Das könnte Sie auch interessieren
Cable winch set for Toyota Hilux incl. 4.3 to tractive force cable winch 12V from 2016 onwards A cable winch system was designed for the Toyota Hilux, which is mounted behind the front cover of the vehicle. This system is ideal for use in rough terrain. In the design, particular attention was paid to minimising the load on the vehicle's own axle in the event of a self-recovery. Technical data: Transmission 3-stage planetary gear max. Tractive force 4300 kg max. Pulling speed 15 m/min* Motor power 3.8 hp Engine type Series Wound** Reduction ratio 110:1 Max. Power consumption 530 amps Voltage 12 V Rope (∅ x length) 10 mm x 30 m Drum (∅ x length) 63 x 223 mm Overall size (LxWxH) 574 x 160 x 225 mm Weight of cable winch 29.1 kg Weight of installation set 13.6 kg Total weight 42.7 kg Installation time 5 hours Features: Motor IP67 sealed by groove with sealing ring Freewheel lever Stainless steel cross braces Reinforced cable drum Powder-coated aluminium die-cast housing Motor/gearbox Internal drum brake with 3 brake shoes Removable control unit (so that the control unit can be installed as required) Reinforced, powder-coated contactor housing made of deep-drawn sheet metal Scope of delivery: Installation set Cable winch Aluminium cable window Fastening screws Plastic rope with hook Pulley with hook Cable remote control Radio remote control Operating instructions TÜV parts certificate Attention:Please note that our cable winches may only be used for ground pulling and are not suitable for lifting!The operating instructions for the cable winch must be read completely before use and must be strictly followed, otherwise there is a risk of injury!Warranty:Horntools grants a warranty of 3 years on the gear and drum of the cable winch in compliance with the warranty and service regulations.Note:You will find all the important information about handling your new winch in the operating instructions and from your specialist dealer. This winch may generate more noise.
Prices incl. VAT;
SUPERWINCH TIGER SHARK 11.5 The 12 V Superwinch electric winch Tiger Shark 11500 has a two-stage planetary gearbox. The winch is equipped with an automatic load holding brake with mechanical cone brake for large loads and a freewheel clutch for pulling the rope by hand. The Superwinch Tiger Shark 11.5 electric winch has waterproof sealed relays for high electrical currents, allowing longer duty cycles.It is used for commercial recovery of rolling loads.Features: Rope speed: 5.7 - 0.6 [m/min]. Pulling force: 5.2 t Voltage: 12 V Weight: 42 kg Power consumption at full load: 410 A Scope of delivery: 1 x winch optional: 1 x steel cable 9.5 mm/ 25 m or plastic winch cable 10 mm/30 m - optional in orange or grey 1 x winch hook 1 x roller window 1 x relay box 1 x battery cable 1 x cable remote control
Prices incl. VAT;
SUPERWINCH SX 10SR The 12 V Superwinch electric winch SX 10 SR has a three-stage planetary gear. The winch is equipped with an automatic load holding brake with mechanical cone brake for large loads and a freewheel clutch for pulling off the rope by hand. The Superwinch electric winch SX 10 SR has waterproof sealed relays for high electrical currents, which allow a longer duty cycle. The rope drum has a patented lighting system. It is used for commercial recovery of rolling loads.Features:Rope speed: 8.3 - 1.4 [m/min].Pulling force: 4.5 tVoltage: 12 VWeight: 61 kgPower consumption at full load: 363 AMovable control boxScope of delivery: 1 x cable winch 1 x synthetic fibre rope 9.5 mm/ 24 m 1 x cable mouth 1 x relay box 1 x battery cable 1 x cable remote control 1 x radio remote control
Prices incl. VAT;
SUPERWINCH SX 12SR The 12 V Superwinch electric winch SX 10 SR has a three-stage planetary gear. The winch is equipped with an automatic load holding brake with mechanical cone brake for large loads and a freewheel clutch for pulling off the rope by hand. The Superwinch electric winch SX 10 SR has waterproof sealed relays for high electrical currents, which allow a longer duty cycle. The cable drum has a patented lighting system.The winch is used for commercial recovery of rolling loads and other applications.Equipment:Rope speed: 7.1 - 1.1 [m/min].Pulling force: 5.4 tVoltage: 12 VWeight: 31 kgPower consumption at full load: 379 AMovable control boxScope of delivery: 1 x cable winch 1 x synthetic fibre rope 9.5 mm/ 24 m 1 x cable mouth 1 x relay box 1 x battery cable 1 x cable remote control 1 x radio remote control
Prices incl. VAT;
