Complete wheel set BF Goodrich 265/65R18 117R All Terrain T/A KO2 on Borbet CW7 alloy wheels BFGoodrich ALL Terrain T/A KO2 265/65 R18 117R: The BFGoodrich All Terrain T/A KO2 265/65 R18 117R guarantees driving fun even off the paved roads. It is very stable and has good road grip. It also handles not too difficult terrain with some mud, loose ground well. For extreme terrain and little road use, however, a MUS tyre is recommended. In the AT range BFGoodrich is a very good choice. A SPECIAL TYRE MIXTURE that is resistant to cuts and chipping on the sidewalls to withstand sharp stones. Designed to resist chipping and cracking caused by sharp stones and obstacles in the terrain. IMPRINTED CLAMPS on the sides for more grip and better sidewall protection. The large crampons on the sidewall are synonymous with bite, especially when the tyre is rolling at low pressure. Greater thickness of rubber on the sidewall protects the tyre from off-road hazards. STRENGTHENED CABLES for less sensitive sidewalls. Flank weakness can spoil off-road activities very quickly. Oversized sidewall cables give the carcass the protection it needs for tough off-road use. Performance 50% off-road - 50% on-road Tyre width 265 Ratio of sidewall height to tyre width in percent 65 Rim diameter: 18" Load index: 117/114 Speed index: R 3PMSF Alpine symbol (so-called snowflake): yes M+S marking: yes Weight: 23,06 per tyre Tyre type: All-season Tyre type: Radial Noise emission: 74db Noise class (from 1-quiet to 3-noise): 2 Wet grip (grip on rain-soaked road): B Fuel efficiency (A to G): F When ordering, please let us know whether the white lettering is to be fitted inside or outside.BORBET CW7 alloy wheels 18 inch:With the BORBET CW7 in the "Commercial Wheels" category, a new wheel is now presented that is not only convincing in terms of design, but also with high wheel loads of up to 1,400 kg.The CW7 stands for a new, striking look that is not only defined by the number of spokes, but is also made for the real movers and shakers among vehicles. From vans to off-roaders to motorhomes. Manufacturer: Borbet Brand: CW7 Size/offset: 7.5x18", offset 47 Colour: either matt black or matt bronze Suitability: for Ineos Grenadier Certification: for 255/65R18 255/70R18 265/65R18 A01) K02) Included in delivery: Rim, incl. matching wheel nuts High wheel load Winterproof Scope of delivery: Rim, incl. matching wheel nuts / Note: the wheel nuts of the original Ineos alloy rims also fit on these rims!The price refers to 4 or 5 complete wheels incl. mounting and balancing. This article is bulky goods.

Your tyre for extreme conditions: BFGoodrich KM3 Offroad Goodrich Mud Terrain T/A KM3 255/85R16 119QThe off-road tire BFGoodrich Mud Terrain T / A KM3 is primarily intended for off-road use, it is less suitable for driving on paved roads. The tires of this type are characterized by a special tread, which is responsible for safety when driving off-road, as well as a reinforced construction. The MT tires are the best way out for drivers who need tires for mud and water when driving off-road and are not afraid of rocky slopes. The very deep grooves of the tread and the massive blocks make driving on these tires safe. Due to the wide gaps, the tire cleans itself up quickly, which makes driving easier on sand, for example. This typical terrain model is also reinforced so that drivers do not have to worry about the tire being destroyed when driving in difficult terrain. Available in:255/85 R16235/85 R16 click here LR WOLF Steel Wheel 6.5x16"- corresponds to part number ANR4583 PM- dimensions 6,5 x16", offset 20,6TPMS sensor Alcar Plug & DriveTire pressure monitoring systems (TPMS) or Tire Pressure Monitoring Systems (TPMS) are systems built into motor vehicles for the constant monitoring of tire pressure. A distinction is made between direct (measure the tire pressure with a sensor in the wheel) and indirect (measure via the vehicle's ABS sensors) systems. If a pressure loss occurs in one or more tires, the driver is informed of this directly on the display inside the vehicle. TPMS fulfill four functions: They increase driving safety through better grip, more stable steering behavior and shorter braking distances You avoid increased fuel consumption due to incorrect tire pressure They prevent increased tire wear caused by insufficient tire pressure They reduce CO² emissions through lower fuel consumption and longer tire life If the wheels need to be rebalanced at a later date, we recommend balancing the rims for the Land Rover Defender using bolt or bolt circle centring.

BF Goodrich All Terrain T/A KO3 all-season tyre on Wolf steel rim Tyre size: 235/85R16 Rim size/offset: 6.5x16" T20.6   BFGoodrich® All-Terrain T/A KO3 - One tyre for all occasions.   Wherever the journey takes you: the BFGoodrich® All-Terrain T/A KO3 is ready for action. This 3PMSF-certified tyre offers strong grip on mud and snow. With its serrated tyre shoulder design and mud phobic bars, it also contributes to controlled handling on and off the road. Brand: BFGOODRICH Tread pattern: ALL-TERRAIN T/A KO3  Dimension: LT235/85R Diameter: 16" Load index: 120 Speed index: S Fuel efficiency class: E Wet grip class: C External rolling noise classification: B External rolling noise: 74 dB Snowflake symbol: yes   Resistance on a new level.  BFGoodrich® all-season off-road tyres for SUVs, off-road vehicles and light trucks Designed for high grip and controlled handling on and off-road CoreGard technology and improved rubber compound for increased resistance and durability Optimised tread design for even wear and longer service life Off-road design for increased off-road performance All-season tyre When ordering, please let us know whether the white lettering should be mounted on the inside or outside.   We recommend to balance the rims for the Land Rover Defender bolt or bolt circle centred.   The rims used are LR WOLF rims (black) 6.5x16 inch, offset 20.6, which correspond to part number ANR4583 PMGEN. These are the ORIGINAL rims from Land Rover (not a replica!). These black rims can also be ordered powder-coated in the colour white or black.   Note: We always recommend the powder-coated rims, as the rims with a primer are still susceptible to corrosion due to the open pores alone. If the primed rims corrode, there is therefore no right of return.    Please note: Wheel nuts for aluminium rims cannot be used on steel rims.   Balancing Defender wheels on conventional centre-centring balancing machines often leads to errors. For this reason, we use a so-called stud centring system, in which the wheel is balanced using a special adapter plate.    

