Wiper arm cover cap for Defender LHD, BJ 2001-2016
Land Rover Cover Cap for Windscreen Wiper Arm for Defender 90/ 110/ 130 year of construction 2001-2016
Prices incl. VAT;
Wide door opening angle up to 95 degrees, stainless steel, Land Rover Defender 110/130CC
Wide angle stainless steel second row door stay brackets for Defender 110/130 CC Wide angle stainless steel second row door stay brackets for Defender 110 and 130 CC rear doors. Allow to open the door further (up to 95°). This does not only make entering and leaving the rear seats easier, also gives more access for drawers if rear bench is not fitted, e.g. for a cooler (we can make such drawers to order!). Also without any additional rear furniture loading is greatly facilitated. DIY fitting possible! Only takes a few minutes, the supplied fitting instrucions leave no questions open! No drilling of additional holes, bracket fits to original mountings. Set (for two doors) is supplied with stainless steel fixings, washers, anti-seize copper paste and fitting instructions. The kit fits all MY Defenders (TDi, TD5, TD4).
Prices incl. VAT;
Nakatanenga ventilation sheets - Citroen Berlingo / Peugeot Rifter / Opel Combo / Toyota Proace City Verso
Nakatanenga ventilation panels, rear side window The precisely fitting ventilation panels are ideal for high-roof combi vans such as the Citroën Berlingo, Peugeot Rifter, Opel Combo and Toyota Proace City Verso. These vehicles in particular are often used as family cars, campers or transport vehicles for dogs – and benefit greatly from good air circulation in the interior. The robust, aluminium-made and black powder-coated panels can be inserted into the lowered side windows in just a few simple steps. They reliably provide fresh air without allowing rain or insects to enter the vehicle, while also reducing the risk of unauthorised access. This keeps the interior pleasant even on warm days, whether you are on the move or stationary. Installation is straightforward: lower the window, insert the panel and raise the window again – done. ⚠️ Important note: Even with ventilation panels in place, children and animals must not be left unattended in the vehicle. Suitable for: Citroën Berlingo K9 (2018 and later), Peugeot Rifter, including L2 seven-seater, Opel Combo and Toyota Proace City Verso (all from model year 2018 onwards) Note: only suitable for vehicles with optional equipment package (sliding doors in row 2 with lowerable side windows) Material: aluminium, black powder-coated Dimensions: 571 x 147 mm
Prices incl. VAT;
MOMO leather steering wheel cover, Defender
High-quality leather steering wheel cover - especially for MOMO steering wheel in the Defender Centre boss cover with original Land Rover badge for MOMO steering wheel, suitable for Land Rover Defender 90/110/130, made from genuine leather for superior feel and decorative stitching. Replaces the horn boss. Available in different colours. Comes with one set of stainless steel screws and one set of black screws. The steering wheel pictured is not included and is only shown for illustration. Different models available, please choose.
Prices incl. VAT;
Hinge pin ventilation flap Defender
Robust hinge pins for ventilation flaps Suitable for all Defender up to MY 2007Material: Stainless steelThe set consists of 4 bolts and 10 nuts (incl. 2 spare nuts).Please note: This set is not included in our stainless steel bolt set!
Prices incl. VAT;
Corner protectors for Defender seat box
Corner protector for Defender seat box The edge of the Defender seat box is susceptible to damage and sometimes looks quite pitted and unsightly after a while. With these elegant corner protectors, you can spruce up the seat box and protect it at the same time!Made of 3 mm black metal and CNC-milled to the highest precision. With the help of a cordless screwdriver and the included fastener, the corner protectors are attached in less than 5 minutes! The kit contains a pair of corner protectors and 12 pcs. 8x19 mm steel screws. The corner protectors also fit a Series II and III, but require a matching hole to allow the seat rail to be attached.Scope of delivery: One pair of corner protectors incl. fixing material. Illustrations may differ.
Prices incl. VAT;
Spacer for viscous fan for Land Rover Defender Td4
Effective cooling optimisation for Land Rover Defender TD4 2.4 - 25 mm spacer for viscous fan Spacer / distance piece for Land Rover Defender Td4 2.4 increases cooling output of viscous fan and thus prevents overheating in hot environments at slow speeds, heavy terrain or when pulling heavy trailers. Fitting of the 25 mm spacer is easy.
