Alloy rim Diewe Amaro 9x20" ET37 5x120 for New Defender LE

Wheel spacers TREKFINDER for LAND ROVER New Defender LE 90/110 ATTENTION: NOT FOR STEEL RIMS - USE ONLY FOR ALUMINIUM RIMS Material made of aluminium, black, hard anodised SCOPE OF DELIVERY: Widening per axle +60 mm / +50 mm / +44 mm / 40 mm millimetres 2 pieces wheel spacers incl. mounting material 1 piece TÜV® parts certificate Assembly instructions Care and cleaning instructions Scope of delivery for 1 axle AREA OF APPLICATION: Vehicle manufacturer: Jaguar Landrover (GB) / 1590 Vehicle type: LE Trade name: Defender ABE-EG number: - e5*2007/46*0092* . . - e5*2007/46*0125* . . The use of wheel spacers is permitted for the following wheel sizes/rims/references: NOTES and REQUIREMENTS: A1) The screw-in length of all fastening elements must be at least 7.5 turns (M14x1.5).Ensure that the stud bolts are of sufficient length.The screwed-on spacer rings are fastened to the vehicle with the fastening elements supplied by the manufacturer of the spacer rings (taper collar wheel nuts).The standard wheels are fastened with the standard fastening elements.It is particularly important to ensure that the length of the stud bolts in the spacer rings (free thread length above the wheel contact surface) corresponds to the length of the standard stud bolts, in this case approx. 28 mm (VA/HA). H1)The usability of snow chains was not checked. H2)There are no technical objections to the use of standard or other wheel/tyre combinations up to the above (limit) wheel/tyre combinations in conjunction with the described spacer rings if the following conditions are met:Separate suitable certificates for the wheel/tyre combinations are available and the conditions listed therein are complied with. In addition, the above-mentioned conditions must be observed and applied if necessary.If other wheel/tyre combinations are used, their suitability (clearance, handling, etc.) must be checked or proven separately.Use of the spacer rings on the front and rear axle or only on the rear axle.There are no technical objections to the additional use of tested chassis lowering or raising (with parts certificate or ABE).In the case of chassis lowering with non-standard end stops, the suitability of the conversion must be checked or proven separately.Use of the spacer rings on the front and rear axle or only on the rear axle. Furthermore, it is possible to combine spacer rings with different widths on the front and rear axle. For example:Axle 1 spacer rings with 20 mm width and axle 2 spacer rings with 30 mm width.Always use wider spacer rings on axle 2 than on axle 1. H3)All fastening elements must be checked with a suitable torque spanner after approx. 100 km of driving. H4)The instructions in the manufacturer's installation manual for the spacer rings must be observed.The installation of spacer rings is not permitted if the diameter of the spacer rings is smaller than the diameter of the wheel contact surface of the wheels.The spacer rings are not permitted in conjunction with steel wheels. H5)With regard to the track width change of more than + 2%, a laboratory report on the sufficient operational stability is available and deposited ( you do not need to bother ):No. 21-00075-AS-MUC-00 / 10.08.2021 / TÜV SÜD Auto Service GmbH. H6)The bolted 20 to 30 mm wide spacer rings are tested up to a wheel load of 1000 kg. H7)Also permissible with standard wheel/tyre combinations with tyre code LT. H8)Only in conjunction with LM wheels with corresponding "casting pockets" which can accommodate standard stud bolts or nut heads protruding beyond the wheel contact surface.The standard stud bolts may have to be shortened.The minimum screw-in length of all fastening elements of 7.5 turns must be maintained.  

