Nakatanenga CargoBear end plate Defender Beautiful and handy, this CargoBear end plate for the Defender. Beautiful because it adds the finishing touch to the design of the already extremely attractive black bear. Particularly on the short Landy, with the roof rack configuration of three crossbars and two perforated board surfaces, the wind deflector and end panel round off the look perfectly on both sides and, above all, provide the ideal roof rack length for the vehicle. And then, as already mentioned, the end panel is also very handy because we have integrated a handle on both sides, which makes climbing up to the roof level much easier and safer. The end module also extends the usable loading area by another 9 cm and offers additional space for attaching work LEDs, fastenings, lashing points and the like. Above all, however, it can protect the rear edge of the roof when loading and unloading the bear - depending on the CargoBear configuration and vehicle. As always in our modular CargoBear system, the material is a black, powder-coated aluminum-magnesium alloy with a non-slip perforated plate structure. The end plate is supplied with all the necessary fastening material. Material: Aluminum-magnesium alloy (AlMg3), high-quality powder-coated Color: Deep black RAL 9005 Width: 1,450 mm Suitable for all CargoBear 1 + 2 roof racks.    

Albrecht CB radio VOX microphones offer the perfect solution for hands-free communication in vehicles in accordance with Section 23 (1a) of the Road Traffic Act, which prohibits the use of microphones by hand in vehicles from July 1st, 2020. These microphones can be used with almost all CB radios on the market. The integrated active noise cancellation function filters out disruptive background noise and offers very clear voice transmission. The integrated battery has an operating time of approx. 60 hours and can also be charged while the microphone is in use. Properties:► for hands-free communication in the vehicle (compliant with § 23 (1a) StVO, which prohibits the use of microphones by hand in vehicles from July 1st, 2020)► Active Noise Cancellation filters out disturbing background noise► VOX sensitivity adjustable in 4 levels► VOX delay adjustable in 4 levels► Impedance: 4.7K ohms► Sensitivity: -58db► Up / Down buttons► integrated battery 3,000 mAh (rechargeable)► Operating time: approx. 60 hours► Can be used while charging► Micro-USB charging socket on the microphone► Connection: 6-pin CB radio plug

The Albrecht CB-radio VOX microphone offers the perfect solution for hands-free communication in any vehicle, following § 23 (1a) of the German road traffic regulations. This paragraph outlaws the usage of handheld microphones since the 01.07.2020. This microphone can be used with almost all CB-radios on the market to date. It comes with active noise canceling to filter out any background noise, to guarantee clear communication. The battery lasts about 60h and can charge while in use Details: hands-free communication, following § 23 (1a) of the German road traffic regulations. This paragraph outlaws the usage of handheld microphones since the 01.07.2020 active noise canceling, eliminating irritating background noises VOX sensitivity adjustable in 4 levels VOX delay adjustable in 4 levels impedance: 4.7K ohm sensitivity: -58db 3000mAh battery (rechargable) 60h battery life micro-USB charging port Up/Down button plug: 4-point connector Scope of delivery:VOX microphone, instructions, USB charging cable Compatible with:Midland M10, Midland M Zero Plus, Alan 100 Plus B, diverse Präsident Geräte, Lavayette, etc.

The CB-radio VOX microphone offers the perfect solution for hands-free communication in any vehicle, following § 23 (1a) of the German road traffic regulations. This paragraph outlaws the usage of handheld microphones since the 01.07.2020. This microphone can be used with almost all CB-radios on the market to date. It comes with active noise canceling to filter out any background noise, to guarantee clear communication. The battery lasts about 60h and can charge while in use. Details: hands-free communication, following § 23 (1a) of the German road traffic regulations. This paragraph outlaws the usage of handheld microphones since the 01.07.2020 active noise canceling, eliminating irritating background noises VOX sensitivity adjustable in 4 levels VOX delay adjustable in 4 levels impedance: 4.7K ohm sensitivity: -58db 3000mAh battery (rechargable) 60h battery life micro-USB charging port Up/Down button plug: 4-point connector Scope of delivery:VOX microphone, instructions, USB charging cable Compatible with:Midland M10, Midland M Zero Plus, Alan 100 Plus B, diverse Präsident Geräte, Lavayette, etc.

