Lifting spring kit for INEOS Grenadier from TREKFINDER WITH cable winch + 30 mm

TREKFINDER wheel spacer kit for INEOS Grenadier + 66 millimetres Track widening 66 mm by fitting spacer rings on the front and rear axle or only on the rear axle in conjunction with alloy wheels or standard INEOS Grenadier steel wheels. The following vehicles are approved according to the TÜV parts certificate: Vehicle manufacturer: Ineos Automotive (UK) / 2295Vehicle type: GN, GMCommercial designation/version: INEOS GRENADIER 6-cylinder diesel & petrol engine, 2+5 seaterEC - TG - No. : e9*2018/858*11384*... ; e9*2018/858*11385*... The following wheel/tyre combinations are approved according to the TÜV parts certificate: 265/70R17 with 7.5x17255/70R18 with 8.0x18 Scope of delivery: Selectable: 2 pieces (1 axle) or 4 pieces (2 axles) Aluminium wheel spacer plates, black anodised1 set of fixing nuts1 set of fitting and care instructions1 TÜV parts certificate Notes on installation:The screw-in length of all fastening elements must be at least 7.5 turns (M14x1.5).Ensure that the stud bolts are long enough.The bolted-on spacer rings are fastened to the vehicle using the fastening elements supplied by the spacer ring manufacturer (M14x1.5 tapered collar). The standard wheels are fastened with the standard fastening elements.The standard stud bolts may protrude slightly (up to 2 mm) beyond the wheel contact surface of the spacer rings. In conjunction with the standard Ineos steel wheels or LM wheels without "cast pockets", which can accommodate the standard stud bolts and nuts protruding beyond the wheel contact surface, the standard stud bolts must be shortened slightly. The minimum screw-in length of all fastening elements of 7.5 turns must be maintained. Wheel cover requirements:Adequate coverage of the wheel/tyre combination must be achieved by fitting 35 mm wide, permanently attached wheel cover extensions.The surface-mounted wheel cover extensions must be fitted at an angle of 30 degrees to the front and 50 degrees to the rear in relation to the vertical centre line of the wheel. Notes on the modification measure:There are no technical objections to the use of standard or other wheel/tyre combinations up to the above (limit) wheel/tyre combinations in conjunction with the described spacer rings if the following conditions are met: - Separate suitable expert reports are available for the wheel/tyre combinations and the conditions listed therein are complied with. In addition, the above-mentioned conditions must be observed and applied if necessary.- If other wheel/tyre combinations are used, their suitability (freedom of movement, driving behaviour, etc.) must be checked and verified separately.- There are no technical objections to the additional use of tested lowered or raised suspension (with parts certificate or ABE). In the case of suspension modifications with non-standard end stops, the suitability of the conversion must be checked or verified separately.  

Nakatanenga CargoBear for Ineos Grenadier The launch of the Ineos Grenadier was without a doubt the biggest event for the off-road community since the launch of the new Defender. And since the two are more or less officially competing for the title of best successor to the old Landy, it's a pretty exciting affair. When it comes to the shape of the roof, the new Ineos is hardly distinguishable from the old Defender, including the slope at the front, the side gutters and the mighty roof load of 150 kg (dynamic load) and 420 kg (static). All of that makes it a joy to fit the Grenadier with our CargoBear modular roof rack. The legendary CargoBear is just as ambitious and versatile as the British newcomer with its Bavarian-Austrian technology and old-school look. The CargoBear for the Grenadier (Station Wagon/Utility Wagon) can be ordered in four variations – but thanks to our modular system, subsequent conversions or add-ons are easily done, whenever your specific requirements change. In the simplest, open version, the roof rack consists of three crossbars, a wind deflector at the front and the end carrier at the rear. For closed and therefore fully accessible platforms, the Bear is available in three further versions: As a short roof rack with three crossbars, two closed sections between the bars, a wind deflector and end panel. As a long version with four crossbars, three closed sections between the bars, a wind deflector and end panel. There is also a special version for grenadiers with safari windows in the front roof. Here the rear two sections are fully closed, the front one has two openings on the sides, so as not to obstruct the safari windows. As with the old Landy, the ultra-flat roof rack is simply mounted to the roof gutters by clamping brackets. A hybrid solution specially adapted to the Grenadier provides even more stability: additional U-profiles and support brackets connect the CargoBear to the handles on the roof to take excessive load off the gutters. As always, all aluminum and stainless steel components of the CargoBear are powder-coated in black. This makes them a perfect match for the purist design of the Grenadier. Ineos Grenadier and CargoBear - the ultimate combination for work, sport, camping or expedition! The Trier Fire Brigade also relies on our quality – equipment that meets the highest standards! Material:Crossbar, platform, wind deflector and end panel: powder-coated aluminum (black)U-profiles and support brackets: Stainless steel powder-coated (black) MADE IN GERMANY

