POWERspec TDI 200/300Tdi At LOF Clutches, POWERspec is the next step up from ROADspec when it comes to performance. If you tow regularly or carry extra weight like expedition trucks do then this is the spec for you. It’ll handle highly tuned road monsters or hard worked off-roaders all day long. If you want reliability and drivability from your mapped motor POWERspec will keep you moving forward!  This kit features heavy duty friction material, a high torque sprung center hub as well as the updated release bearing and the slave cylinder for the 2.2l engine. And by the way, the pedal weight is not heavier than the original. The POWERspec clutch kit is suitable for vehicles with tuned injection pumps (boost pin/spacer), but not suitable for VNT turbo engines, please see 2.8 TGV HS INTERNATIONAL CATEGORY.  Description: LOF heavy duty friction material High torque sprung center hub LOF Clutches EXTREMEspec release bearing G90 High-temp assembly grease CNC wire-formed bearing retaining clip CNC wire-formed pushrod retaining clip High tensile bolt pack for clutch cover 1x OEM spigot bush 1x OEM fork bush Pedal weight not heavier than original  Note from LOF: if this clutch is newly installed, the LOF Powermaster clutch master cylinder should not be installed as well.  

POWERspec Series III At LOF clutches, POWERspec is the next step up from ROADspec when it comes to performance. If your Series III Land Rovers tows regularly or carries extra weight as an expedition truck then this is the spec for you. It’ll handle highly tuned road monsters or hard worked off-roaders all day long. If you want reliability and drivability from your mapped motor POWERspec will keep you moving forward!  This kit features heavy duty friction material, a high torque sprung center hub and an EXTREMEspec release bearing for heavy duty tasks.  Description: Heavy Duty thermofiber friction naterial High torque sprung centrer hub LOF Clutches EXTREMEspec release bearing G90 high temp assembly grease syringe CNC wire-formed bearing retainer clip High tensile bolts

saving bundle: Heavy Duty clutch kit incl. Improved MT82 intermediate shaft for TD4 saving bundle consisting of automatic clutch, friction disc, release bearing, matching clutch slave cylinder and a reinforced intermediate shaft MT82 transmission. For TD4 built in 2007-2016 Information about the clutch automat with friction disc, release bearing and clutch slave cylinderEspecially with switching operations under higher load, such in trailer operation or in performance-enhanced vehicles, enormous forces must be transmitted by the clutch. A common problem with the Defender's original clutch is the failure of the insufficiently sized torsion springs. The torsion springs, specially adapted to the Defender Td4, eliminate the familiar problems of clattering or jamming clutches. Another, but less common, problem is the ingress of oil from the engine or transmission into the clutch bell. This oil is absorbed by the porous friction linings and occurs during driving by the resulting frictional heat repeatedly to the friction lining. Due to the reduced traction it comes in the episode to a higher heat development and vitrification of the coverings. The heat is a measure of the converted energy that is no longer available to the drive! The organic coating used in this coupling can not absorb oil and therefore does not vitrify. It convinces with specially adapted friction modifiers with a soft response and enables a 100% adhesion. Of course, the pads are asbestos- and lead-free, free of other toxic heavy metals and heavy metal compounds. Information on the reinforced intermediate shaft for MT82 transmissions.Improved intermediate shaft for MT82 transmission in Land Rover Defender TD4 / TDCi / Puma 2.4 / 2.2 Known problem: The intermediate shaft of the TD4 / TDCi / Puma 2.4 / 2.2 models is not greased and is not supplied with oil. The connection of the two-piece intermediate shaft wears after prolonged use, since the shaft with outer ring gear has direct contact with the shaft with inner ring gear. In the worst case, this wear ensures that the sprocket shears off and the vehicle thus stops. A regular lubrication of the sprocket helps, but is in the long run very cumbersome Our solution: The improved intermediate shaft is supplied with the oil of the gearbox and thus prevents the wear of the shafts. Easy and uncomplicated! We recommend replacing the pilot bearing when replacing the coupling. Please note:  Before installing the clutch, the dimension of the following step must be measured on the flywheelIf the dimension is 25.4 mm, the clutch can be installed.If the measurement is 22.2 mm, a Ford flywheel is installed. The clutch is not compatible with this and will malfunction sooner or later.If a Ford flywheel with a measurement of 22.2 mm is installed, you will also need the following Land Rover flywheel.

Heavy Duty Clutch Kit for Land Rover Defender TD4 Especially with switching operations under higher load, such. in trailer operation or in performance-enhanced vehicles, enormous forces must be transmitted by the clutch. A common problem with the Defender's original clutch is the failure of the insufficiently sized torsion springs. The torsion springs, which are specially adapted to the Defender Td4, eliminate the familiar problems with clattering or jamming couplings. Another, but less common problem is the ingress of oil from the engine or transmission into the clutch bell. This oil is absorbed by the porous friction linings and occurs during driving by the resulting frictional heat repeatedly to the friction lining. Due to the reduced traction it comes in the episode to a higher heat development and vitrification of the coverings. The heat is a measure of the converted energy that is no longer available to the drive!The organic coating used in this coupling can not absorb oil and therefore does not vitrify. It convinces with specially adapted friction modifiers with a soft response and enables a 100% adhesion. Of course, the pads are asbestos- and lead-free, free of other toxic heavy metals and heavy metal compounds. Complete set consisting of automatic clutch, friction disc and release bearing. Clutch kit with clutch slave cylinder for Defender TD4 from year of construction 2007-2016 We recommend replacing the pilot bearing when replacing the coupling.Please note:  Before installing the clutch, the following dimension must be measured on the flywheel If the dimension is 25.4 mm, the clutch can be installed. If the measurement is 22.2 mm, a Ford flywheel is installed. The clutch is not compatible with this and will malfunction sooner or later. If a Ford flywheel with a measurement of 22.2 mm is installed, you will also need the following Land Rover flywheel.