Das könnte Sie auch interessieren
TREKFINDER wheel spacer kit for INEOS Grenadier + 66 millimetres Track widening 66 mm by fitting spacer rings on the front and rear axle or only on the rear axle in conjunction with alloy wheels or standard INEOS Grenadier steel wheels. The following vehicles are approved according to the TÜV parts certificate: Vehicle manufacturer: Ineos Automotive (UK) / 2295Vehicle type: GN, GMCommercial designation/version: INEOS GRENADIER 6-cylinder diesel & petrol engine, 2+5 seaterEC - TG - No. : e9*2018/858*11384*... ; e9*2018/858*11385*... The following wheel/tyre combinations are approved according to the TÜV parts certificate: 265/70R17 with 7.5x17255/70R18 with 8.0x18 Scope of delivery: Selectable: 2 pieces (1 axle) or 4 pieces (2 axles) Aluminium wheel spacer plates, black anodised1 set of fixing nuts1 set of fitting and care instructions1 TÜV parts certificate Notes on installation:The screw-in length of all fastening elements must be at least 7.5 turns (M14x1.5).Ensure that the stud bolts are long enough.The bolted-on spacer rings are fastened to the vehicle using the fastening elements supplied by the spacer ring manufacturer (M14x1.5 tapered collar). The standard wheels are fastened with the standard fastening elements.The standard stud bolts may protrude slightly (up to 2 mm) beyond the wheel contact surface of the spacer rings. In conjunction with the standard Ineos steel wheels or LM wheels without "cast pockets", which can accommodate the standard stud bolts and nuts protruding beyond the wheel contact surface, the standard stud bolts must be shortened slightly. The minimum screw-in length of all fastening elements of 7.5 turns must be maintained. Wheel cover requirements:Adequate coverage of the wheel/tyre combination must be achieved by fitting 35 mm wide, permanently attached wheel cover extensions.The surface-mounted wheel cover extensions must be fitted at an angle of 30 degrees to the front and 50 degrees to the rear in relation to the vertical centre line of the wheel. Notes on the modification measure:There are no technical objections to the use of standard or other wheel/tyre combinations up to the above (limit) wheel/tyre combinations in conjunction with the described spacer rings if the following conditions are met: - Separate suitable expert reports are available for the wheel/tyre combinations and the conditions listed therein are complied with. In addition, the above-mentioned conditions must be observed and applied if necessary.- If other wheel/tyre combinations are used, their suitability (freedom of movement, driving behaviour, etc.) must be checked and verified separately.- There are no technical objections to the additional use of tested lowered or raised suspension (with parts certificate or ABE). In the case of suspension modifications with non-standard end stops, the suitability of the conversion must be checked or verified separately.
Prices incl. VAT;
The Rockslider for the INEOS Grenadier is made of stainless steel in Germany and impresses with its function and striking design. In order to increase the stiffness in the event of a lateral load in off-road use, the lateral slotted holes are turned inwards. Mounting is done on original mounts without drilling.The Rockslider is mounted directly underneath the doors instead of the plastic trim. Due to the high exposed position of the Rockslider, the ramp angle of the INEOS Grenadier is not changed or impaired. Our Rockslider not only serves to protect the bodywork, but also provides a secure footing thanks to its non-slip surface made of drawn nubs. Due to its shape, the Rockslider also protects against excessive dirt in the field. The dirt collected can be rinsed out again through openings on the underside. The Rockslider, as well as the two holders - made in Germany - are powder-coated in black or red and can be ordered in the combination that matches the vehicle. Suitable forUtility 2 & 5-seaterStation Trial & Fieldmaster Technical data:25 kg per Rockslider incl. bracketMounting on original mounting points Delivery:1 set Rockslider stainless steel (left & right)Bracket and mounting material (left & right)Set of stainless steel screws As a useful add-on, there are matching anti-slip pads for the Rockslider.
Prices incl. VAT;
The high-quality sliders made of 3mm stainless steel fit all Mercedes G-models 461 and 463 and can be easily attached to the original stopping points of the running boards. The stable design offers optimal protection for your vehicle from the side and from below. The fitted shape fits perfectly to the silhouette of the vehicle and the high seat of the "G-Silde" also ensures an unchanged ramp angle. The distinctive design of Abeneuer4x4 also applies to this product "Made in Germany": the drawn knobs. These also offer a non-slip surface and ensure a secure stand. Dirt can be rinsed out through openings on the underside of the slider. Material:Stainless steel, black powder-coated Important NOTE:The original screwing points of the running boards must be available for smooth installation of the G-Slide. Scope of delivery:1 set of rock sliders (left & right) including holder and fastening material. As a useful add-on, there are matching anti-slip pads for the Rockslider.
Prices incl. VAT;
Running boards Land Rover Defender Why skimp on comfort and looks? These running boards for Land Rover Defender 110 not only look good, they also provide a safer and more comfortable entrance to your vehicle. The round tubes are black powder-coated and equipped with checker plates. The chequer plates on the entrance tubes have an anti-slip coating so that you can enter your vehicle safely.Fixing material is included in the delivery.Important note: These running boards are not compatible with the original splash flaps (front). You will find the matching mud flaps here as well as matching splash flaps here.They are delivered in pairs.Material thickness checker plate: 2.5 mm basic thickness / 4 mm incl. checker (quintet plate)You can find a suitable crossbar here.