Nakatanenga winch bundle Tigershark 9.5 or 11.5 for Land Rover Defender In the Nakatanenga winch bundle for the Land Rover Defender, you get everything you need for safe and reliable self or third-party recovery:The basis is the proven Nakatanenga NAWIBU2 winch bumper, which is equally suitable for Defender with or without air conditioning. The bumper, which is manufactured locally for us, is powder-coated black and reliably protects the front of the vehicle even during tough off-road use. The raised corners of the bumper improve the vehicle's slope angle. The two integrated, swivelling recovery eyes are ideal for self-recovery and recovery by others - or for hooking in the pulley, which is also supplied and doubles the pulling force of the winch or makes difficult recoveries possible in the first place. The design of the winch bumper allows for easy registration by means of a fee-based individual approval.There is the optional possibility of mounting two 70 mm spotlights recessed - so they are optimally protected against damage in the terrain. We use modern LED driving lights from Nolden, which provide excellent light with low power consumption (only 1.1 A per headlight). They have an E-mark and can therefore be used without registration. In order to harmonise with any existing Nolden Bi-LED main headlights, the auxiliary driving lamps are available in black or chrome-coloured optics. The 12 V Superwinch electric winch Tiger Shark 11500 / 9500 has a two-stage planetary gearbox. The winch is equipped with an automatic load holding brake with mechanical cone brake for large loads and a freewheel clutch for pulling the rope by hand. The Superwinch Tiger Shark 11.5 / 9.5 electric winch has waterproof sealed relays for high electrical currents, allowing longer duty cycles.It is used for commercial recovery of rolling loads. Technical data of the Tigershark 9.5 winch: Rope speed: 5.7 - 1.2 [m/min].Pulling force: 4.3 tVoltage: 12 VWeight: 41 kgPower consumption at full load: 340 A Technical data of the Tigershark 11.5 winch: Rope speed: 5.7 - 0.6 [m/min].Pulling force: 5.2 tVoltage: 12 VWeight: 42 kgPower consumption at full load: 410 A The winches have a synthetic fibre rope made of high-strength fibre instead of the conventional steel rope. This is not only much lighter (and thus benefits the handling and efficiency of the vehicle), but also much safer to use. In the event of tearing, it does not become a dangerous projectile - rather, it simply falls to the ground. In fact, it is so light that it floats! It also drastically reduces the risk of injury from protruding strand ends. The flat Nakatanenga rope window again saves weight compared to conventional roller rope windows, is gentler on the rope and protrudes less.Depending on the vehicle version and winch type, it may be necessary to adapt the radiator grille.The winch bundle is rounded off by a useful accessory bag containing a high-strength tree anchor strap, two shackles, the above-mentioned pulley and a pair of Nakatanenga work gloves. Bundle consisting of: 1x cable winch Tigershark 9.5 or 11.5 - please select the appropriate version1x cable remote control1 x Nakatanenga winch window1 x plastic winch cable - either in orange or grey1 x accessory bag for plastic winch cable1 x winch bumper - optionally: without headlights, with 70mm Nolden spotlights black, with 70mm Nolden spotlights chrome1 x cable set for winch mounting1 x winch hook XL The cable winch bundle does not come with an ABE or expert opinion for the bumper. Registration as an "equipment carrier cable winch" is possible at numerous test centres without any problems by means of individual acceptance for which a charge is made. We recommend prior consultation with the local, authorised test engineer - or alternatively registration in our company. For this purpose, we require the vehicle with mounted bumper incl. cable winch on site. You can also mount the bumper yourself - we will then take care of the registration! We will charge you for the TÜV fees - according to our experience 100-150 EUR - as well as the working time of approx. 1 hour.Please also note our installation flat rate! If you add this to your shopping basket during the order process and send it off, we will contact you to arrange an appointment - please note that we have several weeks' lead time for workshop appointments!For the care of the plastic winch rope and to extend its service life, we recommend the appropriate impregnation spray. For intensive and frequent use of the winch, we recommend the use of the Nakatanenga double battery system with 160Ah total capacity.
