Complete suspension TREKFINDER for LAND ROVER Defender 110 with TREKFINDER Raid +20/0 millimeter

Take a Deep Breath – with the Raised Air Intake for Your Land Rover Defender! Your Defender is built for adventure. But what if those adventures take you through deep water crossings or extremely dusty tracks? This is precisely where our raised air intake, also known as a snorkel, comes into play and becomes an indispensable companion for your Land Rover Defender 90, 110, or 130. Imagine crossing a river. With a standard air intake, you risk water getting into the engine – an expensive problem you can avoid. Our raised air intake relocates the intake point to roof height. The result: a significantly reduced risk of engine damage from water. But that's not all! The snorkel also shows its strengths in dry, dusty regions. The air at roof height is cleaner and contains fewer dust particles than near the ground. This means your air filter gets dirty slower, needs to be cleaned or replaced less often, and your engine can breathe more freely. This snorkel, made of robust black plastic, even comes with an integrated cyclone filter that pre-separates coarse particles, further increasing efficiency. Installation is on the right side of the vehicle, and thanks to the EU-wide valid TÜV parts certificate, registration is no problem either. So, you're not only safer but also legally on the road. Your advantages at a glance: Optimal Engine Protection: Significantly reduces the risk of water damage during river crossings. Cleaner Intake Air: Less dust and dirt enter the engine, which protects your air filter and extends its lifespan. Integrated Cyclone Filter: For even more effective pre-separation of dirt particles. Robust Design: Made from durable, black plastic. TÜV Parts Certificate: For hassle-free registration (valid EU-wide). Perfect Fit: Suitable for Land Rover Defender 90/110/130, models 300Tdi, Td5, Td4 2.4 & Td4 2.2 (Puma/TDCI). Easy Installation: On the right side of the vehicle. Equip your Defender for real challenges and ensure it always gets the best air to breathe. With this raised air intake, you're prepared for any terrain! With EU-wide valid TÜV parts certificate! Suitable for Land Rover Defender 90/110/130, 300Tdi, Td5, Td4 2.4 & Td4 2.2 (Puma/TDCI)

Nakatanenga CargoBear 2.0 – Lightweight Roof Rack for Land Rover Defender 90, 110 & 130 When it comes to sheer performance, our CargoBear has always been the Grizzly among roof racks. Strong, sturdy and extremely versatile, it was already well ahead of its time when we introduced it in 2016. But the world keeps turning, evolution never stands still – and anything that wants to survive in nature has to keep evolving. Leaner and meaner, as boxers say, the new bear – the CargoBear 2.0 – emerges from its den in Berg. Same load capacity, same strength, same rigidity, but with a significantly reduced fighting weight. Around 30 % less weight on the scales also means around 30 % less weight on the vehicle roof. And on top of that, the new CargoBear is considerably less expensive! How did we do it? The crucial difference lies in the new construction. Instead of the heavy longitudinal beams, newly developed perforated HIGRIP plate modules and edge plates now provide the longitudinal bracing, achieving the same structural values with a considerable reduction in weight. One point is especially important to us: the CargoBear 2.0 is manufactured entirely by Nakatanenga in Germany. All production and finishing steps take place either in-house or with specialised companies from our region. It is elaborate and certainly not the cheapest way to build a roof rack – but for us it is the right one: short distances, direct communication and the highest standards for materials, workmanship and quality. Made in Germany – not just as a sticker, but from the first component to the finished roof rack. The CargoBear 2.0 has been designed for a load capacity of 300 kg off-road (with an evenly distributed load). On the road, this value could theoretically be doubled. However, two points that apply to roof racks in general must always be kept in mind: First, a loaded roof rack can significantly raise the vehicle’s centre of gravity, which is especially important off-road. Second, the decisive limit when loading the roof rack is the vehicle manufacturer’s permitted roof load, which in most cases is significantly lower than the load capacity of the rack itself. Some things remain unchanged on the new bear: the jet-black, super-flat look, the high-performance material and the modular versatility. All accessories, add-on components, roof tents etc. are fully compatible with the first generation. And last but not least, the previous, heavier CargoBear with longitudinal beams and chequer plate continues to be available exclusively for classic Defenders requiring specific heavy-duty applications. Matching accessories are available in our shop, including the end crossbar, the wind deflector and the angled wind deflector – perfectly matched for even greater functionality and comfort. PLEASE NOTE: When using a snorkel, the wind deflector may need to be adjusted. On Defenders with a pop-up / lifting roof, the original vehicle roof is often shortened. In this case, the roof rack may not fit. Please measure beforehand or contact us in advance if there are any questions. The CargoBear can be used on an Alu-Cab pop-up roof.  OVERVIEW OF ALL CARGOBEAR CONFIGURATIONS FOR THE LAND ROVER DEFENDER Defender 90 1,890 mm - 2 Modules optional: end beam, wind deflector Defender 90 2,075 mm - 3 Modules optional: end beam, wind deflector Defender 90 2,075 mm - 3 Modules incl. inclined extension (front module) optional: end beam, wind deflector Defender 90 1,005 mm - 1 Module optional: end beam, wind deflector   Defender 110 SW/HT 2,775 mm - 3 Modules optional: end beam, wind deflector Defender 110 SW/HT 2,765 mm - 3 Modules incl. inclined extension (front module) optional: end beam, wind deflector Defender 110 SW/HT 1,890 mm - 2 Modules optional: end beam, wind deflector Defender 110 SW/HT 1,005 mm - 1 Module optional: end beam, wind deflector   Defender 110 DC 1,545 mm - 2 Modules optional: end beam, wind deflector Defender 110 DC 1,545 mm - 2 Modules incl. inclined extension (front module) optional: end beam, wind deflector Defender 110 DC 1,005 mm - 1 Module optional: end beam, wind deflector   Defender 130 1,545 mm - 2 Modules optional: end beam, wind deflector Defender 130 1,545 mm - 2 Modules incl. inclined extension (front module) optional: end beam, wind deflector Defender 130 1,005 mm - 1 Module optional: end beam, wind deflector   Available lengths (dimensions and weights): Modules: Configuration: Length: Weight: 1 Module 1x L 1,005 mm 17.5 kg 2 Modules 1x L + 1x K 1,545 mm - suitable for 110 DC, 130 CC 26.5 kg 2 Modules 2x L 1,890 mm - suitable for 90 30 kg 3 Modules 3x L 2,775 mm - suitable for 110 SW/HT 42.5 kg 3 Modules with angled or straight extension 1x L + 2x K 2,075 mm - ideal for 90 35.5 kg 3 Modules with angled extension 3x L 2,765 mm - ideal for 110 43 kg Angled extension module   875 mm 13 kg Long extension module   885 mm 12.5 kg Short extension module   540 mm 9 kg   Installation note:M10 button-head screw: 20 Nm to 25 NmM6 button-head cylinder screw: 10 Nm to 12 Nm Measured from the gutter, the CargoBear is approx. 23 cm high. It adds approx. 5–6 cm above the roof itself – depending on the roof, its condition, model year etc. You can find ideal protection for the lashing rail profile on the CargoBear or for all other lashing rails here.  

