Automotive engineering
GIRLING shock absorber, front for Land Rover, short wheelbase
Girling shock absorber, front For front, short wheelbase For the following series: Series I - 1954-1958 Series II Series IIA Series III These traditional hydraulic shock absorbers feature fluid and seal technology to keep your Land Rover suspension under control.
Prices incl. VAT;
LOF Clutches POWERslave clutch slave cylinder for TD5
POWERslave for Td5 Discovery and Defender Heavy clutches with high pedal weight are a known phenomenon especially in Td5 Defenders (1998-2006) but also in many Td5 Discovery models (1998-2004). But there’s a simple and cost-effective solution for anyone experiencing problems with the heavy pedal. Installing a POWERslave slave cylinder will reduce the pedal weight by up to 30% in comparison to the original set-up. Please note: the POWERslave cylinder lowers the biting point of the clutch. On Defenders, the biting point can be adjusted in the pedal box. On Discovery 2 models, where the pedal box is not adjustable, we recommend installing the slave cylinder only after the clutch is worn in after a few thousand miles. LOF does not recommend the installation: for newly installed clutches in combination with the LOF Power master cylinder
Prices incl. VAT;
Greasable track rod ends for all Land Rover Defender
Greasable track rod ends for all Land Rover Defender Greasable track rod ends for original track rod of Land Rover Defender 90/110/130. The set comprises three track rod ends, two with right-hand thread and one with left-hand thread, which can be greased with a grease gun. In contrast to the non-greasable OEM track rod ends, these suffer from much less wear and thus last much longer.
Prices incl. VAT;
Nakatanenga Spacers for Stabiliser Rear Axle, for Defender 110/130
Nakatanenga spacers for stabiliser rear axle for Defender 110/130 The spacers prevent the rear anti-roll bar from folding down when the vehicle is raised, for Land Rover Defender 110/130, suitable for all model years, incl. necessary mounting material. Dimensions per piece: 12x8x4 cm Scope of delivery: 2 spacers incl. fixing material
Prices incl. VAT;
Wheel nut TX1 for Land Rover Defender, galvanized, black passivated, individually and as a set
Wheel nut TX1 for Land Rover Defender, single or in set of 5 The TX-1 by the Ozzies at Performance Wheels, formerly also known as Outback TX-1, is a rally-tested alloy rim in a classic no-fuss design. The six solid spokes immediately emphasize what the TX-1 is all about and what off-roaders and overlanders want to have above all: performance. The rims are highly robust, easy to clean and therefore extremely durable. And that leads us to the next point: unfortunately, the TX-1 has been discontinued quite a while ago but if you’ve still mounted a set on your Defender, you’re most likely to hold on tight to your reliable mates from Down Under. Since the original wheel nuts were not as tough as the rims themselves though, we are now offering high-quality replacements, single or in sets of 5. The wheel nuts are made from performance steel and are surface treated by an expert shop with double Zintek 300B and Zintek Top and then passivated with Techseal Black SL2.
Prices incl. VAT;
Dotz hub cap
Reliable protection for the wheel hub For Land Rover Defender wheel DO716 Material: Chrome-plated stainless steel, Price per piece
Prices incl. VAT;
Manifold bolt M8 reinforced for Land Rover Td5
Durable mounting for your Td5 Manifold bolt M8, reinforced for Land Rover Td5. High strength bolts specially manufactured to our requirements. The use of special materials prevents the bolts from breaking off and the manifold from warping. This conversion measure is particularly recommended for chip-tuned TD 5 engines.Set with:10 x manifold bolts reinforced10 x nuts10 x lock nuts20x washers Application:First, insert a manifold bolt into the cylinder head.To tighten the manifold, keep the following order:1. put on two washers2. tighten the copper nut with a torque of 25 Nm3. finally screw the stainless steel nut hand-tight onto the copper nut.
Prices incl. VAT;
ServiceKit Land Rover Defender 300Tdi
ServiceKit Land Rover Defender 300Tdi Set contains branded filters in original equipment quality.For comparison, we have added the matching Land Rover part numbers.1x Air filter (ESR2623)1x Oil filter (ERR3340)1x Fuel filter (diesel) (AEU2147L)1x Oil pan gasket (UAM2847L)
Prices incl. VAT;
Gasket set intake manifold Defender TD4 2,4
New intake manifold gasket for Defender TD4 2.4 High-quality replacement gasket suitable for the intake manifold of the Land Rover Defender TD4 with 2.4 litre engine. For optimum sealing and reliable engine performance - ideal for maintenance or repair.
