Steering damper reinforced TREKFINDER for SUZUKI Jimny II from 2018 type GJ & HJ reliably reduces, prevents and eliminates steering wheel vibrations in/on your Jimny if all attempts and efforts such as balancing the wheels, adjusting the toe, correcting the caster, replacing the wheel and steering knuckle bearings, etc. have not been successful........this steering damper will certainly help you :) the installation of the steering damper is very easy and plug and play, the standard damper is simply replaced, the new steering damper fits to the standard mounting points. drilling, welding, deburring, painting etc. is NOT necessary for the installation of our steering damper very suitable for Jimny's WITH and WITHOUT lowering or raising the vehicle the Foam Cell technology in the twin-tube damper with 35 mm piston rod and maximum volume prevents the mixing of gas molecules in the oil, guarantees a long service life and perfect performance in ON- and OFFROAD OPERATION track adjustment is NOT necessary after assembly SCOPE OF DELIVERY: 1 piece TREKFINDER steering damper/Foam Cell Technology

Spring Spacer Ring/ Trim Packer/ Lifting Ring TREKFINDER for SUZUKI Jimny I & II + 10 Millimeter in colour red - for levelling at the front or/and rear axle. Suitable for all Jimny models at the front and rear axle: Jimny II type GJ & HJ as of MY 2018 Jimny I type FJ until MY 2018 for the front axle spring for the rear axle spring 10 millimetre height adjustment SCOPE OF DELIVERY: 1 piece TREKFINDER polyurethane spring distance ring with marking TREKFINDER logo + FDR10 in colour red. NOTE: The spacer rings are listed in the TÜV® parts certificate for our TREKFINDER Jimny II complete suspension 40 mm and Jimny I suspension 55 mm and can therefore be optionally installed 1x per spring.A general TÜV® parts certificate is not available or is NOT included in the scope of delivery. MOUNTING INSTRUCTIONS: The installation is carried out between the upper end of the spring and the spring plate. Make sure that the brake line is long enough Make sure that the shock absorber is long enough. Check the headlight setting. The permissible height of the coupling ball must be observed. If there is a load-dependent headlight adjustment, e.g. for LED lights, this must be checked and, if necessary, adjusted or changed/extended. If a new measurement or calibration of the sensors of the driver assistance system is necessary due to the changed vehicle geometry of the vehicle, this must be carried out according to the specifications of the vehicle manufacturer. For vehicles with load-dependent brake pressure regulator, this must be readjusted to the empty level (according to the vehicle manufacturer's specifications). After retrofitting, the axle geometry of the vehicle must be measured and, if necessary, corrected according to the vehicle manufacturer's specifications.

Parts certificate TREKINDER for tyre conversion SUZUKI Jimmy II type GJ/HJ with aluminium rim/steel wheel 15 x 5.5 to tyre size 215/75R15 or 205/75R15 or 215/70R15   With this TÜV® parts certificate, you can easily fit the tyre sizes mentioned and have them registered by a test centre for Jimny II models type HJ with ABE-EG number: e6*2007/46*0515*. a speedometer check or new setting is required (on our Jimny the speedometer fitted with Goodrich AT) 1 TÜV® parts certificate is delivered as a document with the parcel service ( insured shipping ) only 1 part certificate will be delivered, NO tyres, NO rims etc. ! the illustrations/photos in the webshop serve exclusively as a visual aid for a 215/75R15 tyre on the original Jimny aluminium or steel rim, no tyres are included in the scope of delivery. the use of snow chains is not permitted ! there is NO brand binding for the tyres ! NO additional mudguard extensions are required ! it is NOT possible to send the certificate by e-mail or fax !    

Installation kit Suzuki Jimny GJ / HJ with Nolden 90 mm combination fog lights/daytime running lights Especially with hard-working off-road vehicles such as the Suzuki Jimny GJ, it is worthwhile converting completely or partially to LED headlights and lamps: they generally provide better light output, are less susceptible to damage and have a longer service life. With our complete installation kit consisting of Nolden 90 mm LED combination lights for daytime running lights and fog lights and the matching adapter cable, burnt-out, corroded or broken bulbs are a thing of the past. The Nolden combination lights combine both a daytime running light ring with fibre optic technology and an LED fog light in a high-quality chrome housing. Nolden uses high-quality LEDs from Osram, which are also extremely economical at 8.1 W for the daytime running light and 8.8 W for the fog light. Installation of the LEDs is extremely simple, with the appropriate adapter cables from PS13W socket to AMP Superseal plug for the daytime running lights included. The fog lights are plug & play. If you only need the adapter cables, you can find them here. The complete installation kit consists of two adapter cables and a set of Nolden 90 mm LED combination lights daytime running lights/fog lights. Scope of delivery: 1 x pair of Nolden 90 mm LED daytime running/fog lights chrome Adapter: 2 pieces PS13W socket 2-pin to AMP Superseal plug 3-pin.   Note:  The headlights also fit various Subaru models (including the Subaru Levorg), which are equipped with 90 mm combination headlights (fog and daytime running lights) as standard. Depending on the vehicle, it may be necessary to repin the plus and minus wires on the wiring harness for the daytime running lights (the easiest way to do this is at the Superseal connector).    

Underride protection TREKFINDER for SUZUKI Jimny II type GJ / HJ EXHAUST GAS CONTROL SYSTEM suitable for all Jimny models of the type GJ built from the end of  2018 and Type HJ suitable for all engine and transmission types from 3 millimeters of steel yellow galvanized including all mounting parts attachment to original points of the vehicle