11 m / minute traction 5,400 kg ** 3-stage planetary gear 110: 1 geared down net weight: 25.8 kg without rope and rope window Series wound motor * drum (ØxLength): 63x226 mm overall size (LxWxH): 577 x 160 x 225 mm * Series motor with an electrically generated magnetic field ** Values ​​can vary considerably, depending on the battery system, the winch can pull up to twice, the traction is designed for a standard 70 AH battery. With more powerful battery systems, the pulling power must be limited by the current / voltage. 

Ideal carrier system for off-road use and for tradesmen Off-road use with the Ford Ranger requires particularly stable mounts, as the vehicle is exposed to higher forces. We have built the platform for the Ford Ranger / Raptor with this in mind. You have sufficient space and fastening options for attaching load securing devices or bolting on practical roof rack accessories. Heavy loads on the roof of the Ford Ranger can therefore be positioned anywhere on the roof rack platform and securely lashed down. Both across the roof and in the direction of travel. Roof rack uses the original attachment points, no drilling required Compatible with Ford Ranger (XL, XLT and Tremor from 2023), Ford Ranger Raptor (from 2023) and VW Amarok (Entry, Style and Life from 2023) Aerodynamic deflector is included in the scope of delivery ExRoof roof rack for Ford Ranger & Raptor (from model year 2023) The innovative horntools ExRoof roof rack is your perfect everyday companion! Thanks to its all-round profile rail, any add-on parts can be attached using sliding blocks. The ExRoof roof rack for the Ford Ranger / Raptor is made of powder-coated aluminum and therefore weighs just 33 kg. With a size of 1400 x 1280 mm, you have enough space on the ExRoof platform to mount a roof tent, transport boxes, tools and other accessories on the roof of your vehicle.   This Ford Ranger roof rack is also very popular with tradesmen. If the loading area of the pick-up is no longer sufficient for tools or other transport items, toolboxes or ladders can be safely stowed on the platform.   Technical data: Dimensions: 1400 x 1280 mm (platform) Weight: 33 kg (roof rack + roof rack platform) Surface: RAL 9005 powder-coated Scope of delivery: Roof rack feet Roof rack platform Wind deflector Fastening material and installation instructions

ExRoof roof rack for Isuzu D-Max 2021 Double Cab (from year of construction 2021)   The horntools ExRoof roof rack is your perfect everyday companion! Thanks to its all-round profile rail, add-on parts can be attached using sliding blocks. The ExRoof is made of powder-coated aluminum and therefore weighs only 20kg. With a size of 1600mm x 1250mm x 49 mm, you have enough space to store your accessories.   Technical data: Material: Aluminum 6063 Weight: 20 kg Surface: Powder coating Size: 1600mm x 1250mm x 49 mm Scope of delivery Base carrier Roof rack feet Fastening material and installation instructions Caution: Static load capacity: 300 kg Dynamic load capacity: 100 kg The dynamic load capacity is not the manufacturer's approval. The manufacturer's load capacity must not be exceeded. The static load indicates the load capacity when stationary. The dynamic load capacity refers exclusively to paved roads. The load must be evenly distributed over the entire surface.  

Off-road protection in aluminium: LAPIS rock sliders for Ford Ranger from 2023 onwards Robust aluminum construction:Lightweight yet extremely resistant to impacts and external influences Effective cab protection:Protects the underside of the vehicle from damage caused by stones, branches or other off-road obstacles Simple installation:Fitting to the original attachment points enable uncomplicated installation without complex adjustments such as drilling holes Easier access:Provides additional step surface for driver and passenger Weatherproof:High-quality powder coating for long-term protection against corrosion and environmental influences TÜV parts certificate included in the scope of delivery The popular running boards for the new Ford Ranger from model year 2023 are here: Robust Rockslider design made of aluminum, the front panel is reinforced with “dimple die” beading. The steps can be unscrewed or replaced if necessary. They are fitted to the vehicle using the existing threaded inserts on the underside of the bodywork.   The decision was made to use a lightweight construction, which is why the Rockslider is a functional cabin guard made of aluminum. It is not suitable for a jack, but provides more than adequate protection in moderately difficult terrain.   The running boards are compatible with the following models from model year 2023: Ford Ranger XL Ford Ranger XLT Ford Ranger Wildtrak Ford Ranger Wildtrak X Technical details: Weight: 35 kg (per pair) Material: Aluminum Color: Black (powder-coated) Scope of delivery: 2 x Rockslider (driver's side & passenger's side) mounting material installation instructions TÜV parts certificate