Prices incl. VAT;
Bumper protection for New Defender from MY2020, 3 colours
Bumper protection What’s worse than a scratch on your car? Clearly that very first scratch! How annoying is it when you spot one on a pristine new vehicle? Even when 4x4s generally wear their scars with pride, most signs of heavy usage aren’t necessary, they’re frustrating and also depreciate the value of your vehicle. One of the first areas to show signs of wear and tear – especially with off-road vehicles – is usually the cargo area. But if your 4x4 is a New Defender, would you really want to see a worn and scratched rear bumper? Immediate and long-lasting prevention of wear marks on your New Defender’s rear bumper can be achieved with our designated paint protection film. This high-performance product by industry leader 3M protects your New Defender’s rear bumper from scratches and abrasion even when your loading area is constantly in use for work or sports. And don’t forget the damage a dog’s claws can do to the paint when you carry them regularly in a dog box in the back. Due to its multi-layer structure, the 3M wrap also protects the bumper from chipping caused by the impact of small stones or dropped objects. Installing the paint protection film is really easy. Everything you need is included: cleaning cloth, adhesion promoter wipe, squeegee and detailed instructions. If you’ve never done this before: don’t worry. The protective wrap can be positioned exactly as you need it, but if you have to readjust the position a few millimeters that’s no problem either. Simply slide the film into place. It only starts to adhere once you apply pressure with the squeegee. The protective wrap is available in black, matt black, anthracite grey or silver, making it a perfect visual match for any New Defender color scheme. Comes in one complete „no worries“ kit: foil, squeegee, cleaner, primer.
Prices incl. VAT;
Window well trim for Defender
Window well trim for Defender Available in the following versions:- Window well trim (pieces) front left or right, for all Defender 90/110 (for 1x left and 1x right, simply order 2 pieces).- Window well trim (piece) rear left, for all Defender 110/130- Window well trim (piece) rear right, for all Defender 110/130
Prices incl. VAT;
Air intake cover for all Land Rover Defender models, set of 3, powder coated alloy
Air intake cover for all Land Rover Defender models (Tdi, Td5, Td4 2.4 and 2.2), set of 3, made of 2 mm aluminium to replace the plastic covers. Powder coated, comes with stainless steel fittings. Image similar
Prices incl. VAT;
RAM Mount ball and adapter for Land Rover Defender Td4 (from MY2007)
Perfect base for stable brackets RAM Mount ball and adapter (1" Size B) for passenger grab handle to mount smartphone, tablet, action cam, satnav, etc., for all Land Rover Defender Td4 (from MY 2007). It is possible to fit two of these adapter to the grab handle, e.g. for mounting a tablet device for navigation alongside your smartphone. Supplied with fixings but without further holders. Suitable RAM Mount device holders can be purchased seperately. All pictured items apart from the actual ball and fixings are for illustration purposes only. For orders to the USA please contact seriesdefender.com and for orders to Canada rovalution.ca/
Prices incl. VAT;
LED signal light for Land Rover Defender, position light, white
LED parking light in white for Land Rover Defender - Signal light White LED parking light for Land Rover Defender, single.with E-approval mark and fittings Also have a look at our bundles with all signal lights at a saving: LED signal lights for Land Rover Defender If the lamps on the existing vehicle are square at the rear, you need 1x AMR3850 mounting base per lamp to mount the new round LED lamps. As a rule, the original drill holes can be used. Please note: The screws must not be over tightened (only hand-tight!), Otherwise the plastic housing may crack. These cracks could allow water to penetrate into the generally watertight luminaires. Use only a screwdriver and NO cordless screwdriver!
Prices incl. VAT;
LED licence plate light for Land Rover Defender - OEM looks
Our LED licence plate light for Land Rover Defender 90/110/130 looks like the original item with all the benefits of LED technology: whiter and brighter than halogen bulbs little current drain (only 0.5 W), generates little heat insensitive to vibrations, especially interesting for diesel powered cars! superior longevity large voltage range - 9-33 V The light is E-marked for legal use (corresponding to ECE regulation no. 4). It's water and dustresistant to IP67 and is fitted using the existing M5 screws. All fittign material is supplied, so fitting only takes a few minutes.
