AUTOTERM air 4D (Planar 44D) diesel / air parking heater with additional tank.As a low-priced and powerful alternative to our complete Webasto parking heater kits, we offer the AUTOTERM 4D (formerly Planar 44D) parking heater. The particularly compact dimensions and its heating power of 4 kW allow installation even in small cars, vans off-roaders motor homes, construction machines, boats or under difficult installation situations. The extensive range of accessories supplied simplifies installation. The parking heater has an approval for the European market (ECE mark) and can therefore be installed without registration. The hole pattern here corresponds to the familiar heaters of Eberspächer Airtronic and Webasto AirTop 2000, so that here can be easily replaced without having to drill new holes in the body.All AUTOTERM parking heaters are characterized above all by their durability and reliability with economical consumption. In addition, the heater also has a switchable ventilation function.The parking heater can also be operated while driving. Extensive accessories are available here in our store. The AUTOTERM 4D (prev. 44D) parking heater needs warm air pipes and outlets with 75 mm diameter.Running time: The AUTOTERM parking heater switches off automatically after 2 hours of operation. However, once you press a button during operation, the parking heater will continue to run indefinitely until it is manually turned off.Scope of delivery:- Control element (either simple control PU-5 or Comfort Control depending on your selection.- metering pump- Rubber holder metering pump- Wiring harness metering pump- Wiring harness heater- Intake air hose with integrated silencer- Heat protection hose- End piece exhaust pipe incl. clamp- Tank intake pipe- 5.5 m fuel line- 7 l fuel tank plastic (width: 33 cm + 3 cm intake manifold; height: 26.5 cm + 3 cm bracket + 4.5 cm screw cap, depth: 10 cm)- 300 mm fuel line connector- 1 m corrugated metal exhaust pipe- exhaust silencer- screws, nuts, clamps, heat shrink tubing, cable ties- Instruction manualTechnical data:- Fuel type: diesel- Heating power: max. 4 kw, min. 1 kw- Volume of heated air: max. 120 m³/h, min. 70 m³/h- Fuel consumption in operation: max. 0,514 l/h, min. 0,12 l/h- Power consumption in operation: max. 62 W at 12 V operating voltage, max. 58 W at 24 V operating voltage, min. 10 W- Manual start/stop → On the Autoterm.cz site you can find a calculator for correct air heater sizing,You can choose between two control elements:- PU-5 control element with rotary control: the old PU-10 control element had a relatively inaccessible control surface. Therefore, the reliable control element with rotary control is now the new improved standard of Planar parking heaters! With the rotary control you can adjust the heating power of the parking heater and regulate the power of the ventilation in the ventilation mode! The PU-5 control element with rotary control can also be purchased separately here.- The digital control element Comfort Control with timer has an OLED display and an understandable and clear interface.  Temperature, ventilation and power can be configured via the display and the various buttons. With the new timer, you simply set the start of the parking heater to a specific time. The organic light-emitting diodes of the display ensure a particularly high contrast and low power consumption. The digital control element with timer can also be purchased separately here.Setting options (Comfort Control): Temperature and power (adjustable for the parking heater, the control panel and for an external heater) Time and date Operating language (English or Russian) Functions of the timer (Comfort Control): Memory function: save time so that the parking heater starts at this time every day Configurable memory locations: Up to 3 different days of the week with different times can be set and stored. The AUTOTERM Luft 2D (Planar 2D) is equipped with a height kit!This means that the heater independently reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heating power decreases proportionally to the amount of oxygen in the air. Roughly one can say: From 2,000 meters the loss of power per 500m altitude is about 5%. Manufacturer tests up to 3.440 m were without problems. Up to 4,000 m, no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not be tested in real altitude yet. Please note: Use this 4 kW heater only if this size is really erforgerlich! It is expressly not recommended to permanently turn down the heating. In case of less demand the AUTOTERM Luft 2D (former Planar 2D parking heater) is recommended. If the larger heater is used on a long-term basis on a lower load, the combustion chambers will quickly become sooty - which will cause the heater to fail. https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Planar 2D Auxiliary Vehicle Heater We offer the Planar 2D auxiliary vehicle heater as a well-priced, powerful alternative to our Webasto auxiliary vehicle heater kits. With their compact size and a heater output of 1.8 kW, the Planar 2D is well-suited for fitting to smaller vehicles, vans, off-roaders, camper vans, boats or in confined spaces. It is ideal for 'typical' off-road vehicles like the Land Rover Defender, Mercedes G oder Jeep Wrangler JK. The extensive fitting kit that is supplied with each heater make fitting easy. The Planar 2D can be easily controlled via its analogous control unit, with 8 settings available from 0,8 - 1,8 kW heat output. Available as both, 12 volts or 24 volts, this heater is European market approved (ECE label) and can thus be fitted independet of TUV approval. The parking heater has approval for the European market (ECE test mark) and can therefore be installed without registration. The hole pattern is the same as that of Eberspächer Airtronic and Webasto AirTop 2000 heaters, so that an old unit could easily be replaced without drilling additional holes.A space-saving version with a 90° angle can be found here.  