Prices incl. VAT;
König T2 220 / Thule XB-16 size 220 snow chain
Snow chains König T2 220 / Thule XB-16 for 4x4 and SUV, size 220 Product features 16 mm chain link thickness Manual tensioning system: one stop to attach and one stop to tension the chain Closed shortening hooks prevent the chain from twisting Suitable for the following wheel/tyre combinations: 6.7-14, 195/75R-14, 195/80R-14, 185/80R-15, 195/70R-15, 205/65R-15, 175/75R-16, 175/80R-16, 195/65R-16 The Thule snow chain range no longer belongs to the Thule Group but to the König company. The chain models that were previously sold under the Thule brand are now offered under the König brand. You will therefore receive snow chains from either Thule or König.
Prices incl. VAT;
2 Litre Castrol Differential Oil for Discovery 3 & 4
High quality Castrol axle oil - For Discovery 3 & 4 differentials This fully synthetic axle drive oil with LS (limited slip) additives is designed for use in highly loaded axle drives and multi-plate limited slip differentials. 2 litres Suitable for Discovery 3 & 4. Advantages: long oil change intervals thanks to excellent shear stability best wear protection at highest load profiles excellent cold flow behaviour reduced gear noise due to minimised vibrations Storage: oil should be stored under cover if possible. in the case of unprotected storage outdoors without a roof, the oil should be stored horizontally to prevent water penetration and to maintain the legibility of the labelling. do not store at temperatures above 60 °C avoid direct sunlight or frost
Content: 2 liters (€25.00 / 1 liters)
Prices incl. VAT;
Lockable fuel filler cap for Land Rover New Defender, including 2 keys
Lockable tank cap When fuel prices are high, opportunistic fuel thefts skyrocket and this affects us both at home and when traveling abroad. Furthermore - especially in our cities - SUVs and 4x4s are preferred targets for sabotage and vandalism by supposed climate activists and other thugs. Under these circumstances, it is hard to understand why high-priced cars such as the New Defender (from MY2020) do not come with lockable fuel filler caps. If you want to prevent thieves and saboteurs from gaining easy access to your fuel tank, we offer a lockable replacement cap with two keys. In addition to the New Defender, this lockable fuel cap fits the following models: Discovery 3 MY2004-2009Discovery 4 MY2009-2016Discovery5 from MY2014Discovery Sport Typ LC ab BJ2015 Range Rover (not Vogue) from MY2007Range Rover Evoque L538 MY2011-2018Range Rover Hybrid L405 from MY2013Ranger Rover Sport from MY2007Range Rover Velar from MY2017 Defender from MY2020 Jaguar E-Pace X540 from MY2017Jaguar F-Pace X761 from MY2016Jaguar F-Type (not USA) X152 from MY2013Jaguar XE from MY2015Jaguar XF from MY2007Jaguar XJ X351 MY2010-2019Jaguar XK Cabrio from MY2006Jaguar XK Coupe from MY2006
Prices incl. VAT;
Drive Shaft Spacer
Drive Shaft Spacer Compensates for height adjustment.Ships including hardware.
