Sample fabrics roof tent 2025/'26: Are you not quite sure whether the tent fabric or its colour is right for you? Then take advantage of our free sample service - free shipping and no minimum order value within Germany.Which fabric is which? Format of the free fabric samples: approx. 5 cm x 5 cm each. Black mesh: Mosquito net Light beige fabric: Awning 102 g/m² -> Roof Lodge Lightweight roof tentDark olive fabric: Tent fabric 102 g/m² -> Roof Lodge Lightweight roof tent Dark blue fabric: Tent fabric 320 g/m² -> Roof Lodge Evolution2 roof tentCoyote fabric: 320 g/m² tent fabric -> Roof Lodge Evolution2 roof tentStone grey fabric, metal-coated on one side: Awning 280 g/m² -> Roof Lodge Evolution2 roof tentPVC clear: Windows (Please note: PVC should never be treated with alcohol or alcohol-based cleaners! Only use clear water or a cleaner approved for PVC for this purpose)TPU kaki: Roof tent canopy (2021; on request)PVC black: Roof tent cover (2023/'24) - not included in the booklet! Tent skin of the lightweight tent made of 100% Oxford nylon with ripstop, an extremely strong but amazingly light material weighing just 102 g/m². Compared to the 320 g/m² fabric of our Evolution 2, this is a reduction of a whopping 78%.  The tent skin and the awning of the Lightweight are identical in terms of fabric, PU-coated on the inside and waterproofed on the outside. This means that no compromises are made in terms of wind and rain protection.

Sense and purpose of an awning compact extension? Glare protection when the sun is low in the skyThe compact extension was developed directly from practical requirements - a nice formulation that in itself means nothing more than: "We were so annoyed and dazzled by the low sun one fine day that we wanted to remedy the situation." And already the initial question is actually fully answered. But that would only be half the truth. On the following picture you can see an awning without extension shown above: As the sun sinks (the same applies in the morning, of course - but for the sake of clarity we will limit ourselves here to the afternoon or evening situation), the light falls further and further under the awning. At a certain position of the sun, the light/shadow dividing line reaches the eye level of a seated person - from now on, the sun can dazzle until it sets. The illustration below shows an awning with a compact extension, which offers several advantages with its angled bracing: When the sun is high, a much larger area is shaded.Only when the sun is setting, the light/shadow dividing line reaches the eye level of a seated person. Here, of course, deviations are possible, since both the slope of the guy, the size of the person and his sitting position are influencing factors.But the most important thing is: You can see what's going on in your surroundings despite the glare shield! If the eyes and the lower edge of the compact extension are on a horizontal plane, then the view would extend exactly to the (ideal) horizon. If you compare that with a moderately braced complete front part, where the view is just between a few centimetres to a few steps - what a difference! What if the sun comes in from the side?Well, then the vehicle will probably have to be moved. But not with our new compact extension. All you have to do is unhinge it from the front, and you can attach it to the side in just a few easy steps. Voilà!But please note: The awnings have a uniform depth of two meters, but differ in their widths. Ideally it hit here all those who have a 200er awning. Owners of a 250 have three options: They simply allow the extension to protrude when used from the side - utility over beauty.You opt for a 200 compact extension - this does not detract from the function.You buy two compact extensions at once - a 250 for the front and a 200 for the side. Feel free to guess what we recommend ;-) Material:Made from our sun sail and awning fabric, a 280 gsm RipStop Polycotton (65% polyester / 35% cotton), metal coated on one side; water and dirt repellent impregnated;due to the comparatively heavy quality, significantly less flutter. Colour: stone grey (taupe)  Our compact extensions are also suitable for use on the awnings of most other manufacturers. The only requirement is a free keder strip in the front profile of the awning or such must be retrofitted.  