All Planar auxiliary vehicle heaters are extremely long-lasting and durable, as well as very frugal. The heater can also be used while driving. And extensive range of additional equipment is available in our online shop. Attention Defender drivers: Our extensive Planar full-set for Land Rover Defender not only includes everything needed to perfectly fit the heater to your Tdi, Td5 or Td4 Defender, but also offers considerable savings over the individual purchase of all included items. Comes with: - 12 V or 24 V heater- Optionally analogue PU-5 control panel with rotary control or digital Comfort Control control panel with timer- Thomas Magnet P327" dosing pump- Exhaust silencer- Dosing pump rubber holder- Dosing pump wiring harness- Heater wiring harness- Intake air hose with integrated silencer- Heat protection hose- Exhaust pipe end piece + clamp- Tank intake pipe- 5.5 m fuel line- 300 mm fuel line connector- 1 m corrugated metal exhaust pipe- Fastening material (screws, nuts, clamps, heat-shrink tubing, cable ties)- Operating instructions Technical details: ·         fuel: diesel·         heat output: max. 1.8 kw, min. 0.8 kw·         air volume: max. 75 m³/h, min. 34 m³/h·         fuel consumption: max. 0.24 l/h, min. 0.1 l/h·         power drain: max. 29 W, min. 10 W·         manual start/stop→ On the Autoterm.cz website you will find a calculator for the correct dimensioning of the air heater The AUTOTERM Luft 2D (Planar 2D) is equipped with a height kit!This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents shooting of the combustion chamber when the atmospheric oxygen content drops. The max. Heating power drops in proportion to the amount of oxygen in the air. Roughly one can say: From 2.000 meters the loss of power per 500 m height is approx. 5%. Manufacturer tests up to 3.440 m were no problem. No difficulties are to be expected up to 4.000 m. The software itself calculates up to 5.000 m - however, this has not yet been tested in real height. The separately available control unit with timer (optional extra) features a larger OLED display and more intuitive operation. Temperature, ventilation and output can be configured via a display and various switches. An added timer clock allows you to set the heater to a specific time. OLED display provides maximum visibility with minimum power drain.  Possible settings:- temperature and output- time and date- language (English or Russian) Features of the new timer clock:- daily: one fixed time at which the heater starts each day- individual: up to thee different settings with different days and times. The improved new control unit is also available separately.  https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Parking heater set for the VW T5 consists of all important components required for the installation of a parking heater. First and foremost, the set contains the AUTOTERM (=Planar) 2D12 parking heater, which is celebrated as an affordable and powerful alternative to Webasto and Eberspächer parking heaters. In addition to the heater holder with installation box, which can already be ordered individually and which was specially designed for the installation of the Planar parking heater in the VW T5, with this set we put together a comprehensive package for you with a matching hose clamp, fuel line, air duct, a warm air outlet and much more. As some components for the B-pillar vary depending on the vehicle model, please select the matching set for your VW T5 estate / panel van OR Multivan / Shuttle / California. Please note: This set is not suitable for vehicles with a partition wall! Scope of delivery: AUTOTERM 2D parking heater 12 volt incl. silencer, intake air hose, heat protection hose, tank intake pipe and exhaust corrugated pipeOptionally analogue control unit simple control (PU-5) with rotary control or digital control unit Comfort Control with timer switch5 metre connection cable for control panelSpecial heater bracket for VW T5, optionally with additional installation boxAir outlet for heating air 60 mm1 metre warm air pipe (diameter: 60 mm)60 mm to 90 mm adapterWarm air outlet for rear B-pillarAir duct for B-pillar incl. frameWarm air outlet for B-pillar frontAir ductFixing material (screws, nuts, hose clamp, cable ties)Technical data of the parking heater: Fuel type: dieselHeating capacity: max. 1.8 kW, min. 0.8 kWVolume of heated air: max. 75 m³/h, min. 34 m³/hFuel consumption in operation: max. 0.24 l/h, min. 0.1 l/hPower consumption in operation: max. 29 W, min. 10 WWeight: 3 kg (independent heater)Manual start/stop The AUTOTERM (=Planar) 2D12 is equipped with a height kit. This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heat output decreases proportionally to the amount of oxygen in the air. Roughly speaking, from 2,000 metres the loss of output per 500 m altitude is approx. 5%. Manufacturer tests up to 3,440 m were trouble-free. Up to 4,000 m no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not yet be tested at real altitude. Important:Especially when used at high altitude, the free travel of the fan is extremely important!Route the combustion air intake and exhaust extremely short and with low resistance - i.e. no kinks, no blockage or reduction. It should also be noted that operation beyond 3,000 m is still a technical compromise. Again, care should be taken to ensure that the combustion chamber is properly heated on a regular basis. The chamber must be burnt free of soot deposits. Soot deposits can also form on heaters that are permanently run at the lowest setting. Therefore, the following still applies: No guarantee for sooty combustion chambers! In order to ensure the longevity of the heater, you should also free-burn it occasionally at low levels. The combustion chamber reaches full temperature after running at full load for about half an hour. Normally, no further maintenance is required. In case of extreme loads, e.g. during longer overnight stays at more than 4,000 m, the combustion chamber including the seal set should be cleaned if necessary. We will be happy to advise you: 09181 / 466 644 ☎ https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Parking Heater AUTOTERM (Planar) 2D 12 Volt Complete Set for Land Rover Defender The parking heater set AUTOTERM (Planar) 2D12 for the Land Rover Defender consists of all important components needed for the installation of a parking heater. Included in the delivery are the AUTOTERM 2D 12 Volt parking heater, our Nakatanenga parking heater console, the Nakatanenga mounting plate, a fuel tank extraction, a Webasto air outlet with 60 mm connection, 30 cm warm air pipe and a vibration damper.As a low-priced and powerful alternative to our Webasto parking heater kits, the AUTOTERM (=Planar) 