Mobile parking heater with aluminum box, various versions Make way, here comes the second generation of our mobile parking heaters in a box! We have packed even more technology, even more experience and even more customer feedback into our new mobile heating boxes. If you are looking for a small, self-sufficient and portable heat source with unrivaled capacity for cold days and nights in unheated outdoor shelters or temporary accommodation, you get everything you need (or want) in a small, weatherproof aluminum box. Available in three modular versions with different configurations, the Nakatanenga heating box provides the perfect, independent heat source for tents, gazebos, garden sheds, mountain huts, snack stands, stalls and much more. The heart of the mobile parking heater is the Autoterm Luft 2D, a diesel-powered air heater with a maximum heat output of 1.8 kW and a diesel consumption of just under a quarter of a liter per hour at full power. With a tank capacity of 18 liters in the twin-tank version, this means that it can heat at full throttle for over 70 hours. The economical unit, which is also very quiet at 55 dB thanks to the exhaust silencer, is controlled by a digital control unit with timer in the version with two batteries and can also be switched on and off by radio remote control. This allows you to preheat your camper, roof tent, caravan or hunting lodge in good time for getting up or for the evening, for example, and operate it from the place where you are staying or sleeping inside*. In contrast to the previous models, the three versions of our mobile parking heater are now only available in one box size, namely 42 liters. This is significantly more compact than the old version in the large version and only slightly more voluminous than the small model from before. What is the advantage? The new universal crate has a modular interior with a powerful performance. Depending on whether you need tanks, batteries or both in the box, you can choose the appropriate version when purchasing: with 9.2 L single or 18.4 L double tank, each without battery, as well as with single tank, two batteries and digital control. However, it can also be easily retrofitted or converted if requirements change. This is made possible by elaborately designed brackets in the box and the use of specially manufactured, made-to-measure tanks.   Features of heating box 1 and 2 (without battery) - USB interface for charging smartphone, power bank, tablet, etc.- Capacity display- PU5 control panel (without timer and storage options)- 12 V connection socket for supplied pole terminal cable- Alternatively, a cable for cigarette lighter (KMSH cable) can be used- 2 radio remote controls- Connection option for external temperature sensor (the connection is inside the box, not outside)”   Features of heater box 3 (with 2 AGM batteries) - USB interface for charging smartphone, power bank, tablet, etc.- Capacity display- Comfort Control control panel (with timer and memory option)- SAE connection socket (suitable for Optimate chargers or Optimate solar charger)- 2 radio remote controls- Connection option for external temperature sensor (the connection is inside the box, not outside)   Equipment of heating box 4 (with 1 LiFePo battery) - USB interface for charging smartphone, power bank, tablet etc.- Capacity display- Comfort Control control panel (with timer and memory option)- SAE connection socket (suitable for Optimate chargers or Optimate solar charger)- 2 radio remote controls- Connection option for external temperature sensor (the connection is inside the box, not outside)-> Please only use LiFePo-compatible chargers Equipment of heating box 5 (with 2 LiFePo batteries) - USB interface for charging smartphone, power bank, tablet, etc.- Capacity display- Comfort Control control panel (with timer and memory option)- SAE connection socket (suitable for Optimate chargers or Optimate solar charger)- 2 radio remote controls- Connection option for external temperature sensor (the connection is inside the box, not outside)”-> please only use LiFePo-compatible chargers The warm air is transported via a firmly screw-fastened, waterproof Flexi hose. As the warm air hose is different for every user and every requirement, we do not include a standard length, but leave it up to you to order the desired length separately here in the store, with or without a silicone sleeve. You can find the perfect storage bag for the Flexi hose here in the store. Regardless of the configuration, the mobile parking heaters are always easy to transport and make the difference between experiencing and suffering in the cold seasons. Whether it's an aurora safari, selling cookies at the Christmas market or winter camping in a roof tent, nothing is really fun if you freeze to death. *ATTENTION: As a precaution, we would like to point out that operation in closed rooms is not permitted due to the risk of poisoning from exhaust fumes. In addition, for optimum heating performance, make sure that the air inlets for combustion and hot air are positioned so that they are protected from the weather. Dimensions Internal dimensions 550x350x220 mm External dimensions 580x380x240 mm Empty weight: 2 tanks, without battery: 18 kg 1 tank, without battery: 16 kg 1 tank, 2 batteries: 36 kg Depending on how many starts are made, the battery lasts at least 40 h, but more likely between 60 and 70 h.  LiFePo4 batteries - i.e. batteries with a lithium iron phosphate cathode - are the ideal supply batteries for camping or electrical work on the move. In contrast to conventional lead-acid AGM technology, lithium batteries combine superior charging properties with much lower weight and volume and a long service life. LiFePo4 batteries can be deep-discharged without any problems, which sooner or later leads to irreparable damage with AGM batteries, as the rule of thumb here is that you should never draw more than 50% charge. If you are not dependent on the greater cold tolerance of AGM batteries, you should definitely consider the higher costs for LiFePo4 batteries and compatible charging technology. The weight and space savings, the long service life and the uncomplicated discharging and charging of the battery are strong arguments in favor of the investment. What's more, LiFePo4 technology is also extremely safe And a special note on aluminum: Although we take the utmost care during storage and shipping, as with all our products, aluminum boxes can always show minimal scratches, stains, dents or other surface features upon delivery. These are material-related and result from the specific properties of the light metal.  In contact with oxygen, aluminum forms a natural, corrosion-protecting patina and is also relatively soft compared to steel, which is three times heavier. This makes the material ideal for use in sheet metal, especially when weight and resistance are important. On the other hand, however, it also means that aluminum can never be completely free of patina or other marks, even on delivery: Small scratches, stains etc. therefore do not constitute grounds for complaint. Ultimately, aluminum boxes are intended to be robust objects of daily use. Like everything that is actively used, they develop an individual patina and every trace of use tells a story. So, have fun with it! If you want to heat the interior of your vehicle, we offer an installation service for warm air ducting through a ventilation plate.   Please note the variants without batteries:  Most portable power stations or battery boxes (such as Goal Zero, Eco Flow, Bluetti etc.) are unfortunately not suitable for operating mobile parking heaters. The heater requires up to 15A as starting current and when shutting down, but very few battery boxes can provide this. Suitable battery boxes for operating the mobile parking heater Please note the legal information on batteries HERE. For certain types of batteries, we are legally obliged to charge a deposit.            

BF Goodrich All Terrain T/A KO3 all-season tyre on ANR CLASSIC steel rim Tyre size: 265/75R16 Rim size/offset: 8x16" offset 0   BFGoodrich® All-Terrain T/A KO3 - One tyre for all occasions.   Wherever the journey takes you: the BFGoodrich® All-Terrain T/A KO3 is ready for action. This 3PMSF-certified tyre offers strong grip on mud and snow. With its serrated tyre shoulder design and mud-repellent Mud Phobic Bars, it also contributes to controlled handling on and off the road. Brand: BFGOODRICH Tread pattern: ALL-TERRAIN T/A KO3  Dimension: LT265/75R Diameter: 16 inch Load index: 119 Speed index: S Fuel efficiency class: E Wet grip class: C External rolling noise classification: B External rolling noise: 74 dB Snowflake symbol: yes   Resistance on a new level.    BFGoodrich® all-season tyre for off-road driving with SUVs, off-road vehicles and light trucks Designed for high grip and controlled handling on and off-road CoreGard technology and improved rubber compound for increased resistance and durability Optimised tread design for even wear and longer service life Off-road design for increased off-road performance All-season tyre When ordering, please let us know whether the white lettering should be mounted on the inside or outside.   If the wheels need to be rebalanced at a later date, we recommend balancing the rims for the Land Rover Defender using bolt or bolt circle centring.   The tyres are fitted with the popular ANR Classics rims 16 inch. These are optionally available in primed black, powder-coated black and powder-coated white. The ANR Classics were designed with the Landrover history in the background, manufactured exclusively for Nakatanenga and really round off every Defender perfectly. The price refers to 4 or 5 complete wheels incl. mounting / balancing.   This article is bulky goods      

Robust and powerful: BF Goodrich KO2 on Borbet CW7 – the perfect complete wheel set for your INEOS Grenadier BF Goodrich ALL Terrain T/A KO2 265/65 R18 117R:   The BFGoodrich All Terrain T/A KO2 265/65 R18 117R guarantees driving pleasure even off the beaten track. It is very stable and has good road grip. It also copes well in not too difficult terrain with some mud and loose ground. For extreme terrain and little road use, however, a MUS tire is recommended. In the AT area, BFGoodrich is a very good choice.   A SPECIAL TIRES compound that is resistant to cuts and chipping on the sidewalls to withstand sharp rocks. Designed to resist chipping and cracking that can be caused by sharp rocks and obstacles in the terrain. IMPRINTED CLAMPS on the sides for more grip and better sidewall protection. The large crampons on the sidewall are synonymous with bite, especially when the tire is rolling at low pressure. A greater thickness of rubber on the sidewall protects the tire from off-road hazards. REINFORCED CABLES for less sensitive sidewalls. A weak sidewall can spoil off-road activities very quickly. Oversized sidewall cables provide the carcass with the necessary protection for tough off-road use.   Performance 50% off-road - 50% road   Tire width 265 Ratio of sidewall height to tire width in percent 65 Rim diameter: 18" Load index: 117 Speed index: R 3PMSF Alpine symbol (so-called snowflake): yes M+S marking: yes Weight: 23.06 per tire Tire type: All-season Tire construction: Radial Noise emission: 74db Noise class (from 1-quiet to 3-noisy): 2 Wet grip (grip on wet roads): B Fuel efficiency (A to G): F The tires are already mounted on the rims. The white lettering is mounted on the outside!   BORBET CW7 18 inch alloy wheel   The BORBET CW7 in the “Commercial Wheels” category is a new wheel that not only impresses in terms of design, but also with high wheel loads of up to 1,400 kg. The CW7 stands for a new, striking look that is not just defined by the number of spokes, but is perfect for the real movers and shakers among vehicles. From vans to off-roaders and motorhomes.   Manufacturer: Borbet Brand: CW7 Size/offset: 7.5x18", ET 47 Color: matt black Suitability: for Ineos Grenadier Approval: for 255/65R18 255/70R18 265/65R18 A01) K02) Scope of delivery: rim, incl. matching wheel nuts High wheel load Winter-proof Scope of delivery: rim, incl. matching wheel nuts The price refers to 5 complete wheels incl. fitting and balancing. This article is bulky goods.    