Mobile parking heater with aluminum box, various versions Make way, here comes the second generation of our mobile parking heaters in a box! We have packed even more technology, even more experience and even more customer feedback into our new mobile heating boxes. If you are looking for a small, self-sufficient and portable heat source with unrivaled capacity for cold days and nights in unheated outdoor shelters or temporary accommodation, you get everything you need (or want) in a small, weatherproof aluminum box. Available in three modular versions with different configurations, the Nakatanenga heating box provides the perfect, independent heat source for tents, gazebos, garden sheds, mountain huts, snack stands, stalls and much more. The heart of the mobile parking heater is the Autoterm Luft 2D, a diesel-powered air heater with a maximum heat output of 1.8 kW and a diesel consumption of just under a quarter of a liter per hour at full power. With a tank capacity of 18 liters in the twin-tank version, this means that it can heat at full throttle for over 70 hours. The economical unit, which is also very quiet at 55 dB thanks to the exhaust silencer, is controlled by a digital control unit with timer in the version with two batteries and can also be switched on and off by radio remote control. This allows you to preheat your camper, roof tent, caravan or hunting lodge in good time for getting up or for the evening, for example, and operate it from the place where you are staying or sleeping inside*. In contrast to the previous models, the three versions of our mobile parking heater are now only available in one box size, namely 42 liters. This is significantly more compact than the old version in the large version and only slightly more voluminous than the small model from before. What is the advantage? The new universal crate has a modular interior with a powerful performance. Depending on whether you need tanks, batteries or both in the box, you can choose the appropriate version when purchasing: with 9.2 L single or 18.4 L double tank, each without battery, as well as with single tank, two batteries and digital control. However, it can also be easily retrofitted or converted if requirements change. This is made possible by elaborately designed brackets in the box and the use of specially manufactured, made-to-measure tanks.   Features of heating box 1 and 2 (without battery) - USB interface for charging smartphone, power bank, tablet, etc.- Capacity display- PU5 control panel (without timer and storage options)- 12 V connection socket for supplied pole terminal cable- Alternatively, a cable for cigarette lighter (KMSH cable) can be used- 2 radio remote controls- Connection option for external temperature sensor (the connection is inside the box, not outside)”   Features of heater box 3 (with 2 AGM batteries) - USB interface for charging smartphone, power bank, tablet, etc.- Capacity display- Comfort Control control panel (with timer and memory option)- SAE connection socket (suitable for Optimate chargers or Optimate solar charger)- 2 radio remote controls- Connection option for external temperature sensor (the connection is inside the box, not outside)   Equipment of heating box 4 (with 1 LiFePo battery) - USB interface for charging smartphone, power bank, tablet etc.- Capacity display- Comfort Control control panel (with timer and memory option)- SAE connection socket (suitable for Optimate chargers or Optimate solar charger)- 2 radio remote controls- Connection option for external temperature sensor (the connection is inside the box, not outside)-> Please only use LiFePo-compatible chargers Equipment of heating box 5 (with 2 LiFePo batteries) - USB interface for charging smartphone, power bank, tablet, etc.- Capacity display- Comfort Control control panel (with timer and memory option)- SAE connection socket (suitable for Optimate chargers or Optimate solar charger)- 2 radio remote controls- Connection option for external temperature sensor (the connection is inside the box, not outside)”-> please only use LiFePo-compatible chargers The warm air is transported via a firmly screw-fastened, waterproof Flexi hose. As the warm air hose is different for every user and every requirement, we do not include a standard length, but leave it up to you to order the desired length separately here in the store, with or without a silicone sleeve. You can find the perfect storage bag for the Flexi hose here in the store. Regardless of the configuration, the mobile parking heaters are always easy to transport and make the difference between experiencing and suffering in the cold seasons. Whether it's an aurora safari, selling cookies at the Christmas market or winter camping in a roof tent, nothing is really fun if you freeze to death. *ATTENTION: As a precaution, we would like to point out that operation in closed rooms is not permitted due to the risk of poisoning from exhaust fumes. In addition, for optimum heating performance, make sure that the air inlets for combustion and hot air are positioned so that they are protected from the weather. Dimensions Internal dimensions 550x350x220 mm External dimensions 580x380x240 mm Empty weight: 2 tanks, without battery: 18 kg 1 tank, without battery: 16 kg 1 tank, 2 batteries: 36 kg Depending on how many starts are made, the battery lasts at least 40 h, but more likely between 60 and 70 h.  