2D parking heater is proving to be a real sales hit. This is partly due to the particularly compact dimensions, which allow installation even in small cars, vans, off-roader motorhomes, construction machinery, boats or in difficult installation situations. In the off-road / 4x4 sector, it is ideally suited for the "typical" off-road vehicles such as Land Rover Defender, Mercedes G or Jeep Wrangler JK.These are only a few of many reasons why we now offer the AUTOTERM (Planar) 2D 12 V parking heater in a clear and comprehensive complete set for the Land Rover Defender at an economical price. For both the Tdi/ Td5 and the Td4, we offer one set each with a perfectly matching accessory kit.You can select different front panel cut-outs for the parking heater console included in the scope of delivery. The associated connections are available in the classic cigarette lighter format (12 V) or as 5 V USB charging sockets for Apple iPhones, navigation devices, iPads and smartphones and are included in the scope of delivery.The parking heater can also be operated while driving.Running time: The AUTOTERM parking heater switches off automatically after 2 hours of operation. However, as soon as you press a button during operation, the parking heater continues to run indefinitely until it is switched off manually.Scope of delivery:- AUTOTERM 2D parking heater 12 volt incl. silencer, intake air hose, heat protection hose, tank intake pipe and corrugated exhaust pipe.- Optionally analogue control unit simple control (PU-5) with rotary control or digital control unit comfort control (PU-29) with time switch- Nakatanenga parking heater console incl. the selected connections- Nakatanenga mounting plate- Fuel filler cap- Webasto air outlet with 60 mm connection, rotatable- 30 cm warm air pipe (diameter: 60 mm)- Vibration damper- Fixing material (screws, nuts, clamps, shrink hose, cable ties)Technical data:- Fuel type: diesel- Heating capacity: max. 1.8 kW, min. 0.8 kW- Volume of heated air: max. 75 m³/h, min. 34 m³/h- Fuel consumption in operation: max. 0.24 l/h, min. 0.1 l/h- Power consumption in operation: max. 29 W, min. 10 W- Weight: 3 kg (independent heater)- Manual start/stop → On the Autoterm.cz site you will find a calculator for the correct dimensioning of the air heater,You can choose between two control elements:- Simple Control (PU-5) element with rotary control: The old PU-10 control element had a relatively inaccessible control surface. Therefore, the reliable control element with rotary control is now the new improved standard of the Planar parking heaters! With the rotary control, you can adjust the heating power of the parking heater and regulate the power of the ventilation in ventilation mode! The PU-5 control element with rotary control can also be purchased separately here.- The digital control element comfort control (PU-29) with timer has an OLED display and an understandable and clear interface.  Temperature, ventilation and power can be configured via the display and the various buttons. With the timer, you can easily set the start of the parking heater to a specific time. The digital control element with timer can also be purchased separately here.Setting options comfort control (PU-29):- Temperature and power (adjustable for the parking heater, the control panel and for an external heater).- Time and date - Operating language (English or Russian)Functions of the timer comfort control (PU-29):- Memory function: save the time so that the parking heater starts at this time every day - Configurable memory locations: Up to 3 different weekdays with different times can be set and saved. The AUTOTERM (=Planar) 2D12 is equipped with an altitude kit.This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heat output decreases proportionally to the amount of oxygen in the air. Roughly speaking, from 2,000 metres the loss of output per 500 m altitude is approx. 5%. Manufacturer tests up to 3,440 m were trouble-free. Up to 4,000 m no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not yet be tested at real altitude. Important:Especially when used at high altitude, the free travel of the fan is extremely important!Route the combustion air intake and exhaust extremely short and with low resistance - i.e. no kinks, no blockage or reduction. It should also be noted that operation beyond 3,000 m is still a technical compromise. Again, care should be taken to ensure that the combustion chamber is properly heated on a regular basis. The chamber must be burnt free of soot deposits. Soot deposits can also form on heaters that are permanently operated at the lowest setting. Therefore, the following still applies: No guarantee for sooty combustion chambers!In order to ensure the longevity of the heater, you should also free-burn it occasionally at low levels. The combustion chamber reaches full temperature after running at full load for about half an hour. Normally, no further maintenance is required. In case of extreme loads, e.g. during longer overnight stays at more than 4,000 m, the combustion chamber including the seal set should be cleaned if necessary.https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

AUTOTERM air 4D (Planar 44D) diesel / air parking heater with additional tank.As a low-priced and powerful alternative to our complete Webasto parking heater kits, we offer the AUTOTERM 4D (formerly Planar 44D) parking heater. The particularly compact dimensions and its heating power of 4 kW allow installation even in small cars, vans off-roaders motor homes, construction machines, boats or under difficult installation situations. The extensive range of accessories supplied simplifies installation. The parking heater has an approval for the European market (ECE mark) and can therefore be installed without registration. The hole pattern here corresponds to the familiar heaters of Eberspächer Airtronic and Webasto AirTop 2000, so that here can be easily replaced without having to drill new holes in the body.All AUTOTERM parking heaters are characterized above all by their durability and reliability with economical consumption. In addition, the heater also has a switchable ventilation function.The parking heater can also be operated while driving. Extensive accessories are available here in our store. The AUTOTERM 4D (prev. 44D) parking heater needs warm air pipes and outlets with 75 mm diameter.Running time: The AUTOTERM parking heater switches off automatically after 2 hours of operation. However, once you press a button during operation, the parking heater will continue to run indefinitely until it is manually turned off.Scope of delivery:- Control element (either simple control PU-5 or Comfort Control depending on your selection.