Brief description: DV antenna cable 5m RG58 with PL foot incl. Weather protection cap and FME PL adapter - solderless This article is perfect as a roof duct for an antenna cable to operate a CB radio system. The supplied cover cap protects the PL foot from the weather when an antenna is not in use. The detachable PL adapter makes it easy to lay the cable inside the vehicle or to carry it out in tight spaces. There is no longer any need for soldering work because this article is provided with a PL screw connection on both sides. This article is ideal if, for example, you want to use our Cargobear antenna holder on our Cargobear in the rear area and are looking for a clean solution for the cable duct in the interior right up to your CB radio.

Albrecht CB radio VOX microphones offer the perfect solution for hands-free communication in vehicles in accordance with Section 23 (1a) of the Road Traffic Act, which prohibits the use of microphones by hand in vehicles from July 1st, 2020. These microphones can be used with almost all CB radios on the market. The integrated active noise cancellation function filters out disruptive background noise and offers very clear voice transmission. The integrated battery has an operating time of approx. 60 hours and can also be charged while the microphone is in use. Properties:► for hands-free communication in the vehicle (compliant with § 23 (1a) StVO, which prohibits the use of microphones by hand in vehicles from July 1st, 2020)► Active Noise Cancellation filters out disturbing background noise► VOX sensitivity adjustable in 4 levels► VOX delay adjustable in 4 levels► Impedance: 4.7K ohms► Sensitivity: -58db► Up / Down buttons► integrated battery 3,000 mAh (rechargeable)► Operating time: approx. 60 hours► Can be used while charging► Micro-USB charging socket on the microphone► Connection: 6-pin CB radio plug

The Albrecht CB-radio VOX microphone offers the perfect solution for hands-free communication in any vehicle, following § 23 (1a) of the German road traffic regulations. This paragraph outlaws the usage of handheld microphones since the 01.07.2020. This microphone can be used with almost all CB-radios on the market to date. It comes with active noise canceling to filter out any background noise, to guarantee clear communication. The battery lasts about 60h and can charge while in use Details: hands-free communication, following § 23 (1a) of the German road traffic regulations. This paragraph outlaws the usage of handheld microphones since the 01.07.2020 active noise canceling, eliminating irritating background noises VOX sensitivity adjustable in 4 levels VOX delay adjustable in 4 levels impedance: 4.7K ohm sensitivity: -58db 3000mAh battery (rechargable) 60h battery life micro-USB charging port Up/Down button plug: 4-point connector Scope of delivery:VOX microphone, instructions, USB charging cable Compatible with:Midland M10, Midland M Zero Plus, Alan 100 Plus B, diverse Präsident Geräte, Lavayette, etc.

Mini CB radio with microphone AE6110 from Albrecht The ALBRECHT AE 6110 has all the essential functions that you need. The highlight: With a width of only 10 cm and a height of 2.5 cm, it can easily be accommodated even in the smallest of spaces. With its die-cast housing, it is very stable. New: with integrated VOX function for hands-free speaking in the vehicle Properties: All European CB standards S-meter, 6-level LED indicators for RX and TX VOX hands-free function Receiving sensitivity adjustable (RF gain) Channel 9/19 direct selection button (EMG) Die cast housing 4 watt AM / FM Automatic squelch (ASQ), adjustable in 9 levels Further equipment features: Channel selection buttons on the microphone Channel search (scan) Keylock Socket for external speaker Technical specifications:Dimensions: 102 x 100 x 25 mm³Weight: 450 gSupply voltage: 13.2 V.Power consumption: 2 A max.Operating temperature range: -20 to +50 ° CAntenna input: UHF, SO-239Frequency error: <+/- 300 HzTransmission power: 4 wattsInterference transmissions: <4 nW (-54 dBm)Adjacent channel power: <20 µWFM frequency deviation: <1.9 kHzAM modulation depth: <90%Reception sensitivity: better than 1 μV (20 dB SINAD)Mirror selection: 70 dBAdjacent channel suppression: 60 dBAudio output: 1 watt into 8 ohmsFrequency response: 300-3000 Hz Conversion option for licensed amateur radio operators:10 m amateur radio band, 400 channel mode: 25,610-30,105 MHz, 8 watts Scope of delivery: AE 6110 CB radio, microphone with up / down buttons, microphone holder, mounting bracket with screws, instructions