BF Goodrich All Terrain T/A KO3 all-season tyre on Dotz steel rim for Defender up to MY2016 Tyre size: 265/75R16 Rim size/offset: 7x16" offset 8   BFGoodrich® All-Terrain T/A KO3 - One tyre for all occasions.   Wherever the journey takes you: the BFGoodrich® All-Terrain T/A KO3 is ready for action. This 3PMSF-certified tyre offers strong grip on mud and snow. With its serrated tyre shoulder design and mud phobic bars, it also contributes to controlled handling on and off the road.   Brand: BFGOODRICH Tread pattern: ALL-TERRAIN T/A KO3  Dimension: LT265/75R Diameter: 16" Load index: 119 Speed index: S Fuel efficiency class: E Wet grip class: C External rolling noise classification: B External rolling noise: 74 dB Snowflake symbol: yes  Resistance on a new level.    BFGoodrich® all-season off-road tyres for SUVs, off-road vehicles and light trucks Designed for high grip and controlled handling on and off-road CoreGard technology and improved rubber compound for increased resistance and durability Optimised tread design for even wear and longer service life Off-road design for increased off-road performance All-season tyre When ordering, please let us know whether the white lettering should be mounted on the inside or outside.   If the wheels need to be rebalanced at a later date, we recommend balancing the rims for the Land Rover Defender using bolt or bolt circle centring.   The rims used are DOTZ DAKAR steel rims in 7x16 inch format with approval for Land Rover Defender 90/110, Range Rover Classic and Discovery, which are available in silver, bronze or black.   Please note: Wheel nuts for aluminium rims cannot be used on steel rims.   The balancing of Defender wheels often leads to errors on conventional centre-centring balancing machines. For this reason, we rely on a so-called stud centring system, which uses a special adapter plate to balance the wheel as if it were mounted on a vehicle.   The price refers to 4 or 5 complete wheels incl. fitting / balancing.   This article is a bulky item.      

Wheel set Dotz Dakar Steel Rim and BFGoodrich All Terrain Tire  A bigger footprint with Dotz Dakar Steel Rims and BFGoodrich All Terrain tires not only suits Defenders, G-Wagons etc. but also the Jimny II GJ HJ, turning tiny Jimny into Big Jim. The fact that the Dotz Dakar has become a classic for all kinds of 4x4‘s is no accident. The steel rim with its timeless design and its high-quality manufacture is tough to beat when it comes to performance, be it a Sahara rally or a weekend trip. Dotz 4x4 designed this rim to be hardwearing and robust above everything else. Whenever the Dakar is released as a new vehicle, you can be sure it has undergone the most rigorous testing regime, giving you the highest quality and extreme durability. The Dotz Dakar is quickly cleaned by hand or pressure washer and due to its special finish it will be very easy on the eye for a long time – something that can’t be said of many steel rims. We are introducing the Dakar’s off-road performance and its classic look now also for the Jimny II GJ HJ and offer the rim with sizes  7x16 inches  with an offset of 0 mil.  A great rim needs an equally great tire and with the BFGoodrich All Terrain there’s no doubt that it’ll be up to the challenge. As a proven all-season multi-purpose tire, the latest T/A KO2 generation boasts even more improvements and better test results over its predecessor: the tire’s sidewalls are 20% more robust, durability doubles on gravel and adds another 15% on asphalt. Traction is also improved with an increase of 10% and 19% for slush/mud and snow, respectively. As far as the look is concerned the tire can be mounted with the white print to the in- or the outside. Certification documents are included. The wheel sets are available with or without spare wheel. The tire is suitable and permitted for winter use. Size:Rim 7 x 16" ET 0.0 Silver wie tire size 225/75R16*Rim 7 x 15" ET 0.0 Silver with tire size 215/65R16 * Required Modifications for 16” Wheel Set This wheel set size requires a suspension raising kit. The speedometer requires a ratio adapter. The wheel arch covers need to be adapted. Please let us know when ordering whether the white lettering is to be mounted inside or outside.

Mobile parking heater without battery and in aluminium box You can find information on hire equipment below. “It's a Thin Line Between Love and Hate” is the old song and this thin line between loving and hating the same thing is definitely the line on the thermometer in winter. If you freeze off the part of your body with an A, you're guaranteed not to enjoy even the fattest fish at the ice hole, the most magical aurora borealis or the greatest fun at the elephant meeting. That's why we have our solution for all outdoor activities in the cold seasons in the Alubox Pro: the AUTOTERM parking heater for on the go! With the exception of the battery, everything you, your family or your crew need for a warm and cozy outdoor feeling in your car, camper or roof tent is in the ultra-robust, waterproof 29L box. At its heart is the affordable and powerful AUTOTERM (Planar) 2D12 air heater, which can be powered from the vehicle battery via the cigarette lighter adapter. It is controlled via the PU5 control element. A 5.4 l fuel tank is already integrated in the box. This makes our mini heater ideal for on the road and mobile use on the vehicle or wherever a weatherproof cable connection to a car battery can be established. The warm air is transported into the room to be heated via a firmly screw-fastened, waterproof Flexi hose, which can be ordered separately in the desired length here in the store. ATTENTION: As a precaution, we would like to point out that operation in closed rooms is not permitted due to the risk of poisoning from exhaust fumes. Furthermore, for optimum heating performance, care should be taken to ensure that the air inlets for combustion and hot air are positioned so that they are protected from the weather. You can find the perfect storage bag for the Flexi hose here in the store.A larger standalone version of this parking heater with integrated battery is available here. You can also hire this parking heater from us.  Alu-Box Pro (29 liters) waterproof/dustproof according to IP54 standard AUTOTERM (Planar) 2D diesel / air heater ✔ Fuel tank (5.4 liters)✔ Hot air pipe connection, non-return valve, outlet and inlet feed-through✔ Including radio remote control✔ The openings for supply and exhaust air and for the power supply are splash-proof (can be closed with a screw cap or rubber plug)Dimensions of the aluminum box: WxHxD 390x340x290mmDimensions of the box with spigot: WxHxD 490x340x290Total weight: 11.2 kgTechnical data of the parking heater:- Fuel type: Diesel- Heating output: max. 1.8kW, min. 0.8kW- Volume of heated air: max. 75m³/h, min. 34m³/h- Fuel consumption during operation: max. 0.24l/h, min. 0.1 l/h- Power consumption during operation: max. 29W, min. 10W- Manual start/stop- Connection to a car battery or another external 12V battery PU-5 control element: - LED for ventilation display- LED for operating display- Temperature adjustable via rotary control The AUTOTERM Air 2D (Planar 2D) is equipped with an altitude kit! This means that the heater automatically reduces the injection volume according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content falls. The maximum heat output decreases in proportion to the amount of oxygen in the air. Roughly speaking, from 2000 meters upwards, the loss of output per 500m altitude is approx. 5%. Manufacturer tests up to 3440m were problem-free. No problems are to be expected up to 4000m. Up to 5000m the software calculates itself - but this could not yet be tested at real altitude. Please note: Most portable power stations or battery boxes (such as Goal Zero, Eco Flow, Bluetti etc.) are unfortunately not suitable for operating the mobile parking heaters.The heater requires up to 15A as starting current and when shutting down, but very few battery boxes can provide this..In general, however, direct connection to the battery terminals is the best solution   If you want to heat the interior of your vehicle, we offer an installation service for warm air ducting through a ventilation plate.   Please note the legal information on batteries HERE. For certain types of batteries, we are legally obliged to charge a deposit.        

