TEXU400 central electrics for touring vehicles and boats The TEXU400 revolutionises electrical installation. It combines various components that previously had to be purchased individually in a round housing that optimises the use of space and the number of possible connections in the smallest possible space. The special arrangement, which is ONLY available in the TEXU400, enables system integration with groundbreakingly low effort. This results in drastic savings in costs as well as time and space, while at the same time reducing sources of error and providing the highest level of application comfort after installation. It also requires considerably less installation space in a touring vehicle or boat. Extensive electrical systems can thus be planned in a smaller space and the space gained can be used for other purposes. Connection of up to 4 battery banks 11 high-current and 4 standard consumers Plus rail for on-board batteries and consumers Screw terminals and fuses 2x MEGA / AMG fuse max. 400 A 9x MIDI / AMI fuse max. 170 A 4x ATO / ATC / ATP fuse max. 30 A 1:1 ground distributionPut an end to insufficient ground distributions! With the TEXU400, a negative connection is also provided for each positive connection. Simple integration of a summation current measurementThe factory-fitted Sunt bridge between the negative busbars can be easily removed by means of screws and replaced by a plastic bar included in the scope of delivery to enable quick and uncomplicated integration of a measuring shunt. MEGA fuse with double inputWhere cable lugs used to be stacked or other suboptimal constructions had to be devised on a case-by-case basis (e.g. in the case of split cables of powerful inverters), there is now a professional solution: a MEGA fuse point with max. 400 A and double screw connection, ensures professional and safe installation of such components. Ignition-protected according to ISO 8846The UFO is ignition-protected according to ISO 8846 with the integrated, all-round bar with seal. It is therefore also approved for installation in the engine compartment. LED failure check with fibre optics Immediate diagnosis. Fibre-optic cables light up the LED failure check directly at the inscription of the circuits in the closed cover. You can save yourself the trouble of removing fuses and searching upside down for faults in confined spaces! A prefabricated labelling set with partly customisable content is included in the scope of delivery of the TEXU400. Space for spare fusesThe TEXU400 contains additional slots for spare fuses (1x MEGA, 2x MIDI, 2x ATO/ATC/ATP)Convenient opening and closingThe knob centrally located on the enclosure cover makes it easy to open and close the cover and even allows one-handed operation in confined spaces. Please note: As individual electrical installations contain different components that must be suitably fused, a prefabricated fuse set is NOT included directly in the scope of delivery of the TEXU400.

Power distribution box with fuse holder from BlueSea Compact size BlueSea blade fuse block and power distribution for either six or up to twelve seperately fused circuits for up to 30 Amps per electronic installation and currencies up to 32 volts. Fitting a variety of cars with 6 V up to 24 V supply systems. These fuse boxes also provide a common negative bus to minimize bad earth problems. New version offers two separate circuits, thus allowing e.g. 6 installation with permanent life feed and 6 with ignition life feed. This fuse box can be the starting point for well laid-out and safe vehicle electrics and should be fitted from early on when starting fitting additional appliances and electical installations. The box itself should be fused - not more than 30 cm away from the battery with a maximum of 125 A - for which we recommend our fuse carrier (up to 200 A) from the same supplier with the suitable 125 A MIDI strip fuse. Comes with: fuse box for either 6 or 12 circuits clear plastic cover with recessed placeholder for lables two slots for spare blade fuses no fuses supplied Technical details: Modell SHMA-6 SHMA-12 SHMA-6+6 number of circuits max. 6 max. 12 max. 6+6 placeholder for spare fuses 2 2 2 dimensions 125x85x39 mm 165x85x39 mm 165x85x39 mm weight 250 Gramm 350 Gramm 350 Gramm max. per circuit max. 30 A max. 30 A max. 30 A max. overall max. 100 A max. 100 A max. 100 A max. voltage max. 32 V max. 32 V max. 32 V Please choose number of circuits.

High-quality fuse holder for 6 independent circuits This robust fuse holder offers space for up to six separate circuits and ensures reliable protection for your electrical system. Each circuit can be loaded with up to 30 amps, which enables flexible use in a wide range of applications - whether in the automotive sector, boats, motorhomes or other 12V or 24V vehicle electrical systems.Thanks to its design for a maximum operating voltage of 32 volts, the fuse holder is ideal for DC networks in the low-voltage range.The transparent cover supplied protects the fuses from external influences and also enables a quick visual check. Practical: The cover has integrated labelling fields for easy identification of the individual circuits as well as a holder for a spare fuse - so a reserve is always to hand in an emergency.

Complete package consisting of a PowerPort Pro (socket), a PowerClip Pro (plug) and a PowerPort cover, for 12 V. Magnets in both the PowerPort (current transmitter) and the PowerClip (receiver) contact the two components and also have a switch function. Therefore, the flat contacts of the PowerPort are only energised when the movable magnet plate in the encoder is switched by a suitable pick-up. Other metallic objects or magnets cannot trigger the switching process. Thus, a MagCode Pro PowerSystem is 100% short-circuit-proof. The MagCode Pro system can be used for a variety of applications where safe but easily detachable power connections are required - whether it is the cool box in the off-roader or the battery charger - but also headlights on the roof rack or the power supply in the roof tent can be solved in this elegant and contemporary way. Technical data: Locking: magnetic and mechanicalPowerPort connection: 6.3 mm flat contact for plugging or solderingPowerClip connection: Screw connection, max. 2.5 mm² cablePowerPort installation diameter: 28 mm (M28)PowerClip projection: 21.5 mmVoltage range: 12 Volt (also available for 24V)Load capacity: max. 25 amps (at +70°C)Port cable length: 72 mm Dust and waterproof : PowerPort front (built-in): IP5K9KPowerPort connection side: IP5K0PowerClip (not connected): IP40PowerClip (on port): IP42Switching cycles (without load): over 10,000Switching cycles (under load): 4,000Please note the instructions for outdoor use