Defender CB antenna mount – air intake mount, magnetic or fixed This mounting plate optimally attaches a CB antenna to the air intake of the Land Rover Defender. For this purpose, the mounting plate is installed on the left (as seen from the driver's seat) ventilation grille / on the air inlet. For right-hand drive vehicles (UK), please contact us by phone or e-mail. Please select the suitable variant for you: fixed mounting or as a magnet. Delivery: mounting plate 1 m ground cable mounting material

This CB mobile antenna scores with good SWR values - the fine-tuning of the SWR values is done by rings. Technical data: CB mobile antenna 1/4 lambda 120 channels Power rating: 40 watts Material: Stainless steel SWR Adjustable YES Length: 115 cm Cable length: 4 metres For fixed mounting The antenna has a cable with an open end to make it easier to lay the cable. For connection to a radio, you still need a PL259/6 plug for RG58 coaxial cable.

Magnetic base antenna for CB radio, approx. 145 cm long. Technical data: Type: 5/8 LambdaPower rating: 200 WLength of steel: 148 cmRadiator material: stainless steelMagnetic base: 120 mm diameterThe antenna has a cable with an open end to make it easier to lay the cable. For connection to a radio set you still need a PL259/6 plug for RG58 coaxial cable.

Permanently good reception with the CB fixed mounting antenna The 1/4 lambda antenna is easy to mount and offers a wide bandwidth incl. DV connection. It consists of a stainless steel radiator with flux points and a wing nut. The standing wave ratio is preset and can be changed by changing the radiator length. Mounting instructions: Drill a hole with a diameter of 12 mm at a point on the vehicle body.Deburr the hole and ensure a good conductive connection of the antenna flux.Then insert the antenna base from the outside of the body into the hole so that the corrugated side of the antenna joint faces the outside of the vehicle. Fit the plastic washer and the metal trident washer the right way round. Fit the toothed washer and screw on the nut loosely After aligning the base, tighten the nut on the inside of the body with a spanner Screw on the angle plug with the antenna cable (tip: seal with silicone to permanently seal the mounting point against rust) Mount the radiator with the threaded bolt on the antenna base Technical data: Frequency: MHz 26-28 Type: 1/4 Lambda Power rating: 300 W Radiator length: 130 cm Steel material: Stainless steel SWR Adjustable - SWR adjustment via length change: SWR preset Special features: Plug type DV Total length with base: 138 cm The antenna has a cable with an open end to make it easier to lay the cable. For connection to a radio set you still need a PL259/6 plug for RG58 coaxial cable.

Alan PL259/6 plug, for RG58 coaxial cable PL259/6 plug, double pack, for assembling RG58 antenna cables.Required for the Alan ML130 and Alan ML145 magnetic antenna.

Bracket for CB antenna / radio antenna for Nakatanenga CargoBear system roof rack This robust bracket was specially developed for mounting a CB or radio antenna on CargoBear system roof racks. It is made of high-quality stainless steel and is powder-coated in black for additional corrosion protection and an attractive appearance. Ideal for off-road enthusiasts, long-distance travellers or professional use - with this mount you can securely and stably attach your antenna to the vehicle.Product details:  Suitable for all CargoBear 1 and 2 roof rack systems  Made of rust-free stainless steel  Surface: black powder-coated  Resistant to weather and mechanical stress  Simple and secure attachment  Can be used universally for various CB or radio antenna models Scope of delivery:1x antenna holder (without antenna)Note:The delivery does not include the antenna. The indicated price refers to one piece.

Radio 90 CB antenna for fixed mounting Technical data:  Length approx. 90 cm 200 W 4 m cable with DV plug 1/4 lambda The antenna has an open-ended cable to make it easier to lay the cable. A PL259/6 plug for RG58 coaxial cable is required for connection to a radio.