CargoBear 2.0 roof rack system for Land Rover Defender

Seat cover for Land Rover New Defender 110/130, driver and passenger side This isn’t off-the-peg, this is made to measure! If you’re looking for seat covers for the New Defender – the front seats to be precise – look no further than our seat protectors made from durable, and easy-to-clean 1000D Nylon 6.6. The seat covers were developed by us in our own tailor's workshop  – guaranteeing highest functionality and best workmanship. To ensure maximum comfort and compatibility with the climate technologies in your seats, the covers feature breathable mesh fabric on the actual sitting surface. And even though it is mesh, it will still protect the seat from dirt and moisture. To achieve a perfect fit, the one-piece cover is tightly tailored and does not require zippers or similar. Simply pull it over the seat, Velcro the top part underneath the headrest and close the sturdy straps and buckles on the underside. Additionally, a mesh pocket with a rubber foam piece inside is wedged into the gap between backrest and seat surface to prevent the cover from sliding. On the sides, openings in the cover allow easy access to the headrest controls. As with all our textile products, we always aim to add additional storage space. Generously sized MOLLE patches on the sides as well as large pockets in the rear of the backrest and the front rail of the seat make it very easy to store everyday items and small pieces of equipment temporarily or permanently. Our seat protectors come in the colors Coyote or black with uni-colored mesh insets. Material: Nylon, PU-coated Not suitable for New Defender 90The seat in the 90 design has a folding mechanism on the side to tilt the seat. These seat covers have NO! Recess for this lever.  This article was designed in our in-house tailor shop. A dedicated team and short distances allow for continuous quality control and further development of our textile products. And if you already have a tailor's workshop in house, then it is easy to also accept customer change requests, special designs, suggestions and proposals for improvement at short notice and to implement them as far as possible. Mail or phone call is all it takes! And by the way: At Nakatanenga we only use materials with 100% nylon PU coating for all textile articles. Unlike PVC, nylon PU (polyurethane) is free of harmful phthalate-based plasticisers. Until recently, low-molecular phthalates were the most common plasticisers for plastics of all kinds and are even used in food and cosmetics. However, they accumulate in the environment and are suspected of acting like endogenous hormones due to their molecular nature. This is highly questionable from a toxicological point of view and is considered to be a trigger for various diseases, including cancer. For Nakatanenga, it is therefore a matter of course to use only ecologically and health-safe alternatives such as nylon PU for the coating of textile products.

Nakatanenga CargoBear Mounting brackets for Awnings The CargoBear awning holder allows you to mount numerous awnings on the CargoBear roof rack for Defender and on the CargoBear roof rack for Mercedes G. It is suitable for the following awning models, among others: RoofLodge Awnings RhinoRack Foxwing RhinoRack SunSeeker At least two CargoBear cross bars are required for assembly. The 4-piece set is supplied including the necessary assembly material for attaching the awning holder to the CargoBear roof rack. Fixing material for the awning is not included. The awning holder is made of stainless steel. It can be used on all CargoBear carriers with 30° feet (e.g. Land Rover Defender or Mercedes G). Material: black powder-coated stainless steel Suitable for all CargoBear 1.0 + 2.0 roof racks!

Nakatanenga CargoBear end plate Defender Beautiful and handy, this CargoBear end plate for the Defender. Beautiful because it adds the finishing touch to the design of the already extremely attractive black bear. Particularly on the short Landy, with the roof rack configuration of three crossbars and two perforated board surfaces, the wind deflector and end panel round off the look perfectly on both sides and, above all, provide the ideal roof rack length for the vehicle. And then, as already mentioned, the end panel is also very handy because we have integrated a handle on both sides, which makes climbing up to the roof level much easier and safer. The end module also extends the usable loading area by another 9 cm and offers additional space for attaching work LEDs, fastenings, lashing points and the like. Above all, however, it can protect the rear edge of the roof when loading and unloading the bear - depending on the CargoBear configuration and vehicle. As always in our modular CargoBear system, the material is a black, powder-coated aluminum-magnesium alloy with a non-slip perforated plate structure. The end plate is supplied with all the necessary fastening material. Material: Aluminum-magnesium alloy (AlMg3), high-quality powder-coated Color: Deep black RAL 9005 Width: 1,450 mm Suitable for all CargoBear 1 + 2 roof racks.    

More grip, less risk - rubber cover profiles for the Nakatanenga CargoBear How do you improve the CargoBear? By clicking our rubber covers into fully or partially unused lashing openings in the rack. With our 30 mm wide and 10 cm long strips, you can quickly and securely seal the gaps. The rubber covers give you a whole range of noticeable advantages. Firstly, they improve load safety on the already very slip resistant CargoBear even further. When you position the cargo on top of the rubber strips, the ribbed surface structure prevents the lashed down cargo from sliding. A second effect is created by the rubbers’ added height of 3.5 mm, which lifts the cargo off the actual rack, preventing scratching or damages to both. And last but not least, the covers also prevent vegetation from getting trapped or stuck in the sideways rails when off-roading. The covers sport rounded edges for a better fit. The rubber cover strips for the CargoBear can be ordered in sets of 6 or 24 respectively. One crossbar requires a set of 6 for Defender, Jimny or G-Class. A set of 24 covers one cargo panel with the above-mentioned 4x4s, i.e. the minimum configuration of 2 cross bars and one panel requires 2 sets of 6 and one set of 24. If you have any questions, don’t hesitate to get in touch.