Prices incl. VAT;
Nakatanenga winch bundle SX 10SR or SX 12SR for Land Rover Defender In the Nakatanenga winch bundle for the Land Rover Defender, you get everything you need for safe and reliable self or third-party recovery:The basis is the proven Nakatanenga NAWIBU2 winch bumper, which is equally suitable for Defender with or without air conditioning. The bumper, which is manufactured locally for us, is powder-coated black and reliably protects the front of the vehicle even during tough off-road use. The raised corners of the bumper improve the vehicle's slope angle. The two integrated, swivelling recovery eyes are ideal for self-recovery and recovery by others - or for hooking in the pulley, which is also supplied and doubles the pulling force of the winch or makes difficult recoveries possible in the first place. The design of the winch bumper allows for easy registration by means of a fee-based individual approval.There is the optional possibility of mounting two 70 mm spotlights recessed - so they are optimally protected against damage in the terrain. We use modern LED driving lights from Nolden, which provide excellent light with low power consumption (only 1.1 A per headlight). They have an E-mark and can therefore be used without registration. In order to harmonise with any existing Nolden Bi-LED main headlights, the auxiliary driving lamps are available in black or chrome-coloured optics. The 12 V Superwinch electric winch SX 10 SR or SX 12SR has a three-stage planetary gear. The winch is equipped with an automatic load holding brake with mechanical cone brake for large loads and a freewheel clutch for pulling off the rope by hand. The Superwinch electric winch SX 10 SR or SX 12SR has waterproof sealed relays for high electrical currents, which allow a longer duty cycle. The rope drum has a patented lighting system. It is used for commercial recovery of rolling loads. The winches have a synthetic fibre rope made of high-strength fibre instead of the conventional steel rope. This is not only much lighter (and thus benefits the handling and efficiency of the vehicle), but also much safer to use. In the event of tearing, it does not become a dangerous projectile - rather, it simply falls to the ground. In fact, it is so light that it floats! It also drastically reduces the risk of injury from protruding strand ends. The flat Nakatanenga rope window again saves weight compared to conventional roller rope windows, is gentler on the rope and protrudes less.Depending on the vehicle version and winch type, it may be necessary to adapt the radiator grille.The winch bundle is rounded off by a useful accessory bag containing a high-strength tree anchor strap, two shackles, the above-mentioned pulley and a pair of Nakatanenga work gloves. Technical data of the Superwinch SX 10SR winch: Rope speed: 8.3 - 1.4 [m/min].Pulling force: 4.5 tVoltage: 12 VWeight: 61 kgPower consumption at full load: 363 AMovable control box Technical data of the Superwinch SX 12SR cable winch: Rope speed: 7.1 - 1.1 [m/min].Pulling force: 5.4 tVoltage: 12 VWeight: 31 kgPower consumption at full load: 379 AMovable control box The cable winch bundle does not come with an ABE or expert opinion for the bumper. Registration as an "equipment carrier cable winch" is possible at numerous test centres without any problems by means of individual acceptance for which a charge is made. We recommend prior consultation with the local, authorised test engineer - or alternatively registration in our company. For this purpose, we require the vehicle with mounted bumper incl. cable winch on site. You can also mount the bumper yourself - we will then take care of the registration! We will charge you for the TÜV fees - according to our experience 100-150 EUR - as well as the working time of approx. 1 hour.Please also note our installation flat rate! If you add this to your shopping basket during the order process and send it off, we will contact you to arrange an appointment - please note that we have several weeks' lead time for workshop appointments!For the care of the plastic winch rope and to extend its service life, we recommend the appropriate impregnation spray. For intensive and frequent use of the winch, we recommend the use of the Nakatanenga double battery system with 160Ah total capacity. Bundle consisting of: 1x Superwinch SX10 SR or SX 12SR cable winch - please select the appropriate variant1x cable remote control1 x Nakatanenga winch window1 x plastic winch cable - optionally in orange or grey1 x accessory bag for plastic winch cable1 x winch bumper - optionally: without headlights, with 70mm Nolden spotlights black, with 70mm Nolden spotlights chrome1 x cable set for winch mounting1 x winch hook XL
Prices incl. VAT;
SUPERWINCH SX 10SR black The 12 V Superwinch electric winch SX 10 SR has a three-stage planetary gear.The winch is equipped with an automatic load holding brake with mechanical cone brake for large loads and a freewheel clutch for pulling off the rope by hand. The Superwinch electric winch SX 10 SR has waterproof sealed relays for high electrical currents, which allow a longer duty cycle. The rope drum has a patented lighting system.It is used for commercial recovery of rolling loads.Features:Rope speed: 8.3 - 1.4 [m/min].Pulling force: 4.5 tVoltage: 12 VWeight: 61 kgPower consumption at full load: 363 AMovable control boxScope of delivery: 1 x cable winch black 1 x synthetic fibre rope 9.5 mm/ 24 m 1 x cable mouth 1 x relay box 1 x battery cable 1 x cable remote control 1 x radio remote control
