Shop by vehicle
Connection cable for reversing lights on Land Rover Defender (from 1998)
Convenient retrofitting Do you want to make reversing safer with your Landy? For all Defenders from 1998 onwards, our Y-cable adapter makes it very easy to install an additional reverse light. No extra cables or switches required. The two-pronged piggyback cable supplies both the original and the additional light with power. Once you shift into reverse, both lights will come on. All connection materials are included.
Prices incl. VAT;
Switch for ignition lock
Replacement switch for ignition lock The ignition lock switch can often cause problems. If it is defective, you will not be able to start the vehicle. Many people immediately replace the entire ignition switch, but if the ignition switch's turning mechanism is still working properly, it is much cheaper to replace the ignition switch located at the rear of the ignition switch. In this case, this item is the ideal replacement or repair part.
Prices incl. VAT;
Stainless Steel Bolt Kit for Front Bumper Defender 90/110/130
Fits all MY - TDi, TD5, TD4 2.4, TD4 2.2 with original-bumper Full bolt kit for one bumper - stainless steel bolts for Defender 90/110/130, comes with assembly paste. Do not use in conjunction with a winch or clevis pin bumper!
Prices incl. VAT;
Spacer / Spacers rear axle, 10mm, for Land Rover Defender
Rear axle spacers - 10 mm for Land Rover Defender These 10 mm spacers for the rear axle improve the track width and handling of your Land Rover Defender.Optionally suitable for Defender 90 or Defender 110/130, supplied in pairs. Registration is only possible by individual approval possible.Please select the appropriate wheelbase for your vehicle.
Prices incl. VAT;
Pilot bearing for all Defender TD4 models (MY 2007-2016)
Pilot bearing / Guide bearing for all Defender TD4 models (MY 2007-2016) We recommend replacing the pilot bearing when replacing the clutch.
Prices incl. VAT;
Dual Shock Mount, rear Axle
Bracket for double damper system - rear axle Maximum control, double damping: with this bracket for a double damper system on the rear axle, you can equip your vehicle for maximum loads and demanding off-road use. Supplied in pairs
Prices incl. VAT;
Wiper arm for Defender LHD, BJ 2001-2016
Land Rover Windscreen Wiper Arm Part for Defender 90/ 110/ 130 year of construction 2001-2016
Prices incl. VAT;
Stainless steel mounting set for floor panels in the front footwell, for Land Rover Defender
Front floor mounting set, stainless steel for Land Rover Defender Stainless steel fastening set for floor panels in the front footwell, for Land Rover Defender Fastening set includes the parts for driver and passenger side.Ideal for Nakatanenga storage compartment footwell - Land Rover Defender.
Prices incl. VAT;
Nakatanenga rear load bay sill for Land Rover Defender
Stainless steel bed strip for the Land Rover Defender 90 and 110 The loading area bar is made of corrosion-resistant stainless steel and replaces the corrosion-prone original loading area bar. Since the original screw heads occasionally tear off, the hole pattern is slightly offset. So new holes have to be drilled. The delivery includes stainless steel screws.
Prices incl. VAT;
Impact wrench socket 1/2", long, 27mm
Impact wrench socket 1/2", long, 27mm Power socket for changing wheels on the Land Rover Defender.
Prices incl. VAT;
Stainless Steel Brake Piston 46.0 x 30.8mm for various Land Rover Vehicles
High-quality stainless steel brake pistons for Land Rover vehicles - 46.0 x 30.8 mm Stainless steel brake pistons 46.0 x 30.8 mm, for various Land Rover vehicles, please measure which brake pistons you need! The brake pistons are made of stainless steel and therefore do not rust. These are quality products manufactured for us in the EU, which have a significantly higher material hardness than cheaper products from other suppliers. Scope of delivery: 1 piece
Prices incl. VAT;
Stainless Steel Brake Piston for Land Rover Defender - 41.2x28.4 mm
High-quality stainless steel brake pistons for Land Rover vehicles - 41.2 x 28.4 mm Stainless steel brake pistons 41.2 x 28.4 mm, for various Land Rover vehicles, please measure which brake pistons you need! The brake pistons are made of stainless steel and therefore no longer rust. These are quality products manufactured for us in the EU, which have a significantly higher material hardness than cheaper products from other suppliers. Scope of delivery: 1 piece
Prices incl. VAT;
Nakatanenga door net
Practical storage net for ideal storage of small items Easily create additional space for many small things that you would like to have within reach. The network is ideally suited e.g. for gloves, knives, flashlights, documents, papers and other useful utensils. You can attach the stowage net to the inner door lining so that everything stays in place. Dimensions: 17 cm x 37 cm Mounting material included Note: Mark the position of the net when the door is shot, that it is placed at the correct height and does not touch the seat box.