CONTINOUS DUTY, 485C CE-Compressor, 12V Specifications:   12-volt Permanent magnet motor Duty cycle: 100 % at 200 PSI (13.7 bar) Max. Working pressure: 200 PSI Max. Air tank size: 5.0 gallons (approx. 19 litres) Max. Power consumption: 23 Amps Protection class: IP67 Dimensions: 270 mm L x 105 mm W x 165 mm H Net weight: 4.99kg. As a pioneer and market leader in the field of automotive compressors, VIAIR has set the highest quality standards that apply to all VIAIR compressor models and series. Here is a small excerpt of the most important features:Stainless steel valves guarantee long-lasting and optimised shut-off timesgenerously dimensioned cooling fins on design-optimised cylinders ensure maximum air dissipation and a longer service lifeAnodised cylinder running surfaces increase protection against abrasionthe piston motor with PTFE piston rings ensures the lowest friction and therefore optimum smooth running and service life propertiesthe motors are protected against splash water and are therefore highly resistant to corrosionintegrated, automatic overheating protection protects the longevity of the compressorsCE labellingTechnical data:    2.5 gallons (approx. 9.5 litres) VIAIR air tank (200 PSI / 13.7 bar) 485C Stealth Black VIAIR compressor with thermal overload protection Digital tyre inflation gun with 180 PSI (12.4 bar) Braided black spiral hose with quick-release coupling 1/4’ NPT quick coupling bolt (F) 1/4’ NPT quick coupling (F) Dashboard indicator with ON / OFF switch Sealed pressure switch (165 PSI (11.3 bar) on, 200 PSI off (13.7 bar) Reducer 1/8‘ NPT (F) to 1/4’ NPT (M) Reducer 3/8‘ NPT (F) to 1/4’ NPT (M) 1/4’ NPT 250 PSI safety valve 1/4’ NPT drain cock (3) 1/4’ NPT compression fittings Suitable for tyres up to 37 inches 4-inch protective sleeves (grommet strips) for air line hoses - Make sure the air line hoses are protected from the sharp edges of the borehole with the supplied grommet strip.Please note: Use thread sealant for proper installation. Thread tape is not recommended. When properly sealed, the recommended torque for 1/8’ is 13.5 Nm. The recommended torque for 1/4‘ and 3/8’ is 22 Nm.  

Robust Protection for Your Adventure: The 2-Piece Underbody Guard for the New Defender Do you enjoy taking your New Defender off the beaten path and want to provide optimal protection for your engine and transmission? Then this 2-piece underbody guard made of 6 mm thick aluminium from Terrafirma is exactly what you need! This massive protection is a significant improvement over the rather light-duty factory-installed skid plates. Thanks to strategically placed indentations and sturdy mounting points, it offers considerably higher strength and stability – precisely what you need off-road. This ensures your New Defender's engine and transmission (from model year 2020 onwards) are well-protected against stone impacts, grounding, and other hazards of off-road driving. The best part: The original soundproofing plates don't even need to be removed for installation, making the fitting process straightforward. Weighing in at 26 kg, this underbody guard is a true statement of robustness. Secure this essential companion for your off-road tours now and give your Defender the protection it deserves!

SUPERWINCH TIGER SHARK 11.5 The 12 V Superwinch electric winch Tiger Shark 11500 has a two-stage planetary gearbox. The winch is equipped with an automatic load holding brake with mechanical cone brake for large loads and a freewheel clutch for pulling the rope by hand. The Superwinch Tiger Shark 11.5 electric winch has waterproof sealed relays for high electrical currents, allowing longer duty cycles.It is used for commercial recovery of rolling loads.Features: Rope speed: 5.7 - 0.6 [m/min]. Pulling force: 5.2 t Voltage: 12 V Weight: 42 kg Power consumption at full load: 410 A Scope of delivery:     1 x winch     optional: 1 x steel cable 9.5 mm/ 25 m or plastic winch cable 10 mm/30 m - optional in orange or grey     1 x winch hook     1 x roller window     1 x relay box     1 x battery cable     1 x cable remote control

Running boards Land Rover Defender Why skimp on comfort and looks? These running boards for Land Rover Defender 110 not only look good, they also provide a safer and more comfortable entrance to your vehicle. The round tubes are black powder-coated and equipped with checker plates. The chequer plates on the entrance tubes have an anti-slip coating so that you can enter your vehicle safely.Fixing material is included in the delivery.Important note: These running boards are not compatible with the original splash flaps (front). You will find the matching mud flaps here as well as matching splash flaps here.They are delivered in pairs.Material thickness checker plate: 2.5 mm basic thickness / 4 mm incl. checker (quintet plate)You can find a suitable crossbar here.

