Dixon Bate adapter for Bikeracks and Game Tubs

Nakatanenga adapter for hitch-mounted racks for bikes and other sports gear Hitch-mounted racks for bikes and other sports gear are a great solution if the bikes are only used occasionally or taken along on an annual holiday trip. No cumbersome attachment to roof rails or the rear of the vehicle is needed: simply mount the rack on the vehicle’s tow ball and off you go. So much for the theory, because for many 4x4 owners, the rear-mounted spare wheel is usually in the way of a conventional hitch-mounted bike rack. But that’s where Nakatanenga comes in. Our premium quick-release adapter mounts securely and lockably onto the existing tow ball and extends the coupling point by 25 cm. In most cases, this provides enough clearance for a bike rack to fit behind the rear-mounted spare wheel. It is advisable to take careful measurements before ordering to make sure that the 25 cm extension is sufficient for the individual vehicle and wheel/tyre combination. Please also note that the lockable quick-release handle on the right-hand side requires sufficient space. The existing tow hitch must therefore be fully accessible and must not be restricted by recessed bumpers or similar vehicle components. With a maximum load of 120 kg, the adapter is ideal for standard bike racks, cargo carriers, tubs, baskets and similar carrier systems. Since there are occasional questions regarding the maximum load, we would like to emphasise – as the manufacturer – that the specified maximum load of 120 kg applies to the complete adapter assembly and has been determined in extensive load and safety testing. Any differing load ratings for separately available individual components are therefore not relevant to the permitted load of the complete adapter assembly. Please check the applicable road traffic regulations and legal requirements for the respective country when using the adapter. CAUTION!For technical and legal reasons, the adapter MUST NOT be used for towing a trailer. The coupling point is extended by 25 cm.

Compact rechargeable tyre pump The OSRAM TYREinflate 2000 is a rechargeable tyre pump with a digital backlit display for easy and accurate pressure measurement and inflation of tyres, showing pressure values in BAR, kPA and PSI. The OSRAM TYREinflate 2000 has an internal memory and, thanks to the memory function, up to four different values can be programmed and stored for different tyres. It is also equipped with an auto-stop function: the OSRAM TYREinflate 2000 stops automatically when the preset pressure is reached. Thanks to the USB cable supplied, the OSRAM TYREinflate 2000 is rechargeable and no 12V socket is required for the power supply, so it is not only used for inflating car tyres, but can also be used for inflating bicycle, scooter and motorbike tyres. Thanks to its lightweight and compact design, the OSRAM TYREinflate 2000 is ideal for travelling and can be taken almost anywhere. Simply stow it in the glove compartment of your car, a bag or a rucksack using the storage bag supplied. A bracket for mounting and storage on a bike is also included. Thanks to the power bank function, the OSRAM TYREinflate 2000 can also be used as a charger for electronic devices such as your mobile phone. In addition, the integrated torch function can provide illumination at night or in poor lighting conditions. The scope of delivery also includes a 2-piece adapter set that can be used as a connection for bicycles, balls and other inflatable objects with Presta valves. OSRAM grants a 2-year guarantee* on this product   Product information       Charging time: approx. 3 hours Inflation time: <2min 0-5.5bar bicycle tyre Tube length: 14.5cm     Units of measurement: PSI, kPa, bar Maximum pressure: 120 PSI, 8.3 bar Accuracy (bar): 0-1.5 PSI / 0.10bar     Mains cable length: N/A Display size: 30x155mm  Flow rate (1/min): N/A     Electrical data       Power supply: USB Cable Nominal voltage 3.7 V Nominal power 67.00 W  Rechargeable battery (5200 mAh)  Dimensions & Weight       Length 70.0 mm Height 170 mm Width 70.0 mm Product weight: 500g   Additional product data       Display type Digital Noise level (dB) 83 dB Fuse 18 A   Recommended area of application Bicycles, motorbikes, cars Accessories:Adapter for bicycles & small inflatable sports equipment. USB charging cable, power bank system, LED light, storage bag, bike holder Please note the legal information on batteries HERE. For certain types of batteries, we are legally obliged to charge a deposit.    

Hitch-mounted racks for bikes and other sports gear are fantastic, if you are using your bikes only off and on or once a year on your annual holiday trip. No cumbersome attachment to the roof rails or the trunk needed: simply lock it onto your car’s standard ball hitch when you need to and hey presto, off you go. Theoretically, that is, because for most 4x4 owners, the rear-mounted spare wheel will usually be in the way of a regular hitch-mounted bike rack. But that’s where Nakatanenga comes in.As an alternative to our lever operated quick-release adapter, we also provide an adapter that can be screwed onto the existing ball hitch. The extension you gain is the same as with the other adapter: 25 cm to the back. It will take a little bit longer to attach or detach the screw-on version, of course, but it has the big advantage that there’s no lever in the way if you have little space around your trailer hitch. You also don’t have to secure it with a padlock since there’s hardly any worry about theft en route. So, if the quick-release adaptor is not for you because you want to mount a smaller or permanent adapter, this screw-on solution is the one for you. With a maximum load of 120 kg, the hitch-mounted adapter is ideal for standard bike racks, cargo carriers, tubs, baskets etc. Please check the individual road safety regulations and legal requirements for your country when mounting the adapter. CAUTION!For technical and legal reasons, the use of the adapter with a trailer is PROHIBITED. The adapter shifts the ball hitch 25 cm backwards Please note: You need a 24 mm wrench / socket to fasten it (not included!)Check regularly !!Note the drawbar load !!

Ball head for trailer coupling Article is supplied without fastening material! Technical data: Drawbar load 350 kgD17.2 KNapproved by E11 marking

More options for your Dixon-Bate: Standard additional slides Ships without safety pin.  Safety pin available here.

Replacement locking pin for Dixon-Bate towbars As a replacement in the event of loss or similar. The locking pin is an indispensable replacement or additional part for all standard Dixon-Bate trailer coupling systems. It ensures reliable and secure locking of the coupling slide and thus guarantees a firm hold when using the trailer - even under high loads. Delivery incl. safety split pin