- metering pump- Rubber holder metering pump- Wiring harness metering pump- Wiring harness heater- Intake air hose with integrated silencer- Heat protection hose- End piece exhaust pipe incl. clamp- Tank intake pipe- 5.5 m fuel line- 7 l fuel tank plastic (width: 33 cm + 3 cm intake manifold; height: 26.5 cm + 3 cm bracket + 4.5 cm screw cap, depth: 10 cm)- 300 mm fuel line connector- 1 m corrugated metal exhaust pipe- exhaust silencer- screws, nuts, clamps, heat shrink tubing, cable ties- Instruction manualTechnical data:- Fuel type: diesel- Heating power: max. 4 kw, min. 1 kw- Volume of heated air: max. 120 m³/h, min. 70 m³/h- Fuel consumption in operation: max. 0,514 l/h, min. 0,12 l/h- Power consumption in operation: max. 62 W at 12 V operating voltage, max. 58 W at 24 V operating voltage, min. 10 W- Manual start/stop → On the Autoterm.cz site you can find a calculator for correct air heater sizing,You can choose between two control elements:- PU-5 control element with rotary control: the old PU-10 control element had a relatively inaccessible control surface. Therefore, the reliable control element with rotary control is now the new improved standard of Planar parking heaters! With the rotary control you can adjust the heating power of the parking heater and regulate the power of the ventilation in the ventilation mode! The PU-5 control element with rotary control can also be purchased separately here.- The digital control element Comfort Control with timer has an OLED display and an understandable and clear interface.  Temperature, ventilation and power can be configured via the display and the various buttons. With the new timer, you simply set the start of the parking heater to a specific time. The organic light-emitting diodes of the display ensure a particularly high contrast and low power consumption. The digital control element with timer can also be purchased separately here.Setting options (Comfort Control): Temperature and power (adjustable for the parking heater, the control panel and for an external heater) Time and date Operating language (English or Russian) Functions of the timer (Comfort Control): Memory function: save time so that the parking heater starts at this time every day Configurable memory locations: Up to 3 different days of the week with different times can be set and stored. The AUTOTERM Luft 2D (Planar 2D) is equipped with a height kit!This means that the heater independently reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heating power decreases proportionally to the amount of oxygen in the air. Roughly one can say: From 2,000 meters the loss of power per 500m altitude is about 5%. Manufacturer tests up to 3.440 m were without problems. Up to 4,000 m, no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not be tested in real altitude yet. Please note: Use this 4 kW heater only if this size is really erforgerlich! It is expressly not recommended to permanently turn down the heating. In case of less demand the AUTOTERM Luft 2D (former Planar 2D parking heater) is recommended. If the larger heater is used on a long-term basis on a lower load, the combustion chambers will quickly become sooty - which will cause the heater to fail. https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Planar 2D Auxiliary Vehicle Heater We offer the Planar 2D auxiliary vehicle heater as a well-priced, powerful alternative to our Webasto auxiliary vehicle heater kits. With their compact size and a heater output of 1.8 kW, the Planar 2D is well-suited for fitting to smaller vehicles, vans, off-roaders, camper vans, boats or in confined spaces. It is ideal for 'typical' off-road vehicles like the Land Rover Defender, Mercedes G oder Jeep Wrangler JK. The extensive fitting kit that is supplied with each heater make fitting easy. The Planar 2D can be easily controlled via its analogous control unit, with 8 settings available from 0,8 - 1,8 kW heat output. Available as both, 12 volts or 24 volts, this heater is European market approved (ECE label) and can thus be fitted independet of TUV approval. The parking heater has approval for the European market (ECE test mark) and can therefore be installed without registration. The hole pattern is the same as that of Eberspächer Airtronic and Webasto AirTop 2000 heaters, so that an old unit could easily be replaced without drilling additional holes.A space-saving version with a 90° angle can be found here.  All Planar auxiliary vehicle heaters are extremely long-lasting and durable, as well as very frugal. The heater can also be used while driving. And extensive range of additional equipment is available in our online shop. Attention Defender drivers: Our extensive Planar full-set for Land Rover Defender not only includes everything needed to perfectly fit the heater to your Tdi, Td5 or Td4 Defender, but also offers considerable savings over the individual purchase of all included items. Comes with: - 12 V or 24 V heater- Optionally analogue PU-5 control panel with rotary control or digital Comfort Control control panel with timer- Thomas Magnet P327" dosing pump- Exhaust silencer- Dosing pump rubber holder- Dosing pump wiring harness- Heater wiring harness- Intake air hose with integrated silencer- Heat protection hose- Exhaust pipe end piece + clamp- Tank intake pipe- 5.5 m fuel line- 300 mm fuel line connector- 1 m corrugated metal exhaust pipe- Fastening material (screws, nuts, clamps, heat-shrink tubing, cable ties)- Operating instructions Technical details: ·         fuel: diesel·         heat output: max. 1.8 kw, min. 0.8 kw·         air volume: max. 75 m³/h, min. 34 m³/h·         fuel consumption: max. 0.24 l/h, min. 0.1 l/h·         power drain: max. 29 W, min. 10 W·         manual start/stop→ On the Autoterm.cz website you will find a calculator for the correct dimensioning of the air heater The AUTOTERM Luft 2D (Planar 2D) is equipped with a height kit!This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents shooting of the combustion chamber when the atmospheric oxygen content drops. The max. Heating power drops in proportion to the amount of oxygen in the air. Roughly one can say: From 2.000 meters the loss of power per 500 m height is approx. 