Winch bumper TREKFINDER, Land Rover Defender, with/without air conditioning, incl. parts certificate This winch bumper is suitable for Defender models with or without air conditioning. The angle of the bumper is optimal for vehicles with air conditioning, because the bumper sits very far back. The bumper is made of quality steel, which is cathodic dip painted and then powder coated black. The material thickness of the tubes is 4mm and is welded watertight. Depending on the vehicle version and winch type, it may be necessary to adapt the radiator grille. Further info: 500 h salt spray test! 2 very stable plug-in mounts for the Hi-Lift jack A parts certificate is included in the scope of delivery. ATTENTION! The following articles are NOT included in the scope of delivery: Cable winch Winch cover Roller rope window cover

The Dixon Bate NATO Hitch: Your Robust Connection Professional with Road Approval! Are you looking for an extremely resilient and reliable trailer hitch for your 4x4 vehicle that can handle the toughest demands both off-road and on the street? Then the original Dixon Bate NATO Hitch is exactly the right choice for you! This powerhouse is not only proven for military purposes but, thanks to its E-certification mark, can also be used in civilian road traffic without requiring registration. Robustness and Functionality for the Highest Demands: This NATO hitch from Dixon Bate is designed for fixed mounting on your vehicle and offers you unsurpassed stability. Whether you're towing heavy trailers off-road or depend on an absolutely reliable connection for commercial use – you can count on this hitch. A special feature is its ability to rotate and lock. This provides you with maximum flexibility when coupling and uncoupling, even on uneven terrain, and ensures a secure connection while driving. The Advantages of the Dixon Bate NATO Hitch at a Glance: With E-Certification Mark: Thanks to the E-certification mark, this hitch is registration-free in many countries and legal for road use. This saves you tedious trips to the inspection office. Rotatable and Lockable: For maximum flexibility and safety during coupling and driving. For Fixed Mounting: Designed for permanent and stable attachment to numerous 4x4 vehicles. Extremely Resilient: Proven Dixon Bate quality for the highest demands. Universal Bolt Pattern: With a standard bolt pattern of 85 x 45 mm, it fits many common rear cross members and tow bars. Important Note on Installation: The hitch is delivered without mounting hardware. Please be sure to observe your vehicle manufacturer's specific guidelines for the correct and safe installation of the NATO hitch. When in doubt, consult a professional to ensure safety. With the Dixon Bate NATO Hitch, you equip your vehicle with one of the most stable and versatile trailer hitches on the market. Ideal for off-road enthusiasts, farmers, forestry operations, and anyone who doesn't want to compromise on towing capacity and safety. Get this proven classic for your vehicle now!  

For Land Rover Defender 90/110/130 with air conditioning, for Superwinch winches, without certification. Depending on the vehicle version and winch type, it may be necessary to adapt the radiator grille.

GDW hitch bracket with 13-pin Erich Jaeger E set The New Defender L663 (from MY 2019) is not only an extraordinary off-road vehicle, it also packs a remarkable punch. The wide variety of engines from Diesel and petrol to PHEV deliver between 200 and 525 HP and 400 to 650 Nm torque. Its power makes the new Landy the ultimate towing vehicle up to 3.5t towing capacity. And the fact, that the trailer hitch –  whether detachable or electrically deployable –  has to be ordered as an extra, is not really a disadvantage. When configuring your New Defender it’s probably best to skip this feature and get a heavy duty towbar like the one from GDW with its 13-pin electric connector kit by Erich Jaeger. The advantages of the GDW trailer hitch are obvious: A 4-bolt mounting plate will fit the included towball hitch but also any other type of coupling, the GDW coupling block comes at a much more competitive price than the OEM parts. Installation and road use do not need to be technically certified, by the way. The GDW towbar was custom-designed specifically for the New Defender. It comes with detailed assembly instructions and a complete electrics kit. Installing the towbar will take approximately 3 hours. Please note:The GDW towbar may interfere with the sensors of the vehicle’s parking aid. If you rely on this system, you should use the original tow bar. Maximum towing:   3,5 t Maximum vertical load:   210 kg (the maximum drawbar load is specified by the vehicle manufacturer and can be found in the vehicle documents)