Sun visor organizer for Ineos Grenadier With its classic boxy design – inspired by the old Defender, of course – the Ineos Grenadier is as spacious as can be. And there’s the catch, because it is very easy to lose track of all your small and important things in the Grenadier’s huge cockpit. But now there’s an easy solution available: our practical organizer for the sun visor features a spacious zipper pocket, MOLLE and Velcro patches. All your essential vehicle documents, parking licenses, keys, pens, sunglasses and other small paraphernalia can be kept within easy reach at all times, without restricting your forward vision or driving attention in any way. Four sturdy Velcro straps guarantee a tight fit on the sun visor, even in rugged off-road terrain. The organizer is made of PU coated nylon 6.6 fabric and therefore extremely durable and easy to clean. Available in black Dimensions:on the sun visor: 46.5 cm x 16.5 cmopen: 46.5 cm x 33 cm Each organizer has to be ordered separately.

Standard main beam headlights do the job as long as the road runs straight to the supermarket. Once the tarmac ends, everything left and right of the track goes dark fast. And from that point on, the terrain tends to keep surprises ready, for example a deer that doesn't see the off-roader coming, or a road edge that suddenly drops away into a deep ditch. The Vision X CG2 CPM710 Light Cannon make those surprises visible: multi-LED driving lights for the Ineos Grenadier, built for short and medium range. The beam of the Vision X auxiliary driving lights for the Grenadier Each lamp holds seven LEDs of 7 watts each, every one with its own 10° optic, and together they produce a wide driving beam. That works out to 49 watts per lamp, so 98 watts as a pair. Colour temperature sits at 6,000 Kelvin, which gives the light a clear, neutral-white character. Anyone looking for range rather than width should take a look at the single-LED sibling, the Vision X CG2 CPZ110. Clear or yellow lens? The Vision X auxiliary driving lights for the Grenadier come with either a clear or a selective yellow lens. Clear delivers the full light output and is the standard choice for clear nights. The yellow version is built for the days when something is hanging in the air, like dust on a desert track, mist in the mountains, driven snow on a pass, or heavy rain in the forest. Yellow light scatters less on particles in the air and therefore does not build the blinding wall in front of the bonnet that clear light can throw up when visibility drops. Housing waterproof and tough The housing of the CG2 CPM710 is a hybrid of aluminium and polycarbonate, tough enough for stone chips and light enough for the grille. The lens is acrylic, and together the lamps are IP68 waterproof and IP69K pressure-washer tested, stand up to 21.2 Grms of vibration, and operate between minus 40 and plus 80 degrees Celsius. The LEDs are rated for around 50,000 hours. Fitment in the grille, no drilling Vision X developed this kit specifically for the Ineos Grenadier and tested it on the vehicle in Europe. The lamps sit neatly in the grille with the supplied brackets, with no drilling or cutting required, so parking sensors and driver assistance systems stay fully functional. The plug-and-play wiring loom brings everything needed, including relay, fuses, and a CAN-bus connection, so the driving lights switch on automatically or manually together with the main beam. Anyone who wants to revert to the original setup can do so at any time. Technical specification Dimensions (L × W × H): 14.5 cm × 9.4 cm × 13.4 cm Manufacturer: Vision X LED type: 7 × 7 W LEDs, each with 10° optic (multi-LED) Power: 2 × 49 W (98 W as a pair) Luminous flux: 10,500 lumens total Range: approx. 215 m Beam type: wide driving beam Colour temperature: 6,000 K Lens: acrylic, clear or selective yellow Input voltage: 9 to 32 V DC Current draw: 4.08 A per lamp at 12 V (8.17 A as a pair), 2.04 A at 24 V Weight: 1.3 kg per lamp Housing: hybrid (aluminium and polycarbonate) Protection rating: IP68 waterproof, IP69K pressure-washer tested Vibration rating: 21.2 Grms Operating temperature: −40 °C to +80 °C Lifespan: around 50,000 hours Certifications: CE, RoHS, IEC 62471, ECE R112 (driving lamp) Connector: Deutsch connector In the box: 2 driving lights with connection cable