Prices incl. VAT;
Bracket injection nozzle Defender TD4 2.2 and 2.4
Mounting bracket suitable for injectors - Defender TD4 2.2 / 2.4 from MY2007 onwards suitable screws for mounting can be found here in the store
Prices incl. VAT;
Bumper protection for New Defender from MY2020, 3 colours
Bumper protection What’s worse than a scratch on your car? Clearly that very first scratch! How annoying is it when you spot one on a pristine new vehicle? Even when 4x4s generally wear their scars with pride, most signs of heavy usage aren’t necessary, they’re frustrating and also depreciate the value of your vehicle. One of the first areas to show signs of wear and tear – especially with off-road vehicles – is usually the cargo area. But if your 4x4 is a New Defender, would you really want to see a worn and scratched rear bumper? Immediate and long-lasting prevention of wear marks on your New Defender’s rear bumper can be achieved with our designated paint protection film. This high-performance product by industry leader 3M protects your New Defender’s rear bumper from scratches and abrasion even when your loading area is constantly in use for work or sports. And don’t forget the damage a dog’s claws can do to the paint when you carry them regularly in a dog box in the back. Due to its multi-layer structure, the 3M wrap also protects the bumper from chipping caused by the impact of small stones or dropped objects. Installing the paint protection film is really easy. Everything you need is included: cleaning cloth, adhesion promoter wipe, squeegee and detailed instructions. If you’ve never done this before: don’t worry. The protective wrap can be positioned exactly as you need it, but if you have to readjust the position a few millimeters that’s no problem either. Simply slide the film into place. It only starts to adhere once you apply pressure with the squeegee. The protective wrap is available in black, matt black, anthracite grey or silver, making it a perfect visual match for any New Defender color scheme. Comes in one complete „no worries“ kit: foil, squeegee, cleaner, primer. Please note: The transparent version differs from the other versions in terms of price and workmanship, as it uses a specially developed, UV-stabilised film. This film is specifically designed to minimise material yellowing caused by UV radiation and ensure long-term visual stability. The transparent film MUST be applied wet! For professional application, we provide detailed installation instructions and the necessary processing materials. Instructions for wet application: Fill a spray bottle with water and 1–2 drops of washing-up liquid (or mounting/application solution). Remove coarse dirt from the loading sill with a damp cloth and then clean thoroughly with the enclosed cleaning cloth – the surface must be clean and dust-free. Spray the loading sill evenly. Remove the protective film from the film and also spray the adhesive side lightly (so that it does not stick immediately). Apply the film and align it carefully. The moisture allows it to be moved around. Squeegee out the water, working from the centre outwards. Apply even pressure to remove the water and air bubbles. Remove any excess liquid with a cloth. The film is fixed after squeegeeing, but only reaches its final adhesion after 24–48 hours. During this time: Do not wash, do not use a high-pressure cleaner. Keep as dry as possible and avoid mechanical stress.
Prices incl. VAT;
Mounting kit for centre and rear silencer Land Rover Defender TD5 90/110
Mounting kit for centre and rear silencer Land Rover Defender TD5 90/110 The mounting kit allows easy mounting of the middle and rear silencer for the Land Rover Defender TD5.The kit includes 2 gaskets, 2 washers, 3 rubbers, 2 washers, 1 bolt, 1 nut.
Prices incl. VAT;
Starter Overhaul Kit for Land Rover Defender / Discovery Td5
Set for overhauling the starter motor of the Defender Discovery Td5 In 99 per cent of all the cases that a Td5 starter is replaced it is not the actual motor itself, but the magnetic switch that is broken. Often its contacts are burned or worn, which still allows the starter to spin, but without the engine starting or only starting very reluctantly. For these cases we offer a cost-effective solution: with our service kit you can overhaul your starter yourself for a fraction of the price for a new OE starter (more than EUR 400,-). This is an easy DIY job without the need for special tools or expertise. Note: our starter service kit is not available at the manufacturers DENSO or Land Rover! In contrast to many cheap offers, ONLY WE offer a complete kit with all necessery parts as well as enlarged and strengthened contact plates.
Prices incl. VAT;
Mounting material for 1 piece Koni / RAID shock absorber top and bottom
Mounting material for 1 piece KONI/ TREKFINDER Heavy Track RAID damper 90-5374SP1 + 90-5470, top and bottom Mounting material for the pin mounting of the shock absorber on both sides Suitable for all LAND ROVER Defender models Scope of delivery: 8 pieces metal washer + 4 pieces rubber + 2 pieces nut self-locking
Prices incl. VAT;
Wheel nut cover, black, for Land Rover Defender, 25 pieces
Wheel nut cover for Land Rover Defender Wheel nut cover, black, for Land Rover Defender, 25 pieces, SW27, made of high quality plastic.