Seat cover for Land Rover New Defender 110/130, driver and passenger side This isn’t off-the-peg, this is made to measure! If you’re looking for seat covers for the New Defender – the front seats to be precise – look no further than our seat protectors made from durable, and easy-to-clean 1000D Nylon 6.6. The seat covers were developed by us in our own tailor's workshop  – guaranteeing highest functionality and best workmanship. To ensure maximum comfort and compatibility with the climate technologies in your seats, the covers feature breathable mesh fabric on the actual sitting surface. And even though it is mesh, it will still protect the seat from dirt and moisture. To achieve a perfect fit, the one-piece cover is tightly tailored and does not require zippers or similar. Simply pull it over the seat, Velcro the top part underneath the headrest and close the sturdy straps and buckles on the underside. Additionally, a mesh pocket with a rubber foam piece inside is wedged into the gap between backrest and seat surface to prevent the cover from sliding. On the sides, openings in the cover allow easy access to the headrest controls. As with all our textile products, we always aim to add additional storage space. Generously sized MOLLE patches on the sides as well as large pockets in the rear of the backrest and the front rail of the seat make it very easy to store everyday items and small pieces of equipment temporarily or permanently. Our seat protectors come in the colors Coyote or black with uni-colored mesh insets. Material: Nylon, PU-coated Not suitable for New Defender 90 or the version with a 4-way adjustable headrest! The seat in the 90 design has a folding mechanism on the side to tilt the seat. These seat covers have NO! Recess for this lever.  This article was designed in our in-house tailor shop. A dedicated team and short distances allow for continuous quality control and further development of our textile products. And if you already have a tailor's workshop in house, then it is easy to also accept customer change requests, special designs, suggestions and proposals for improvement at short notice and to implement them as far as possible. Mail or phone call is all it takes! And by the way: At Nakatanenga we only use materials with 100% nylon PU coating for all textile articles. Unlike PVC, nylon PU (polyurethane) is free of harmful phthalate-based plasticisers. Until recently, low-molecular phthalates were the most common plasticisers for plastics of all kinds and are even used in food and cosmetics. However, they accumulate in the environment and are suspected of acting like endogenous hormones due to their molecular nature. This is highly questionable from a toxicological point of view and is considered to be a trigger for various diseases, including cancer. For Nakatanenga, it is therefore a matter of course to use only ecologically and health-safe alternatives such as nylon PU for the coating of textile products.

Bumper protection in different colours What’s worse than a scratch on your car? Clearly that very first scratch! How annoying is it when you spot one on a pristine new vehicle? Even when 4x4s generally wear their scars with pride, most signs of heavy usage aren’t necessary, they’re frustrating and also depreciate the value of your vehicle. One of the first areas to show signs of wear and tear – especially with off-road vehicles – is usually the cargo area. But if your 4x4 is a New Defender, would you really want to see a worn and scratched rear bumper? Immediate and long-lasting prevention of wear marks on your New Defender’s rear bumper can be achieved with our designated paint protection film. This high-performance product by industry leader 3M protects your New Defender’s rear bumper from scratches and abrasion even when your loading area is constantly in use for work or sports. And don’t forget the damage a dog’s claws can do to the paint when you carry them regularly in a dog box in the back. Due to its multi-layer structure, the 3M wrap also protects the bumper from chipping caused by the impact of small stones or dropped objects. Installing the paint protection film is really easy. Everything you need is included: cleaning cloth, adhesion promoter wipe, squeegee and detailed instructions. If you’ve never done this before: don’t worry. The protective wrap can be positioned exactly as you need it, but if you have to readjust the position a few millimeters that’s no problem either. Simply slide the film into place. It only starts to adhere once you apply pressure with the squeegee. The protective wrap is available in black, matt black, anthracite grey or silver, making it a perfect visual match for any New Defender color scheme. Comes in one complete „no worries“ kit: foil, squeegee, cleaner, primer. Available in Black, Matt Black, Anthracite, Silver or Matt Transparent*, the protective film perfectly matches the look of the new Defender, regardless of its paint finish or colour scheme. Please note:The transparent version differs from the other versions in terms of price and workmanship, as it uses a specially developed, UV-stabilised film. This film is specifically designed to minimise material yellowing caused by UV radiation and ensure long-term visual stability.The transparent film MUST be applied wet! For professional application, we provide detailed installation instructions and the necessary processing materials. Instructions for wet application: Fill a spray bottle with water and 1–2 drops of washing-up liquid (or mounting/application solution). Remove coarse dirt from the loading sill with a damp cloth and then clean thoroughly with the enclosed cleaning cloth – the surface must be clean and dust-free. Spray the loading sill evenly. Remove the protective film from the film and also spray the adhesive side lightly (so that it does not stick immediately). Apply the film and align it carefully. The moisture allows it to be moved around. Squeegee out the water, working from the centre outwards. Apply even pressure to remove the water and air bubbles. Remove any excess liquid with a cloth. The film is fixed after squeegeeing, but only reaches its final adhesion after 24–48 hours.   During this time: Do not wash, do not use a high-pressure cleaner. Keep as dry as possible and avoid mechanical stress.    

The new Defender combines modern technology with proven off-road capability. Good air circulation as if the windows were slightly open, but without the risk of rainwater or theft? Plus effective protection against insects? That's what our ventilation panels with mosquito nets offer, made to fit the New Defender perfectly from high-quality aluminum—no wobbly universal parts. Supplied in pairs and powder-coated in black, they complement the modern design discreetly and sensibly, especially when camping or on expeditions. Installation is straightforward: roll down the window, insert the ventilation panel, close the window again – and it sits securely and rattle-free. ⚠️ Important note: Children and animals must never be left in the vehicle at high temperatures, even with the ventilation panels in place. Suitable for Defenders built from 2020 onwards. Length: 550 mm