LiFePo4 batteries - i.e. batteries with a lithium iron phosphate cathode - are the ideal supply batteries for camping or electrical work on the move. In contrast to conventional lead-acid AGM technology, lithium batteries combine superior charging properties with much lower weight and volume and a long service life. LiFePo4 batteries can be deep-discharged without any problems, which sooner or later leads to irreparable damage with AGM batteries, as the rule of thumb here is that you should never draw more than 50% charge. If you are not dependent on the greater cold tolerance of AGM batteries, you should definitely consider the higher costs for LiFePo4 batteries and compatible charging technology. The weight and space savings, the long service life and the uncomplicated discharging and charging of the battery are strong arguments in favor of the investment. What's more, LiFePo4 technology is also extremely safe And a special note on aluminum: Although we take the utmost care during storage and shipping, as with all our products, aluminum boxes can always show minimal scratches, stains, dents or other surface features upon delivery. These are material-related and result from the specific properties of the light metal.  In contact with oxygen, aluminum forms a natural, corrosion-protecting patina and is also relatively soft compared to steel, which is three times heavier. This makes the material ideal for use in sheet metal, especially when weight and resistance are important. On the other hand, however, it also means that aluminum can never be completely free of patina or other marks, even on delivery: Small scratches, stains etc. therefore do not constitute grounds for complaint. Ultimately, aluminum boxes are intended to be robust objects of daily use. Like everything that is actively used, they develop an individual patina and every trace of use tells a story. So, have fun with it! If you want to heat the interior of your vehicle, we offer an installation service for warm air ducting through a ventilation plate.   Please note the variants without batteries:  Most portable power stations or battery boxes (such as Goal Zero, Eco Flow, Bluetti etc.) are unfortunately not suitable for operating mobile parking heaters. The heater requires up to 15A as starting current and when shutting down, but very few battery boxes can provide this. Suitable battery boxes for operating the mobile parking heater Please note the legal information on batteries HERE. For certain types of batteries, we are legally obliged to charge a deposit.            

Roof Lodge Evolution 2 Awning / Blind 200 / 250 / 300cm The new Evolution awning is the perfect travel companion. The large, sturdy awning offers ideal sun and rain protection and helps to keep rising warmth in the evenings. The practical ground rail allows fitting to a number of common roof racks. The awnings are available in widths of 140, 200, 250 cm to fit e.g. a Land Rover Defender 110. The extended length of the awning is always 200 cm regardless of width. The awning is made of PU coated rip-stop Polycotton fabric (a mixture of 65% polyester and 35% cotton), which has excellent water and dirt repellent properties while also being very durable and shape-retaining. Lightweight aluminium telescopic poles help to tighten the awning and set the correct height. The poles can be extended up to 220 cm. The awning is supplied with 2 pegs, 2 cords, 2 L-shaped mounts, 4 8x20 mm steel screws, 2 8x20 mm bolts and a spanner. A pack sack is supplied, which remains on the vehicle together with the rolled up awning. This item is sent as bulk goods. The total delivery weight differs from the actual item weight. The actual weight is: awning 200 cm: 10 kgawning 250 cm: 10.6 kgawning 300 cm: 12 kg surface: 200 x 200/250 cm awning material: 280 g/sqm RipStop Polycotton (65% polyester and 35% cotton), PU coated; water and dirt repellent; resistant to wind noise because of heavy quality colour: stone greyPlease choose the desired width. You can also order an additional extension in the same width. The extension is made from the same high-quality material than the awning itself and gives ideal sun, side and wind protection. The extension is simply fitted to the existing weld track / c-profile of the awning. The extension is secured to the ground with supplied pegs and cords. Awning 200 cm with extension: 11.7 kgAwning 250 cm with extension: 12.4 kg Attention: The extension cannot be fitted at the same time as the ground tent for the awning as it uses the same weld track.