Parking heater set for the VW T5 consists of all important components required for the installation of a parking heater. First and foremost, the set contains the AUTOTERM (=Planar) 2D12 parking heater, which is celebrated as an affordable and powerful alternative to Webasto and Eberspächer parking heaters. In addition to the heater holder with installation box, which can already be ordered individually and which was specially designed for the installation of the Planar parking heater in the VW T5, with this set we put together a comprehensive package for you with a matching hose clamp, fuel line, air duct, a warm air outlet and much more. As some components for the B-pillar vary depending on the vehicle model, please select the matching set for your VW T5 estate / panel van OR Multivan / Shuttle / California. Please note: This set is not suitable for vehicles with a partition wall! Scope of delivery: AUTOTERM 2D parking heater 12 volt incl. silencer, intake air hose, heat protection hose, tank intake pipe and exhaust corrugated pipeOptionally analogue control unit simple control (PU-5) with rotary control or digital control unit Comfort Control with timer switch5 metre connection cable for control panelSpecial heater bracket for VW T5, optionally with additional installation boxAir outlet for heating air 60 mm1 metre warm air pipe (diameter: 60 mm)60 mm to 90 mm adapterWarm air outlet for rear B-pillarAir duct for B-pillar incl. frameWarm air outlet for B-pillar frontAir ductFixing material (screws, nuts, hose clamp, cable ties)Technical data of the parking heater: Fuel type: dieselHeating capacity: max. 1.8 kW, min. 0.8 kWVolume of heated air: max. 75 m³/h, min. 34 m³/hFuel consumption in operation: max. 0.24 l/h, min. 0.1 l/hPower consumption in operation: max. 29 W, min. 10 WWeight: 3 kg (independent heater)Manual start/stop The AUTOTERM (=Planar) 2D12 is equipped with a height kit. This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heat output decreases proportionally to the amount of oxygen in the air. Roughly speaking, from 2,000 metres the loss of output per 500 m altitude is approx. 5%. Manufacturer tests up to 3,440 m were trouble-free. Up to 4,000 m no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not yet be tested at real altitude. Important:Especially when used at high altitude, the free travel of the fan is extremely important!Route the combustion air intake and exhaust extremely short and with low resistance - i.e. no kinks, no blockage or reduction. It should also be noted that operation beyond 3,000 m is still a technical compromise. Again, care should be taken to ensure that the combustion chamber is properly heated on a regular basis. The chamber must be burnt free of soot deposits. Soot deposits can also form on heaters that are permanently run at the lowest setting. Therefore, the following still applies: No guarantee for sooty combustion chambers! In order to ensure the longevity of the heater, you should also free-burn it occasionally at low levels. The combustion chamber reaches full temperature after running at full load for about half an hour. Normally, no further maintenance is required. In case of extreme loads, e.g. during longer overnight stays at more than 4,000 m, the combustion chamber including the seal set should be cleaned if necessary. To heat your roof tent using your auxiliary heating system, we offer an installation service for a warm air duct through a ventilation plate. We will be happy to advise you: ☎ +49 9181 466 644 https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Complete set of AUTOTERM Air 2D parking heater for Defender The parking heater set AUTOTERM (Planar) 2D12 for the Land Rover Defender consists of all important components needed for the installation of a parking heater. Included in the delivery are the AUTOTERM 2D 12 Volt parking heater, our Nakatanenga parking heater console, the Nakatanenga mounting plate, a fuel tank extraction, a Webasto air outlet with 60 mm connection, 30 cm warm air pipe and a vibration damper.As a low-priced and powerful alternative to our Webasto parking heater kits, the AUTOTERM (=Planar) 2D parking heater is proving to be a real sales hit. This is partly due to the particularly compact dimensions, which allow installation even in small cars, vans, off-roader motorhomes, construction machinery, boats or in difficult installation situations. In the off-road / 4x4 sector, it is ideally suited for the "typical" off-road vehicles such as Land Rover Defender, Mercedes G or Jeep Wrangler JK.These are only a few of many reasons why we now offer the AUTOTERM (Planar) 2D 12 V parking heater in a clear and comprehensive complete set for the Land Rover Defender at an economical price. For both the Tdi/ Td5 and the Td4, we offer one set each with a perfectly matching accessory kit.You can select different front panel cut-outs for the parking heater console included in the scope of delivery. The associated connections are available in the classic cigarette lighter format (12 V) or as 5 V USB charging sockets for Apple iPhones, navigation devices, iPads and smartphones and are included in the scope of delivery.The parking heater can also be operated while driving.Running time: The AUTOTERM parking heater switches off automatically after 2 hours of operation. However, as soon as you press a button during operation, the parking heater continues to run indefinitely until it is switched off manually.Scope of delivery:- AUTOTERM 2D parking heater 12 volt incl. silencer, intake air hose, heat protection hose, tank intake pipe and corrugated exhaust pipe.