The perfect addition: cover profile for your airline rail Available in: 1 m or 10 cm steps (free choice of length) - max. 25m in one piece Please note:Since there are so many different possible uses and we do not know your requirements, we need the information from you about the length and denomination of the profiles you need. Please enter this in the free field at the end of the ordering process. One thing is certain: airline lashing rails would have to be invented if they didn’t exist already. Few systems for securing cargo are simultaneously as flexible, robust and safe. If you ever had to tie down large, unwieldy or sensitive objects in your cargo hold or on the roof rack, you’ll know what we mean. So how do you actually improve lashing rails? By clicking rubber covers by Trekfinder into unused tracks. A simple, fast and secure solution. The rubber strips add little height with 3.5 mm and prevent dirt and dust from clogging fully or partially unused rails. This is particularly important in cargo holds or on open trailers, because dirt clogged rails make it harder to attach fittings and studs. The same goes for winter weather when snow and ice can render exposed rails next to useless. The rubber strips feature a ribbed surface to improve load safety. Loads that are positioned on top of the rubbers won’t slip or slide as easily. On roof racks, wind noises are being reduced and if you have mounted airline rails sideways on the rack or the vehicle itself, the rubbers prevent vegetation from getting trapped when off-roading. That’s a lot of bang for your buck. The rubber covers can be ordered in widths of 23 mm or 30 mm

The new Defender combines modern technology with proven off-road capability. Good air circulation as if the windows were slightly open, but without the risk of rainwater or theft? Plus effective protection against insects? That's what our ventilation panels with mosquito nets offer, made to fit the New Defender perfectly from high-quality aluminum—no wobbly universal parts. Supplied in pairs and powder-coated in black, they complement the modern design discreetly and sensibly, especially when camping or on expeditions. Installation is straightforward: roll down the window, insert the ventilation panel, close the window again – and it sits securely and rattle-free. ⚠️ Important note: Children and animals must never be left in the vehicle at high temperatures, even with the ventilation panels in place. Suitable for Defenders built from 2020 onwards. Length: 550 mm  

Wind deflector - suitable for Nakatanenga CargoBear 1.0 and CargoBear 2.0 Land Rover Defender - for sloping element Material: Aluminium, black matt powder-coated RAL 9005 incl. fixing material the wind deflector extends the CargoBear by 10 cm. lightbars or headlights can be mounted on the wind deflector. suitable for all CargoBear 1 + 2 roof racks! Please note: When using a snorkel, the wind deflector may need to be adjusted.  

Nakatanenga CargoBear - Crossbar angled / low Suitable for CargoBear angled wind deflector  Material:  Aluminum, black matt powder-coated RAL 9005 incl. fastening material Slanted/low crossbar is the matching bracket for slanted wind deflector suitable for all CargoBear 1 + 2 roof racks! can only be mounted at A-pillar height Suitable for mounting lamps and headlights

Fastening set for AluBoxes on Nakatanenga CargoBear 1.0 and 2.0 Probably the easiest and safest way to mount an AluBox on CargoBear 1 or 2: Our customised fastening solution consists of 4 brackets that screw the box base firmly to the roof rack from the inside. This not only serves to secure the box for transport, but also prevents it from being quickly stolen on the road when it is locked. Mounting the brackets is child's play. Apart from the tools, everything you need is included. You can download detailed instructions from our web shop, where you will of course also find a large selection of matching aluminium boxes.  

Single Stud Fitting For airline cargo lashing rails, load capacity 300 kg, ring diameter 40 mm, manufactured according to ISO 9788, anodised aluminium, UV and salt water resistant. This single stud also fits our Cargobear. Please note: Depending on availability, the Single Stud is delivered in blue or black.

Bracket for CB antenna / radio antenna for Nakatanenga CargoBear system roof rack This robust bracket was specially developed for mounting a CB or radio antenna on CargoBear system roof racks. It is made of high-quality stainless steel and is powder-coated in black for additional corrosion protection and an attractive appearance. Ideal for off-road enthusiasts, long-distance travellers or professional use - with this mount you can securely and stably attach your antenna to the vehicle.Product details:  Suitable for all CargoBear 1 and 2 roof rack systems  Made of rust-free stainless steel  Surface: black powder-coated  Resistant to weather and mechanical stress  Simple and secure attachment  Can be used universally for various CB or radio antenna models Scope of delivery:1x antenna holder (without antenna)Note:The delivery does not include the antenna. The indicated price refers to one piece.

Handle for Nakatanenga CargoBear roof rack system Do you already have a CargoBear roof rack? Then you have probably used the mounting rail as a handle. This is unpleasant and you can easily hurt yourself - as we know from personal experience.That's why we decided to offer a suitable handle for the Cargobear. They are very useful for little effort - the handle is easy and quick to install. So easy and so ingenious! Dimensions: Length: 300 mm Height: 66 mm Handle diameter: 28 mm Material: aluminum plastic coated RAL9005 Delivery: 1 pc handle 2 pcs slot nut mounting material -Suitable for all CargoBear 1 + 2 roof racks!

Wind deflector suitable for Nakatanenga  CargoBear 2.0 Land Rover Defender Material: aluminium, black matt powder-coated Incl. Mounting material Suitable for all CargoBear 1 + 2 roof racks! Please note: When using a snorkel, the wind deflector may need to be adjusted.