Prices incl. VAT;
LED Indicator relay 12V for Land Rover Defender
Flashing - LED 12V The four-pole relay for LED direction indicators prevents the indicators from flashing too quickly and allows the frequency of the indicators to be adjusted. It replaces the factory-fitted relay in the Land Rover Defender 90/110/130. To "activate" the LED indicator relay, the hazard warning lights must first be briefly activated after installation. Then use the rotary control to adjust the relay so that the trailer coupling indicator light goes out in left/right mode.
Prices incl. VAT;
High-Lift Jack Adaptor for Land Rover Defender
Hi-Lift / JackAll Adapter for Land Rover Defender – Secure Hold for Heavy-Duty Tasks When the going gets tough off-road or maintenance work is due on your Land Rover Defender, a reliable jack like the Hi-Lift or JackAll is worth its weight in gold. However, to transfer its power safely and gently to the vehicle, the right adapter is required. The Nakatanenga Hi-Lift / JackAll Adapter has been specially developed for the original jacking points on the Land Rover Defender (90/110/130) and ensures safe and stable lifting of your vehicle. This robust adapter is simply attached to the lifting jaw of your Hi-Lift, JackAll, or a similarly constructed farm jack and inserted with a precise fit into the designated jacking points in the chassis or on appropriately equipped bumpers and sill protection tubes of your Defender. This effectively prevents the jack from slipping and minimises the risk of damage to the vehicle. Manufactured for demanding off-road use, this adapter impresses with its solid construction and durability – typical Nakatanenga quality. It is an indispensable accessory for every Defender owner who values maximum safety and efficiency when using their farm jack. The Advantages at a Glance: Safe Lifting: Provides a stable and secure connection between the jack and the vehicle. Perfect Fit for Defender: Designed for the original jacking points of the Land Rover Defender 90/110/130 as well as for many aftermarket bumpers and rock sliders with corresponding mounts. Protection for Your Vehicle: Reduces the risk of slipping and damage to the chassis or attachments. Robust Construction: Designed for tough off-road conditions and frequent use. Universally Applicable: Suitable for Hi-Lift, JackAll, Hilift, Jack-All, and similarly constructed farm jack models. Easy to Use: Quickly and easily attached to the jack and positioned on the vehicle. Technical Details : Material: High-strength steel Surface: Corrosion-resistant coating Scope of Delivery: 1x Hi-Lift / JackAll Adapter for Land Rover Defender Trust in proven Nakatanenga quality and equip your Land Rover Defender with this essential adapter for the safe use of your Hi-Lift or JackAll jack. Indispensable for every off-road tour and workshop. Note: The jack shown is not included in the scope of delivery.
Prices incl. VAT;
Installation kit Suzuki Jimny GJ / HJ with Nolden 90mm combination fog light with daytime running light
Installation kit Suzuki Jimny GJ / HJ with Nolden 90 mm combination fog lights/daytime running lights Especially with hard-working off-road vehicles such as the Suzuki Jimny GJ, it is worthwhile converting completely or partially to LED headlights and lamps: they generally provide better light output, are less susceptible to damage and have a longer service life. With our complete installation kit consisting of Nolden 90 mm LED combination lights for daytime running lights and fog lights and the matching adapter cable, burnt-out, corroded or broken bulbs are a thing of the past. The Nolden combination lights combine both a daytime running light ring with fibre optic technology and an LED fog light in a high-quality chrome housing. Nolden uses high-quality LEDs from Osram, which are also extremely economical at 8.1 W for the daytime running light and 8.8 W for the fog light. Installation of the LEDs is extremely simple, with the appropriate adapter cables from PS13W socket to AMP Superseal plug for the daytime running lights included. The fog lights are plug & play. If you only need the adapter cables, you can find them here. The complete installation kit consists of two adapter cables and a set of Nolden 90 mm LED combination lights daytime running lights/fog lights. Scope of delivery: 1 x pair of Nolden 90 mm LED daytime running/fog lights chrome Adapter: 2 pieces PS13W socket 2-pin to AMP Superseal plug 3-pin. Note: The headlights also fit various Subaru models (including the Subaru Levorg), which are equipped with 90 mm combination headlights (fog and daytime running lights) as standard. Depending on the vehicle, it may be necessary to repin the plus and minus wires on the wiring harness for the daytime running lights (the easiest way to do this is at the Superseal connector).
