Adjustment adapter for electric speedometer / odometer When fitting new tyre sizes, modern vehicles with a factory-integrated speedometer usually have a speedometer discrepancy, as this is often not configurable. In the long run, the incorrect speed indication is annoying and sometimes results in an incorrect total kilometre reading (the odometer goes wrong) and consequently even in a poorer resale value of the vehicle. The speedometer adjustment with the adjustment adapter is an inexpensive solution to avoid this problem.Technical data:Power supply: 9 - 28 voltsQuiescent current consumption: 4.6 mA at 13.8 volts power supplyInput signal: min. 2 volt peak, potential-independent, max. 4.5 kHz at 12 volt input signal or max. 1.6 kHz at 5 volt input signalOutput voltage: square-wave signal equal to the operating voltage minus 1.3 volts, maximum 13.1 volts, maximum 5 kHzSecond output stage with sine wave signal

Adjustment adapter SpeedoHealer  When fitting new tire sizes, modern vehicles with a factory-integrated speedometer usually have a speedometer discrepancy, as this is often not configurable. In the long run, the incorrect speed indication is annoying and sometimes causes an incorrect total mileage (the odometer goes wrong) and consequently even a poorer resale value of the vehicle. The SpeedoHealer speedometer alignment is an inexpensive solution to avoid this problem. Suitable for TD5 vehicles from MY1998 to 2007 The alignment adapter is simply connected to the green speedometer sensor located on the transfer case of the Defender. The SpeedoHealer then detects the correct speed from the output pulse of the speedometer sensor. Functions of the SpeedoHealer: Speedometer adjustment or elimination of inaccuracy of the original speedometer.Conversion of kilometers to miles or miles to kilometers (useful for a vacation abroad or for imported vehicles)Accurate indication of the maximum speed driven at the push of a buttonNeutralization of the speed limiter on some vehicles

Cruise control for Land Rover Defender Td5 MY02-MY07 Especially on longer journeys, it's quite tiring to hold the throttle in the Defender. Our new cruise control puts an end to that.Now, at the touch of a button, Defender will maintain the desired cruising speed. The cruise control takes over the current speed and maintains it - exceptions:    if the engine power is insufficient (e.g. high speed and at the same time a significant rise in the road), the cruise control switches off for safety reasons.     when the brake or clutch pedal is pressed.The cruise control is operated via 2 supplied stainless steel buttons:    a SET button to hold and increase the current speed.     a RESET button for switching off the cruise control, as well as for resuming the last set speed.The delivery is made as a complete set incl. detailed and illustrated instructions, which also enable "occasional screwdrivers" to assemble it.Time required: about 1-2 hours.Conclusion: A "must" for all those who often drive on the motorway or undertake long-distance journeys - even the journey to the port in Genoa, for example, becomes a "relaxing" experience...Please note: Really only suitable for Td5 MY02-MY07. The decisive factor is the installed control unit. The identification number of the control unit must start with NNN or NNW! If the identification number begins with MSB, this cruise control is not suitable.

Speedometer calibration kit for Suzuki Jimny from 2018 (Type GJ und HJ) This tachometer calibration kit can be used to correct the speed display and distance counter for vehicle conversions with a tire roll circumference that differs significantly from the series.Changes to the differential or larger tire roll circumference can thus be made acceptable.The ABS / ESP control unit sends a speed signal to the instrument cluster via CAN bus. The speedometer calibration kit is installed in front of the instrument cluster and corrects both the speed signal and the odometer in real time. The correction factor can be programmed via USB interface. The original wheel speed signals are retained. The function of the ABS / ESP control unit can therefore not be impaired. Technical specifications:EC type approval: E1 10R-036407Correction factor: 1-255%Default: 106%Power supply: 6-30V DCPower consumption sleep mode: 10 mACurrent consumption max .: 35 mATemperature range: -40 ° C / + 125 ° CDegree of protection: IP68 Also available for other vehicles on request.