CG2 Light Cannon headlights are the ultimate off-road lighting solution for your Ineos Grenadier. With a range of sizes from 3.0" to 8.7", each light in this series is designed to meet your specific needs, offering unrivalled performance in all conditions. Key Features : Unmatched Power: These headlamps feature ultra-bright 40W single-source LEDs, delivering a long-distance spot beam. You can count on them to light your way, no matter how dark it gets. Maximum adaptability: Choose between a clear or yellow selective lens to adapt to all weather conditions, whether dust, rain, snow or fog. Maximum visibility is guaranteed. Cutting-edge technology: Thanks to iris reflector technology, these headlights offer unrivalled range. You can drive with confidence, knowing you'll see everything in your path clearly. Superior quality: Our CG2 Light Cannon headlights use the highest quality CREE LEDs for long-term durability and performance. You can rely on them to stay strong in the most demanding environments. Easy Installation: Each pair of headlamps comes with a Plug And Play harness included, which means installation is quick and easy. You'll be ready to go in no time. Unlimited customization: All CG2 round LED light guns are compatible with our 25-light-in-one cover system (sold separately). This lets you change the pattern and color of the light to suit your specific driving environment. Transform your Grenadier into the ultimate off-road machine with CG2 Light Cannon headlights. More power, more visibility, more confidence on any terrain. TECHNICAL DESCRIPTION Dimensions (LxWxH) : 14.5 cm x 9.4 cm x 13.4 cm Input voltage: 9-32V DC AMP consumption: 8.17 A Power: 98 W Gross Lumens: 10,500 lm Illumination distance: 279.4 m Beam type: Wide beam and spot beam

NOLDEN 7" Bi-LED main headlight kit with two headlamps with low-/high-beam and adaptor for Mercedes G. Available in different colours. Innovative 7" LED main headlight with proven reflector technology combines low- and hight-beam as well as position light in one lamp. Original dimensions and standard H4 socket mean that this is an easy to fit, durable replacement upgrade for any Mercedes G Wagon. Also fits (in some cases with additional apaptors or wiring looms) other vehicles, like Land Rover Defender, various Toyota, Jeep Wrangler JK/TJ/CJ, etc. The integrated electronic driver / control unit makes for easy fitment. NOLDEN headlights are road legal, of course. They have ECE (also known as E-marked) and SAE approval and are available for either LHD (EU version) or RHD (UK version) vehicles. You can choose between light-crome and darker dark-crome looks. Compared to traditional halogen headlights LED lights offer many advantages: higher light output ("more light") more comfortable light ("white light"), closer to sunlight low energy consumption (32/39 W compared to 55/60 W low/high-beam) vibration and shock proof design (especially important for diesel cars or off-road use) never again (ca. 30.000 hrs lifetime) white road Illumination compatible with HID/Xenon one of the brightest LED high and low beam 7“ headlights available Many users of classical vehicles, especially off-road vehicles (Defender, Wrangler, G-Wagon) have been looking for modern headlights with classical looks. Up to now 7“ LED headlights had offered better illumination than halogen headlights, yet they didn't give optimum illumination or were of inferior design. In addition these were often retrofitting solutions that didn't meet OEM specifications. The new NCC 7“ Bi-LED headlight was especially tailored to meet the OEM requirements. All components, from the LED to the plug, are designed and produced accordingly making up a perfect overall system. The design of the 7“ Bi-LED headlights reminds more of a conventional halogen headlight that looks like the well-known classic design. The familiar appearance of the vehicle is thus not changed much and essentially still looks like “OE“. The illumination level of the new NCC 7“ Bi-LED headlight is equally good as that of a Xenon headlight. However, the new NOLDEN headlight system has the big advantage of a lower current consumption, which increases the life of the system significantly thus noticeably lowering the operating costs. In a normal case it can be expected that the life of the NCC 7“ Bi-LED headlight is much longer than that of the vehicle. The ligths don't require headlight adjustment or the headlight cleaning system of the Xenon system, retrofitting with the new NCC 7“ Bi-LED headlight is therefore much easier, faster and in the end less expensive than is the case with the Xenon headlights. Technical details: dimensions in mm: 177 x 152 number of LED: 5 x Osram Automotive output (low-/high-beam): 32 W / 39 W voltage range: 9-32 V lumens calculated: 1,880 lm / 2,400 lm lumens measured: 1,550 lm / 1,700 lm fixing: PAR56 homologation: ECE, SAE front lens: UV resistent polycarbonate hard coated front lens housing: lightweight, rigid alumium housing waterproof: 480 h salt spray tested and fully water proof to IP6K9K NOLDEN Bi-LED main headlights are also suitable and approved for many European, Asian and American motorbikes. The Nolden LED lights are available in chrome, dark-chrome and matt black and also for RHD vehicles. Please choose the desired version. You get one complete set for your vehicle. IMPORTANT: We do not ship the right-hand drive / left-hand traffic versions to UK.UK customers please visit www.4x4overlander.com for the RHD/LHT headlights.

Robust main headlamp with integrated low beam, high beam & position light - stainless steel mounting included NOLDEN 7" Bi-LED main headlight kit with two headlamps with low-/high-beam and position light, including stainless steels bezels. Price advantage! Innovative 7" LED main headlight with proven reflector technology combines low- and hight-beam as well as position light in one lamp. Original dimensions and standard H4 socket mean that this is an easy to fit, durable replacement upgrade for any Land Rover Defender 90/110/130. Price for one lamp! Also fits (in some cases with additional apaptors or wiring looms) other vehicles, like Jeep Wrangler JK/TJ/CJ, various Toyota, Mercedes G etc. The integrated electronic driver / control unit makes for easy fitment. NOLDEN headlights are road legal, of course. They have ECE (also known as E-marked) and SAE approval and are available for either LHD (EU version) or RHD (UK version) vehicles. You can choose between light-crome and darker dark-crome looks. Compared to traditional halogen headlights LED lights offer many advantages: higher light output ("more light") more comfortable light ("white light"), closer to sunlight low energy consumption (32/39 W compared to 55/60 W low/high-beam) vibration and shock proof design (especially important for diesel cars or off-road use) never again (ca. 30.000 hrs lifetime) white road Illumination compatible with HID/Xenon one of the brightest LED high and low beam 7“ headlights available Many users of classical vehicles, especially off-road vehicles (Defender, Wrangler, G-Wagon) have been looking for modern headlights with classical looks. Up to now 7“ LED headlights had offered better illumination than halogen headlights, yet they didn't give optimum illumination or were of inferior design. In addition these were often retrofitting solutions that didn't meet OEM specifications. The new NCC 7“ Bi-LED headlight was especially tailored to meet the OEM requirements. All components, from the LED to the plug, are designed and produced accordingly making up a perfect overall system. The design of the 7“ Bi-LED headlights reminds more of a conventional halogen headlight that looks like the well-known classic design. The familiar appearance of the vehicle is thus not changed much and essentially still looks like “OE“. The illumination level of the new NCC 7“ Bi-LED headlight is equally good as that of a Xenon headlight. However, the new NOLDEN headlight system has the big advantage of a lower current consumption, which increases the life of the system significantly thus noticeably lowering the operating costs. In a normal case it can be expected that the life of the NCC 7“ Bi-LED headlight is much longer than that of the vehicle. The ligths don't require headlight adjustment or the headlight cleaning system of the Xenon system, retrofitting with the new NCC 7“ Bi-LED headlight is therefore much easier, faster and in the end less expensive than is the case with the Xenon headlights.  Technical details: dimensions in mm: 177 x 152 number of LED: 5 x Osram Automotive output (low-/high-beam): 32 W / 39 W voltage range: 9-32 V lumens calculated: 1.880 lm / 2.400 lm lumens measured: 1.550 lm / 1.700 lm fixing: PAR56 homologation: ECE, SAE front lens: UV resistent polycarbonate hard coated front lens housing: lightweight, rigid alumium housing waterproof: 480 h salt spray tested and fully water proof to IP6K9K NOLDEN Bi-LED main headlights are also suitable and approved for many European, Asian and American motorbikes. Also note our lower-price vehicle-dependent bundles for Jeep Wrangler JK, Mercedes G and Toyota LandCruiser HZJ. Please note that these lights have position lights. You can use the standard Defender position lights along with the headlight position lights, or you disconnect the position light of the NOLDEN lamps. You receive a complete fitting kit, including two lamps and fitting material for your vehicle. The Nolden LED lights are available in chrome, dark-chrome and matt black, the stainless steel bezels either in "stainless" or black powder coating. These lights are also available for RHD verhicles. Please choose the desired version. IMPORTANT: We do not ship the right-hand drive / left-hand traffic versions to UK.UK customers please visit www.4x4overlander.com for the RHD/LHT headlights.