Prices incl. VAT;
SUPERWINCH SX 12SR black The 12 V Superwinch electric winch SX 10 SR has a three-stage planetary gear.The winch is equipped with an automatic load holding brake with mechanical cone brake for large loads and a freewheel clutch for pulling off the rope by hand. The Superwinch electric winch SX 10 SR has waterproof sealed relays for high electrical currents, which allow a longer duty cycle. The cable drum has a patented lighting system.The winch is used for commercial recovery of rolling loads and other applications.Equipment:Rope speed: 7.1 - 1.1 [m/min].Pulling force: 5.4 tVoltage: 12 VWeight: 31 kgPower consumption at full load: 379 AMovable control boxScope of delivery: 1 x cable winch black 1 x synthetic fibre rope 9.5 mm/ 24 m 1 x cable mouth 1 x relay box 1 x battery cable 1 x cable remote control 1 x radio remote control
Prices incl. VAT;
Durable and reliable: cable winch with maintenance-free gear brake In contrast to its predecessor, this model has a gear brake instead of a drum brake. The gear brake does not wear out compared to the drum brake and loses no braking effect when used for a long time. The cable winch has a 3-year guarantee, but with the right care can give you a lifetime of pleasure. Furnishing: Remote control 1x cable 1x radio integrated (delivered without battery)Synthetic winch rope - optionally in gray or orangePotted reinforced relay (contactor) waterproofstable powder-coated contactor housing made of deep-drawn sheet metalMotor & gearbox IP67 sealed by groove with sealing ringremovable control unit (so that the control can be installed as desired)Freewheel lever * gear neutral position made of stainless steelCross struts and equipment made of stainless steelreinforced rope drum ** (suitable for use with plastic ropes)powder-coated aluminium die-cast housing motor / gearboxtransmission brakeCable length: 1.6 mCable cross-section: 35 mm²3 year guaranteeoperation manual * A freewheel lever is used to decouple the gearbox and to unwind the winch quickly by hand. ** Plastic cables load the cable drums laterally by far more than steel cables Technical specifications: Working range voltage: 10-16 VoltMax. Power consumption 530 Amp **Train speed free of load 17 m / minuteTraction 4,300 kg **3-stage planetary gear 108: 1 geared downNet weight: 30 kg without rope and rope window4.6 KW Series Wound Motor *Drum (ØxLength): 63x216 mmOverall size (LxWxH): 612 x 160 x 270 mm * Series motor with electrically generated magnetic field power = with a standard 70 AH battery** Values can vary considerably, depending on the battery system, the winch can pull up to twice, the traction is designed for a standard 70 AH battery. With more powerful battery systems the pulling power must be limited by the current / voltage. Material The cable winch is made of aluminum and high-strength stainless steel. High strength so that the steel can withstand the loads. This steel can also oxidize, i.e. if the parts are exposed to salt in winter, you should care for them every now and then and let them in with a thin oil film. We have provided maintenance instructions in the download area. The pulling force of the winch is highest on the first or lowest rope layer on the drum. Similar to a bicycle gear shift. The less rope there is on the drum, the slower the winch pulls and the more power it has. Cable layer tensile speed1 4,300 kg 15 m / min2 3,500 kg 18 m / min3 2,950 kg 22 m / min4 2,550 kg 26 m / min Scope of delivery:1 x winch1 x winch rope - optionally in orange or gray1 x winch window1 x winch hook
Prices incl. VAT;
The Power Winch System Beta for the Suzuki Jimny The winch system was developed especially for the Suzuki Jimny and fits very well into its front. It is mounted on the original points of the vehicle. The Alpha 9.5 winch was developed especially for users who have little space available. Despite its compact design, the winch has a pulling force of 4.3 tonnes. Technical data: Gearbox: 3-stage planetary gearMax. Pulling force: 4,300 kgMax. Pulling speed: 7 m/min*Engine power: 3.7 hpEngine type: Series Wound**Reduction ratio 230:1Max. Power consumption: 365 ampsVoltage: 12 VRope (∅ x length): 8 mm x 30 mDrum (∅ x length): 63 x 120 mmOverall size (LxWxH): 437 x 160 x 250 mmWeight cable winch: 22.5 kgInstallation time: 4 hours Features: Motor IP67 sealed by groove with sealing ringFreewheel leverStainless steel cross bracesReinforced cable drumPowder-coated aluminium die-cast housing Motor/gearboxInternal drum brake with 3 brake shoesRemovable control unit (so that the control unit can be installed as required)Reinforced, powder-coated contactor housing made of deep-drawn sheet metal Scope of delivery: Installation set Cable winch Aluminium cable window Fastening screws Plastic rope with hook Pulley with hook Cable remote control Radio remote control Operating instructions TÜV parts certificate Attention:Please note that our cable winches may only be used for ground pulling and are not suitable for lifting!The operating instructions for the cable winch must be read completely before use and must be strictly followed, otherwise there is a risk of injury!Warranty:We grant a warranty of 3 years on the gear and drum of the cable winch in compliance with the warranty and service regulations.Note:You will find all the important information about handling your new winch in the operating instructions and from your specialist dealer.This winch may generate more noise.