Prices incl. VAT;
Side wheel bearing Rover or P38 Differential
High-quality side bearing New side bearings are required when installing a differential lock (Detroit Locker or TrueTrac) if your vehicle has a P38 or Rover axle. Not required for the Salisbury axle. Please order this item twice. We obtain the side bearings from brand manufacturers such as Timken.
Prices incl. VAT;
Air scoop for Land Rover Defender
Air scoop, for Land Rover Defender 90/110/130 right or left side, for adhesive, rivet or screw mounting. Material: steel, black
Prices incl. VAT;
Metal sleeve for rubber mount for 1 piece Koni / RAID shock absorber top
Metal sleeve rubber mount for Koni Heavy Track RAID shock absorber 90-5375SP1 + 90-5471, top suitable for all years of construction! Scope of delivery: 1 piece
Prices incl. VAT;
Silencer / Spacer f. height compensation (P38 or Salisbury axle)
Silencer / Spacer f. height compensation (P38 or Salisbury axle) Description: the item can be used on the rear axle on 110s and 130s. optimal possibility for level compensation/ the height adjustment is 10 millimetres the ring consists of a zinc, phosphated metal ring with coil spring centring and vulcanised NR/ SBR rubber the rubberised surface of the ring reduces the transmission of vibration noise the washer is placed between the spring end and the spring plate, max. one washer per spring end is possible, i.e. max. two washers per spring, i.e. max. 20 mm height increase per spring is possible price per unit
Prices incl. VAT;
Rubber mount for 1 piece Koni / Trekfinder RAID shock absorber top
Rubber mount for Koni / Trekfinder RAID shock absorber top 90-5375SP1 + 90-5471 suitable for all years of construction! Scope of delivery: 1 piece
Prices incl. VAT;
LOF Clutches Flywheel Locking Tool for TD5
FLYWHEEL-LOCKING-TOOL This flywheel locking tool by LOF Clutches suits all Defender and Discovery TD5 models from 1998 – 2006, for both solid and dual mass flywheels. The tool locks the flywheel in place allowing the removal and torqueing of the TD5 flywheel bolts when changing the dual mass flywheel and the crank seal. A really handy bit of kit to keep in the toolbox. Includes 2 x M10 fixing bolts.
Prices incl. VAT;
Spacers for stabilizer bar front axle, for Defender 90/110/130 from TDI upwards
Spacers for front axle stabilizer The spacers are used to lower the stabilizer so that there is enough space for a cardan shaft with double joint. The spacers lower the stabilizer 1 cm. For Defender 90/110/130 from TDI. Dimensions per piece: 12x4x1 cm Scope of delivery:1 pair
Prices incl. VAT;
Screw set bonnet Land Rover Defender
Screw set bonnet Land Rover Defender optionally for Tdi /Td5 and for Td4 Defender bonnet screw set includes 2 front bumper screws, six stainless steel hinge screws with washers and nuts and two plastic hinge bushes The screws are supplied as Allen screws.
Prices incl. VAT;
LED Indicator relay 12V for Land Rover Defender
Flashing - LED 12V The four-pole relay for LED direction indicators prevents the indicators from flashing too quickly and allows the frequency of the indicators to be adjusted. It replaces the factory-fitted relay in the Land Rover Defender 90/110/130. To "activate" the LED indicator relay, the hazard warning lights must first be briefly activated after installation. Then use the rotary control to adjust the relay so that the trailer coupling indicator light goes out in left/right mode.
Prices incl. VAT;
Fitting Kit Headlight for Land Rover Defender, stainless steel
Fitting Kit Headlight for Land Rover Defender, stainless steel Fitting kit for one headlight for Land Rover Defender, consisting of stainless steel screws and anti-seize paste.
Prices incl. VAT;
Castor Correction Wedges 3 °
Correction wedges 3° for leaf spring axles - for optimising the axle geometry If you raise your car’s suspension or exchange your original shocks, most of the time axle or wheel geometry, i.e. caster or camber angles, will get out of alignment. To correct aberrations on axles with leaf springs, especially our 3-leaf parabolic springs for the 88” rear axle Land Rover Series II, IIA und III, we are now carrying these caster correction wedges. The wedges provide 3° correction and have a 13 mm pin opening.