The XPL Curved Lightbar is an extremely powerful installation solution for the slot of the standard radiator grille Installing work lamps, additional headlights or light bars on your vehicle is not too difficult – when you’re talking older pickups or classic Defenders, that is. Obviously, with newer cars like the New Defender one should be a lot more cautious before drilling holes or attaching brackets to the expensive exterior. Vision X Lighting specialize in custom solutions, combining top performance, sleek design and installation methods that minimize effort and actual alterations to your car.  The XPL Curved Lightbar by Vision X is an elegant and powerful LED solution for the lower opening in the standard grille of the New Defender. The array of individual 5 W CREE LEDs delivers a light beam of over 600 m – providing safety in all weather conditions, off-road or on-road, for work or sports. The XPL Curved lightbar also features backlighting that can be used as daytime running lights.  The installation is fairly simple and requires roughly 4 hrs. Both the grille’s plastic substructure and the lower opening need to be modified by sawing out specific areas. Detailed instructions, fastening materials and electric connections are included in the delivery. Mounting behind the radiator grille is also possible.  Specifications for XPL Curved Lightbar: LEDs: 5W per LED Housing material: aluminium Light colour temperature: 6000 Kelvin Voltage: 9-32V DC Current: 3.12A~8.96A@24V DC - 6.25A~17.92A@12V DC Vibration resistance: 21 Grms Lens material: Polycarbonate Smooth backlight Proprietary IRIS reflector technology Curved high power light bars Weatherproof Deutsch connector with plug-and-play wiring harness Certifications: CE, RoHS, IEC 62471, ECE R112 Thanks to our iris reflector technology and the unique curve of the bar, the XPL Curved series produces a wide spot beam pattern with a range of over 600 metres. Scope of delivery: Complete radiator grille set for New Defender with XPL-HC23 light bar, brackets and wiring harness including detailed installation instructions.

Complete set of AUTOTERM Air 2D parking heater for Defender The parking heater set AUTOTERM (Planar) 2D12 for the Land Rover Defender consists of all important components needed for the installation of a parking heater. Included in the delivery are the AUTOTERM 2D 12 Volt parking heater, our Nakatanenga parking heater console, the Nakatanenga mounting plate, a fuel tank extraction, a Webasto air outlet with 60 mm connection, 30 cm warm air pipe and a vibration damper.As a low-priced and powerful alternative to our Webasto parking heater kits, the AUTOTERM (=Planar) 2D parking heater is proving to be a real sales hit. This is partly due to the particularly compact dimensions, which allow installation even in small cars, vans, off-roader motorhomes, construction machinery, boats or in difficult installation situations. In the off-road / 4x4 sector, it is ideally suited for the "typical" off-road vehicles such as Land Rover Defender, Mercedes G or Jeep Wrangler JK.These are only a few of many reasons why we now offer the AUTOTERM (Planar) 2D 12 V parking heater in a clear and comprehensive complete set for the Land Rover Defender at an economical price. For both the Tdi/ Td5 and the Td4, we offer one set each with a perfectly matching accessory kit.You can select different front panel cut-outs for the parking heater console included in the scope of delivery. The associated connections are available in the classic cigarette lighter format (12 V) or as 5 V USB charging sockets for Apple iPhones, navigation devices, iPads and smartphones and are included in the scope of delivery.The parking heater can also be operated while driving.Running time: The AUTOTERM parking heater switches off automatically after 2 hours of operation. However, as soon as you press a button during operation, the parking heater continues to run indefinitely until it is switched off manually.Scope of delivery:- AUTOTERM 2D parking heater 12 volt incl. silencer, intake air hose, heat protection hose, tank intake pipe and corrugated exhaust pipe.- Optionally analogue control unit simple control (PU-5) with rotary control or digital control unit comfort control (PU-29) with time switch- Nakatanenga parking heater console incl. the selected connections- Nakatanenga mounting plate- Fuel filler cap- Webasto air outlet with 60 mm connection, rotatable- 30 cm warm air pipe (diameter: 60 mm)- Vibration damper- Fixing material (screws, nuts, clamps, shrink hose, cable ties)Technical data:- Fuel type: diesel- Heating capacity: max. 1.8 kW, min. 0.8 kW- Volume of heated air: max. 75 m³/h, min. 34 m³/h- Fuel consumption in operation: max. 0.24 l/h, min. 0.1 l/h- Power consumption in operation: max. 29 W, min. 10 W- Weight: 3 kg (independent heater)- Manual start/stop → On the Autoterm.cz site you will find a calculator for the correct dimensioning of the air heater,You can choose between two control elements:- Simple Control (PU-5) element with rotary control: The old PU-10 control element had a relatively inaccessible control surface. Therefore, the reliable control element with rotary control is now the new improved standard of the Planar parking heaters! With the rotary control, you can adjust the heating power of the parking heater and regulate the power of the ventilation in ventilation mode! The PU-5 control element with rotary control can also be purchased separately here.- The digital control element comfort control (PU-29) with timer has an OLED display and an understandable and clear interface.  Temperature, ventilation and power can be configured via the display and the various buttons. With the timer, you can easily set the start of the parking heater to a specific time. The digital control element with timer can also be purchased separately here.Setting options comfort control (PU-29):- Temperature and power (adjustable for the parking heater, the control panel and for an external heater).- Time and date - Operating language (English or Russian)Functions of the timer comfort control (PU-29):- Memory function: save the time so that the parking heater starts at this time every day - Configurable memory locations: Up to 3 different weekdays with different times can be set and saved. The AUTOTERM (=Planar) 2D12 is equipped with an altitude kit.This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heat output decreases proportionally to the amount of oxygen in the air. Roughly speaking, from 2,000 metres the loss of output per 500 m altitude is approx. 5%. Manufacturer tests up to 3,440 m were trouble-free. Up to 4,000 m no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not yet be tested at real altitude. Important:Especially when used at high altitude, the free travel of the fan is extremely important!Route the combustion air intake and exhaust extremely short and with low resistance - i.e. no kinks, no blockage or reduction. It should also be noted that operation beyond 3,000 m is still a technical compromise. Again, care should be taken to ensure that the combustion chamber is properly heated on a regular basis. The chamber must be burnt free of soot deposits. Soot deposits can also form on heaters that are permanently operated at the lowest setting. Therefore, the following still applies: No guarantee for sooty combustion chambers!In order to ensure the longevity of the heater, you should also free-burn it occasionally at low levels. The combustion chamber reaches full temperature after running at full load for about half an hour. Normally, no further maintenance is required. In case of extreme loads, e.g. during longer overnight stays at more than 4,000 m, the combustion chamber including the seal set should be cleaned if necessary. To heat your roof tent using your auxiliary heating system, we offer an installation service for a warm air duct through a ventilation plate. https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Cannon Race CR-7 - 70 Watt - SPOT BEAM DRIVING LIGHT Ultra-Bright 15.330 Raw Lumens Per Pair Broad Spot Beam Pattern with 458m of Distance and 60m. Wide SAE/DOT & ECE Approved Clear and Selective Yellow Lens Options Shatterproof Polycarbonate Lens The Cannon Race Series 7 LED (CR-7) delivers the highest performing spot beam to hit the market. The CR-7 utilizes a truly unique lens that performs as well as it looks. With a broad spot beam that reaches 458m long and 60m wide, the CR-7 outperforms and outshines the competition with ease.The CR-7 utilizes only top-binned 10W LEDs from CREE that allows the CR-7 to blasts a massive 15.330 lumens (pair) out of only a 114mm housing. Never let dust, fog or rain slow you down again. The selective yellow lens will allow your CR-7 to cut through any tough weather while maintaining maximum output.Virtually unbreakable, the CR-7 uses a powerful polycarbonate bezel that won't crack, fade or corrode like traditional aluminum bezels. Ready for the most extreme environments the CR-7's are submersible and watertight with a IP68/69K housing that is capable of withstanding any adventure you can throw at it. Features: LEDs: 7 x 10W Housing Material: aluminum Light Colour Temp: 5600 Kelvin Dimensions: 114/121/74mm Weight: 0.62 kg Voltage: 9-32V DC Amperage: 2.92A@24V DC - 5.84@12V DC Vibration Rating: 21.2 Grms Lens Material: Polycarbonate Certifications: CE, RoHS, ECE R112 Weatherproof Deutsch Connector