Prices incl. VAT;
License plate holder for NAWIBU winch bumper
License plate holder for NAWIBU winch bumper Our heavy duty Nakatanenga winching bumper for classic Defenders is the perfect mounting solution for winches. The entire winching unit stays well protected behind the bumper and the winching cable runs smoothly through the integrated winch window in the middle of the bumper. Normally, this is where the license plate is positioned and that brings us to the problem and our simultaneously elegant and quick solution. Our custom made number plate holder is simply screwed into the fastening holes of the winching window, making it possible to mount the number plate more or less in its usual position. The winch’s functionality is in no way restricted or impeded, of course. The number plate holder is made from aluminum and features a matte black powder coating (RAL9005) which perfectly matches the look of the winching bumper. Material: AluminumFinish: RAL9005 matte smooth
Prices incl. VAT;
Shift Linkage Repair Kit Transfer Case for Land Rover Defender
Repair kit shift linkage / transfer case The transfer box on a Defender not only transmits the power from the engine two both axles, it also houses the middle diff lock as well as the reduction gearbox. The linkage connecting the transfer box to the low ratio/diff lock stick is naturally prone to heavy wear and tear. The repair kits give you the option to completely replace all worn bushes, bolts and the hexagon screw in the linkage. Nut, washers and SL retaining clips for the bolts are all included. Please note: Repair kit (REPSET-VEGE-LA) is compatible up to chassis-nr. LA999999 (ca. MY1994) Repair kit (REPSET-VEGE-MA) is compatible from chassis-nr. MA000000 (ca. MY1995)
Prices incl. VAT;
Continental Flat-blade Windscreen Wiper for Land Rover Defender, Set
Clear Vision in Any Weather: Continental Flat Blade Wipers for Your Defender! You know the drill: rain, snow, or spray – and your old windshield wipers smear more than they wipe? Especially in a Defender, where good visibility over rough terrain is crucial, you shouldn't make any compromises. Upgrade now to modern Continental flat blade wipers and experience the difference! This set is a perfect fit for your Land Rover Defender and brings the technology of modern vehicles directly to your windshield. Here's what the Continental Flat Blade Wipers offer you: Superior Wiping Performance: Thanks to the aerodynamic design and even pressure distribution, flat blade wipers provide a significantly cleaner and streak-free wiping result – even at higher speeds. Longer Durability: Flat blade wipers are often more resistant to weather influences and wear than conventional bracket wipers. Modern Look: Give your Defender a subtle yet modern touch. Less Wind Noise: The flat design can reduce wind noise compared to bulky standard wipers. Easy Installation: Changing them is child's play and done quickly. Old wipers off, new Continental wipers on – done! Complete set: The set consists of either two or three identical wipers for the windscreen and rear window of your Land Rover Defender 90/110/130. No more poor visibility and annoying juddering! Treat yourself and your Defender to an upgrade that you'll immediately appreciate on your next rainy drive. Ensure clear vision and safety! Order your set of Continental Flat Blade Wipers now!
Prices incl. VAT;
Oil seal crankshaft rear Defender TD4 2.4 and 2.2, for Defender from MY 2007 onwards
Oil seal crankshaft rear Fits DEFENDER 2007 and later.
Prices incl. VAT;
Clutch spring for Land Rover Defender
Finally, Easier Clutch Operation: The Nakatanenga Clutch Spring for Your Defender! It's easy to forget these days, but driving used to be real work, and you don't even have to go back as far as double-clutching or hand-cranking the engine to start. Over the decades, many things in the Defender have become more user-friendly: power steering and electric windows take the strain off your arms, but especially with the TD5 and older models, it's often still the case that your clutch leg needs to be significantly stronger than your accelerator foot. Particularly in the low-range gears off-road, when maneuvering with a trailer, or even in stop-and-go city traffic, the physical effort of pressing the clutch pedal quickly becomes noticeable. As an ergonomic and cost-effective solution to this annoying problem, we now offer a new torsion spring that reduces the effort required for clutching by up to 45% compared to original return springs. The new spring can be installed in 300Tdi, Td5, and Td4 models. The necessary bushings are supplied. The conversion at the clutch pedal also works on models older than those mentioned above if retrofitting with a newer pedal box is possible. We are, of course, happy to help with any questions regarding this. These are your advantages at a glance: Noticeably Lighter Clutch Operation: Reduces the required pedal force and makes clutching significantly more pleasant – a difference you'll notice immediately! More Driving Comfort: Relieve strain on your left leg, especially in stop-and-go traffic, off-road, or on extended journeys. Easy Installation: The spring is designed so that it can be relatively easily exchanged for the original spring. Perfect Fit for Your Defender: Developed for Land Rover Defender models (please note compatibility with your exact model year and type, especially for 300 Tdi, Td5, Td4 2.4 & 2.2). Small Change, Big Impact: An often-underestimated modification that can significantly improve everyday driving with your Defender. Many Defender drivers swear by this simple yet effective optimization. If you desire more comfort when clutching without changing the fundamental characteristics of your vehicle, this spring is the ideal solution. Give your left foot a break! Order the Nakatanenga Clutch Spring now and experience a new level of shifting comfort in your Defender! If you're looking for a technically more sophisticated solution with even greater force reduction, you should take a look at our POWERmaster master cylinder for the clutch hydraulics here. You can find bearings and bushings as spare parts here.