Prices incl. VAT;
Ähnliche Artikel
The Horntools Alpha 12.0 Super Speed Edition With its low weight and compact dimensions, it is perfectly suitable for vehicles with a total weight of up to 4 tons. Furnishing: 9.2 mm Ø galvanized steel cable with 28 m length with hook INFO: Steel rope is included separately in the scope of delivery stainless steel roller rope window remote control 1x cable 1x radio integrated (delivered without battery) potted reinforced relay (contactor) waterproof motor IP67 sealed by groove with sealing ring removable control unit (so that the control can be installed as desired) freewheel lever * gear neutral position made of stainless steel cross braces made of stainless steel reinforced rope drum ** (suitable for use with plastic rope) powder-coated aluminum die-cast housing, motor / gearbox reinforced contactor housing made of deep-drawn sheet metal, powder-coated internal drum brake with 3 brake shoes cable length: 1.7 m cable cross section: 50 mm² 3 year guarantee operation manual * A freewheel lever is used to decouple the gearbox to quickly unwind the winch by hand. Technical specifications: working range voltage: 10-16 Volt max. Power consumption 600 A ** train speed free of load 11 m / minute traction 5,400 kg ** 3-stage planetary gear 110: 1 geared down net weight: 25.8 kg without rope and rope window Series wound motor * drum (ØxLength): 63x226 mm overall size (LxWxH): 577 x 160 x 225 mm * Series motor with an electrically generated magnetic field** Values can vary considerably, depending on the battery system, the winch can pull up to twice, the traction is designed for a standard 70 AH battery. With more powerful battery systems, the pulling power must be limited by the current / voltage.
Prices incl. VAT;
The Horntools Alpha 9.5 With its low weight and compact dimensions, it is perfect for vehicles with a total weight of up to 3.5 tons. Especially for touring vehicles that are fully equipped, the winch should not have too much weight, but still have to do great things. Furnishing: 9.2 mm Ø galvanized steel cable with 26 m length with hook INFO: steel cable is included separately in the scope of delivery stainless steel roller rope window remote control 1x cable potted reinforced relay (contactor) waterproof motor IP67 sealed by groove with sealing ring removable control unit (so that the control can be installed as desired) freewheel lever * gear neutral position made of stainless steel cross braces made of stainless steel reinforced rope drum ** (suitable for use with plastic rope) powder-coated aluminum die-cast housing, motor / gearbox reinforced contactor housing made of deep-drawn sheet metal, powder-coated internal drum brake with 3 brake shoes cable length: 1.4 m cable cross section: 35 mm² 3-year warranty - this warranty exists independently of the existing gratuitous statutory rights for defects. The statutory rights in respect of defects are not restricted by this guarantee. Operating instructions * A freewheel lever is used to decouple the gearbox to quickly unwind the winch by hand. Technical specifications: working range voltage: 10-16 Volt max. Power consumption 365 Amp ** train speed free of load 7m / minute traction 4,300 kg ** 3-stage planetary gear 230: 1 geared down gross weight: 40 kg net weight: 32.3 kg weight with steel cable and roller cable window: 37.5kg Series wound motor * drum (ØxLength): 63 x 226 mm overall size (LxWxH): 577 x 160 x 225mm * Series motor with an electrically generated magnetic field** Values can vary considerably, depending on the battery system, the winch can pull up to twice, the traction is designed for a standard 70AH battery. With more powerful battery systems, the pulling power must be limited by the current / voltage.
Prices incl. VAT;
The Alpha 12.0 Super Speed Edition Technical data of the winch:- Working range voltage: 10-16Volt- Max. Power consumption 600A **- Train speed free of load 11m / minute- traction 5400kg **- 3-stage planetary gear 110: 1 geared down- Net weight: 25.8kg without rope and rope window- Series wound motor *- Drum (ØxLength): 63x226mm- Overall size (LxWxH): 577 x 160 x 225mm* Series motor with an electrically generated magnetic field** Values can vary considerably, depending on the battery system, the winch can pull up to twice, the traction is designed for a standard 70AH battery. With more powerful battery systems, the pulling power must be limited by the current / voltage.The bundle consists of:1x horntools Alpha 12.0 electric winch with 5.4 tons traction1x Nakatanenga winch window1x winch hook1x winch rope (optionally in gray or orange)Please note that the depicted steel cable, the winch window and the winch hook from Superwinch are NOT included in the scope of delivery.