Nolden 7-inch Gen 2 Bi-LED Headlights: Illuminate the night and give your Defender the ultimate look! Now also available in All-Black = Stealth Edition! Do you love your Land Rover Defender, but the original headlights let you down in the dark or bad weather? Then it's time for an upgrade that not only provides brilliant illumination but also gives your off-road classic a modern and premium touch: the Nolden 7-inch Generation 2 Bi-LED Reflector Headlights! More light, more safety, more style – for your Defender: These high-end headlights are the result of German engineering and set standards in terms of light output, durability, and design. Say goodbye to dim halogen light and experience the road and terrain ahead in a whole new clarity. Brilliant Bi-LED Technology: Experience significantly brighter and more uniform illumination than with conventional headlights. The Bi-LED function combines low beam and high beam in one module, ensuring a seamless transition and impressive range. This means for you: You see obstacles earlier and drive safer – whether on a dark country road or in the deepest terrain. Plug & Play Installation: Developed as a direct replacement for your Defender's original 7-inch headlights. Installation is straightforward and requires no complex vehicle modifications. Extremely durable and maintenance-free: LED technology is not only more energy-efficient but also significantly more durable than halogen lamps. No more annoying bulb changes! These headlights are built to withstand the harsh conditions your Defender is exposed to. Modern look with a classic touch: The Nolden headlights blend perfectly with the Defender's iconic design while giving it a modern, high-quality appearance. The clear lens and thoughtful reflector design make them a real eye-catcher. (Depending on the chosen variant, e.g., in Chrome, you further enhance the premium look). With E-certification mark – road legal: Naturally, these premium headlights have the necessary E-certification, so you can drive legally and without concerns on public roads. Features at a glance: State-of-the-art Nolden LED low beam and high beam, LED daytime running light, and position light in fiber optic technology Significantly improved light output and visibility Perfect fit for Land Rover Defender (replaces original 7-inch headlights) Long lifespan and high energy efficiency Weather-resistant and robust Elegant design that enhances your Defender With E-certification mark for legal road use Treat your loyal companion to the light upgrade it deserves! With the Nolden 7-inch Generation 2 Bi-LED Headlights, you invest in safety, durability, and an unbeatable look. Turn night into day and enjoy every drive with perfect visibility! A few more details: Over 30,000 hours LED lifespan White road illumination, similar to Xenon H4 connectors for Plug & Play Standard 7” mounting (PAR56) Die-cast aluminum housing 480 h salt spray test Available in Chrome, Dark Chrome, Matte Black, and All-Black Approvals: ECE and EMC Technical Data: Low beam: 23 W High beam: 33 W Daytime running light: 8.5 W (fiber optic) Position light: 1.2 W (fiber optic) Dimensions: 177 mm LED Type: OSRAM Voltage: 12/24 V Weight: 880 g Tested: ECE, EMC Ventilation: Nitto Denko Air Cap Housing material: Diallyl Diglycol Carbonate (ADC) Lens material: Hardened PC (Polycarbonate) Temperature range: -40°C to +80°C Vehicle wiring: FLRY Connector: H4 for main headlight, Tyco/AMP Superseal for position light Reference number: 12.5 The Nolden LED headlights are available in Chrome, Dark Chrome, and Matte Black and are delivered with a cable set for position and daytime running lights. The set includes 2 headlights and 2 stainless steel mounting rings. Should you also want to replace the mounting kit during the headlight change, we have the following products for you: lighting/accessories/2735/headlight-mounting-kit lighting/accessories/2736/headlight-mounting-kit-for-land-rover-defender-with-stainless-steel-screws

Powerful light, easy installation – Vision-X GEN2 Cannon LED Bring light to unexplored territories with this headlamp! HYBRID ALUMINUM-POLYCARBONATE HOUSING The Light Cannon features a housing made of both aluminum for increased strength and polycarbonate for weight reduction. UNIVERSAL MOUNTING WITH ONE SCREW Designed for easy installation, the LED Light Cannon features a sturdy, single-screw universal mounting system. STANDARD FORM FACTOR The Light Cannon LED combines the benefits of LED lighting, including low power consumption and 50,000 hour life, with the standard form factor of a conventional HID or halogen lamp. Specifications: Range approx. 350m ECE R112 approval as a driving lamp LEDs: 1 x 40W Housing material: Hybrid Color temperature: 6.000 Kelvin dimensions: 121,6 / 134 / 93,7 mm Weight of one headlamp: 0.91 kg Voltage: 9-32 V DC Current rating: 1.67A@24V DC - 3.33A@12V DC Vibration Rating: 21.2 Grms Lens material: acrylic Certifications: CE, RoHS, IEC 62471 IP68 / IP69K