Comfort spring set TREKFINDER for LAND ROVER Defender 110 with VA +20 / HA +0 millimetres the lifting is +20 millimetres at the front axle, +0 millimetres at the rear axle matched to the TREKFINDER® shock absorbers Raid ( article no. 90-5470 + 905471 ) SCOPE OF DELIVERY: 4 pieces TREKFINDER® coil springs progressive 1 piece TÜV® parts certificate Suitable for Land Rover Defender 110 until BJ 2016  

Lifting suspension TREKFINDER for Land Rover Defender 110 - with TREKFINDER shock absorber KONI Heavy Track RAID - with approx. +40 millimetre lift To optimise the Land Rover Defender 110, the renowned shock absorber manufacturer KONI and the spring manufacturer H&R and STOCK & STEIN have joined forces to offer the best possible solution for suspension optimisation. The suspension has been designed for vehicles with an additional weight of up to approx. 80 kg on the front axle and approx. 250 kg on the rear axle. This means that regardless of whether your Defender is equipped without a payload and additional attachments, or whether, for example, a cable winch has been installed at the front, a roof rack in the middle and camping equipment at the rear - the suspension masters all driving situations! Scope of delivery:* 4 TREKFINDER coil springs * 4 TREKFINDER shock absorbers * 1 TREKFINDER sticker * 1 parts certificate Due to the increased articulation angle of the front cardan shaft caused by the lift, we recommend the installation of a cardan shaft with double joint.  Cardan shaft for Defender Td4 from MY07 can be found here. Cardan shaft for Defender Tdi/Td5 up to MY07 can be found here.   

HD suspension for Land Rover Defender 110 (for heavily loaded rear axles) Set consists of:  1x TREKFINDER coil springs  2x front axle shock absorbers 2x holder for additional spring, rear, bottom 2x bracket for additional spring, rear, top 1x lift spring set for Land Rover Defender 110 2x shock absorber Koni HeavyTrack RAID Defender  Due to the increased articulation angle of the front cardan shaft caused by the lift, we recommend the installation of a cardan shaft with double joint.  Cardan shaft for Defender Td4 from MY07 can be found here.  Cardan shaft for Defender Tdi/Td5 up to MY07 can be found here.