Prices incl. VAT;
LED festoon bulb, 39mm, for Land Rover Defender 90/110/130
Bright, white light with minimal power consumption and a long service life - LED soffits make it possible! LED soffits for the Defender - Simple. Fast. Impressive. Do you love your Defender, but the interior lighting leaves a lot to be desired? With our new LED soffit, you can bring the latest lighting technology into your vehicle - and it's plug & play! The durable and vibration-resistant 39 mm LED soffit is a direct replacement for the bulb in the standard interior light(s) in the Land Rover Defender 90/110/130. Why an LED soffit? Our LED soffit has been designed to give you brighter, more efficient and stylish lighting. It's a perfect upgrade. Plug&Play - It couldn't be easier! No long installations, no tangled cables, no specialist knowledge required! Our LED soffit can be installed in just a few minutes. Simply remove the existing interior light, plug in the LED soffit and you're done. The plug & play system makes it possible - even for beginners. Advantages at a glance: Bright, uniform illumination: Thanks to state-of-the-art LED technology, the base centre provides pleasant, bright lighting in the interior.Daylight white; light colour 6000 KelvinVoltage: 12 V Energy-efficient: LEDs consume less power than conventional light bulbs, saving your Defender's battery. Durable: LEDs have a significantly longer service life and are resistant to vibrations and shocks. Easy installation: No workshop required - you can install the Soffitte yourself in just a few minutes.Ready to install - plug & play Who is the LED soffit suitable for? Our LED soffit is the perfect solution for all Defender fans. It is suitable for the Defender 90 as well as for the Defender 110 and 130. Please observe the polarity when installing! Scope of delivery: 1 piece
Prices incl. VAT;
Elevated air intake / snorkel for Land Rover Defender
Take a Deep Breath – with the Raised Air Intake for Your Land Rover Defender! Your Defender is built for adventure. But what if those adventures take you through deep water crossings or extremely dusty tracks? This is precisely where our raised air intake, also known as a snorkel, comes into play and becomes an indispensable companion for your Land Rover Defender 90, 110, or 130. Imagine crossing a river. With a standard air intake, you risk water getting into the engine – an expensive problem you can avoid. Our raised air intake relocates the intake point to roof height. The result: a significantly reduced risk of engine damage from water. But that's not all! The snorkel also shows its strengths in dry, dusty regions. The air at roof height is cleaner and contains fewer dust particles than near the ground. This means your air filter gets dirty slower, needs to be cleaned or replaced less often, and your engine can breathe more freely. This snorkel, made of robust black plastic, even comes with an integrated cyclone filter that pre-separates coarse particles, further increasing efficiency. Installation is on the right side of the vehicle, and thanks to the EU-wide valid TÜV parts certificate, registration is no problem either. So, you're not only safer but also legally on the road. Your advantages at a glance: Optimal Engine Protection: Significantly reduces the risk of water damage during river crossings. Cleaner Intake Air: Less dust and dirt enter the engine, which protects your air filter and extends its lifespan. Integrated Cyclone Filter: For even more effective pre-separation of dirt particles. Robust Design: Made from durable, black plastic. TÜV Parts Certificate: For hassle-free registration (valid EU-wide). Perfect Fit: Suitable for Land Rover Defender 90/110/130, models 300Tdi, Td5, Td4 2.4 & Td4 2.2 (Puma/TDCI). Easy Installation: On the right side of the vehicle. Equip your Defender for real challenges and ensure it always gets the best air to breathe. With this raised air intake, you're prepared for any terrain! With EU-wide valid TÜV parts certificate! Suitable for Land Rover Defender 90/110/130, 300Tdi, Td5, Td4 2.4 & Td4 2.2 (Puma/TDCI)
Prices incl. VAT;
Wind Deflector ClimAir Land Rover Defender to MY 2016, front