Mobile parking heater without battery and in aluminium box You can find information on hire equipment below. “It's a Thin Line Between Love and Hate” is the old song and this thin line between loving and hating the same thing is definitely the line on the thermometer in winter. If you freeze off the part of your body with an A, you're guaranteed not to enjoy even the fattest fish at the ice hole, the most magical aurora borealis or the greatest fun at the elephant meeting. That's why we have our solution for all outdoor activities in the cold seasons in the Alubox Pro: the AUTOTERM parking heater for on the go! With the exception of the battery, everything you, your family or your crew need for a warm and cozy outdoor feeling in your car, camper or roof tent is in the ultra-robust, waterproof 29L box. At its heart is the affordable and powerful AUTOTERM (Planar) 2D12 air heater, which can be powered from the vehicle battery via the cigarette lighter adapter. It is controlled via the PU5 control element. A 5.4 l fuel tank is already integrated in the box. This makes our mini heater ideal for on the road and mobile use on the vehicle or wherever a weatherproof cable connection to a car battery can be established. The warm air is transported into the room to be heated via a firmly screw-fastened, waterproof Flexi hose, which can be ordered separately in the desired length here in the store. ATTENTION: As a precaution, we would like to point out that operation in closed rooms is not permitted due to the risk of poisoning from exhaust fumes. Furthermore, for optimum heating performance, care should be taken to ensure that the air inlets for combustion and hot air are positioned so that they are protected from the weather. You can find the perfect storage bag for the Flexi hose here in the store.A larger standalone version of this parking heater with integrated battery is available here. You can also hire this parking heater from us.  Alu-Box Pro (29 liters) waterproof/dustproof according to IP54 standard AUTOTERM (Planar) 2D diesel / air heater ✔ Fuel tank (5.4 liters)✔ Hot air pipe connection, non-return valve, outlet and inlet feed-through✔ Including radio remote control✔ The openings for supply and exhaust air and for the power supply are splash-proof (can be closed with a screw cap or rubber plug)Dimensions of the aluminum box: WxHxD 390x340x290mmDimensions of the box with spigot: WxHxD 490x340x290Total weight: 11.2 kgTechnical data of the parking heater:- Fuel type: Diesel- Heating output: max. 1.8kW, min. 0.8kW- Volume of heated air: max. 75m³/h, min. 34m³/h- Fuel consumption during operation: max. 0.24l/h, min. 0.1 l/h- Power consumption during operation: max. 29W, min. 10W- Manual start/stop- Connection to a car battery or another external 12V battery PU-5 control element: - LED for ventilation display- LED for operating display- Temperature adjustable via rotary control The AUTOTERM Air 2D (Planar 2D) is equipped with an altitude kit! This means that the heater automatically reduces the injection volume according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content falls. The maximum heat output decreases in proportion to the amount of oxygen in the air. Roughly speaking, from 2000 meters upwards, the loss of output per 500m altitude is approx. 5%. Manufacturer tests up to 3440m were problem-free. No problems are to be expected up to 4000m. Up to 5000m the software calculates itself - but this could not yet be tested at real altitude. Please note: Most portable power stations or battery boxes (such as Goal Zero, Eco Flow, Bluetti etc.) are unfortunately not suitable for operating the mobile parking heaters.The heater requires up to 15A as starting current and when shutting down, but very few battery boxes can provide this..In general, however, direct connection to the battery terminals is the best solution   If you want to heat the interior of your vehicle, we offer an installation service for warm air ducting through a ventilation plate.   Please note the legal information on batteries HERE. For certain types of batteries, we are legally obliged to charge a deposit.        

