This full stainless steel spare wheel carrier for Defender SW/HT is the successor to our Defender spare wheel carrier RRHNAHI sold by the hundreds. It is available in two colours. The Defender rear door suffers from the heavy weight of the large spare wheel. Depending on use, after about five years or 50.000 kms the first cracks in the rear door frame appear. There are two solutions for this well-known problem: either move the spare wheel to the bonnet (see our bonnet spare wheel mount for that, not possible for post MY 2007 Defenders) or you fit our rear door spare wheel carrier. It takes off the complete weight from the rear door and opens along with the door. The carrier is fitted to the rear crossmember, a plate is mounted to the existing holes in the door, which is then attached to the carrier with two cranked stainless steel pivots. This carrier has been tested extensively, among others on the "Grand Erg" rallye and combines easy fitting with high toughness and exeptional usability. Available for all Defender models with rear door (Station and Hardtop). Improved design in 2014 and full stainless steel fabrication. The bearing is maintenance free, the complete carrier rustproof and can be completely revised it necessary. It's compatible with Land Rover rear step / bumper with towbar. Fitting is possible on a DIY basis. We also offer fitting service. If you also 'buy' the fitting charge we will contact you for an appointment. The spare wheel carrier opens together with the rear door, no further unlocking necessary. For vehicles with a tailgate (Pickup, not HCPU) we offer a separate sparewheel carrier: NARRTDEF-STPU THe carrier is available in stainless steel or black powder coating for vehicles up to MY until 2016 Full stainless steel spare wheel carrier for Defender SW/HT. Fits to rear crossmember. Door is completely unloaded, two colours available. The spare wheel carrier is designed and tested for a total weight (spare wheel and possibly other accessories) of 120 kg. The spare wheel carrier for years of construction up to 2001 is supplied with a suitable mounting plate (no picture available).

Nakatanenga Spare Wheel Carrier Defender Pickup / Softtop, until MY2016   To preserve the original Defender look and to make room on the inside we adjusted our classic spare wheel carrier for the pic-up version of the defender (Attention: there is a separate version available for the classic hardtop). The carrier is independent from the rear gate, we eliminated any noise and made it from stainless steel. The carrier is thoroughly tested, e.g. on the "Grand Erg" Rally. It was designed to ease the installation while guaranteeing usability and resilience. In 2014 we further improved the design and started manufacturing entirely from stainless steel. The bearing does not require service, the entire carrier is corrosion resistant and can be removed just as easily as installed if needed. This wheel mount is compatible with the additional step and with the hitch from Land Rover, as well as our rear bumpers The carrier can easily be mounted yourself alternatively we also offer an installation service. Simply add the service flat rate to your cart and we'll contact you to confirm your appointment.   The carrier does not swing open by itself, secondary unlocking to the gate is necessary. The carrier is also available in black or can be painted matching to your vehicle.   Attention:   This mount would also work on a Stationwagon. BUT: the carrier always needs to be opened separately from the outside and does not stay opened (on the pickup this is secured by the gate). It can not be opened from the inside, hence using the third row of seats would no longer be possible, since there is no emergency exit. This emergency exit is also required for campers.   The spare wheel carrier is designed and tested for a total weight (spare wheel and possibly other accessories) of 120 kg.   Suitable for vehicles up to MY2016

Nakatanenga RSpare wheel retaining plate stainless steel The stainless steel mounting plate is designed for DIY projects. It enables a Land Rover Defender wheel to be mounted on a flat surface, e.g. on a roof rack, a loading area or in the interior. The screw-in bolts/threaded rods have standard threads M16x2. The tire is fastened using the washers and nuts supplied. The screw-in bolts are 190 mm long. The size of the base plate is 200 mm x 200 mm. The plate alone, without accessories, is NOT suitable for mounting the spare wheel on the hood of the Defender! Please use the spare wheel holder for the TD5 linked below. media/pdf/74/df/0c/Merkblatt-Edelstahl-und-Rost.pdf