Automotive engineering

High-quality seal for the ventilation flaps on Land Rover Series III and Land Rover Defender up to and including model year 2006 In contrast to the original parts made of foam rubber, this is a fully-fledged sealing material. The seals give way slightly over time. You can (re)glue them in with a PU adhesive.  Scope of delivery: 1 piece

Set for cleaning and impregnating The K&N air filter cleaning and maintenance kit consists of one bottle of K&N air filter cleaner and a bottle of filter oil to re-apply filter oil. In normal conditions cleaning should be done every 80.000km, in heavy conditions (industrial use, desert raids, rallye driving) cleaning intervals should be shortened and visual checks should be made frequently. Instructions: Spray K&N filter cleaner on cotton filter onto both sides and allow to soak for 10 minutes to loosen the dirt. Make sure cleaner does not dry. Rinse off cotton filter with cool no-pressure water from the clean side out to the dirty side until all traces of cleaner and dirt have been washed out. You might have to repeat the previous and this step. Shake water off and leave to dry naturally in the air. Don't oil filter before it is completely dry. Spray surface of each filter pleat with K&N filter oil from a distance of about 8cm (3"). Leave oil to wick for about 20 minutes and re-oil any light areas until there is an even red colour on all areas.

Repair kit for tailgate hinges screwed version1 set, see pictureOnly suitable for hinges with screwed bolts.Does not fit hinges with pressed bolts.

Connector / mating connector for Land Rover Defender switch OEM Style Suitable connector / mating connector for switch YUG000540LNF / YUF500150LNF / YUG102440 or our OEM style switches Scope of delivery: connector incl. contacts As spare part for our switches: Switches for Land Rover Defender & Discovery Switch with bezel for Land Rover Defender & Discovery Land Rover Defender OEM switch auxiliary headlights

The Perfect Cover: Hub Cap for Your CW Wheels Do you pay attention to every detail on your off-roader? Then the matching hub cap for your CW wheels is an absolute must! This cap is not only a visual highlight but also reliably protects the wheel hub from dirt, dust, and moisture. Perfect Fit and Stylish Specially designed for CW wheels, this hub cap fits like a glove and seamlessly integrates into the design of your wheels. It completes the overall look of your vehicle and ensures a clean, professional appearance, whether you're stuck in the deepest mud or conquering the road. Protection That Pays Off The wheel hub is an important part of your chassis. With this hub cap, you effectively protect it from external influences that could promote corrosion or wear. A small investment that contributes to the longevity of your components. Easy Installation Installation is child's play and done in no time. So you can quickly and easily ensure optimal protection and the perfect look for your wheels. Add the finishing touch and protect your wheel hubs at the same time – with the custom-fit hub cap for your CW wheels from Nakatanenga! Available for CW rims in sizes 7x15", 7x16" , 8x15" and 8x16", colors: silver, with CW Logo

Adapter kit for cyclone filter ZYKL N - suitable for snorkels with 80-85 mm diameter With this adapter kit, the cyclone pre-filter ZYKL N can be quickly and reliably fitted to snorkels with an outer diameter of 80-85 mm. The ideal solution for anyone who wants to efficiently protect their air intake tract from dust, sand and dirt - especially in off-road or desert use. With the adapter kit, you can optimally upgrade your snorkel and improve the filter performance of your air intake system - for longer maintenance intervals and better performance in demanding conditions.  

Suzuki Jimny GJ / HJ Adapter cable PS13W to Superseal 3-pin Hard-working 4x4s like the Suzuki Jimny GJ / HJ benefit greatly from partial or complete conversion to LED lamps and lights: as a rule, LEDs tend to shine brighter while using less energy, are not as prone to failure and last longer than bulbs. If you want to customize your Jimny GJ / HJ with combined LED daytime running and fog lights, e.g. Nolden 90 mm LEDs, you will need 2-pin PS13W socket to 3-pin AMP-Superseal plug adapter cables to connect the daytime lights. The fog lamps are plug & play. The complete installation kit consisting of two adapter cables and one pair of Nolden LED daytime running/fog lights in chrome housing can be found here. Adapter:2-pin PS13W socket to 3-pin AMP-Superseal plug.

Ring LED bulbs type R207 R5W These bulbs have a long life and are more resistant than conventional bulbs. Technical details:12 V60 lumens3,000K (white) Advantages: vibration-proof durable more resistant was developed to replace a conventional car lamp Delivered is a set consisting of 2 lamps. IMPORTANT NOTE:Not approved for the STVO!

Ring LED Bulbs Type RW2336FSLED 233 T4W These bulbs have a long life and are more resistant than conventional bulbs.Compared to halogen, these LED lamps have a much lower power consumption. Technical details:12 V40 lumens6,000K (white)0.5 watts Advantages: vibration-proof durable more resistant was developed to replace a conventional car lamp Delivered is a set consisting of 2 lamps. IMPORTANT NOTE:Not approved for the STVO!