Ready-to-go roof tent: Evolution 2 Basic incl. accessories You're woken up by the rays of the morning sun shining through the rain-proof roof-top window. You've slept well thanks to the comfortable mattress and the 3D mesh underneath. You're having a look around - there is plenty of space, no mosquitos or other insect that are flying around. You open the entrance and get your shoes out of the separate storage net to begin your descent.  That's your adventure. That's exactly where you want to be! For how long? That's up to you. Your vehicle gets you everywhere and the Nakatanenga Roof Lodge Evolution roof tent gives you all the freedom to stay or to travel onwards! Roof Lodge Evolution 140 Basic Features tent outer fabric: 320 g/sqm Polycotton, PU coated; the darker fabric allows for long sleep through the morning hours awning: 190T nylon fabric, nomad, PU coated; the relatively heavy weight minimizes fluttering noise 2 roof windows with rain and mosquito protection ground tent: - adjustable for tent mounting heights from about 170 cm to 210 cm- base area: 140 cm x 120 cm- floor pan PVC fabric- durable cover made of PVC fabric (similar to lorry canvas covers)- 4 side skirts; window and entrance with close-mesh fly sheeting- the lighter fabric allows outside light to enter the awning thermoplast honeycomb floor; made in Germany once-piece matress (60mm thickness); available in two degrees of hardness, manufacturer: Saar-Schaum, Germany separate 3D base mesh (10mm thickness) for relaxing sleep; the mat prevents condensation close mesh mosquito fly sheeting on all windows and entry  Additionally supplied with: aluminium ladder for a tent mounting height up to 2 metres, adjustable to vehicle height (optional extension available) hard-wearing protective cover made of PVC fabric (similar to lorry canvas covers) 2x LED interior light 2 Nakatanenga travel cushions 8 flexible steel poles fitting material and necessary toolsThe supplied fitting material allows fitting to standard roof bars with a width of up to 45mm. Should you plan to fit differently please contact us in advance - we can help you with alternative fitting scenarios. pre-drilled mounting rails, to be cut to length according to your requirements (instructions in the supplied fitting instructions) Size and Weight sleeping size: 140 cm x 240 cm ; height approx. 120 cm pack size: 147x124x40 cmThe height of the folded tent is about 45 cm, being the sum of the mounting rails, height of the folded tend and the height of the ladder that rests on top of the folded tent. The ladder can be detached from the tent (e.g. when overall height is important like on ferries, etc. weight of tent: 45 kg (incl. protective cover, ladder, mounting rails) can be fitted to vehicles (also passenger cars) with a mounting height up to 2.10 m Information on the subject of roof loads can be found in the manuel / data sheet tab. Further keywords for this item: roof lodge, roof loge rooflodge, roof tent, roof-lodge, roof-tent We will be happy to advise you: ☎ +49 9181 466 644

Telescopic ladder for ROOFLODGE EVOLUTION roof tent - spare part, up to 2.15 m long Product information Ladder can be used as a spare part for our ROOFLODGE EVOLUTION folding tents. Rung width: 30 cmLadder dimensions: retracted 1.2 m / extended 2.15 m Here you will find a matching ladder extension - for up to a further 45 cm.Please note that for older Roof Lodge Evolution folding tent models, the ladder bracket must be remounted on the base plate of the roof tent.

Nakatanenga Bear Pillow Travel pillow and cuddly bear in one!The Nakatanenga Bear Pillow! Fluffy soft and bearish good! Pillow with microbead filling, incl. nylon storage bag with drawstring.2in1 - pillow with filling, winter/summer side, certified according to Oeko-Tex 100 standard.Turning the fur around turns the cuddly bear into the cushion and the cushion into the bear again. On the outside, Nabaki's plush fur is fluffy and soft, and on the inside there is a double-sided cushion with a winter and a summer side, both certified according to Oeko-Tex 100. The filling consists of microbeads for restful sleep. And for Nabaki's dust-free winter or summer sleep in the wardrobe, we also supply a storage bag with cord.Nabaki is the bear among travel pillows - day and night!Colour: brownMaterial: Plush cover: 100% polyesterSmooth side: 87% Polyester / 13% SpandexFilling: 100% polystyrene