Prices incl. VAT;
Abenteuer4x4 - Rockslider - for Land Rover Defender The stainless steel Rockslider by Abenteuer 4x4 for the Land Rover Defender 90/110/130CC convince by a completely new design, low weight (approx. 12 kg/piece) and an easy mounting without drilling.To increase rigidity, two webs are welded on the back and the slotted holes on the long side are turned inwards.The Rocksliders not only serve to protect the bodywork, but also provide a secure foothold thanks to their non-slip surface made of drawn knobs, and their shape also protects against excessive dirt in the field. There are several openings on the underside for rinsing out dirt that has been picked up.The Rocksliders - made in Germany - are powder-coated black. Delivery includes fixing material.This item is bulky goods.Material: stainless steel, black powder coatedMaterial thickness: 3mm Delivery: 1 set Rockslider stainless steel (left & right)Bracket and fixing materialSet of screws stainless steel As a useful add-on, there are matching anti-slip pads for the Rockslider.You can find a suitable crossbar here.
Prices incl. VAT;
Ähnliche Artikel
Self-adhesive anti-slip pads Perforated metal sheets, as used on our CargoBear roof racks, on ladders, steps and other climbing aids on vehicles, are much safer than regular metal surfaces. Additional anti-slip pads, however, offer an unbeatable safety advantage, especially in wet or dirty conditions. The anti-slip pads are designed to perfectly match the hole patterns and due to its black color, they also compliment the overall look of our products. The material for the pads originates in the sports sector and has been widely used on skateboards, for example. For our spare-wheel strap-on step, we offer ready-cut, self-adhesive anti-slip pads measuring 12 x 13.5 cm in twin packs. Since the pads are manufactured with in-house laser cutting technology, we can supply custom formats on request.
Prices incl. VAT;
Self-adhesive anti-slip pads Perforated metal sheets, as used on our CargoBear roof racks, on ladders, steps and other climbing aids on vehicles, are much safer than regular metal surfaces. Additional anti-slip pads, however, offer an unbeatable safety advantage, especially in wet or dirty conditions. The anti-slip pads are designed to perfectly match the hole patterns and due to its black color, they also compliment the overall look of our products. The material for the pads originates in the sports sector and has been widely used on skateboards, for example. For the CargoBear, we offer ready-cut, self-adhesive anti-slip pads measuring 16 x 24 cm individually or in sets of 3, 6 or 12. Please note: the multi-packs provide increasing savings regarding the price per item. Since the pads are manufactured with in-house laser cutting technology, we can supply custom formats on request.
Prices incl. VAT;
More safety and a firm grip wherever you need it Slippery surfaces are a constant challenge and source of danger in demanding off-road use, but also in the daily use of an off-road vehicle. Whether due to wetness, mud, snow or simply slippery materials - the risk of slipping is always present. With the high-quality anti-slip strips from Nakatanenga, you can effectively ensure greater safety and surefootedness on all critical surfaces of your vehicle. Why are anti-slip strips an indispensable accessory? Our self-adhesive anti-slip strips offer a simple and extremely effective solution to significantly reduce the risk of slips and falls. The advantages speak for themselves: Increased safety: provide excellent grip even in damp, dirty or slippery shoe soles. Minimise the risk of accidents when getting in and out of the vehicle or when loading. Versatile application: Perfectly suited as anti-slip protection for running boards, bumpers (e.g. as bumper protection), mudguard tops, rear cross members, loading areas, roof racks or other accessible surfaces on the vehicle. Also ideal for trailers or in the workshop area. Robust quality for off-road use: Our safety strips are made from hard-wearing materials that are UV-resistant, weatherproof and abrasion-resistant. They also withstand the harsh off-road conditions. Easy to install: The anti-slip strips are self-adhesive and can be applied quickly and easily to clean, dry and grease-free surfaces. Unobtrusive design: Our strips offer effective protection without detracting from the appearance of your vehicle. The right anti-slip strips for your needs at Nakatanenga At Nakatanenga, we emphasise quality and functionality. Our anti-slip strips are carefully selected to meet the high demands of the off-road sector. Optimise the slip resistance of your Land Rover Defender, Toyota Land Cruiser, Jeep or any other off-road vehicle. Trust in the proven Nakatanenga quality and invest in extra safety. Tip: For optimum adhesion, we recommend thoroughly cleaning and degreasing the surface to be covered in advance. Declare war on smooth surfaces now! Set with 4 anti-slip strips Dimensions: 270x50 mm sanded self-adhesive ultra-sticky not removable due to moisture The strips are cut in-house using a precision laser. Special sizes are also available on request. Please simply contact us by e-mail or telephone.
Prices incl. VAT;
Anti-slip pad for Adventure 4x4 Rockslider, for Land Rover Defender and Ineos Grenadier, 1 pair
€16.00
Prices incl. VAT; / Parcel shipping
Secure hold on rock sliders – especially for Defender & Grenadier
These self-adhesive anti-slip pads with their precise fit are specially designed for the Adventure 4x4 rock sliders for Defender and Grenadier. The pads are perfectly matched to the sliders’ hole pattern and they improve the Rocksliders’ good anti-slip properties even further, especially in wet or dirty conditions. The 5.5 x 50 cm adhesive strips are supplied in pairs. The dimensions are matched to the door area, but with sufficient quantity and some adjustments it is also possible to cover the entire surface.