BORBET demonstrates a seventh sense for high wheel loads with the new CW7 design. With the BORBET CW7 in the "Commercial Wheels" category, a new wheel is now presented that is not only convincing in terms of design, but also with high wheel loads of up to 1,400 kg.The CW7 stands for a new, striking look that is not only defined by the number of spokes, but is also made for the real movers and shakers among vehicles. From vans to off-roaders to motorhomes. Manufacturer: Borbet Brand: CW7 Size/offset: 7.5x18", offset 47 Colour: either matt black or matt bronze Suitability: for Ineos Grenadier Certification: for 255/65R18,  255/70R18;  265/65R18; A01) K02) Included in delivery: Rim, incl. matching wheel nuts High wheel load Winterproof Scope of delivery: rim 16 inch, incl. matching wheel nuts Note: the wheel nuts of the original Ineos alloy rims also fit on these rims!

The Rockslider for the INEOS Grenadier is made of stainless steel in Germany and impresses with its function and striking design. In order to increase the stiffness in the event of a lateral load in off-road use, the lateral slotted holes are turned inwards. Mounting is done on original mounts without drilling.The Rockslider is mounted directly underneath the doors instead of the plastic trim. Due to the high exposed position of the Rockslider, the ramp angle of the INEOS Grenadier is not changed or impaired. Our Rockslider not only serves to protect the bodywork, but also provides a secure footing thanks to its non-slip surface made of drawn nubs. Due to its shape, the Rockslider also protects against excessive dirt in the field. The dirt collected can be rinsed out again through openings on the underside. The Rockslider, as well as the two holders - made in Germany - are powder-coated in black or red and can be ordered in the combination that matches the vehicle. Suitable forUtility 2 & 5-seaterStation Trial & Fieldmaster Technical data:25 kg per Rockslider incl. bracketMounting on original mounting points Delivery:1 set Rockslider stainless steel (left & right)Bracket and mounting material (left & right)Set of stainless steel screws As a useful add-on, there are matching anti-slip pads for the Rockslider.

Ventilation plates rear side windows - Ineos Grenadier The INEOS Grenadier stands for uncompromising off-road capability and robustness. Good air circulation, as with slightly open windows, but without the increased risk of rainwater ingress or theft? Plus effective insect protection? That's exactly what our ventilation panels with mosquito netting offer, precision-manufactured for the Grenadier from high-quality aluminium — no rattling universal parts. Supplied in pairs, powder-coated in black and visually unobtrusive, they are ideal for expeditions, camping and tough use. Installation: wind down the windows, insert the panels, wind up the windows. Installation is straightforward: roll down the window, insert the ventilation panel, close the window again – and it's securely in place without rattling. ⚠️ Important note: Children and animals must never be left in the vehicle at high temperatures, even with the ventilation panels in place. Length: 520 mm <iframe width="560" height="315" src="https://www.youtube.com/embed/qWKDhVh_0n0" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>

Lowering spring kit TREKFINDER for INEOS Grenadier - approx. 30 millimetres the lowering is approx. 30 millimetres suitable for 6-cylinder diesel & petrol engines for vehicles WITHOUT winch the standard shock absorbers can still be used Trailer operation is permitted Suitable for the following versions: Vehicle manufacturer: Ineos Automotive ( UK ) Commercial designation / version: INEOS GRENADIER Permissible axle loads ( v / h ) in kg: 1667 / 2150 Vehicle type / make: GM with EG-TG-No.: e9*2018/858*11384*... Vehicle type / make: GN with EG-TG-No.: e9*2018/858*11385*... Scope of delivery: 4 pieces TREKFINDER coil springs ( HA progressive and VA linear ) 1 piece TÜV® parts certificate

Lifting spring kit TREKFINDER for INEOS Grenadier + approx. 30 millimetres the lift is approx. 30 millimetres suitable for 6-cylinder diesel & petrol engines for vehicles WITHOUT cable winch the standard shock absorbers can still be used Trailer operation is permitted Suitable for the following versions: Vehicle manufacturer: Ineos Automotive ( UK ) Commercial designation / version: INEOS GRENADIER Permissible axle loads ( v / h ) in kg: 1667 / 2150 Vehicle type / make: GM with EG-TG-No.: e9*2018/858*11384*... Vehicle type / make: GN with EG-TG-No.: e9*2018/858*11385*... Scope of delivery: 4 pieces TREKFINDER coil springs ( HA progressive and VA linear ) 1 piece TÜV® parts certificate <iframe width="1188" height="668" src="https://www.youtube.com/embed/Ex0-px1m0LE" title="INEOS GRENADIER Höherlegungsfedernsatz (+30mm) von TREKFINDER und H&amp;R" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" allowfullscreen></iframe>