ROADspec TDCI Puma Including adapter and valve adapter Clutch slave cylinder The ROADspec clutch is specifically designed for your daily road-going Defender with 2.4l or 2.2l Puma engine. If you do a bit of towing now and then, perhaps some light off-roading or just use your Landy as a commuter, then the ROADspec has everything you need to keep you going for years to come. It’ll even take mildly tuned motors that have a little more poke than standard! And by the way, the pedal weight is not heavier than the original. This kit includes the release bearing and concentric slave cylinder unit Description:  LOF HD friction material High torque sprung center hub G90 high-temp assembly grease Updated 2.2l genuine release bearing/slave cylinder Pedal weight not heavier than original If you have a 2.4l engine and have not changed to the updated release bearing and slave cylinder then you will need this bleed valve and adapter. SET consists of: ROADspec coupling TD4 Adapter Valve adapter for clutch cylinder You can find more products for improved clutch performance here: clutch spring Note from LOF: if this clutch is newly installed, the LOF Powermaster clutch master cylinder should not be installed as well. We recommend replacing the pilot bearing when replacing the coupling. Please note:  Before installing the clutch, the dimension of the following step must be measured on the flywheel If the dimension is 25.4 mm, the clutch can be installed. If the measurement is 22.2 mm, a Ford flywheel is installed. The clutch is not compatible with this and will malfunction sooner or later. If a Ford flywheel with a measurement of 22.2 mm is installed, you will also need the following Land Rover flywheel.

POWERspec Clutch TD4 Including adapter and valve adapter Clutch slave cylinder At LOF clutches, POWERspec is the next step up from ROADspec when it comes to performance. If you tow regularly or carry extra weight like expedition trucks do then this is the spec for you. It’ll handle highly tuned road monsters or hard worked off-roaders all day long. If you want reliability and drivability from your mapped motor POWERspec will keep you moving forward!  This kit features heavy duty friction material, a high torque sprung center hub as well as the updated OEM release bearing and the slave cylinder for the 2.2l engine. And by the way, the pedal weight is not heavier than the original. This is your best option for all Tdci Defenders with remapped engines, it is ideal for your daily drive, for towing and overlanding!  Description: LOF HD friction material High torque sprung center hub G90 high-temp assembly grease Updated 2.2 genuine release bearing/slave cylinder Pedal weight no heavier than original If you have a 2.4l engine and have not changed to the updated release bearing/slave cylinder then you will need the bleed valve and adapter. SET consists of: POWERspec coupling TD4 Adapter Valve adapter for clutch slave cylinder You can find more products for improved clutch performance here: clutch spring Note from LOF: if this clutch is newly installed, the LOF Powermaster clutch master cylinder should not be installed as well. We recommend replacing the pilot bearing when replacing the coupling. Please note: Before installing the clutch, the dimension of the following step must be measured on the flywheelIf the dimension is 25.4 mm, the clutch can be installed.If the measurement is 22.2 mm, a Ford flywheel is installed. The clutch is not compatible with this and will malfunction sooner or later.If a Ford flywheel with a measurement of 22.2 mm is installed, you will also need the following Land Rover flywheel.  

saving bundle: Heavy Duty clutch kit incl. Improved MT82 intermediate shaft for TD4 saving bundle consisting of automatic clutch, friction disc, release bearing, matching clutch slave cylinder and a reinforced intermediate shaft MT82 transmission. For TD4 built in 2007-2016 Information about the clutch automat with friction disc, release bearing and clutch slave cylinderEspecially with switching operations under higher load, such in trailer operation or in performance-enhanced vehicles, enormous forces must be transmitted by the clutch. A common problem with the Defender's original clutch is the failure of the insufficiently sized torsion springs. The torsion springs, specially adapted to the Defender Td4, eliminate the familiar problems of clattering or jamming clutches. Another, but less common, problem is the ingress of oil from the engine or transmission into the clutch bell. This oil is absorbed by the porous friction linings and occurs during driving by the resulting frictional heat repeatedly to the friction lining. Due to the reduced traction it comes in the episode to a higher heat development and vitrification of the coverings. The heat is a measure of the converted energy that is no longer available to the drive! The organic coating used in this coupling can not absorb oil and therefore does not vitrify. It convinces with specially adapted friction modifiers with a soft response and enables a 100% adhesion. Of course, the pads are asbestos- and lead-free, free of other toxic heavy metals and heavy metal compounds. Information on the reinforced intermediate shaft for MT82 transmissions.Improved intermediate shaft for MT82 transmission in Land Rover Defender TD4 / TDCi / Puma 2.4 / 2.2 Known problem: The intermediate shaft of the TD4 / TDCi / Puma 2.4 / 2.2 models is not greased and is not supplied with oil. The connection of the two-piece intermediate shaft wears after prolonged use, since the shaft with outer ring gear has direct contact with the shaft with inner ring gear. In the worst case, this wear ensures that the sprocket shears off and the vehicle thus stops. A regular lubrication of the sprocket helps, but is in the long run very cumbersome Our solution: The improved intermediate shaft is supplied with the oil of the gearbox and thus prevents the wear of the shafts. Easy and uncomplicated! We recommend replacing the pilot bearing when replacing the coupling. Please note:  Before installing the clutch, the dimension of the following step must be measured on the flywheelIf the dimension is 25.4 mm, the clutch can be installed.If the measurement is 22.2 mm, a Ford flywheel is installed. The clutch is not compatible with this and will malfunction sooner or later.If a Ford flywheel with a measurement of 22.2 mm is installed, you will also need the following Land Rover flywheel.

Clutch slave cylinder for Defender TD4 You can choose between a clutch slave cylinder for Defender TD4 up to chassis number 8A999999 and a clutch slave cylinder for Defender TD4 from chassis number 9A000001.ATTENTION: Occasionally, different clutch release bearings may have been fitted by previous owners. If you are not sure which clutch slave cylinder you need for your release bearing, please order the other clutch slave cylinder. You can then test both and return the non-fitting part to us within 4 weeks in its original packaging.

For more stability and smooth running Improved intermediate shaft for the MT82 gearbox in the Land Rover Defender TD4 / TDCi / Puma 2.4 / 2.2 Known problem: The intermediate shaft on the TD4 / TDCi / Puma 2.4 / 2.2 models is not greased and is not supplied with oil. The connection of the two-part intermediate shaft wears out after prolonged use, since the shaft with the outer gear rim is in direct contact with the shaft with the inner gear rim. In the worst case, this wear causes the ring gear to shear off and the vehicle to stop. Regular greasing of the ring gear helps, but is very cumbersome in the long run. Our solution: The improved intermediate shaft supplies itself with the oil of the gearbox and thus prevents the shafts from wearing out. Easy and uncomplicated!