TREKFINDER wheel spacer kit for INEOS Grenadier + 66 millimetres Track widening 66 mm by fitting spacer rings on the front and rear axle or only on the rear axle in conjunction with alloy wheels or standard INEOS Grenadier steel wheels. The following vehicles are approved according to the TÜV parts certificate: Vehicle manufacturer: Ineos Automotive (UK) / 2295Vehicle type: GN, GMCommercial designation/version: INEOS GRENADIER 6-cylinder diesel & petrol engine, 2+5 seaterEC - TG - No. : e9*2018/858*11384*... ; e9*2018/858*11385*... The following wheel/tyre combinations are approved according to the TÜV parts certificate: 265/70R17 with 7.5x17255/70R18 with 8.0x18 Scope of delivery: Selectable: 2 pieces (1 axle) or 4 pieces (2 axles) Aluminium wheel spacer plates, black anodised1 set of fixing nuts1 set of fitting and care instructions1 TÜV parts certificate Notes on installation:The screw-in length of all fastening elements must be at least 7.5 turns (M14x1.5).Ensure that the stud bolts are long enough.The bolted-on spacer rings are fastened to the vehicle using the fastening elements supplied by the spacer ring manufacturer (M14x1.5 tapered collar). The standard wheels are fastened with the standard fastening elements.The standard stud bolts may protrude slightly (up to 2 mm) beyond the wheel contact surface of the spacer rings. In conjunction with the standard Ineos steel wheels or LM wheels without "cast pockets", which can accommodate the standard stud bolts and nuts protruding beyond the wheel contact surface, the standard stud bolts must be shortened slightly. The minimum screw-in length of all fastening elements of 7.5 turns must be maintained. Wheel cover requirements:Adequate coverage of the wheel/tyre combination must be achieved by fitting 35 mm wide, permanently attached wheel cover extensions.The surface-mounted wheel cover extensions must be fitted at an angle of 30 degrees to the front and 50 degrees to the rear in relation to the vertical centre line of the wheel. Notes on the modification measure:There are no technical objections to the use of standard or other wheel/tyre combinations up to the above (limit) wheel/tyre combinations in conjunction with the described spacer rings if the following conditions are met: - Separate suitable expert reports are available for the wheel/tyre combinations and the conditions listed therein are complied with. In addition, the above-mentioned conditions must be observed and applied if necessary.- If other wheel/tyre combinations are used, their suitability (freedom of movement, driving behaviour, etc.) must be checked and verified separately.- There are no technical objections to the additional use of tested lowered or raised suspension (with parts certificate or ABE). In the case of suspension modifications with non-standard end stops, the suitability of the conversion must be checked or verified separately.  

Nakatanenga CargoBear for Ineos Grenadier The launch of the Ineos Grenadier was without a doubt the biggest event for the off-road community since the launch of the new Defender. And since the two are more or less officially competing for the title of best successor to the old Landy, it's a pretty exciting affair. When it comes to the shape of the roof, the new Ineos is hardly distinguishable from the old Defender, including the slope at the front, the side gutters and the mighty roof load of 150 kg (dynamic load) and 420 kg (static). All of that makes it a joy to fit the Grenadier with our CargoBear modular roof rack. The legendary CargoBear is just as ambitious and versatile as the British newcomer with its Bavarian-Austrian technology and old-school look. The CargoBear for the Grenadier (Station Wagon/Utility Wagon) can be ordered in four variations – but thanks to our modular system, subsequent conversions or add-ons are easily done, whenever your specific requirements change. In the simplest, open version, the roof rack consists of three crossbars, a wind deflector at the front and the end carrier at the rear. For closed and therefore fully accessible platforms, the Bear is available in three further versions: As a short roof rack with three crossbars, two closed sections between the bars, a wind deflector and end panel. As a long version with four crossbars, three closed sections between the bars, a wind deflector and end panel. There is also a special version for grenadiers with safari windows in the front roof. Here the rear two sections are fully closed, the front one has two openings on the sides, so as not to obstruct the safari windows. As with the old Landy, the ultra-flat roof rack is simply mounted to the roof gutters by clamping brackets. A hybrid solution specially adapted to the Grenadier provides even more stability: additional U-profiles and support brackets connect the CargoBear to the handles on the roof to take excessive load off the gutters. As always, all aluminum and stainless steel components of the CargoBear are powder-coated in black. This makes them a perfect match for the purist design of the Grenadier. Ineos Grenadier and CargoBear - the ultimate combination for work, sport, camping or expedition! Material:Crossbar, platform, wind deflector and end panel: powder-coated aluminum (black)U-profiles and support brackets: Stainless steel powder-coated (black) MADE IN GERMANY Further keywords for this item: cargo-bear, cargobear, CargoBear, roof-rack, roof rack

Sun visor organizer for Ineos Grenadier With its classic boxy design – inspired by the old Defender, of course – the Ineos Grenadier is as spacious as can be. And there’s the catch, because it is very easy to lose track of all your small and important things in the Grenadier’s huge cockpit. But now there’s an easy solution available: our practical organizer for the sun visor features a spacious zipper pocket, MOLLE and Velcro patches. All your essential vehicle documents, parking licenses, keys, pens, sunglasses and other small paraphernalia can be kept within easy reach at all times, without restricting your forward vision or driving attention in any way. Four sturdy Velcro straps guarantee a tight fit on the sun visor, even in rugged off-road terrain. The organizer is made of PU coated nylon 6.6 fabric and therefore extremely durable and easy to clean. Available in black Dimensions:on the sun visor: 46.5 cm x 16.5 cmopen: 46.5 cm x 33 cm Each organizer has to be ordered separately.