Brief description: DV antenna cable 5m RG58 with PL foot incl. Weather protection cap and FME PL adapter - solderless This article is perfect as a roof duct for an antenna cable to operate a CB radio system. The supplied cover cap protects the PL foot from the weather when an antenna is not in use. The detachable PL adapter makes it easy to lay the cable inside the vehicle or to carry it out in tight spaces. There is no longer any need for soldering work because this article is provided with a PL screw connection on both sides. This article is ideal if, for example, you want to use our Cargobear antenna holder on our Cargobear in the rear area and are looking for a clean solution for the cable duct in the interior right up to your CB radio.

Wind deflector suitable for Nakatanenga  CargoBear 2.0 Land Rover Defender Material: aluminium, black matt powder-coated Incl. Mounting material Suitable for all CargoBear 1 + 2 roof racks! Please note: When using a snorkel, the wind deflector may need to be adjusted.

Permanently good reception with the CB fixed mounting antenna The 1/4 lambda antenna is easy to mount and offers a wide bandwidth incl. DV connection. It consists of a stainless steel radiator with flux points and a wing nut. The standing wave ratio is preset and can be changed by changing the radiator length. Mounting instructions: Drill a hole with a diameter of 12 mm at a point on the vehicle body.Deburr the hole and ensure a good conductive connection of the antenna flux.Then insert the antenna base from the outside of the body into the hole so that the corrugated side of the antenna joint faces the outside of the vehicle. Fit the plastic washer and the metal trident washer the right way round. Fit the toothed washer and screw on the nut loosely After aligning the base, tighten the nut on the inside of the body with a spanner Screw on the angle plug with the antenna cable (tip: seal with silicone to permanently seal the mounting point against rust) Mount the radiator with the threaded bolt on the antenna base Technical data: Frequency: MHz 26-28 Type: 1/4 Lambda Power rating: 300 W Radiator length: 130 cm Steel material: Stainless steel SWR Adjustable - SWR adjustment via length change: SWR preset Special features: Plug type DV Total length with base: 138 cm The antenna has a cable with an open end to make it easier to lay the cable. For connection to a radio set you still need a PL259/6 plug for RG58 coaxial cable.

Perfect mounting on the vehicle - antenna holder for the bumper The Nakatanenga antenna holder allows easy mounting of an antenna on the OEM bumper of the Land Rover Defender 90/110/130, making it easy to attach a CB or amateur radio antenna. The holder is made of stainless steel.

High quality Nakatanenga crossbars for Land Rover Defender Who does not need an entire roof rack on his Land Rover Defender, because just want to mount a roof tent on two cross-beams, for which the Nakatanenga CargoBear crossbars are optimally suited! They are identical to the crossbars of the CargoBear roof rack and therefore combine all their advantages: made of a light and stable aluminum-magnesium alloy (AlMg3) high quality powder coated (RAL 9005 - deep black) width: 1.450 mm (of which 1.300 mm for the usable area) length: 120 mm completely made in Germany Furthermore, two or three brackets can be upgraded by buying the missing parts to a full CargoBear roof rack - this is just the advantage of the modular system carrier! Of course, numerous accessories for the CargoBear roof rack with the crossbars can be used. Please note: The CargoBear roof rack / crossbar can not be installed on defenders that have a ribbed roof (see photo). An approximate indication of the series is between 1983 and 1989. Installation note:M10 lens head: 20 Nm to 25 NmM6 lens cylinder head: 10 Nm to 12 Nm Measured from the gutter, the Cargobear is approx. 23 cm high. On the roof it is approx. 5-6 cm - depending on the roof, condition, year of construction etc.

The stainless steel mounting kit Is for mounting various brackets on the CargoBear system roof rack or on the Cargobear crossbar - e.g. the CargoBear quick mounting frame is attached with this mounting kit (the mounting kit is already included with the quick mounting frame). The kit consists of 4 stainless steel sliding blocks with matching M8 stainless steel screws. The long screw makes installation easier, as the sliding block can be easily positioned with it (see 2nd and 3rd picture). Dimensions of a sliding block: Length: 65 mm Width: 18.5 mm Height: 6 mm Material:  Stainless steel Please note: The CargoBear can generally be fitted to a vehicle with a lifting roof/camping roof, but a few things must be taken into account. Please contact us for more information. Suitable for all CargoBear 1 + 2 roof racks!      