Increased brightness for long-distance and close-range illumination Especially when driving on country roads and unpaved paths, increased visibility can be an important safety factor. The LEDriving® Functional Series FX Gen 2 portfolio provides additional close-range and far-field illumination on dark roads. Even in poor visibility conditions or at dusk, the high-performance LEDs achieve a range of up to 635 metres and daylight conditions with a colour temperature of 6000 Kelvin. The auxiliary headlamps of the FX series impress with a special reflector design and not only provide a modern and appealing look, but also reduce glare for more visibility in road traffic. They can be used both as additional LED headlights and as powerful worklights. Both versions of the lights are fully ECE-compliant and therefore suitable for use in road traffic. In addition, OSRAM has developed a special mounting kit that is compatible with all auxiliary headlamps of the FX Gen 2 series for individual mounting. Versatile in use, they defy numerous environmental influences and are particularly light and at the same time robust and resistant thanks to high-quality materials such as the aluminium housing and the stable polycarbonate lens. Complete reverse polarity protection prevents damage due to overvoltage and contributes to a longer service life. The FX series auxiliary lights have been tested and validated in a DIN-certified environmental simulation laboratory for extreme external influences with regard to water, dust, shock, heat, cold and permanent vibration in accordance with the highest IP & IK protection classes IP6K8 & IP6K9K. Their variability gives the FX series a flexible range of applications. They can be fitted to cars, trucks, agricultural machinery, commercial vehicles, construction vehicles, caravans, off-road vehicles and quads. OSRAM provides a 5-year warranty on these products. Product details:OSRAM LEDriving® auxiliary headlamp Lightbar FX1250-CB SM GEN 2 | LEDDL134-CB SM Features: COMBO BEAM = Combined beam characteristics for both far-field and near-field illumination. Light beam of 630mLuminous flux: 11,000lm, rated power: 176W Cold white light with 6000K For 12V & 24V vehicles DTP04-2P, DTP06-2S connector, cable length: 1200mm Over- and undervoltage protection Single mount certified1) (2x ECE R149), ECE R10, ECE (Ref. 2x 50). Highest protection classes: IP6K8 & IP6K9K Robust and durable - shatterproof polycarbonate lens and die-cast aluminium housing with special black coating Efficient reflector design with 45 OSRAM high-power LEDs Side brackets included 5-year OSRAM guarantee 1) Product description: Outstanding illumination, performance, quality, form, durability and functionality. Maximum optical efficiency, effectiveness and homogeneous light distribution Coverage of far-field illumination Perfectly matched to individual requirements and needs for multivariant use Special reflector design for an attractive and modern appearance and reduced glare Robust and resistant - for a long service life Increased safety off-road and on-road ECE-compliant and approved for use in road traffic Fields of application: Cars, trucks, 4x4s, ATVs, agricultural vehicles, commercial vehicles, construction vehicles, quads, caravans, etc.1) Exact conditions at: www.osram.de/am-garantieNote: Single mount - no installation in pairs necessary, as two certified light sources are used.  

Door seal sets for Land Rover Defender - Perfect fit & robust for any terrain Whether replacing classic standard equipment or retrofitting for better sealing: Our selection of door seal sets for the Land Rover Defender offers the right solution for almost every model and year of manufacture. The high-quality seals (original or replica) ensure noticeably less wind noise, reliable protection against water and dust - particularly important for off-road driving or daily use in all weather conditions. Choose from different sets for driver and passenger doors, rear doors and side doors - all custom-fit, durable and easy to fit. More comfort. Less noise. Better sealing. Make your Defender fit for every adventure - with the right door seals from our range.    

NOLDEN LED high beam headlights, 70mm Set of 2, with E-mark, for installation   Technical data: Dimensions: 69.2x55 mm LED: 1x LED 13 W Fastening: 2x M6 Approval: ECE (E-mark) Material: Aluminum   Color: Black or chrome - please select.

Vision-X Expora spotlights Explora by Vision X LED auxiliary lights are the next generation of driving lights developed by Vision X for Explora, which are brighter, better and easier than ever to illuminate the surroundings. The Explora series combines Vision X high quality with efficient LED diodes – to deliver driving light at an unbeatable price!   With the Explora by Vision X LED driving lights, you no longer have to choose between a long or wide light pattern. Explora has unique reflectors, which provide a hybrid light beam, with both length and width, without any dark spots.   Explora by Vision X is an LED driving light with outstanding performance.   All models of Explora are E-marked, with Vision X E-boost. With E-boost, you can selectively increase the power of the LED diodes, for additional brightness. But even without E-boost, the Vision X Explora delivers a powerful light with length and width.   The Vision X Explora series is offered as both LED driving lights and LED light bars. What they all have in common is that they are incredibly durable – with lamp housings made of high-quality aluminum and lenses made of almost unbreakable polycarbonate. The driving lights and light bars all have brackets in super strong and durable composite to resist corrosion. Explora by Vision X is of course also dust and water resistant, with full IP68/IP69K rating. The entire Explora series meets the standards ECE R10, ECE R148 and ECE R149.   Last but not least, Explora by Vision X are incredibly easy to mount and install. These LED driving lights have a built-in smart control unit, so they only need to be connected to a power source and setup with clearly color-coded cables to the correct function.   Vision X Explora LED driving lights include wiring, nuts and brackets for installation. The driving lights also include a cover, which is easily mounted/removed when needed.   Properties: Unique reflectors that provide both width and length of the light E-marked driving lights with E-boost for extra effect Tasteful white or orange position light High durability with IP68/IP69K rating General data:  Estimated LED life: 50,000 hours Colour temperature: 5700K Light pattern: hybrid (length + width) Voltage: DC11-32V Lens: polycarbonate Lamp housing: aircraft aluminium Bracket: composite IP class: IP68/IP69K Vibration class: 6.9 gRMS Operating temperature: from -40°C to +60°C Certifications: ECE R10, ECE R148, ECE R149, CE, UKCA, RoHS, REACH E-marked: Yes Daten  7 Zoll 120W  9 Zoll 200W Watt: 120W 200W E-amplifier: 80W 130W Raw lumen: 8160 lm 13600 lm Effective lumen: 6000 lm 9700 lm LED: 24 x 5W 40 x 5W Light length: 386 m @ 1 Lux (460 m in pair) 480 m @ 1 Lux (700 m im in pair) Light width: 40 m @ 1 Lux (45 m in pair) 50 m @ 1 Lux (60 m in pair) Power consumption: 5,8A @ 13,5V  9,6A @ 13,5V Width: 186 mm  221 mm Height: 186 mm 225 mm Depth: 85 mm 102 mm Weight: 2 kg 3 kg  

Blower control for Land Rover Defender Fan and heater in classic Defenders are notoriously poor in performance and reliability – especially in northern latitudes, where cold winters and rainy days regularly impair comfort and safety in the cockpit. While Land Rover upgraded to an improved fan heater for the Td4 (MY 2007), all previous models can easily be retrofitted with an electronic control system. In contrast to the old analog fan heater, the new electronic control system allows for continuous adjustments. This ensures more efficient operation and therefore better ventilation, heating and dehumidification in the interior. Heating your vehicle’s interior can be achieved much quicker, as is demisting or de-icing of the windows. Additionally, the electronic control is much less prone to wear than the old mechanical solution using sliders and resistors, which are susceptible to shocks and vibrations. The retrofit kit includes the electronic control, a stepless slider and all the assembly parts for the connections. Installation instructions are included.  

Retrofittable seat heating Deluxe 12V The high-quality carbon seat heating system was developed for retrofitting in individual seats.You can switch off the heat supply of the carbon surface heating elements via a switch (0% power) or set it to one of 3 different heating modes: Mode 1: 25% power Mode 2: 50% power Mode 3: 75% power This three-stage system provides pleasant warmth within a few minutes. When a level is set, the heater heats up to 100% power in just two minutes and then adjusts down to the desired mode (25%, 50% or 75%). This allows the carbon panel heating elements to reach the desired heat output much more quickly. The button or switch indicates the current level via three LEDs integrated into the button. The button can easily be stuck horizontally or vertically anywhere. Three adjustable levels and remarkably fast temperature regulation make this seat heater unique. Differences between carbon panel heating elements and heating elements using stranded wire technology: The carbon panel heating elements have considerable advantages over the previously widely used heating elements with stranded wire technology. For example, only carbon heating elements can be adapted and trimmed during installation. With conventional stranded wire technology, a heating wire runs inside the heating element in the form of a wave. If this is damaged at any point, e.g. due to mechanical stress or overheating, the entire heating element fails. Parallel technology is used in the new carbon surface heating elements. Many independent carbon heating fibers run inside the heating element, ensuring its reliability. The heat distribution is much more homogeneous and therefore more pleasant with carbon panel heating elements. Scope of delivery: 2 carbon heating mats (one for the seat and one for the back) 1 wiring harness 1 button incl. necessary installation material and installation instructions   Technical data: Size of the heating mats: 645 x 250 mm (can be trimmed according to the installation instructions) Operating voltage: 9.6 V - 15 V Operating temperature range: -20 °C to +80 °C Power: up to 90W@13.8V Certification: ECE, EMC  

Stainless steel cover for air intake Military snow cover from stainless steel exclusively for Nakatanenga fits Land Rover Defender 90/110/130 (all model years) and reliably prevents the ingress of water, snow or dead foliage into the heating system. If independent vehicle heating is fitted, this will also always get enough clean air to work properly. Originally developed for the military Wolf-type Defenders, this military snow cover is also highly useful for civilian vehicles. The sturdy cover can be stepped on and is available for LHD and RHD vehicles. It can be fitted with or without chequer plate wingtop protection. Fitting simply means swapping the original cover and attaching the MSC with the six supplied stainless steel screws. Takes about 10 minutes. A new seal is supplied, too. Please choose desired type.