CG2 Light Cannon headlights are the ultimate off-road lighting solution for your Ineos Grenadier. With a range of sizes from 3.0" to 8.7", each light in this series is designed to meet your specific needs, offering unrivalled performance in all conditions. Key Features : Unmatched Power: These headlamps feature ultra-bright 40W single-source LEDs, delivering a long-distance spot beam. You can count on them to light your way, no matter how dark it gets. Maximum adaptability: Choose between a clear or yellow selective lens to adapt to all weather conditions, whether dust, rain, snow or fog. Maximum visibility is guaranteed. Cutting-edge technology: Thanks to iris reflector technology, these headlights offer unrivalled range. You can drive with confidence, knowing you'll see everything in your path clearly. Superior quality: Our CG2 Light Cannon headlights use the highest quality CREE LEDs for long-term durability and performance. You can rely on them to stay strong in the most demanding environments. Easy Installation: Each pair of headlamps comes with a Plug And Play harness included, which means installation is quick and easy. You'll be ready to go in no time. Unlimited customization: All CG2 round LED light guns are compatible with our 25-light-in-one cover system (sold separately). This lets you change the pattern and color of the light to suit your specific driving environment. Transform your Grenadier into the ultimate off-road machine with CG2 Light Cannon headlights. More power, more visibility, more confidence on any terrain. TECHNICAL DESCRIPTION Dimensions (LxWxH) : 14.5 cm x 9.4 cm x 13.4 cm Input voltage: 9-32V DC AMP consumption: 8.17 A Power: 98 W Gross Lumens: 10,500 lm Illumination distance: 279.4 m Beam type: Wide beam and spot beam

BORBET demonstrates a seventh sense for high wheel loads with the new CW7 design. With the BORBET CW7 in the "Commercial Wheels" category, a new wheel is now presented that is not only convincing in terms of design, but also with high wheel loads of up to 1,400 kg.The CW7 stands for a new, striking look that is not only defined by the number of spokes, but is also made for the real movers and shakers among vehicles. From vans to off-roaders to motorhomes. Manufacturer: Borbet Brand: CW7 Size/offset: 7.5x18", offset 47 Colour: either matt black or matt bronze Suitability: for Ineos Grenadier Certification: for 255/65R18,  255/70R18;  265/65R18; A01) K02) Included in delivery: Rim, incl. matching wheel nuts High wheel load Winterproof Scope of delivery: rim 16 inch, incl. matching wheel nuts Note: the wheel nuts of the original Ineos alloy rims also fit on these rims!

The Rockslider for the INEOS Grenadier is made of stainless steel in Germany and impresses with its function and striking design. In order to increase the stiffness in the event of a lateral load in off-road use, the lateral slotted holes are turned inwards. Mounting is done on original mounts without drilling.The Rockslider is mounted directly underneath the doors instead of the plastic trim. Due to the high exposed position of the Rockslider, the ramp angle of the INEOS Grenadier is not changed or impaired. Our Rockslider not only serves to protect the bodywork, but also provides a secure footing thanks to its non-slip surface made of drawn nubs. Due to its shape, the Rockslider also protects against excessive dirt in the field. The dirt collected can be rinsed out again through openings on the underside. The Rockslider, as well as the two holders - made in Germany - are powder-coated in black or red and can be ordered in the combination that matches the vehicle. Suitable forUtility 2 & 5-seaterStation Trial & Fieldmaster Technical data:25 kg per Rockslider incl. bracketMounting on original mounting points Delivery:1 set Rockslider stainless steel (left & right)Bracket and mounting material (left & right)Set of stainless steel screws As a useful add-on, there are matching anti-slip pads for the Rockslider.

Ventilation plates rear side windows - Ineos Grenadier The INEOS Grenadier stands for uncompromising off-road capability and robustness. Good air circulation, as with slightly open windows, but without the increased risk of rainwater ingress or theft? Plus effective insect protection? That's exactly what our ventilation panels with mosquito netting offer, precision-manufactured for the Grenadier from high-quality aluminium — no rattling universal parts. Supplied in pairs, powder-coated in black and visually unobtrusive, they are ideal for expeditions, camping and tough use. Installation: wind down the windows, insert the panels, wind up the windows. Installation is straightforward: roll down the window, insert the ventilation panel, close the window again – and it's securely in place without rattling. ⚠️ Important note: Children and animals must never be left in the vehicle at high temperatures, even with the ventilation panels in place. Length: 520 mm <iframe width="560" height="315" src="https://www.youtube.com/embed/qWKDhVh_0n0" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>