Planar 2D Auxiliary Vehicle Heater We offer the Planar 2D auxiliary vehicle heater as a well-priced, powerful alternative to our Webasto auxiliary vehicle heater kits. With their compact size and a heater output of 1.8 kW, the Planar 2D is well-suited for fitting to smaller vehicles, vans, off-roaders, camper vans, boats or in confined spaces. It is ideal for 'typical' off-road vehicles like the Land Rover Defender, Mercedes G oder Jeep Wrangler JK. The extensive fitting kit that is supplied with each heater make fitting easy. The Planar 2D can be easily controlled via its analogous control unit, with 8 settings available from 0,8 - 1,8 kW heat output. Available as both, 12 volts or 24 volts, this heater is European market approved (ECE label) and can thus be fitted independet of TUV approval. The parking heater has approval for the European market (ECE test mark) and can therefore be installed without registration. The hole pattern is the same as that of Eberspächer Airtronic and Webasto AirTop 2000 heaters, so that an old unit could easily be replaced without drilling additional holes.A space-saving version with a 90° angle can be found here.  All Planar auxiliary vehicle heaters are extremely long-lasting and durable, as well as very frugal. The heater can also be used while driving. And extensive range of additional equipment is available in our online shop. Attention Defender drivers: Our extensive Planar full-set for Land Rover Defender not only includes everything needed to perfectly fit the heater to your Tdi, Td5 or Td4 Defender, but also offers considerable savings over the individual purchase of all included items. Comes with: - 12 V or 24 V heater- Optionally analogue PU-5 control panel with rotary control or digital Comfort Control control panel with timer- Thomas Magnet P327" dosing pump- Exhaust silencer- Dosing pump rubber holder- Dosing pump wiring harness- Heater wiring harness- Intake air hose with integrated silencer- Heat protection hose- Exhaust pipe end piece + clamp- Tank intake pipe- 5.5 m fuel line- 300 mm fuel line connector- 1 m corrugated metal exhaust pipe- Fastening material (screws, nuts, clamps, heat-shrink tubing, cable ties)- Operating instructions Technical details: ·         fuel: diesel·         heat output: max. 1.8 kw, min. 0.8 kw·         air volume: max. 75 m³/h, min. 34 m³/h·         fuel consumption: max. 0.24 l/h, min. 0.1 l/h·         power drain: max. 29 W, min. 10 W·         manual start/stop→ On the Autoterm.cz website you will find a calculator for the correct dimensioning of the air heater The AUTOTERM Luft 2D (Planar 2D) is equipped with a height kit!This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents shooting of the combustion chamber when the atmospheric oxygen content drops. The max. Heating power drops in proportion to the amount of oxygen in the air. Roughly one can say: From 2.000 meters the loss of power per 500 m height is approx. 5%. Manufacturer tests up to 3.440 m were no problem. No difficulties are to be expected up to 4.000 m. The software itself calculates up to 5.000 m - however, this has not yet been tested in real height. The separately available control unit with timer (optional extra) features a larger OLED display and more intuitive operation. Temperature, ventilation and output can be configured via a display and various switches. An added timer clock allows you to set the heater to a specific time. OLED display provides maximum visibility with minimum power drain.  Possible settings:- temperature and output- time and date- language (English or Russian) Features of the new timer clock:- daily: one fixed time at which the heater starts each day- individual: up to thee different settings with different days and times. To heat your roof tent using your auxiliary heating system, we offer an installation service for a warm air duct through a ventilation plate. The improved new control unit is also available separately.  https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Webasto pipe connector / double socket, with 60 mm connection Warm air pipe connector for effective distribution of warm air. The warm air pipe connector can be used to connect two warm air pipes with each other. Diameter: Ø 60 mmPrice per piece

Autoterm Push Control S and L The Autoterm Push Control is a compact and easy-to-use switch for controlling Autoterm parking heaters. It enables different operating modes and functions depending on the heater. It also fulfils a long-held customer wish to be able to connect two control units to one heater - so the heater can be started conveniently from the driver's cab, for example, while the standard control unit is installed in the living area. NEW: The Autoterm Push Control enables simple control of air and water level heaters and, for the first time, the option of connecting two control panels to one heater! FunctionsOperating modes for air heatersPower mode (standard mode): With a single or multiple click, you can choose between five fixed power levels. The colour of the LED ring indicates which power level the heater is currently inTemperature mode: In conjunction with an external temperature sensor, a temperature of 18, 21 or 25 degrees can be achieved and maintained. "Maximum power" can also be set as the highest level in temperature mode. Operating modes for water level heatersPreheating mode: The heater runs until a certain coolant temperature is reached, then switches off the burner and restarts when the temperature drops. Here you can choose between a heating time limited to two hours or continuous operation. Simple installationThe Push Control comes in a plug-and-play design with an included control module and connection cable for quick and easy integration. Dual controlfinally possible: The Push Control can be used as the sole control element for your heating system or combined with the Autoterm Comfort Control control panel to enable dual control for a single heating system. This makes it easy to operate your parking heater in different areas of the vehicle and ensures maximum user comfort. Robust and waterproofStainless steel housing with IP67 protection class, making the switch waterproof and safe and durable even under extreme conditions. CompatibilitySuitable for Autoterm Air heaters (2D, 4D, 8D, 9D) and Autoterm Flow heaters (5D, 5B, 14D). Available in two versions:Variant S: 6 mm thread with Molex plugVariant L: 12 mm thread with round plugDimensions for both switches:Diameter of the button surface 25 mm each.Thread diameter 22 mm each.  

Installation service for warm air ducts for ventilation plates for all models The installation of the warm air duct is carried out at the specified fixed price, regardless of the duration.   Please note: The price refers only to the installation flat rate, including the required plastic conduit. The ventilation plates must be purchased separately.   Depending on whether you want to conduct heat from an external mobile heating box into the interior of the vehicle or from the interior of the vehicle via a permanently installed auxiliary heating system into, for example, a roof tent, you can purchase the following items from us:   Ventilation plates for a wide range of vehicles can be found here. Waluflex warm air pipe End piece for Waluflex warm air hose Permanently installed auxiliary heaters can be found here. Mobile auxiliary heater boxes can be found here.   Please note that built-in wind deflectors may need to be removed when installing a warm air duct through a ventilation grille.   When ordering, please provide your telephone number so that we can arrange an appointment. Installation is only possible on site in Berg near Neumarkt (postcode: 92348).   If you order the flat rate together with the appropriate ventilation plate, the item can also be shipped. If you already have ventilation plates, we can perform the installation service by appointment.