Wind Deflector ClimAir Land Rover Defender to MY 2016, Front Off-road vehicles are not designed for aerodynamically perfect airflow. So far, so obvious and normally it doesn’t matter anyway because in a 4x4 you’re unlikely to reach the speeds where it becomes problematic. But there is one aspect where the rustic box shape of Defender does show the effects of aerodynamic neglect and that’s the nearly rectangular shape and the straight and vertical positioning of the windows. There’s more than one reason in a 4x4 to crack your windows a little, whether you’re off-roading or it’s cold and wet. Your classic Defender’s windows for instance are misting up because the ventilation famously isn’t up to the job of defogging them. And that’s when you see the effect we’ve talked about in the beginning. The drag around the cracked windows is not only loud, it also pulls more dust and water inwards and that’s pretty annoying, even for hardcore off-roaders. Wind deflectors by ClimAir for Defender, offer the perfect solution. Their tailor-made fit and robust build guarantee improved intake of fresh air and better climatic conditions inside the vehicle all year round while protecting the windows. Made from high-quality acrylic glass, the deflectors reliably keep out rainwater and snow, whether the car is being driven or parked somewhere. On hot days, you can prevent heat build-up in the car by leaving the window cracked open – a huge improvement for children and pets alike when travelling or while waiting in a carpark. Smokers and especially their passengers will also appreciate the fresh air. ClimAir wind deflectors are available in transparent, smoke grey or black and come with German type approval (ABE). Fitting them is easy and only a question of minutes. The manual is included. Deflectors are sold in pairs for front and rear doors respectively and have to be ordered separately.
Prices incl. VAT;
NOLDEN 7" Bi-LED main headlights Generation 2 for Land Rover Defender
Nolden 7-inch Gen 2 Bi-LED Headlights: Illuminate the night and give your Defender the ultimate look! Now also available in All-Black = Stealth Edition! Do you love your Land Rover Defender, but the original headlights let you down in the dark or bad weather? Then it's time for an upgrade that not only provides brilliant illumination but also gives your off-road classic a modern and premium touch: the Nolden 7-inch Generation 2 Bi-LED Reflector Headlights! More light, more safety, more style – for your Defender: These high-end headlights are the result of German engineering and set standards in terms of light output, durability, and design. Say goodbye to dim halogen light and experience the road and terrain ahead in a whole new clarity. Brilliant Bi-LED Technology: Experience significantly brighter and more uniform illumination than with conventional headlights. The Bi-LED function combines low beam and high beam in one module, ensuring a seamless transition and impressive range. This means for you: You see obstacles earlier and drive safer – whether on a dark country road or in the deepest terrain. Plug & Play Installation: Developed as a direct replacement for your Defender's original 7-inch headlights. Installation is straightforward and requires no complex vehicle modifications. Extremely durable and maintenance-free: LED technology is not only more energy-efficient but also significantly more durable than halogen lamps. No more annoying bulb changes! These headlights are built to withstand the harsh conditions your Defender is exposed to. Modern look with a classic touch: The Nolden headlights blend perfectly with the Defender's iconic design while giving it a modern, high-quality appearance. The clear lens and thoughtful reflector design make them a real eye-catcher. (Depending on the chosen variant, e.g., in Chrome, you further enhance the premium look). With E-certification mark – road legal: Naturally, these premium headlights have the necessary E-certification, so you can drive legally and without concerns on public roads. Features at a glance: State-of-the-art Nolden LED low beam and high beam, LED daytime running light, and position light in fiber optic technology Significantly improved light output and visibility Perfect fit for Land Rover Defender (replaces original 7-inch headlights) Long lifespan and high energy efficiency Weather-resistant and robust Elegant design that enhances your Defender With E-certification mark for legal road use Treat your loyal companion to the light upgrade it deserves! With the Nolden 7-inch Generation 2 Bi-LED Headlights, you invest in safety, durability, and an unbeatable look. Turn night into day and enjoy every drive with perfect visibility! A few more details: Over 30,000 hours LED lifespan White road illumination, similar to Xenon H4 connectors for Plug & Play Standard 7” mounting (PAR56) Die-cast aluminum housing 