- Optionally analogue control unit simple control (PU-5) with rotary control or digital control unit comfort control (PU-29) with time switch- Nakatanenga parking heater console incl. the selected connections- Nakatanenga mounting plate- Fuel filler cap- Webasto air outlet with 60 mm connection, rotatable- 30 cm warm air pipe (diameter: 60 mm)- Vibration damper- Fixing material (screws, nuts, clamps, shrink hose, cable ties)Technical data:- Fuel type: diesel- Heating capacity: max. 1.8 kW, min. 0.8 kW- Volume of heated air: max. 75 m³/h, min. 34 m³/h- Fuel consumption in operation: max. 0.24 l/h, min. 0.1 l/h- Power consumption in operation: max. 29 W, min. 10 W- Weight: 3 kg (independent heater)- Manual start/stop → On the Autoterm.cz site you will find a calculator for the correct dimensioning of the air heater,You can choose between two control elements:- Simple Control (PU-5) element with rotary control: The old PU-10 control element had a relatively inaccessible control surface. Therefore, the reliable control element with rotary control is now the new improved standard of the Planar parking heaters! With the rotary control, you can adjust the heating power of the parking heater and regulate the power of the ventilation in ventilation mode! The PU-5 control element with rotary control can also be purchased separately here.- The digital control element comfort control (PU-29) with timer has an OLED display and an understandable and clear interface.  Temperature, ventilation and power can be configured via the display and the various buttons. With the timer, you can easily set the start of the parking heater to a specific time. The digital control element with timer can also be purchased separately here.Setting options comfort control (PU-29):- Temperature and power (adjustable for the parking heater, the control panel and for an external heater).- Time and date - Operating language (English or Russian)Functions of the timer comfort control (PU-29):- Memory function: save the time so that the parking heater starts at this time every day - Configurable memory locations: Up to 3 different weekdays with different times can be set and saved. The AUTOTERM (=Planar) 2D12 is equipped with an altitude kit.This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heat output decreases proportionally to the amount of oxygen in the air. Roughly speaking, from 2,000 metres the loss of output per 500 m altitude is approx. 5%. Manufacturer tests up to 3,440 m were trouble-free. Up to 4,000 m no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not yet be tested at real altitude. Important:Especially when used at high altitude, the free travel of the fan is extremely important!Route the combustion air intake and exhaust extremely short and with low resistance - i.e. no kinks, no blockage or reduction. It should also be noted that operation beyond 3,000 m is still a technical compromise. Again, care should be taken to ensure that the combustion chamber is properly heated on a regular basis. The chamber must be burnt free of soot deposits. Soot deposits can also form on heaters that are permanently operated at the lowest setting. Therefore, the following still applies: No guarantee for sooty combustion chambers!In order to ensure the longevity of the heater, you should also free-burn it occasionally at low levels. The combustion chamber reaches full temperature after running at full load for about half an hour. Normally, no further maintenance is required. In case of extreme loads, e.g. during longer overnight stays at more than 4,000 m, the combustion chamber including the seal set should be cleaned if necessary. To heat your roof tent using your auxiliary heating system, we offer an installation service for a warm air duct through a ventilation plate. https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Winch bracket Only a winch turns an all-wheel drive vehicle into a real off-roader. Anyone who has previously shied away from installing a winch on the New Defender (from 2020) because it detracts from the elegant design can now use the Terrafirma winch kit to install compact winches with a removable relay box so discreetly that they are almost invisible - without any loss of functionality. Detailed installation instructions guide you step by step through the removal of the original body parts, any necessary modifications, the installation of the Terrafirma mounting kit and the final re-installation of the original panels and covers. The winch control unit is relocated to the engine compartment. The kit includes all the necessary materials for mounting and electrical installation as well as the corresponding templates for modifying the covers.   Here are the dimensions of a suitable cable winch. You can use these dimensions to judge whether your desired cable winch can be installed: Caption