Prices incl. VAT;
Replacement gasket set 4pcs for Ashcroft intermediate shaft MT82
Spare gasket set 4 pcs. for Aschcroft MT82 intermediate shaft 2 pieces precision O-ring 43,82 x 5,33mm2 pieces precision O-ring 75 x 2mm
Prices incl. VAT;
Wheel Bearing Nut 52mm for Land Rover Defender
Wheel bearing nut 52 mm for Land Rover Defender
Prices incl. VAT;
Performance LED light bulb, RW501DLED
Ring LED bulbs type RW501DLED These bulbs have a long life and are more resistant than conventional bulbs.Compared to halogen lamps, these LED lamps have a much lower power consumption. Technical details: 12V7000K (white)3D technology Advantages: vibration-proof durable more resistant was developed to replace a conventional car lamp Delivered is a set consisting of 2 lamps. IMPORTANT NOTE:Not approved for the STVO!
Prices incl. VAT;
Spare wheel cover, vinyl, for tyres up to 235/85R16
Spare wheel cover made of vinyl, for tyres up to 235/85R16, corresponds to DA2027
Prices incl. VAT;
Screw set for flywheel LR116372
Bolt set for flywheel LR116372 This high-quality bolt set for flywheel LR116372 contains all the fastening bolts required for professional and secure installation. Lieferumfang Set: 8 Stück Schrauben
Prices incl. VAT;
Emergency valve extra short - Colby Valve
FOR AN EMERGENCY IN THE TERRAIN! It is quite annoying and very time-consuming when a tire valve is broken in the middle of the terrain.If it does happen, then we have the solution here: The extremely stable emergency valve from Colby Valve! The exchange is quick and uncomplicated. You only need a few minutes because disassembly of the tire is not necessary. The valve can be plugged into the valve opening from outside even in tight spaces. The Ultimate System is far smaller than the "Emergency System". The installation succeeds only with tools. Basic information: 2 pack Installation from the outside 20x more stable than conventional valves very good quality Color: Black ATTENTION!Only for off-road use! Valve is not allowed in the area of StVo (German traffic regulations)
Prices incl. VAT;
Emergency valve - Colby Valve Emergency
FOR AN EMERGENCY IN THE TERRAIN! It is quite annoying and very time-consuming when a tire valve is broken in the middle of the terrain.If it does happen, then we have the solution here:The extremely stable emergency valve from Colby Valve! This is inserted from the outside into the valve opening and fixed by a thumbscrew. The exchange is fast, uncomplicated and above all WITHOUT tools! You only need a few minutes because disassembly of the tire is not necessary. Basic information: 2 pack Installation from the outside no tools needed 20x more stable than conventional valves very good quality Should the wing nut disturb, then there is alternatively still the "Colby Valve Ultimate". This valve is much smaller, but can only be mounted with a tool. ATTENTION!Only for off-road use! Valve is not allowed in the area of StVo (German traffic regulations)
Prices incl. VAT;
Spacer for viscous fan for Land Rover Defender Td4
Effective cooling optimisation for Land Rover Defender TD4 2.4 - 25 mm spacer for viscous fan Spacer / distance piece for Land Rover Defender Td4 2.4 increases cooling output of viscous fan and thus prevents overheating in hot environments at slow speeds, heavy terrain or when pulling heavy trailers. Fitting of the 25 mm spacer is easy.
Prices incl. VAT;