480 h salt spray test Available in Chrome, Dark Chrome, Matte Black, and All-Black Approvals: ECE and EMC Technical Data: Low beam: 23 W High beam: 33 W Daytime running light: 8.5 W (fiber optic) Position light: 1.2 W (fiber optic) Dimensions: 177 mm LED Type: OSRAM Voltage: 12/24 V Weight: 880 g Tested: ECE, EMC Ventilation: Nitto Denko Air Cap Housing material: Diallyl Diglycol Carbonate (ADC) Lens material: Hardened PC (Polycarbonate) Temperature range: -40°C to +80°C Vehicle wiring: FLRY Connector: H4 for main headlight, Tyco/AMP Superseal for position light Reference number: 12.5 The Nolden LED headlights are available in Chrome, Dark Chrome, and Matte Black and are delivered with a cable set for position and daytime running lights. The set includes 2 headlights and 2 stainless steel mounting rings. Should you also want to replace the mounting kit during the headlight change, we have the following products for you: lighting/accessories/2735/headlight-mounting-kit lighting/accessories/2736/headlight-mounting-kit-for-land-rover-defender-with-stainless-steel-screws
Prices incl. VAT;
Switch for indicator high beam horn - for Land Rover Defender
Switch for indicators, high beam and horn for Land Rover Defender suitable for Land Rover Defende from VIN ...WA138480 (Defender TD5 from MY1998) to FIN ...EA999999 (Defender TD4 up to MY2014)
Prices incl. VAT;
Service Kit OE for Land Rover Defender Td5 and Discovery Td5
Service kit OE for Land Rover Defender Td5 & Discovery Td5 - maintenance in original equipment quality Our high-quality service kit offers you all the important components for the regular maintenance of your Land Rover Defender Td5 or Discovery Td5. Included are an air filter, main flow oil filter, rotor filter, diesel filter and the appropriate seal for the oil drain plug - all in proven OEM quality. This ensures that your vehicle remains reliable and powerful. Ideal for the next inspection or when changing the oil yourself.
Prices incl. VAT;
Gasket set for Alpine windows for Defender from MY1990 to 2016
Gasket set for Alpine windows for Defender from MY1990 to 2016 Usually suitable for Defender from MY1990 onwards here the 4mm thick window was installed ex works (the thicker window with 5mm was usually only installed on series and Defender up to MY1990). If you are unsure, measure the thickness of the disc. Scope of delivery: 1 piece gasket for Alpine window 1 piece filler strip for Alpine window
Prices incl. VAT;
Nakatanenga ventilation panels, rear side window - Land Rover New Defender from MY2020
The new Defender combines modern technology with proven off-road capability. Good air circulation as if the windows were slightly open, but without the risk of rainwater or theft? Plus effective protection against insects? That's what our ventilation panels with mosquito nets offer, made to fit the New Defender perfectly from high-quality aluminum—no wobbly universal parts. Supplied in pairs and powder-coated in black, they complement the modern design discreetly and sensibly, especially when camping or on expeditions. Installation is straightforward: roll down the window, insert the ventilation panel, close the window again – and it sits securely and rattle-free. ⚠️ Important note: Children and animals must never be left in the vehicle at high temperatures, even with the ventilation panels in place. Suitable for Defenders built from 2020 onwards. Length: 550 mm
Prices incl. VAT;
Stainless Steel Bolt Kit for Front Bumper Defender 90/110/130
Fits all MY - TDi, TD5, TD4 2.4, TD4 2.2 with original-bumper Full bolt kit for one bumper - stainless steel bolts for Defender 90/110/130, comes with assembly paste. Do not use in conjunction with a winch or clevis pin bumper!
Prices incl. VAT;
Greasable track rod ends for all Land Rover Defender
Greasable track rod ends for all Land Rover Defender Greasable track rod ends for original track rod of Land Rover Defender 90/110/130. The set comprises three track rod ends, two with right-hand thread and one with left-hand thread, which can be greased with a grease gun. In contrast to the non-greasable OEM track rod ends, these suffer from much less wear and thus last much longer.
Prices incl. VAT;
A-pillar grab handle, for Land Rover Defender MY1987-2016, colour: silver or black
A-pillar grab handle The easy-to-fit, stylish A-pillar grab handle makes it easier to get in and out of Defender. The handles are made from anodised aluminium. Available in black or silver Scope of delivery: 1 piece grab rail, fixing material.