Prices incl. VAT;
Technical data of the rope winch Alpha 9.5 - Working range voltage: 10-16Volt- Max. Power consumption 365A **- Train speed free of load 7m / minute- traction 4300kg **- 3-stage planetary gear 230: 1 geared down- Gross weight: 40kg- Net weight: 32.3kg- Weight with steel cable and roller cable window: 37.5kg- Series wound motor *- Drum (ØxLength): 63x226mm- Overall size (LxWxH): 577 x 160 x 225mm* Series motor with an electrically generated magnetic field** Values can vary considerably, depending on the battery system, the winch can pull up to twice, the traction is designed for a standard 70AH battery. With more powerful battery systems, the pulling power must be limited by the current / voltage.The bundle consists of:1x horntools Alpha 9.5 electric winch with 4.3 tons traction1x Nakatanenga winch window1x winch hook1x winch rope (optionally in gray or orange)Please note that the depicted steel cable, the winch window and the winch hook from Superwinch are NOT included in the scope of delivery.
Prices incl. VAT;
Bundle with Horntools Alpha winch incl. recovery accessories In the Nakatanenga winch bundle for the Land Rover Defender, you get everything you need for safe and reliable self or third-party recovery: The basis is the proven Nakatanenga NAWIBU2 winch bumper, which is equally suitable for Defender with or without air conditioning. The bumper, which is manufactured locally for us, is powder-coated black and reliably protects the front of the vehicle even during tough off-road use. The raised corners of the bumper improve the vehicle's slope angle. The two integrated, swivelling recovery eyes are ideal for self-recovery and recovery by others - or for hooking in the pulley, which is also supplied and doubles the pulling force of the winch or makes difficult recoveries possible in the first place. The design of the winch bumper allows for easy registration by means of a fee-based individual approval.There is the optional possibility of mounting two 70 mm spotlights recessed - so they are optimally protected against damage in the terrain. We use modern LED driving lights from Nolden, which provide excellent light with low power consumption (only 1.1 A per headlight). They have an E-mark and can therefore be used without registration. In order to harmonise with any existing Nolden Bi-LED main headlights, the auxiliary driving lamps are available in black or chrome-coloured optics.Instead of the conventional steel cable, the winches have a synthetic fibre cable made of high-strength fibre. This is not only significantly lighter (and thus benefits the handling and efficiency of the vehicle), but also much safer to use. In the event of tearing, it does not become a dangerous projectile - rather, it simply falls to the ground. In fact, it is so light that it floats! It also drastically reduces the risk of injury from protruding strand ends. The flat Nakatanenga rope window again saves weight compared to conventional roller rope windows, is gentler on the rope and protrudes less. Depending on the vehicle version and winch type, it may be necessary to adapt the radiator grille.The winch bundle is rounded off by a useful accessory bag containing a high-strength tree anchor strap, two shackles, the above-mentioned pulley and a pair of Nakatanenga work gloves. Technical data winch Horntools Alpha 9.5 - Working range voltage: 10-16 Volt- Max. Power consumption 365 Amp **- Train speed free of load 7 m / minute- Traction 4,300 kg **- 3-stage planetary gear 230:1 geared down- Gross weight: 40 kg- Net weight: 32.3 kg- Weight with steel cable and roller cable window: 37.5 kg- Series wound motor *- Drum (ØxLength): 63x226 mm- Overall size (LxWxH): 577 x 160 x 225 mm Technical data winch Horntools Alpha 12.0:- Working range voltage: 10-16 Volt- Max. Power consumption 600 A **- Train speed free of load 11 m / minute- Traction 5,400 kg **- 3-stage planetary gear 110: 1 geared down- Net weight: 25.8 kg without rope and rope window- Series wound motor *- Drum (ØxLength): 63x226 mm- Overall size (LxWxH): 577 x 160 x 225 mm * Series motor with an electrically generated magnetic field ** Values can vary considerably, depending on the battery system, the winch can pull up to twice, the traction is designed for a standard 70AH battery. With more powerful battery systems, the pulling power must be limited by the current / voltage. Depending on the vehicle version and winch type, it may be necessary to adapt the radiator grille. Bundle consisting of: 1 x winch Horntools Alpha 9.5 or Alpha 12.0 - please select the appropriate variant1 x Nakatanenga winch window1 x plastic winch cable - either in orange or grey1 x accessory bag for plastic winch cable1 x winch bumper - optionally: without headlights, with 70mm Nolden high-beam headlights black, with 70mm Nolden high-beam headlights chrome1 x cable set for winch mounting1 x winch hook XL The cable winch bundle does not come with an ABE or expert opinion for the bumper. Registration as an "equipment carrier winch" is possible at numerous test centres without any problems by means of an individual acceptance for which a fee is charged. We recommend prior consultation with the local, authorised test engineer - or alternatively registration in our company. For this purpose, we require the vehicle with mounted bumper incl. cable winch on site. You can also mount the bumper yourself - we will then take care of the registration! We will charge you for the TÜV fees - from experience 100-150 EUR - as well as the working time of approx. 1 hour.Please also note our installation flat rate! If you add this to your shopping basket during the order process and send it off, we will contact you to arrange an appointment - please note that we have several weeks' lead time for workshop appointments!For the care of the plastic winch rope and to extend its service life, we recommend the appropriate LUBI-FILL impregnation spray. For intensive and frequent use of the winch, we recommend the use of the Nakatanenga double battery system with 160Ah total capacity.