NOLDEN LED daytime running lights, 70mm Set of 2, with E-mark, for installation. Technical data:Dimensions: 69.2x55 mmLED: 1x LED 13 WFastening: 2x M6Approval: ECE (E-mark)Material: AluminumColor: Black or chrome - please select.

Jumper cable 6m length, max. 1200A The 6 metre long jumper cable offers quick help for weak 12 V or 24 V batteries. It is suitable for all petrol and diesel engines in cars and trucks.The copper mesh enables the cable to make optimum contact. The extra strong cast brass pliers prevent sparks and electric shocks thanks to their insulated handles. The scope of delivery includes a carrying bag for the jumper cable.Technical data:- Length: 2 x 6 m- Cable cross-section: 70 mm²- Max. load: 1,200 A (terminal)- Colour: red / black

Studs (Ø 9mm) for winter tyres If you have already planned a holiday abroad and regularly travel through snow, forest, rain or cold areas, these tyre studs are the perfect travel companions.  The studs can be fitted not only to tyres with existing stud holes, but also to other winter tyres. This is because the studs, thanks to their worm-shaped screw thread, can be easily attached and removed with the appropriate mounting tool and a standard cordless screwdriver, without leaving large visible tyre studs. You can decide for yourself how many spikes to put in the tyre and increase or decrease the number at any time afterwards if necessary. A spike can be conveniently removed from the anchorage and screwed back in later. Note: Tyre spikes are prohibited in Germany. Minimum tire tread: 9.5 mmMounting steps:1. position the head of the spike with the appropriate mounting tool.2. place the thread of the stud on the surface of the tyre3. push down & screw in with a cordless screwdriver while turning slowly4. screw in the spike only until the head touches the tyre surface.5. if the spike is unintentionally screwed in too far, leave it as it is - do not unscrew it again to try to get it into the correct position6. check the spikes every 1000km & correct if necessary7. with the help of the mounting tool and a cordless screwdriver the spikes can be grasped & removedTechnical data:Dimensions (Ø x length): 9.0 x 15.2 mmPenetration depth: 12.0 mmSpike diameter: 2.6 mmNote: Mounting tool for spikes 9mm Ø can be found HERE in the shop

Complete solution for clean diesel flow Powerful 100 W heating sleeve for fuel filters with a diameter between 73-95 mm. The sleeve has got crimped connectors and a wiring harness (incl. time relay and push-button). It prevents the gelling of fuel in colder temperatures and can be fitted to any vehicle with 12 V. Compared to customary sleeves this silicone heating sleeve is very flexible and can be fitted to many diesel filters. The sleeve guarantees ideal heating as it sits closely to the filter. Comes with powerful velcro strips for fitting. The waterproof wiring harness is fitted with a time relay with a push-button. The sleeve is switched on by push-button, it then heats for six minutes until it switches off automatically or for another six minutes if you press the button again. In cold climates your diesel fuel is prone to gelling as paraffin crystals form which turn the fuel flaky. As a result fuel flow through the filter stops and your engine loses power until it finally cuts out. Once the filter is blocked, it can only be freed by inducing heat. By emitting this heat and transferring it to the filter, our heating sleeve prevents the clogging of the filter element. The paraffin crystals are immediately dissolved by the induction of heat and the fuel can easily pass the filter again. You can purchase just the sleeve, without plugs, harness, relay and push-button here in our shop. Technical details:Maximal heat resistance of insulation: 300 °CMaximal operating temperature: 250 °CVoltage: 12 V, AC or DCOutput: 100 W Comes with:- silicone heating sleeve- wiring harness with time relay and push-button- 2 strong velcro straps

VIKING PRO XHP50 by ARMYTEK This light belongs in every hunter's backpack. Solid housing with 1" standard housing diameter, fits most underbarrel mounts. It is a powerful and robust tactical torch with all-round light pattern. Additional accessories, such as colour filters and cable remotes, have been designed to allow the torch to be used in a wide range of conditions. - Luminosity up to 1,800 OTF lumens.- Light range up to 370 m.- Up to 200 days runtime with a 18650 Li-Ion battery. Light and Optics Colour temperature: White Maximum output (LED lumen): 2,300 lm LED : XHP50 Optics : Smooth reflector (SMO) Maximum output (OTF lumens): 1,800 lm Light range, metre: 286 m Central field of light: 10 Lateral spread: 80° Operating modes: Number of modes: 9 Running time in highest light level: 1h Running time in lowest light level: 200 days Dimensions and weight Head diameter: 25.4 mm Case diameter: 41 mm Length: 154 mm Weight (without battery): 126 g Housing Max. Immersion depth: 50 m Max. Drop height: 30 m Working range: -25..+40 °C ElectronicsCompatibility with power sources: 1x18650 Li-Ion / 2x18350 Li-Ion / 2xR123 Li-Ion / 2xCR123A Protection against accidental switch-on Coloured battery level indicator Low charge indicator Scope of delivery: Holster with belt loop Carrying clip Hand strap Compat ring made of rubber Spare cap for switch 2 spare sealing rings Operating instructions Battery not included in delivery! (2x18350 Li-Ion available here in the shop) Application noteFor further application information please refer to the product data sheet Please note the legal information on batteries HERE. For certain types of batteries, we are legally obliged to charge a deposit.  

Radiator Cover for Standard Grille The Nakatanenga radiator cover helps your Defender’s engine reach its optimal operating temperature faster during the cold season – improving both engine efficiency and cabin heating performance.   This cover is designed to fit the standard radiator grille (including Heritage style) and all Nakatanenga aluminium grilles of all Land Rover Defender models, with or without air conditioning.   The cover is screwed onto the mounting points of the radiator cover.    For maximum versatility, the radiator cover can be used in three configurations: fully closed, half closed (top or bottom), or fully open.   Manufactured to U.S. military specifications (MIL-SPEC) and according to Nakatanenga’s own high standards. Includes FitKit.

Glow plug connector Land Rover Defender If the diesel has difficulty getting going when starting from cold, and if it nails and smokes particularly badly, this is often due to the glow plugs. Before replacing the plugs, however, you should first check the condition of the cables and plugs. Often, the problem is simply that cables and plugs are exposed through porous plastic sheathing and the electrical contacts are suffering. As a rule, the service life of the plugs far exceeds that of the cable and plug connections, because cables and plugs and their insulation are naturally much more exposed to mechanical and weather-related influences. With our glow plug connector repair kits, Defender with Td5 and Td4 2.4l engines can be very easily retrofitted in case of problems with cables or connectors. This is also recommended if the glow plug set is being replaced anyway. The advantage of the repair kit is that the next time a problem occurs, it is not necessary to replace the entire wiring harness at great expense; instead, it is sufficient to replace the plug and cable up to the crimp connection. This saves time and money and is also no problem for hobby screwdrivers. ATTENTION: Does NOT fit for Tdi and Td4 2,2l. Scope of delivery: 4 plugs

Snow chains for 4x4 - 235/85R16 Suitable for tire size: 235/85R16 TÜV/GS approved Scope of delivery: 2 chains