Prices incl. VAT;
Windscreen Bracket Kit for Land Rover Defender
Windscreen Bracket Kit for Land Rover Defender The original windscreen support brackets on the Defender are one of those details on the car that sooner or later cry out for cosmetic surgery. All kinds of corrosion – by exposure, metal contact, environmental or automotive chemicals – affect the parts and simply make them look shabby. The result is rust, peeling paint and streaking on the bodywork. Fortunately, replacing the brackets is one of the easiest jobs on the Landy. Our replacement brackets are available in two versions: black powder-coated or anodized aluminum. Both processes - anodizing and powder coating - ensure extremely resistant and durable sealing of the aluminum parts. During anodizing, electrolysis creates a porous surface structure, which is particularly suitable to absorb color pigments. In a last step, the anodizing is then compacted and thus sealed. However, black anodized aluminum tends to fade, which is why we have opted for powder coating for the deep black option. If you’re aiming for a look other than black or aluminum gray, you can of course paint it yourself or have it painted. You can also achieve your desired custom effect with our range of RAPTOR products. Or simply order the parts right here in the store with black powder coating from a professional for little extra cost. Suitable for all Land Rover Defenders 90/110/130. Supplied in pairs, gaskets and mounting materials are included.
Prices incl. VAT;
Nakatanenga ventilation plates rear side windows - Ineos Grenadier
Ventilation plates rear side windows - Ineos Grenadier The INEOS Grenadier stands for uncompromising off-road capability and robustness. Good air circulation, as with slightly open windows, but without the increased risk of rainwater ingress or theft? Plus effective insect protection? That's exactly what our ventilation panels with mosquito netting offer, precision-manufactured for the Grenadier from high-quality aluminium — no rattling universal parts. Supplied in pairs, powder-coated in black and visually unobtrusive, they are ideal for expeditions, camping and tough use. Installation: wind down the windows, insert the panels, wind up the windows. Installation is straightforward: roll down the window, insert the ventilation panel, close the window again – and it's securely in place without rattling. ⚠️ Important note: Children and animals must never be left in the vehicle at high temperatures, even with the ventilation panels in place. Length: 520 mm <iframe width="560" height="315" src="https://www.youtube.com/embed/qWKDhVh_0n0" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>
Prices incl. VAT;
Nakatanenga Military Snow Cover - Stainless Steel
Stainless steel cover for air intake Military snow cover from stainless steel exclusively for Nakatanenga fits Land Rover Defender 90/110/130 (all model years) and reliably prevents the ingress of water, snow or dead foliage into the heating system. If independent vehicle heating is fitted, this will also always get enough clean air to work properly. Originally developed for the military Wolf-type Defenders, this military snow cover is also highly useful for civilian vehicles. The sturdy cover can be stepped on and is available for LHD and RHD vehicles. It can be fitted with or without chequer plate wingtop protection. Fitting simply means swapping the original cover and attaching the MSC with the six supplied stainless steel screws. Takes about 10 minutes. A new seal is supplied, too. Please choose desired type.
Prices incl. VAT;
Stainless Steel Bolt for Defender NAS Roll Cage
Perfect fit & maximum corrosion resistance - High-quality stainless steel screw for Defender NAS cage The Stainless Steel Bolt corresponds to the Land Rover part number ALR5549. With the Stainless Steel Bolts you can mount the NAS Roll Cage to the Defender. Please mind that you need at least approx. 70 Bolts for one Roll Cage. Material: Stainless steel A2-80 high-strengthLength (l): 30 mmDiameter (d): 10 mmTorx-profile: TX50 The black stainless steel screws were coated with a chromium-oxide layer via a computer-controlled electrochemical process. As a result, the stainless steel screws are still protected against rust.
Prices incl. VAT;
Black Heritage Headlight plates (with inlet gills) in aluminium, powder coated
Heritage-style headlight surrounds in black aluminium Matching to our black Heritage grille:Black headlight plates with inlet gills and silver OR black powder coated headlight rings.The plates are manufactured EXCLUSIVELY for us and UNIQUE in their looks! Material: high-strength aluminium, black powder coated 1 pair plates with headlight rings and stainless steel mounting kit for every Land Rover Defender 90, 110 or 130.
Prices incl. VAT;