5%. Manufacturer tests up to 3.440 m were no problem. No difficulties are to be expected up to 4.000 m. The software itself calculates up to 5.000 m - however, this has not yet been tested in real height. The separately available control unit with timer (optional extra) features a larger OLED display and more intuitive operation. Temperature, ventilation and output can be configured via a display and various switches. An added timer clock allows you to set the heater to a specific time. OLED display provides maximum visibility with minimum power drain.  Possible settings:- temperature and output- time and date- language (English or Russian) Features of the new timer clock:- daily: one fixed time at which the heater starts each day- individual: up to thee different settings with different days and times. The improved new control unit is also available separately.  https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Parking heater set for the VW T5 consists of all important components required for the installation of a parking heater. First and foremost, the set contains the AUTOTERM (=Planar) 2D12 parking heater, which is celebrated as an affordable and powerful alternative to Webasto and Eberspächer parking heaters. In addition to the heater holder with installation box, which can already be ordered individually and which was specially designed for the installation of the Planar parking heater in the VW T5, with this set we put together a comprehensive package for you with a matching hose clamp, fuel line, air duct, a warm air outlet and much more. As some components for the B-pillar vary depending on the vehicle model, please select the matching set for your VW T5 estate / panel van OR Multivan / Shuttle / California. Please note: This set is not suitable for vehicles with a partition wall! Scope of delivery: AUTOTERM 2D parking heater 12 volt incl. silencer, intake air hose, heat protection hose, tank intake pipe and exhaust corrugated pipeOptionally analogue control unit simple control (PU-5) with rotary control or digital control unit Comfort Control with timer switch5 metre connection cable for control panelSpecial heater bracket for VW T5, optionally with additional installation boxAir outlet for heating air 60 mm1 metre warm air pipe (diameter: 60 mm)60 mm to 90 mm adapterWarm air outlet for rear B-pillarAir duct for B-pillar incl. frameWarm air outlet for B-pillar frontAir ductFixing material (screws, nuts, hose clamp, cable ties)Technical data of the parking heater: Fuel type: dieselHeating capacity: max. 1.8 kW, min. 0.8 kWVolume of heated air: max. 75 m³/h, min. 34 m³/hFuel consumption in operation: max. 0.24 l/h, min. 0.1 l/hPower consumption in operation: max. 29 W, min. 10 WWeight: 3 kg (independent heater)Manual start/stop The AUTOTERM (=Planar) 2D12 is equipped with a height kit. This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heat output decreases proportionally to the amount of oxygen in the air. Roughly speaking, from 2,000 metres the loss of output per 500 m altitude is approx. 5%. Manufacturer tests up to 3,440 m were trouble-free. Up to 4,000 m no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not yet be tested at real altitude. Important:Especially when used at high altitude, the free travel of the fan is extremely important!Route the combustion air intake and exhaust extremely short and with low resistance - i.e. no kinks, no blockage or reduction. It should also be noted that operation beyond 3,000 m is still a technical compromise. Again, care should be taken to ensure that the combustion chamber is properly heated on a regular basis. The chamber must be burnt free of soot deposits. Soot deposits can also form on heaters that are permanently run at the lowest setting. Therefore, the following still applies: No guarantee for sooty combustion chambers! In order to ensure the longevity of the heater, you should also free-burn it occasionally at low levels. The combustion chamber reaches full temperature after running at full load for about half an hour. Normally, no further maintenance is required. In case of extreme loads, e.g. during longer overnight stays at more than 4,000 m, the combustion chamber including the seal set should be cleaned if necessary. We will be happy to advise you: 09181 / 466 644 ☎ https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Parking Heater AUTOTERM (Planar) 2D 12 Volt Complete Set for Land Rover Defender The parking heater set AUTOTERM (Planar) 2D12 for the Land Rover Defender consists of all important components needed for the installation of a parking heater. Included in the delivery are the AUTOTERM 2D 12 Volt parking heater, our Nakatanenga parking heater console, the Nakatanenga mounting plate, a fuel tank extraction, a Webasto air outlet with 60 mm connection, 30 cm warm air pipe and a vibration damper.As a low-priced and powerful alternative to our Webasto parking heater kits, the AUTOTERM (=Planar) 2D parking heater is proving to be a real sales hit. This is partly due to the particularly compact dimensions, which allow installation even in small cars, vans, off-roader motorhomes, construction machinery, boats or in difficult installation situations. In the off-road / 4x4 sector, it is ideally suited for the "typical" off-road vehicles such as Land Rover Defender, Mercedes G or Jeep Wrangler JK.These are only a few of many reasons why we now offer the AUTOTERM (Planar) 2D 12 V parking heater in a clear and comprehensive complete set for the Land Rover Defender at an economical price. For both the Tdi/ Td5 and the Td4, we offer one set each with a perfectly matching accessory kit.You can select different front panel cut-outs for the parking heater console included in the scope of delivery. The associated connections are available in the classic cigarette lighter format (12 V) or as 5 V USB charging sockets for Apple iPhones, navigation devices, iPads and smartphones and are included in the scope of delivery.The parking heater can also be operated while driving.Running time: The AUTOTERM parking heater switches off automatically after 2 hours of operation. However, as soon as you press a button during operation, the parking heater continues to run indefinitely until it is switched off manually.Scope of delivery:- AUTOTERM 2D parking heater 12 volt incl. silencer, intake air hose, heat protection hose, tank intake pipe and corrugated exhaust pipe.