Prices incl. VAT;
Mesh carrying bag for mountain ropes Our robust and easy-to-clean Polyester mesh bag was initially developed by our Nakatanenga textile shop to hold the kinetic tow ropes. The big Kinto rope with 8 m length and 24 mm width fits perfectly into this 60 x 35 cm bag. Apart from the ropes, this mesh bag is absolutely perfect for everything else that comes dirty and dripping: sports shoes and hiking boots, rain gear, training equipment, water sports, you name it. Using mesh as the primary material for bag, also means much nicer handling in comparison to ordinary closed materials. You can quickly pack wet and dirty ropes and let them drain and dry in the bag. That way, there is no chance for trapped moisture to contribute to any material deterioration and unpleasant moldy smells. You can also use the mesh itself to grab and handle excessively dirty equipment without having to use your bare hands, if nothing else is available. That comes in especially handy in emergency recoveries on the road, because you’re never as likely to carry all the dirt into your car’s interior. After the job is done, you can easily hose down the rope within the bag. Robust seams, a quality zipper, wrap-around handles and two orange loops for hanging or securing make this mesh bag one tough and durable receptacle for all your rough gear. Material: Polyester - washable up to 30° Dimensions: Width 60 cm Height 35 cm MADE IN EU
Prices incl. VAT;
Accessory kit for winches Whether as an accessories kit for winching enthusiasts or as handy emergency pack on overlanding trips, our Nakatanenga winching packages contain everything you need when you’re stuck in a rut. You have the choice between a steel version, primarily for steel cables, or the lightweight pack made from synthetics and aluminum, exclusively designed for synthetic winch ropes. Both varieties basically consist of the same components: two recovery straps, a pulley or block, shackles, protective gloves and a bag. The steel rope kit contains two steel shackles, a foldable snatch block with a work load WLL of 3.5 tons and a shoulder bag made from 100 % cotton. The synthetic kit boasts an NMP pulley made from Eloxal coated aluminum, three soft shackles and the Nakatanenga tool bag coated in robust and waterresistant Nylon PU. Straps Key items in the accessory kits are two 77 mm wide, high quality recovery straps. Made from polyamides, these straps come in lengths of 2 and 8 m and have a breaking strength of up to 9 tons. By design, the short strap is also a perfect tree trunk protector. FYI: The long strap is a new addition to the steel set and does not fit the cotton bag. It has to be stored separately. Shackles The recovery straps feature end loops strengthened by machine sewn Polyester coats. The 10 mm soft shackles in orange or gray are fixed through these end loops or “eyes”. The kit contains two soft shackles for this purpose and another one to fix the NMP block. The synthetic shackles are ultra-light and with a breaking strength of up to 12 t extremely loadable. As always, synthetics means little danger of injury, easy handling, no corrosion and no damaging of vehicle and equipment. The steel kit on the other hand uses traditional steel shackles with screw bolts. Pulleys The pulleys or blocks in the two kits differ considerably in design, material and usage. In the synthetics kit, the NMP block made from hard, Eloxal coated aluminum is fixed by a soft shackle and is exclusively meant to be used with plastic winch ropes of 8 to 14 mm thickness. Produced to military standards, this block has a breaking strength of 18 t and weighs only 1.65 kg. WARNING: Again, the NMP pulley must not be used with steel cables. If you are using steel cables, please choose the other kit with the metal snatch block. Our construction of high-strength 6 mm galvanised steel and a 15 mm polymer pulley accepts any type of mountain rope between 8 - 13 mm: Synthetic, plasma and steel ropes.The working load of the pulley is 9,000 lbs or just over 4 t, the breaking load is 19,300 lbs or over 8.7 t and is best suited for steel ropes. Bags The synthetics kit comes in our robust, high quality Nakatanenga tool bag. It’s flexible, very lightweight and uses just as much storage space as the actual contents. That makes it ideal for quick, compact packing and easy transport of all your winching and recovery equipment. Shackles and smaller item fit into separate pockets inside. The steel kit can be stowed in the cotton shoulder bag, with the exception of the long strap. Gloves Last but not least, both sets come with a pair of protective gloves, made from elastic synthetic materials. These sturdy gloves feature grippy Almara plastic leather in the palm area and are not available separately, unlike the rest of the contents.