ExRoof roof rack for Ford Ranger Double Cab (year of construction 2016 to 2022)   The ExRoof roof rack is your perfect everyday companion! Thanks to its all-round profile rail, add-on parts can be attached using sliding blocks. The ExRoof is made of powder-coated aluminum and therefore weighs only 20kg. With a size of 1600mm x 1250mm x 49 mm, you have enough space to store your accessories.   Technical data: - Material: Aluminum 6063 - Weight: 20 kg - Surface: Powder coating - Size: 1600 mm x 1250 mm x 49 mm   Scope of delivery - Base carrier - Roof rack feet - Fastening material and installation instructions   Caution: Static load capacity: 300 kg Dynamic load capacity: 100 kg   The dynamic load capacity is not the manufacturer's approval. The manufacturer's load capacity must not be exceeded. The static load indicates the load capacity when stationary.   The dynamic load capacity refers exclusively to paved roads. The load must be evenly distributed over the entire surface.    

ExRoof roof rack for Mitsubishi L200 (from model year 2016)   The horntools ExRoof roof rack is your perfect everyday companion! Thanks to its all-round profile rail, add-on parts can be attached using sliding blocks. The ExRoof is made of powder-coated aluminum and therefore weighs only 20kg. With a size of 1600mm x 1250mm x 49 mm, you have enough space to store your accessories.   Technical data: Material: Aluminum 6063 Weight: 20kg Surface: Powder coating Size: 1600mm x 1250mm x 49 mm Scope of delivery Base carrier Roof rack feet Fastening material and installation instructions Caution: Static load capacity: 300 kg Dynamic load capacity: 100 kg The dynamic load capacity is not the manufacturer's approval. The manufacturer's load capacity must not be exceeded. The static load indicates the load capacity when stationary. The dynamic load capacity refers exclusively to paved roads. The load must be evenly distributed over the entire surface.    

ExRoof roof rack for Volkswagen® Amarok Double Cab (from year of construction 2010 to 2022)   The horntools ExRoof roof rack is your perfect everyday companion! Thanks to its all-round profile rail, add-on parts can be attached using sliding blocks. The ExRoof is made of powder-coated aluminum and therefore weighs only 20kg. With a size of 1600mm x 1250mm x 49 mm, you have enough space to store your accessories.   Technical data: Material: Aluminum 6063 Weight: 20 kg Surface: Powder coating Size: 1600mm x 1250mm x 49 mm Scope of delivery Base carrier Roof rack feet Fastening material and installation instructions Caution: Static load capacity: 300 kg Dynamic load capacity: 100 kg The dynamic load capacity is not the manufacturer's approval. The manufacturer's load capacity must not be exceeded. The static load indicates the load capacity when stationary. The dynamic load capacity refers exclusively to paved roads. The load must be evenly distributed over the entire surface.   The manufacturer responsible for the modifications/conversions is horntools GmbH, not Volkswagen AG. Volkswagen AG accepts no responsibility or liability for any negative effects that may occur as a result of the modifications to the vehicle.    

ExRoof roof rack for Volkswagen Amarok (from model year 2023) The innovative horntools ExRoof roof rack is your perfect everyday companion! Thanks to its all-round profile rail, any attachments can be attached using sliding blocks. The ExRoof roof rack for the Volkswagen Amarok is made of powder-coated aluminum and therefore weighs just 33 kg. With a size of 1400 x 1280 mm, you have enough space on the ExRoof platform to mount a roof tent, transport boxes, tools and other accessories on the roof of your vehicle.   Practical accessories such as eyebolts, roof tent quick-release fastener, awning bracket & more are also available for the ExRoof roof rack.   Product highlights Roof rack uses the original mounting points, no drilling required Compatible with Volkswagen Amarok (from model year 2023) Aerodynamic deflector is included in the scope of delivery Technical data: Dimensions: 1400 x 1280 mm (platform) Weight: 33 kg (roof rack feet + roof rack platform) Surface: RAL 9005 powder-coated Scope of delivery Roof rack feet Roof rack platform Wind deflector Fastening material and installation instructions    

Roof rack ExRoof for Volkswagen Caddy V Standard, Cargo, California & California Camper - L1 / SWB (year of construction 2020 to today) Roof rack uses the original mounting points, no drilling required Compatible with all VW Caddy V L1 variants (Caddy V & Caddy V Cargo) Rubber pad between roof rack base and vehicle to protect against corrosion Two individual roof rack feet provide stability in a lightweight construction Many practical accessories available Dimensions: 1698 x 1350 mm (platform)   The innovative horntools ExRoof roof rack is your perfect everyday companion! Thanks to its all-round profile rail, any number of add-on parts can be attached using sliding blocks. The ExRoof roof rack for the Volkswagen Caddy V Standard, Cargo, California & California Camper (L1 / SWB) with short wheelbase is made of powder-coated aluminum and therefore weighs just 32 kg. With a size of 1698 x 1350 mm, the ExRoof platform gives you enough space to mount a roof tent, transport boxes, tools and other accessories on the roof of your vehicle.   Technical data: Dimensions: 1698 x 1350 mm (platform) Weight: 32 kg (roof rack feet + roof rack platform) Surface: RAL 9005 powder-coated Scope of delivery: Roof rack feet Roof rack platform Wind deflector Fastening material and installation instructions Installation info:   For the following model variants, the OEM railing of the vehicle must be removed before fitting the roof rack platform:   Caddy V California Caddy V California Camper Caddy V Life Caddy V Dark Label Caddy V Style Caddy V Family Caddy V Edition Caddy V PanAmericana Caddy V Cargo Edition Caddy V Cargo PanAmericana Attention: Not compatible with VW Caddy V Maxi variants    