- Optionally analogue control unit simple control (PU-5) with rotary control or digital control unit comfort control (PU-29) with time switch- Nakatanenga parking heater console incl. the selected connections- Nakatanenga mounting plate- Fuel filler cap- Webasto air outlet with 60 mm connection, rotatable- 30 cm warm air pipe (diameter: 60 mm)- Vibration damper- Fixing material (screws, nuts, clamps, shrink hose, cable ties)Technical data:- Fuel type: diesel- Heating capacity: max. 1.8 kW, min. 0.8 kW- Volume of heated air: max. 75 m³/h, min. 34 m³/h- Fuel consumption in operation: max. 0.24 l/h, min. 0.1 l/h- Power consumption in operation: max. 29 W, min. 10 W- Weight: 3 kg (independent heater)- Manual start/stop → On the Autoterm.cz site you will find a calculator for the correct dimensioning of the air heater,You can choose between two control elements:- Simple Control (PU-5) element with rotary control: The old PU-10 control element had a relatively inaccessible control surface. Therefore, the reliable control element with rotary control is now the new improved standard of the Planar parking heaters! With the rotary control, you can adjust the heating power of the parking heater and regulate the power of the ventilation in ventilation mode! The PU-5 control element with rotary control can also be purchased separately here.- The digital control element comfort control (PU-29) with timer has an OLED display and an understandable and clear interface.  Temperature, ventilation and power can be configured via the display and the various buttons. With the timer, you can easily set the start of the parking heater to a specific time. The digital control element with timer can also be purchased separately here.Setting options comfort control (PU-29):- Temperature and power (adjustable for the parking heater, the control panel and for an external heater).- Time and date - Operating language (English or Russian)Functions of the timer comfort control (PU-29):- Memory function: save the time so that the parking heater starts at this time every day - Configurable memory locations: Up to 3 different weekdays with different times can be set and saved. The AUTOTERM (=Planar) 2D12 is equipped with an altitude kit.This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heat output decreases proportionally to the amount of oxygen in the air. Roughly speaking, from 2,000 metres the loss of output per 500 m altitude is approx. 5%. Manufacturer tests up to 3,440 m were trouble-free. Up to 4,000 m no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not yet be tested at real altitude. Important:Especially when used at high altitude, the free travel of the fan is extremely important!Route the combustion air intake and exhaust extremely short and with low resistance - i.e. no kinks, no blockage or reduction. It should also be noted that operation beyond 3,000 m is still a technical compromise. Again, care should be taken to ensure that the combustion chamber is properly heated on a regular basis. The chamber must be burnt free of soot deposits. Soot deposits can also form on heaters that are permanently operated at the lowest setting. Therefore, the following still applies: No guarantee for sooty combustion chambers!In order to ensure the longevity of the heater, you should also free-burn it occasionally at low levels. The combustion chamber reaches full temperature after running at full load for about half an hour. Normally, no further maintenance is required. In case of extreme loads, e.g. during longer overnight stays at more than 4,000 m, the combustion chamber including the seal set should be cleaned if necessary.https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

AUTOTERM air 4D (Planar 44D) diesel / air parking heater with additional tank.As a low-priced and powerful alternative to our complete Webasto parking heater kits, we offer the AUTOTERM 4D (formerly Planar 44D) parking heater. The particularly compact dimensions and its heating power of 4 kW allow installation even in small cars, vans off-roaders motor homes, construction machines, boats or under difficult installation situations. The extensive range of accessories supplied simplifies installation. The parking heater has an approval for the European market (ECE mark) and can therefore be installed without registration. The hole pattern here corresponds to the familiar heaters of Eberspächer Airtronic and Webasto AirTop 2000, so that here can be easily replaced without having to drill new holes in the body.All AUTOTERM parking heaters are characterized above all by their durability and reliability with economical consumption. In addition, the heater also has a switchable ventilation function.The parking heater can also be operated while driving. Extensive accessories are available here in our store. The AUTOTERM 4D (prev. 44D) parking heater needs warm air pipes and outlets with 75 mm diameter.Running time: The AUTOTERM parking heater switches off automatically after 2 hours of operation. However, once you press a button during operation, the parking heater will continue to run indefinitely until it is manually turned off.Scope of delivery:- Control element (either simple control PU-5 or Comfort Control depending on your selection.- metering pump- Rubber holder metering pump- Wiring harness metering pump- Wiring harness heater- Intake air hose with integrated silencer- Heat protection hose- End piece exhaust pipe incl. clamp- Tank intake pipe- 5.5 m fuel line- 7 l fuel tank plastic (width: 33 cm + 3 cm intake manifold; height: 26.5 cm + 3 cm bracket + 4.5 cm screw cap, depth: 10 cm)- 300 mm fuel line connector- 1 m corrugated metal exhaust pipe- exhaust silencer- screws, nuts, clamps, heat shrink tubing, cable ties- Instruction manualTechnical data:- Fuel type: diesel- Heating power: max. 4 kw, min. 1 kw- Volume of heated air: max. 120 m³/h, min. 70 m³/h- Fuel consumption in operation: max. 0,514 l/h, min. 0,12 l/h- Power consumption in operation: max. 62 W at 12 V operating voltage, max. 58 W at 24 V operating voltage, min. 10 W- Manual start/stop → On the Autoterm.cz site you can find a calculator for correct air heater sizing,You can choose between two control elements:- PU-5 control element with rotary control: the old PU-10 control element had a relatively inaccessible control surface. Therefore, the reliable control element with rotary control is now the new improved standard of Planar parking heaters! With the rotary control you can adjust the heating power of the parking heater and regulate the power of the ventilation in the ventilation mode! The PU-5 control element with rotary control can also be purchased separately here.