Washer pump including grommet Suitable for Land Rover Defender MY 87-98 without air conditioning

Plastic expanding rivets, black Plastic dowels for door panels and mudguard extensions for Land Rover Defender

Repair kit for fuel cooler The repair kit for the fuel cooler consists of 4 rubber rings which ensure a secure seal. Suitable for the fuel cooler PIB000060 (see illustration) of the Defender Td5 and the Discovery II.

Mounting tool for studs with Ø 9mm Bit (tool) for mounting spikes with a diameter of 9 mm on winter wheels.Easily compatible with a cordless screwdriver due to the hexagonal profile of the screw head.Note: Tyre studs are prohibited in GermanyAssembly steps:1. position the head of the corresponding studs with the mounting tool2. place the thread of the stud on the tyre surface3. press down & screw in with a cordless screwdriver while turning slowly4. screw in the spike only until the head touches the tyre surface5. if the spike is unintentionally screwed in too far, leave it as it is - do not unscrew it to try to get it into the correct position6. check the spikes every 1000km & correct if necessary7. with the aid of the fitting tool and a cordless screwdriver, the studs can be gripped & removed

Power screwdriver bit 1/2 inch with plastic sheath, to protect the rim Features: Design: hexagonal (HEX)Features: with protective sleeveDrive size: 1/2 inch (12.5 mm)Wrench size: 22 mmTotal length: 85-86 mmMax. Torque: 961 Nm (97 kg/m) Material: Chrome molybdenum steel (Cr-Mo), forged and hardened Suitable for impact wrench and torque wrench !

Fuel filter mounting set - Defender Practical mounting set for secure mounting of the fuel filter on the Land Rover Defender. Ideal as a replacement for defective brackets or for conversions. Robust quality, perfect fit for various Defender models.

Replacement bracket and lock for rear door canister holder The locking bolt can be secured by means of a padlock and is made of high-quality stainless steel.

LOF Clutches Clutch Alignment Tool This tool enables you to correctly align clutch discs in most Land Rover models. The alignment tool is CNC machined from black Nylon and will suit TDI, TDCI Puma, TD5, 2.25 and all 4-cylinder engines on Series I - III.

Damper repair kit Inspection set for TREKFINDER steering damper - eye Delivery: 1 piece rubber bush1 piece of metal sleeve -------------------------------------------------- --------------------------------- Inspection set for TREKFINDER steering damper - pin Delivery: 1 piece hex nut1 piece metal plate outside2 pieces of metal plate inside2 pieces of rubber buffer

Spring Spacer Ring/ Trim Packer/ Lifting Ring TREKFINDER for SUZUKI Jimny I & II + 10 Millimeter in colour red - for levelling at the front or/and rear axle. Suitable for all Jimny models at the front and rear axle: Jimny II type GJ & HJ as of MY 2018 Jimny I type FJ until MY 2018 for the front axle spring for the rear axle spring 10 millimetre height adjustment SCOPE OF DELIVERY: 1 piece TREKFINDER polyurethane spring distance ring with marking TREKFINDER logo + FDR10 in colour red. NOTE: The spacer rings are listed in the TÜV® parts certificate for our TREKFINDER Jimny II complete suspension 40 mm and Jimny I suspension 55 mm and can therefore be optionally installed 1x per spring.A general TÜV® parts certificate is not available or is NOT included in the scope of delivery. MOUNTING INSTRUCTIONS: The installation is carried out between the upper end of the spring and the spring plate. Make sure that the brake line is long enough Make sure that the shock absorber is long enough. Check the headlight setting. The permissible height of the coupling ball must be observed. If there is a load-dependent headlight adjustment, e.g. for LED lights, this must be checked and, if necessary, adjusted or changed/extended. If a new measurement or calibration of the sensors of the driver assistance system is necessary due to the changed vehicle geometry of the vehicle, this must be carried out according to the specifications of the vehicle manufacturer. For vehicles with load-dependent brake pressure regulator, this must be readjusted to the empty level (according to the vehicle manufacturer's specifications). After retrofitting, the axle geometry of the vehicle must be measured and, if necessary, corrected according to the vehicle manufacturer's specifications.

AGR/EGR- closure plate for either the Td5- (- MY02) or the Tdi-engine, to eliminate exhaust gas recirculation. Comes with the necessary bolts. Motorsportequipment, not certified for road use.

LOF Clutches Centring Tool This clutch centring pin from LOF Clutches is used to correctly align clutch discs on all ROVER V8 applications with 549991 spigot bush. Made from CNC machined plastic, the clutch arbor fits vehicles with the following engine options: SKU: V8-CAT Categories: Land Rover Series Clutches, Clutch Parts, Land Rover Defender Clutches, Land Rover Discovery Clutches, Range Rover Clutches Tags: 1.6L/2.0L Clutches, 2.25 (Petrol/Diesel) Clutches, 2.8 tgv Clutches, 200/300 Tdi Clutches, Td5 Clutches, TDCI (2.4/2.2L) Clutches 

Plastic hub cap set of 4 WITHOUT LR-LOGO - Suitable for Discovery 1 1989-1998, all Defender and Range Rover Classic Scope of delivery: 4 pieces

Axle stop rubber for Land Rover Defender up to BJ 2016 Specification: Category: Axles and Suspension Engines: All Fuel: Diesel, Petrol Premium range: ANR4188G: Yes / ANR4189: No Transmission: Manual, Automatic Specification NAS - North American Specification, NOT-NAS - Non North American Specification Quality rating: 100 Drive Type: Drive Wheel 2WD - Two Wheel Drive, 4WD - Four Wheel Drive Fits DEFENDER 1986 - 2006, DEFENDER 2007 AFTER, DISCOVERY 1 1989 - 1998 and RANGE ROVER CLASSIC.

