Power distribution box with fuse holder from BlueSea Compact size BlueSea blade fuse block and power distribution for either six or up to twelve seperately fused circuits for up to 30 Amps per electronic installation and currencies up to 32 volts. Fitting a variety of cars with 6 V up to 24 V supply systems. These fuse boxes also provide a common negative bus to minimize bad earth problems. New version offers two separate circuits, thus allowing e.g. 6 installation with permanent life feed and 6 with ignition life feed. This fuse box can be the starting point for well laid-out and safe vehicle electrics and should be fitted from early on when starting fitting additional appliances and electical installations. The box itself should be fused - not more than 30 cm away from the battery with a maximum of 125 A - for which we recommend our fuse carrier (up to 200 A) from the same supplier with the suitable 125 A MIDI strip fuse. Comes with: fuse box for either 6 or 12 circuits clear plastic cover with recessed placeholder for lables two slots for spare blade fuses no fuses supplied Technical details: Modell SHMA-6 SHMA-12 SHMA-6+6 number of circuits max. 6 max. 12 max. 6+6 placeholder for spare fuses 2 2 2 dimensions 125x85x39 mm 165x85x39 mm 165x85x39 mm weight 250 Gramm 350 Gramm 350 Gramm max. per circuit max. 30 A max. 30 A max. 30 A max. overall max. 100 A max. 100 A max. 100 A max. voltage max. 32 V max. 32 V max. 32 V Please choose number of circuits.

Side Lockers Externally accessible storage space is standard in Land Rover emergency or service vehicles. And for good reasons. Firstly, unused hollow spaces within the body offer additional stowage and secondly, items that shouldn’t be stored inside the car due to access, hygiene or health reasons can be kept separately. Especially when the vehicle has been modified into a camper van or the load space has to be kept clean for humans and animals, it is a good idea to keep certain items in exterior storage. This includes oily tools, wet and dirty clothes or smelly and chemically hazardous items like jerry can spout, funnels or fuel-soaked rags. Camping fans particularly like to store gas cookers, cartridges and cooking accessories in the side locker. Using the lid as a table, your morning coffee tastes best besides your vehicle. We have completely overhauled the side locker and managed to improve some of the key features significantly. So, if you haven’t cut a hole in the rear left of your Defender yet (or had it done for you*), it’s now time to do so. And if you already have our old side locker installed, you can easily upgrade to the new version. Dimensions and mounting holes are fully compatible so that the upgrade can be installed in no time. What’s new? The box is now welded all around and the construction has been designed to meet the requirements of IP67. This has greatly improved the stainless steel locker’s robustness and waterproofing. We also added a new compression key lock with IP66 certification. The lock’s clamp can be adjusted so that the lid will stay permanently tight and rattle-free. The lid’s hinges are mounted at the bottom and it is held at a 90° angle by small chains on either side, forming a small tray or table. The side locker is custom-made for Defender 110s. The five door station wagon will take the storage box behind the rear left wheel arch, the three door hard top alternatively offers installation in front of the wheel arch. Alternatively, this middle position in the hard top Landy can also take our bigger locker with even more stowage space. The new side storage locker can also be installed in all other camper vans and expedition vehicles which offer suitable space in the body. As always, we are happy to assist with any questions you have. Water and dust proof! Suitable for all Land Rover Defenders 110 from 1992 (Tdi, Td5, Td4) Station Wagon and Hard Top Delivery includes 2 keys and all required fixings. Dimensions: 355 x 270 x 340 mm Material: stainless steel, the lid is powder coated in black RAL9005 matte https://www.nakatanenga.de/media/pdf/74/df/0c/Merkblatt-Edelstahl-und-Rost.pdf  Installation advice: - Defender 110 station wagon: behind rear left wheel arch- 110 hard top version: also in front of the rear left wheel arch- * Cutting into your vehicle’s body takes some experience and the tasks can vary immensely which each vehicle, especially if you have to remove struts, panels or checker plate. If you’re uncertain or don’t have the right tools, we highly recommend leaving the cutting of the opening to the professionals. Installing the box itself is DIY level though.

LED signal lamps for Land Rover Defender, smoke grey The advantages of LEDs are well known: low power consumption, strong light output, vibration resistance and a long lifetime. In this smoke grey signal lamp set for the Land Rover Defender (Series III, Defender 90, Defender 110, Defender 130) the following LEDs are included: The standard-set with 8 bulbs contains: 2x front indicatior ligths 2x front position lights, either with or without day-driving light 2x rear indicators 2x brake/rear lights adjustable indicator relay The set with 9 bulbs additionally (aditionally to the standard-set) contains:  1x tailgate break light The set with 10 bulbs additionally (aditionally to the standard-set) contain:  → 1x fog light and 1x reverse light→ OR 2x wing side indicators The set with 11 bulbs additionally (aditionally to the standard-set) contain:  → 1x fog light, 1x reverse light and 1x tailgate break light→ OR 2x wing side indicators The set with 12 bulbs additionally (aditionally to the standard-set) contains:→ 1x fog light and 1x reverse light and 2x wing side indicators The set with 13 bulbs additionally (aditionally to the standard-set) contains:→ 1x fog light and 1x reverse light, 2x wing side indicators and 1x tailgate break light Note that indicators must be orange by law. All bulbs come with E-approval so that they can be fitted without further TUV recording. All bulbs come with correct plugs for simple replacement for vehicles from MY 1998 (TD5 und TD4). Fittings are supplied and also an adjustable indicator relay that even allows to adjust indicator speed. Older vehicles can be retrofitted after removing the plug. This requires soldering. If the lamps on the existing vehicle are square at the rear, you need 1x AMR3850 mounting base per lamp to mount the new round reversing lights. As a rule, the original drill holes can be used. This signal lights kit is the ideal addition to our 7" Bi-LED main headlights, the LED license plate light and any additional LED spotlights - this brings the Land Rover Defender into the 21st century light-wise! Please note: The screws must not be over tightened (only hand-tight!), Otherwise the plastic housing may crack. These cracks could allow water to penetrate into the generally watertight luminaires. Use only a screwdriver and NO cordless screwdriver!