Prices incl. VAT;
Robust Winch Hook from Nakatanenga: 2000kg Load Capacity for 7-8mm Steel Cables – Safety in Every Recovery In demanding off-road use, forestry work, or agriculture, reliable recovery equipment is essential. A critical component of every winch is the winch hook, which establishes the connection between the winch and the anchor point. The Nakatanenga winch hook, with an impressive load capacity of 2000kg and specifically designed for steel cables with a diameter of 7-8mm, offers the safety and robustness you need in critical situations. High Load Capacity for Demanding Tasks With a maximum pulling load of 2000 kilograms (equivalent to 2 tons), this winch hook is a real powerhouse. It is designed to reliably withstand even demanding recovery operations or heavy pulling tasks. This high load capacity makes it a versatile tool for a wide range of vehicles and winches operating within the specified cable diameter range. Optimized for 7-8mm Steel Cables The specific design for steel cables with a diameter of 7 to 8 millimeters ensures an optimal fit and power transmission. This is crucial to ensure a secure and positive connection between the cable and the hook. Correct sizing also prevents unnecessary wear on the cable and the hook itself, thus contributing to the longevity of your entire winch setup. Robust Construction for Maximum Durability Made from high-quality, durable material, the Nakatanenga winch hook is designed to withstand the highest loads and harsh off-road conditions. The robust construction ensures a long service life, even with regular use in adverse weather conditions, mud, or contact with stones. A resistant surface coating also effectively protects against corrosion. Safety First – The Integrated Safety Latch An indispensable feature of this winch hook is the integrated safety latch (also known as a safety catch or gate). This mechanism reliably prevents the unintentional unhooking of the cable, recovery strap, or anchor point during winching operations. This is a crucial safety factor that minimizes the risk of accidents and enables a controlled recovery process. Versatile Applications Although perfect for off-road vehicle recovery, this winch hook also finds application in other areas. In forestry for skidding logs, in agriculture for pulling tasks, or for general tasks requiring the use of a winch with a 7-8mm steel cable, this hook provides valuable service. Nakatanenga – Quality You Can Rely On Nakatanenga stands for field-tested and durable off-road equipment. This winch hook seamlessly fits into this quality promise and has been developed to meet the high demands of off-road enthusiasts and professional users. The Nakatanenga winch hook with a 2000kg load capacity for 7-8mm steel cables is more than just a connecting piece. It is a guarantee for safety, reliability, and durability in all your winching operations. Invest in quality that pays off in the decisive moment and equip your winch with this robust hook from the Nakatanenga off-road shop.
Prices incl. VAT;
winch hook XL / XXL
€95.00
Prices incl. VAT; / Parcel shipping
↪️ demountable winch hook for plastic and steel cables ✔️ for winches up to 10,000 lbs or 18,000 lbs pulling force ✔️ best quality ✔️ fast shipping
Winch hook XL white / XXL white
Often little attention is paid to an important detail on the winch: the hook. It is of crucial importance for the transmission of power between the winch and the anchorage point and must also be able to be operated safely in stressful situations.
We offer two models from the industrial sector that shine with convincing detailed solutions:
- large radius of the hook so that even double straps can be securely hooked in twice
- large opening of the hook, it can be placed around most towbars
- stable cast iron snap (not made of thin sheet metal) that closes securely
- can be dismantled, thus simple assembly / disassembly of the rope without splicing, e.g. easy cleaning of the plastic rope possible
- large radius of the rope holder, so ropes with a large diameter and / or rope thimble can be used
Actual weight (XL): 0.750 kg
Actual weight (XXL): 1.445 kg
While the smaller model XL is designed for winches up to 10,000 lbs traction, the XXL models can be equipped with winches up to 18,000 lbs traction. The minimum breaking load is 18.000 kg or 32.600 kg. The hooks are made of alloyed, tempered steel, grade 8 and are painted. They are suitable for steel and plastic ropes with or without a thimble, the ropes can be installed without splicing.
Please select the model.
Please note:
The delivered color may differ from the pictures.