Heavy Duty Clutch Kit for Land Rover Defender TD5 The clutch has to transmit enormous forces, especially when shifting gears under higher loads, e.g. in trailer operation or in vehicles with increased performance. A sometimes occurring problem in connection with the original clutch of the Defender is the penetration of oil from the engine or the gearbox into the clutch bell. This oil is absorbed by the porous friction linings and repeatedly comes into contact with the friction lining surface during driving due to the frictional heat generated. As a result of the reduced frictional engagement, the friction linings generate more heat and glaze. The heat is a measure of the converted energy that is no longer available to the drive!The organic lining used in this clutch cannot absorb oil and therefore cannot vitrify. It convinces with specially adjusted friction modifiers with a soft response behaviour and enables a 100% frictional connection. It goes without saying that the pads are asbestos-free, lead-free and free of other toxic heavy metals and heavy metal compounds.Note: We also recommend replacing the old clutch slave cylinder & clutch master cylinder -> Clutch slave cylinder / clutch master cylinderComplete set consisting of automatic clutch, friction disc and release bearing.

Heavy Duty Clutch Kit for Land Rover Defender TD4 Especially with switching operations under higher load, such. in trailer operation or in performance-enhanced vehicles, enormous forces must be transmitted by the clutch. A common problem with the Defender's original clutch is the failure of the insufficiently sized torsion springs. The torsion springs, which are specially adapted to the Defender Td4, eliminate the familiar problems with clattering or jamming couplings. Another, but less common problem is the ingress of oil from the engine or transmission into the clutch bell. This oil is absorbed by the porous friction linings and occurs during driving by the resulting frictional heat repeatedly to the friction lining. Due to the reduced traction it comes in the episode to a higher heat development and vitrification of the coverings. The heat is a measure of the converted energy that is no longer available to the drive!The organic coating used in this coupling can not absorb oil and therefore does not vitrify. It convinces with specially adapted friction modifiers with a soft response and enables a 100% adhesion. Of course, the pads are asbestos- and lead-free, free of other toxic heavy metals and heavy metal compounds. Complete set consisting of automatic clutch, friction disc and release bearing. Clutch kit with clutch slave cylinder for Defender TD4 from year of construction 2007-2016 We recommend replacing the pilot bearing when replacing the coupling.Please note:  Before installing the clutch, the following dimension must be measured on the flywheel If the dimension is 25.4 mm, the clutch can be installed. If the measurement is 22.2 mm, a Ford flywheel is installed. The clutch is not compatible with this and will malfunction sooner or later. If a Ford flywheel with a measurement of 22.2 mm is installed, you will also need the following Land Rover flywheel.

Clutch slave cylinder for Defender TD4 You can choose between a clutch slave cylinder for Defender TD4 up to chassis number 8A999999 and a clutch slave cylinder for Defender TD4 from chassis number 9A000001.ATTENTION: Occasionally, different clutch release bearings may have been fitted by previous owners. If you are not sure which clutch slave cylinder you need for your release bearing, please order the other clutch slave cylinder. You can then test both and return the non-fitting part to us within 4 weeks in its original packaging.

saving bundle: Heavy Duty clutch kit incl. Improved MT82 intermediate shaft for TD4 saving bundle consisting of automatic clutch, friction disc, release bearing, matching clutch slave cylinder and a reinforced intermediate shaft MT82 transmission. For TD4 built in 2007-2016 Information about the clutch automat with friction disc, release bearing and clutch slave cylinderEspecially with switching operations under higher load, such in trailer operation or in performance-enhanced vehicles, enormous forces must be transmitted by the clutch. A common problem with the Defender's original clutch is the failure of the insufficiently sized torsion springs. The torsion springs, specially adapted to the Defender Td4, eliminate the familiar problems of clattering or jamming clutches. Another, but less common, problem is the ingress of oil from the engine or transmission into the clutch bell. This oil is absorbed by the porous friction linings and occurs during driving by the resulting frictional heat repeatedly to the friction lining. Due to the reduced traction it comes in the episode to a higher heat development and vitrification of the coverings. The heat is a measure of the converted energy that is no longer available to the drive! The organic coating used in this coupling can not absorb oil and therefore does not vitrify. It convinces with specially adapted friction modifiers with a soft response and enables a 100% adhesion. Of course, the pads are asbestos- and lead-free, free of other toxic heavy metals and heavy metal compounds. Information on the reinforced intermediate shaft for MT82 transmissions.Improved intermediate shaft for MT82 transmission in Land Rover Defender TD4 / TDCi / Puma 2.4 / 2.2 Known problem: The intermediate shaft of the TD4 / TDCi / Puma 2.4 / 2.2 models is not greased and is not supplied with oil. The connection of the two-piece intermediate shaft wears after prolonged use, since the shaft with outer ring gear has direct contact with the shaft with inner ring gear. In the worst case, this wear ensures that the sprocket shears off and the vehicle thus stops. A regular lubrication of the sprocket helps, but is in the long run very cumbersome Our solution: The improved intermediate shaft is supplied with the oil of the gearbox and thus prevents the wear of the shafts. Easy and uncomplicated! We recommend replacing the pilot bearing when replacing the coupling. Please note:  Before installing the clutch, the dimension of the following step must be measured on the flywheelIf the dimension is 25.4 mm, the clutch can be installed.If the measurement is 22.2 mm, a Ford flywheel is installed. The clutch is not compatible with this and will malfunction sooner or later.If a Ford flywheel with a measurement of 22.2 mm is installed, you will also need the following Land Rover flywheel.

Clutch Slave Cylinder for LR Land Rover Defender and Discovery 2 Td5/TDI R380 for all 300TDI and TD5 engines in all Defenders and Discovery 2 with a manual transmission (R380)