Ballistol Rim Cleaner is an extremely powerful gel cleaner with an active indicator This means that a colour change occurs with increasing effective power (the cleaner turns purple). Removes stubborn dirt such as brake abrasion, oil and rubber residues highly effectively and automatically. Also suitable for TPMS (tyre pressure monitoring system). cleaning status is indicated by colour change foams up when sprayed removes light rust film tested material compatibility for all rims (steel, aluminium high-gloss, multi-piece, matt) neutral towards rubber and painted surfaces odour-reduced, acid-free and biodegradable without nanotechnology Note: Do not use on warm rims or in the blazing sun. Rinse thoroughly, do not allow to dry. Protect from frost. Check material compatibility on an inconspicuous area before use. Caution:Harmful if swallowed. May cause allergic skin reactions. Causes severe eye irritation. If medical advice is needed, have packaging or label at hand. Keep out of the reach of children. Wear protective gloves / protective clothing / eye protection / face protection. In case of contact with eyes: Rinse cautiously with water for several minutes. Remove contact lenses if possible. Continue rinsing. Dispose of contents / container for recycling.

1/2" Nut for wheel nuts, 27mm Nut with SW 27, suitable for our NA ZURM wheel nuts, for 1/2" drive.

Silencer / spacer for height compensation (rover axis) The article can be used on the front axle on the 90/110/130 and on the rear axle on the 90. Optimal possibility for level adjustment / the raising is 10 millimetersThe rubberized surface of the ring reduces the transmission of vibration noisesThe washer is placed between the spring end and the spring plate, a maximum of one washer per spring end is possible, i.e. H. a maximum of two washers per spring, so a maximum height of 20 mm per spring is possible. Price per piece

Plastic Rivet Set for Defender Grille and Bumper These rivets are used on all models of the Land Rover Defedner from 1987. The plastic rivets are suitable as end caps for Land Rover Defender bumpers or e.g. also as a clip on the grille and on some interior panels. Fits a 7 mm holeHead diameter: 18 mmTotal wavelength 27 mm

Mounting screw suitable for mounting bracket injection nozzle - Defender TD4 2.2 and 2.4 here in the store

Reliable Visibility in All Weather Conditions These classic front wiper blades are a perfect fit for all Land Rover Series II and III models. Designed to match the original mounting system and equipped with durable rubber blades, they ensure clear visibility – whether it’s rain, snow, or mud. Details: Suitable for Series II / IIA / III Original length and mounting style Sturdy metal frame in black finish Easy installation – plug & play   Ideal for those who value both functionality and original appearance. Suitable for left and right sides – please check quantity when ordering.

Land Rover Cover Cap for Windscreen Wiper Arm for Defender 90/ 110/ 130 year of construction 2001-2016

Secure Hold for Your CW Wheels: The Right Wheel Nut for Your Defender You know that every detail counts when you're off-road – and that's especially true for the connection between your robust CW or LD Borbet wheels and your Land Rover Defender. With these special wheel nuts, you ensure an absolutely secure and reliable fit for your wheels, no matter how demanding the terrain gets. Precision Fit for Your Safety These wheel nuts are precisely matched to the requirements of CW and LD Borbet wheels in combination with the Land Rover Defender. A correct and securely tightened wheel nut is crucial for your safety and the performance of your vehicle. Trust in material and design specifically developed for this combination. Quality You Can Rely On Made from durable material, these wheel nuts offer the necessary stability and longevity you expect in off-road use. They withstand the stresses and ensure that your wheels stay firmly in place even under extreme conditions. Essential for Assembly and Maintenance Whether you're mounting new wheels, changing a tire, or simply want to ensure all components are in top condition – these wheel nuts are the right choice. It's always advisable to have suitable spare nuts on hand or to replace old, worn nuts in good time. Ensure the perfect and secure connection for your wheels. With these wheel nuts specially designed for your CW or LD Borbet wheels on the Land Rover Defender, you're always on the safe side! Wheel nut for CW rim for Land Rover Defender, M16x1.5, SW21

Wheel nuts for Discovery II ZU rim - With stainless steel cap for optimum protection These specially developed wheel nuts are the perfect complement for the original Land Rover Discovery II ZU rims. They combine a precise fit with robust durability and are additionally equipped with a high-quality stainless steel cap - for a clean finish and optimum protection against dirt, salt and corrosion.