- The digital control element Comfort Control with timer has an OLED display and an understandable and clear interface.  Temperature, ventilation and power can be configured via the display and the various buttons. With the new timer, you simply set the start of the parking heater to a specific time. The organic light-emitting diodes of the display ensure a particularly high contrast and low power consumption. The digital control element with timer can also be purchased separately here.Setting options (Comfort Control): Temperature and power (adjustable for the parking heater, the control panel and for an external heater) Time and date Operating language (English or Russian) Functions of the timer (Comfort Control): Memory function: save time so that the parking heater starts at this time every day Configurable memory locations: Up to 3 different days of the week with different times can be set and stored. The AUTOTERM Luft 2D (Planar 2D) is equipped with a height kit!This means that the heater independently reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heating power decreases proportionally to the amount of oxygen in the air. Roughly one can say: From 2,000 meters the loss of power per 500m altitude is about 5%. Manufacturer tests up to 3.440 m were without problems. Up to 4,000 m, no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not be tested in real altitude yet. Please note: Use this 4 kW heater only if this size is really erforgerlich! It is expressly not recommended to permanently turn down the heating. In case of less demand the AUTOTERM Luft 2D (former Planar 2D parking heater) is recommended. If the larger heater is used on a long-term basis on a lower load, the combustion chambers will quickly become sooty - which will cause the heater to fail. https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Planar 2D Auxiliary Vehicle Heater We offer the Planar 2D auxiliary vehicle heater as a well-priced, powerful alternative to our Webasto auxiliary vehicle heater kits. With their compact size and a heater output of 1.8 kW, the Planar 2D is well-suited for fitting to smaller vehicles, vans, off-roaders, camper vans, boats or in confined spaces. It is ideal for 'typical' off-road vehicles like the Land Rover Defender, Mercedes G oder Jeep Wrangler JK. The extensive fitting kit that is supplied with each heater make fitting easy. The Planar 2D can be easily controlled via its analogous control unit, with 8 settings available from 0,8 - 1,8 kW heat output. Available as both, 12 volts or 24 volts, this heater is European market approved (ECE label) and can thus be fitted independet of TUV approval. The parking heater has approval for the European market (ECE test mark) and can therefore be installed without registration. The hole pattern is the same as that of Eberspächer Airtronic and Webasto AirTop 2000 heaters, so that an old unit could easily be replaced without drilling additional holes.A space-saving version with a 90° angle can be found here.  All Planar auxiliary vehicle heaters are extremely long-lasting and durable, as well as very frugal. The heater can also be used while driving. And extensive range of additional equipment is available in our online shop. Attention Defender drivers: Our extensive Planar full-set for Land Rover Defender not only includes everything needed to perfectly fit the heater to your Tdi, Td5 or Td4 Defender, but also offers considerable savings over the individual purchase of all included items. Comes with: - 12 V or 24 V heater- Optionally analogue PU-5 control panel with rotary control or digital Comfort Control control panel with timer- Thomas Magnet P327" dosing pump- Exhaust silencer- Dosing pump rubber holder- Dosing pump wiring harness- Heater wiring harness- Intake air hose with integrated silencer- Heat protection hose- Exhaust pipe end piece + clamp- Tank intake pipe- 5.5 m fuel line- 300 mm fuel line connector- 1 m corrugated metal exhaust pipe- Fastening material (screws, nuts, clamps, heat-shrink tubing, cable ties)- Operating instructions Technical details: ·         fuel: diesel·         heat output: max. 1.8 kw, min. 0.8 kw·         air volume: max. 75 m³/h, min. 34 m³/h·         fuel consumption: max. 0.24 l/h, min. 0.1 l/h·         power drain: max. 29 W, min. 10 W·         manual start/stop→ On the Autoterm.cz website you will find a calculator for the correct dimensioning of the air heater The AUTOTERM Luft 2D (Planar 2D) is equipped with a height kit!This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents shooting of the combustion chamber when the atmospheric oxygen content drops. The max. Heating power drops in proportion to the amount of oxygen in the air. Roughly one can say: From 2.000 meters the loss of power per 500 m height is approx. 5%. Manufacturer tests up to 3.440 m were no problem. No difficulties are to be expected up to 4.000 m. The software itself calculates up to 5.000 m - however, this has not yet been tested in real height. The separately available control unit with timer (optional extra) features a larger OLED display and more intuitive operation. Temperature, ventilation and output can be configured via a display and various switches. An added timer clock allows you to set the heater to a specific time. OLED display provides maximum visibility with minimum power drain.  Possible settings:- temperature and output- time and date- language (English or Russian) Features of the new timer clock:- daily: one fixed time at which the heater starts each day- individual: up to thee different settings with different days and times. The improved new control unit is also available separately.  