Trailer hitch for Land Rover Discovery 3 & Discovery 4 & Range Rover Sport (from 2005) Detachable, lockable, not height adjustable, not for Canada/USA/Mexico models.

combiBOIL hot water boiler for campers - More heating options & functions thanks to full Autoterm integration combiBOIL - One boiler, all optionscombiBOIL is unique in its market segment in terms of quality and range of functions.It offers three different options for water heating: With an electric heating cartridge. Using hot air from a parking heater. Via integration into the engine cooling circuit / with a water heater The combination of these options offers maximum flexibility and efficiency in various areas of application. Monitored and controlled by Autoterm Comfort Boiler Control: The Autoterm Comfort Boiler Control control panel (a further development of the Comfort Control) is specially designed for Autoterm heaters and combiBOIL hot water boilers to work together.The integrated thermostat function in the versions with 12V /230V heating elements enables extremely convenient and safe operation of the hot water system. All heating control options are retained. Your advantages: Display of the water temperature in real time, even on the SleepScreen Water temperature can be preset from 50 - 80 °C Adjustable hysteresis to 5 - 25 °C from the target temperature Overheating protection (configurable): Heating switches off automatically before the water temperature reaches a critical point. Normally, a control flap is no longer required to regulate the boiler. Frost protection: If the water temperature drops to 2 °C, the heating system automatically heats the water to +15 °C and the ambient air to +7 °C. The boiler and water pipes are reliably protected against frost damage. The Autoterm Comfort Boiler Control is only available as an option in combination with the combiBOIL hot water boiler - please select accordingly when ordering. Note:Autoterm Comfort Control and Autoterm Comfort Boiler Control differ in terms of hardware and software. The standard Comfort Control cannot be updated to the boiler monitoring functions.Goodbye control flapThanks to the possibility of controlling and monitoring the boiler temperature, regulation via a Y-piece / control flap is finally superfluous. Before a critical temperature is reached, the heating can be automatically switched from the current heating mode to ventilation in order to lower the boiler temperature. The rapid cooling achieved in this way enables the heating mode to be restarted before a clearly noticeable reduction in the room temperature occurs.A control damper may still be useful only in the case of extreme temperature requirements (e.g. sub-zero temperatures in the double-digit range with sub-optimal thermal insulation). Couple or large family - as much hot water as you needThe combiBOIL is available in three sizes. With volumes of 7, 9 or 12 liters, it always heats enough hot water, but not unnecessarily much. At a temperature of just under 60 °C in the boiler, 7 liters of water provide enough pleasantly tempered shower water for two people. Use with other heatersIt is not absolutely necessary to use an Autoterm heater to operate the combiBOIL hot water boiler. The hot air flow for hot water production can also be generated by other heaters.In this case, however, the integration of temperature measurement and the corresponding safety functions must be dispensed with, as the use of the Autoterm control panel requires connection to a corresponding heater. A control flap and its manual operation are then a prerequisite for safe operation.

Low running board round tube for four-door Defender 110 from 2003 onwards Low running board for four-door Defender 110 from 2003 onwards The running boards are at the original height (i.e. at the same height as the original Land Rover running boards) and therefore under the body.The running board is black powder-coated and provides a safe step thanks to checker plate supports - even with dirty pipes.Supplied in pairs.You can find a suitable crossbar here.

