LED signal lamps for Land Rover Defender, smoke grey The advantages of LEDs are well known: low power consumption, strong light output, vibration resistance and a long lifetime. In this smoke grey signal lamp set for the Land Rover Defender (Series III, Defender 90, Defender 110, Defender 130) the following LEDs are included: The standard-set with 8 bulbs contains: 2x front indicatior ligths 2x front position lights, either with or without day-driving light 2x rear indicators 2x brake/rear lights adjustable indicator relay The set with 9 bulbs additionally (aditionally to the standard-set) contains:  1x tailgate break light The set with 10 bulbs additionally (aditionally to the standard-set) contain:  → 1x fog light and 1x reverse light→ OR 2x wing side indicators The set with 11 bulbs additionally (aditionally to the standard-set) contain:  → 1x fog light, 1x reverse light and 1x tailgate break light→ OR 2x wing side indicators The set with 12 bulbs additionally (aditionally to the standard-set) contains:→ 1x fog light and 1x reverse light and 2x wing side indicators The set with 13 bulbs additionally (aditionally to the standard-set) contains:→ 1x fog light and 1x reverse light, 2x wing side indicators and 1x tailgate break light Note that indicators must be orange by law. All bulbs come with E-approval so that they can be fitted without further TUV recording. All bulbs come with correct plugs for simple replacement for vehicles from MY 1998 (TD5 und TD4). Fittings are supplied and also an adjustable indicator relay that even allows to adjust indicator speed. Older vehicles can be retrofitted after removing the plug. This requires soldering. If the lamps on the existing vehicle are square at the rear, you need 1x AMR3850 mounting base per lamp to mount the new round reversing lights. As a rule, the original drill holes can be used. This signal lights kit is the ideal addition to our 7" Bi-LED main headlights, the LED license plate light and any additional LED spotlights - this brings the Land Rover Defender into the 21st century light-wise! Please note: The screws must not be over tightened (only hand-tight!), Otherwise the plastic housing may crack. These cracks could allow water to penetrate into the generally watertight luminaires. Use only a screwdriver and NO cordless screwdriver!

LED turn signal rear for Land Rover Defender in white, single With E-mark and a diameter of 75 mm. Suitable for Land Rover Defender until MY2016Please also note our bundles with all signal lights and price advantage: LED signal lights for Land Rover Defender. For these indicators you need our four-pole indicator relay, which also offers the feature of being able to set the indicator speed yourself. Please note: The screws must not be tightened too much (only hand-tight!), otherwise the plastic housing can get cracks. Through these cracks, water could penetrate into the generally waterproof luminaires.Only use a screwdriver and NOT a cordless screwdriver!  

LED rear indicators for Land Rover Defender, orange, E-marked Suitable for Land Rover Defender until MY2016Please see our bundles with all signal lights at a saving: LED signal lights for Land Rover Defender For these indicators you need our four-pole indicator relay, which also offers the feature of being able to set the indicator speed yourself. Please note: The screws must not be over tightened (only hand-tight!), Otherwise the plastic housing may crack. These cracks could allow water to penetrate into the generally watertight luminaires. Use only a screwdriver and NO cordless screwdriver!

LED signal lights Land Rover Defender up to MY2016: Indicators, front, amber Front LED indicators for Land Rover Defender in yellow, single. With E-mark.  Suitable for Land Rover Defender up to MY2016. If the lamps on the existing vehicle are square at the rear, you need 1x AMR3850 mounting base per lamp to fit the new round indicator lights. As a rule, the original drill holes can then be used. Please also note our bundles with all signal lights and price advantage: LED signal lights for Land Rover Defender. For these indicators you need our four-pole indicator relay, which also offers the feature of being able to set the indicator speed yourself.  Please note:  The screws must not be overtightened (only hand-tight!), otherwise the plastic housing may crack. These cracks could allow water to penetrate the generally waterproof lights. Only use a screwdriver and NOT a cordless screwdriver!    

LED signal lights Land Rover Defender until MY2016: turn signal, front, white LED turn signal front for Land Rover Defender in white, single.With E-mark. Suitable for Land Rover Defender until MY2016 If the lamps on the existing vehicle are square at the rear, you need 1x AMR3850 mounting base per lamp to mount the new round signal lamps. As a rule, the original drill holes can be used. Please note: The screws must not be tightened too much (only hand-tight!), otherwise the plastic housing can get cracks. Water could penetrate the generally waterproof lights through these cracks.Only use a screwdriver and NOT a cordless screwdriver!