Nakatanenga CargoBear 2.0 – The Lightweight and High-Performance Roof Rack Quick navigation: The standard combinations of the modules Available lengths (dimensions and weights) Mounting instructions and downloads When it comes to powerful performance, our very own CargoBear is definitely the Grizzly among roof racks. Strong, sturdy and massively versatile, it was way ahead of its time when we introduced it in 2016. But the world is turning, evolution doesn’t favor a standstill and if you want to survive in nature, you need to keep innovating. Leaner and meaner is this new bear, the CargoBear 2.0, when he emerges from his winter den in Berg. Same load bearing strength, same solidity, same rigidity, but greatly reduced fight weight: Your 4x4 has to carry around 30 % less weight on the roof. And on top of it, the new CargoBear comes with a reduced price tag as well. How did we do it? The crucial difference lies in a new construction design. Removing the comparatively heavy longitudinal connecting beams, their structural function has been taken over by newly developed perforated HIGRIP plates between the crossbars and angled end-plates for the sides. The new design achieves (nearly) the same structural strength as its predecessor but reduces the net weight considerably.  The CargoBear 2.0 has been designed for a load capacity of 300 kg off-road (with evenly distributed load). This can easily be doubled on the road. Theoretically, that is, because it’s important to make two points when it comes to roof racks. One, keep in mind that your vehicle’s centre of gravity can shift upwards considerably when carrying a roof rack with cargo, especially off-road. And two, when loading your roof rack, the limitations will most likely result from your vehicles approved roof load which in most cases will be significantly below the specifications of the rack itself. Some of the CargoBear 2.0’s features stay the same, however, because we found them hard to improve: this includes the jet-black, super-flat look, the high-performance material and the modular versatility. Furthermore, all accessories, additional components, roof tents etc. are fully compatible with the first generation.  And last but not least, the old heavier CargoBear with longitudinal beams and checker plate will be continued exclusively for classic Defenders who need specific heavy-duty applications.  PLEASE NOTE: In Defender with pop-up roof / lift roof, the original roof is often shortened. If necessary, the roof rack then does not fit. Please measure beforehand or contact us in advance if you have any questions. Please note:When using a snorkel, the wind deflector may need to be adjusted. Please note: The CargoBear can be used on an AluCab pop-up roof.  The standard combinations of modules:(Click to enlarge) Defender 90 1,890 mm - 2 Modules optional: end beam, wind deflector Defender 90 2,075 mm - 3 Modules optional: end beam, wind deflector Defender 90 2,075 mm - 3 Modules incl. inclined extension (front module) optional: end beam Defender 90 1,005 mm - 1 Moduls optional: end beam, wind deflector                 Defender 110 SW/HT 2,775 mm - 3 Modules optional: end beam, wind deflector  Defender 110 SW/HT 2,765 mm - 3 Modules incl. inclined extension (front module) optional: end beam Defender 110 SW/HT 1,890 mm - 2 Modules optional: end beam, wind deflector Defender 110 SW/HT 1,005 mm - 1 Moduls optional: end beam, wind deflector                 Defender 110 DC 1,545 mm - 2 Modules optional: end beam, wind deflector Defender 110 DC 1,545 mm - 2 Modules incl. inclined extension (front module) optional: end beam Defender 110 DC 1,005 mm - 1 Moduls optional: end beam, wind deflector                 Defender 130 1,545 mm - 2 Modules  optional: end beam, wind deflector  Defender 130 1,545 mm - 2 Modules incl. inclined extension (front module) optional: end beam Defender 130 1,005 mm - 1 Moduls optional: end beam, wind deflector                   Available lengths (dimensions and weights): Module:   Länge: Gewicht: 1 Modul: 1x L 1,005 mm   2 Module: 1x L + 1x K 1,545 mm - geeignet für 110 DC, 130 CC   2 Module: 2x L 1,890 mm - geeignet für 90 er   3 Module: 3x L 2,775 mm - geeignet für 110 SW/HT   3 Module mit schräger oder normaler Eweiterung: 1x L + 2x K 2,075 mm - optimal für 90er   3 Module mit schräger Eweiterung: 3x L 2,765 mm - optimal für 110er   Schräges Erweiterungsmodul:   875 mm Erweiterungsmodul lang:   885 mm   Erweiterungsmodul kurz:   540 mm     Installation note:M10 lens head: 20 Nm to 25 NmM6 lens cylinder head: 10 Nm to 12N m Measured from the gutter, the CargoBear is approx. 23 cm high. On the roof it is approx. 5-6 cm - depending on the roof, condition, year of construction etc. You can find ideal protection for the lashing rail profile on the CargoBear or for all other lashing rails here. If you need spare parts or extensions for the CargoBear 1.0, please ask us by email or phone. Further keywords for this item: cargo-bear, cargobear, CargoBear, roof-rack, roof rack