Aluminum cases Pro There are many aluminum cases, but just one “Alubox”. The Wiberg family’s business on Zealand in Denmark has been supplying the Danish military, various rescue services, international expeditions and the off-road community since 1999 with tough, handmade transport cases made from aluminum alloy AW-5754. As you would expect from real Vikings, Danish Aluboxes are seawater resistant. In addition, they can be padlocked, are dust-proof and highly resistant to corrosion and chemicals. The Wibergs’ experience and their commitment to continuously improve the Aluboxes show in the details: extra-robust and impact-proof stacking corners provide tight connections when you put several boxes on top of each other. Spring handles retract, so they’re never sticking out as dangerous obstacles‚ causing damages or injuries. Aluboxes are now made with solid rivets for even greater robustness and durability, even in extreme conditions. The new transport box for the 30-second touring tents by OZtents was developed by Soren Wiberg, who is a big fan of Land Rovers and camping. That’s why he saw right away that the somewhat flimsy OZtent carry bag needs to be improved upon. With packing dimensions of roughly 2 m, OZtents are usually too long to be stowed inside smaller 4x4s. The new Alubox measures 2130 x 510 x 220 mm, making it the ideal storage space for OZtent models RV1, RV2, RV3, RV4 und RV5. The transport case is designed for roof racks, like our very own CargoBear. And if you can fit a tent in your Alubox, you can also fit many other long and unwieldy pieces of equipment: shovels, sand ladders, snow chains and everything else that’s needed on expeditions and camping trips. One more thing: The Wiberg Vikings’ Alubox slogan is “Battered, beaten and still going strong.“  And that’s how we see it, too, when it comes to aluminum cases. Dents, scratches and bruises are at the end of the day part of the deal. They speak of your adventures and that’s why we keep unnecessary and environmentally harmful packaging to a minimum when we are shipping them. Material:Aluminium AW-5754, waterproof / dustproof according to IP54 standard Dimensions:2130 x 510 x 220 mm Please note that there is one important consideration about aluminum. As always, we make sure our products are stored, handled and shipped with the utmost care. Aluminum boxes, however, can always show minimal scratches, dull spots, blemishes, small dents or other superficial marks on delivery. These are solely due to the specific properties of the material. On contact with atmospheric oxygen, aluminum develops a natural, anti-corrosion patina.  Three times lighter than steel, it is also considerably softer, making it the perfect material for metal sheets, especially when weight and durability are important. The flip side of these properties, though, means that aluminum can never be entirely free of scratches, blemishes etc. This is why these surface marks do not constitute grounds for customer complaints. After all, aluminum boxes are meant to be rugged items for heavy duty use and every mark tells a story. With that in mind, we hope you get the most out of your boxes!

Technical data of the rope winch Alpha 9.5 - Working range voltage: 10-16Volt- Max. Power consumption 365A **- Train speed free of load 7m / minute- traction 4300kg **- 3-stage planetary gear 230: 1 geared down- Gross weight: 40kg- Net weight: 32.3kg- Weight with steel cable and roller cable window: 37.5kg- Series wound motor *- Drum (ØxLength): 63x226mm- Overall size (LxWxH): 577 x 160 x 225mm* Series motor with an electrically generated magnetic field** Values ​​can vary considerably, depending on the battery system, the winch can pull up to twice, the traction is designed for a standard 70AH battery. With more powerful battery systems, the pulling power must be limited by the current / voltage.The bundle consists of:1x horntools Alpha 9.5 electric winch with 4.3 tons traction1x Nakatanenga winch window1x winch hook1x winch rope (optionally in gray or orange)Please note that the depicted steel cable, the winch window and the winch hook from Superwinch are NOT included in the scope of delivery.

SUPERWINCH TIGER SHARK 9.5 The 12 V Superwinch Tiger Shark 9500 electric winch has a two-stage planetary gearbox. The winch is equipped with an automatic load holding brake with mechanical cone brake for large loads and a freewheel clutch for pulling the rope by hand. The Superwinch Tiger Shark 9.5 electric winch has waterproof sealed relays for high electrical currents, which allow for longer duty cycles.It is used for commercial recovery of rolling loads. Features: Rope speed: 5.7 - 1.2 [m/min]. Pulling force: 4,3 t Voltage: 12 V Weight: 41 kg Power consumption at full load: 340 A Scope of delivery:      1 x winch                optional: 1 x steel cable 8,3 mm/ 29 m or plastic winch cable 10 mm/30 m - optional in orange or grey     1 x winch hook     1 x roller window     1 x relay box     1 x battery cable     1 x cable remote control  

Defender 110 side storage box When you go on big adventures, every bit of storage space is useful, which means that not a single centimeter should be wasted.Our storage box makes ideal use of dead space. Made entirely of stainless steel and powder-coated in black, the storage box is waterproof, lockable and the ideal container for salvage materials, rubber boots or tools. The box fits perfectly for the sides of the Land Rover Defender 110 (2-door), but also for e.g. a motorhome, long-distance vehicle or other expedition vehicles.The open flap is held at a 90-degree angle by two thin steel cables and thus serves as a storage surface for water canisters, for example, or even as a small breakfast table. Supplied complete with 2 keys and all fixing materials.Internal dimensions of the side storage box: 465 mm x 285 mm x 335 mmPlease note:This side storage box can only be installed in front of the rear wheel arch in hardtop versions.  Merkblatt Edelstahl und Rost