Prices incl. VAT;
Seal Vent Flap Land Rover Series III and early Defender 90/110/130
High-quality seal for the ventilation flaps on Land Rover Series III and Land Rover Defender up to and including model year 2006 In contrast to the original parts made of foam rubber, this is a fully-fledged sealing material. The seals give way slightly over time. You can (re)glue them in with a PU adhesive. Scope of delivery: 1 piece
Prices incl. VAT;
▷ Repair kit for Defender tailgate hinges - available here!
Repair kit for tailgate hinges screwed version1 set, see pictureOnly suitable for hinges with screwed bolts.Does not fit hinges with pressed bolts.
Prices incl. VAT;
LED festoon bulb, 39mm, for Land Rover Defender 90/110/130
Bright, white light with minimal power consumption and a long service life - LED soffits make it possible! LED soffits for the Defender - Simple. Fast. Impressive. Do you love your Defender, but the interior lighting leaves a lot to be desired? With our new LED soffit, you can bring the latest lighting technology into your vehicle - and it's plug & play! The durable and vibration-resistant 39 mm LED soffit is a direct replacement for the bulb in the standard interior light(s) in the Land Rover Defender 90/110/130. Why an LED soffit? Our LED soffit has been designed to give you brighter, more efficient and stylish lighting. It's a perfect upgrade. Plug&Play - It couldn't be easier! No long installations, no tangled cables, no specialist knowledge required! Our LED soffit can be installed in just a few minutes. Simply remove the existing interior light, plug in the LED soffit and you're done. The plug & play system makes it possible - even for beginners. Advantages at a glance: Bright, uniform illumination: Thanks to state-of-the-art LED technology, the base centre provides pleasant, bright lighting in the interior.Daylight white; light colour 6000 KelvinVoltage: 12 V Energy-efficient: LEDs consume less power than conventional light bulbs, saving your Defender's battery. Durable: LEDs have a significantly longer service life and are resistant to vibrations and shocks. Easy installation: No workshop required - you can install the Soffitte yourself in just a few minutes.Ready to install - plug & play Who is the LED soffit suitable for? Our LED soffit is the perfect solution for all Defender fans. It is suitable for the Defender 90 as well as for the Defender 110 and 130. Please observe the polarity when installing! Scope of delivery: 1 piece
Prices incl. VAT;
Control panel PROFI 2 for Cubbybox
Switchboard PROFI 2 for Cubbybox New control panel Cubbybox Land Rover Defender made of high quality aluminium with 3 Profi switches with green LED lighting, circuit breaker and voltmeter for independent testing of 2 different batteries, cigarette lighter with socket, rubber cover and fuse, 190 x 132 mm.
Prices incl. VAT;
Nakatanenga rim reinforcement for splash guard holder
Nakatanenga rim reinforcement for splash guard holder Edge reinforcement for splash guard holder, for Land Rover Defender 110.Dimensions of a single edge reinforcement: 10 x 2.3 cm. Supplied in pairs.
Prices incl. VAT;
Sun visor organizer Version 2.0
Where to go with all the little things in the vehicle? There is more storage space here! With this sun visor organizer, you create additional storage space for many small things that are otherwise unfounded in your vehicle. The usability of the sun visor and the field of vision of the driver are not limited. Important utensils are always directly accessible with this sun visor organizer:Super practical e.g. for belt cutters, glasses, sunglasses, ballpoint pens, notepad, small flashlight, multitool etc. The organizer is easily attached with Velcro straps and can be just as easily and quickly removed. Integrated zipped pocket and MOLLE loops. Width of the organizer is 290 mm. Material: 100% nylon The Nakatanenga sun visor organizer is available in different colors: green-brown coyote sand Universally applicable for all vehicles! You can find the Nakatanenga card holder here. You can find the matching mirror for the organizer here.
Prices incl. VAT;
Housing for remote control Land Rover Defender
Only the most hardened purists would welcome a return to the times before central locking. Let’s be honest, we’ve all become too spoiled. A Landy with central locking is better than one without. Our replacement case for the key fob is meant to replace the original one when the the buttons are faulty or the shell too worn out from use. Simply install the electronics from the original remote in the new key fob case and attach to your key ring. New programming is not required. Suitable for Land Rover Defender with separate remote control, incl battery CR2032. Except for remote controls with the following form:
Prices incl. VAT;
Cup holder for Cubbybox
Replacement cup holder for Cubby Box. If your cup holder of your Cubby Box breaks, the cup holder is available as a spare part from us. 0.5 l drinks bottles and coffee cups fit perfectly into the practical cup holder. Also ideal for self-made center consoles.
Prices incl. VAT;