https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Parking heater set for the VW T5 consists of all important components required for the installation of a parking heater. First and foremost, the set contains the AUTOTERM (=Planar) 2D12 parking heater, which is celebrated as an affordable and powerful alternative to Webasto and Eberspächer parking heaters. In addition to the heater holder with installation box, which can already be ordered individually and which was specially designed for the installation of the Planar parking heater in the VW T5, with this set we put together a comprehensive package for you with a matching hose clamp, fuel line, air duct, a warm air outlet and much more. As some components for the B-pillar vary depending on the vehicle model, please select the matching set for your VW T5 estate / panel van OR Multivan / Shuttle / California. Please note: This set is not suitable for vehicles with a partition wall! Scope of delivery: AUTOTERM 2D parking heater 12 volt incl. silencer, intake air hose, heat protection hose, tank intake pipe and exhaust corrugated pipeOptionally analogue control unit simple control (PU-5) with rotary control or digital control unit Comfort Control with timer switch5 metre connection cable for control panelSpecial heater bracket for VW T5, optionally with additional installation boxAir outlet for heating air 60 mm1 metre warm air pipe (diameter: 60 mm)60 mm to 90 mm adapterWarm air outlet for rear B-pillarAir duct for B-pillar incl. frameWarm air outlet for B-pillar frontAir ductFixing material (screws, nuts, hose clamp, cable ties)Technical data of the parking heater: Fuel type: dieselHeating capacity: max. 1.8 kW, min. 0.8 kWVolume of heated air: max. 75 m³/h, min. 34 m³/hFuel consumption in operation: max. 0.24 l/h, min. 0.1 l/hPower consumption in operation: max. 29 W, min. 10 WWeight: 3 kg (independent heater)Manual start/stop The AUTOTERM (=Planar) 2D12 is equipped with a height kit. This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heat output decreases proportionally to the amount of oxygen in the air. Roughly speaking, from 2,000 metres the loss of output per 500 m altitude is approx. 5%. Manufacturer tests up to 3,440 m were trouble-free. Up to 4,000 m no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not yet be tested at real altitude. Important:Especially when used at high altitude, the free travel of the fan is extremely important!Route the combustion air intake and exhaust extremely short and with low resistance - i.e. no kinks, no blockage or reduction. It should also be noted that operation beyond 3,000 m is still a technical compromise. Again, care should be taken to ensure that the combustion chamber is properly heated on a regular basis. The chamber must be burnt free of soot deposits. Soot deposits can also form on heaters that are permanently run at the lowest setting. Therefore, the following still applies: No guarantee for sooty combustion chambers! In order to ensure the longevity of the heater, you should also free-burn it occasionally at low levels. The combustion chamber reaches full temperature after running at full load for about half an hour. Normally, no further maintenance is required. In case of extreme loads, e.g. during longer overnight stays at more than 4,000 m, the combustion chamber including the seal set should be cleaned if necessary. We will be happy to advise you: 09181 / 466 644 ☎ https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Parking Heater AUTOTERM (Planar) 2D 12 Volt Complete Set for Land Rover Defender The parking heater set AUTOTERM (Planar) 2D12 for the Land Rover Defender consists of all important components needed for the installation of a parking heater. Included in the delivery are the AUTOTERM 2D 12 Volt parking heater, our Nakatanenga parking heater console, the Nakatanenga mounting plate, a fuel tank extraction, a Webasto air outlet with 60 mm connection, 30 cm warm air pipe and a vibration damper.As a low-priced and powerful alternative to our Webasto parking heater kits, the AUTOTERM (=Planar) 2D parking heater is proving to be a real sales hit. This is partly due to the particularly compact dimensions, which allow installation even in small cars, vans, off-roader motorhomes, construction machinery, boats or in difficult installation situations. In the off-road / 4x4 sector, it is ideally suited for the "typical" off-road vehicles such as Land Rover Defender, Mercedes G or Jeep Wrangler JK.These are only a few of many reasons why we now offer the AUTOTERM (Planar) 2D 12 V parking heater in a clear and comprehensive complete set for the Land Rover Defender at an economical price. For both the Tdi/ Td5 and the Td4, we offer one set each with a perfectly matching accessory kit.You can select different front panel cut-outs for the parking heater console included in the scope of delivery. The associated connections are available in the classic cigarette lighter format (12 V) or as 5 V USB charging sockets for Apple iPhones, navigation devices, iPads and smartphones and are included in the scope of delivery.The parking heater can also be operated while driving.Running time: The AUTOTERM parking heater switches off automatically after 2 hours of operation. However, as soon as you press a button during operation, the parking heater continues to run indefinitely until it is switched off manually.Scope of delivery:- AUTOTERM 2D parking heater 12 volt incl. silencer, intake air hose, heat protection hose, tank intake pipe and corrugated exhaust pipe.- Optionally analogue control unit simple control (PU-5) with rotary control or digital control unit comfort control (PU-29) with time switch- Nakatanenga parking heater console incl. the selected connections- Nakatanenga mounting plate- Fuel filler cap- Webasto air outlet with 60 mm connection, rotatable- 30 cm warm air pipe (diameter: 60 mm)- Vibration damper- Fixing material (screws, nuts, clamps, shrink hose, cable ties)Technical data:- Fuel type: diesel- Heating capacity: max. 1.8 kW, min. 0.8 kW- Volume of heated air: max. 75 m³/h, min. 34 m³/h- Fuel consumption in operation: max. 0.24 l/h, min. 0.1 l/h- Power consumption in operation: max. 29 W, min. 10 W- Weight: 3 kg (independent heater)- Manual start/stop → On the Autoterm.cz site you will find a calculator for the correct dimensioning of the air heater,You can choose between two control elements:- Simple Control (PU-5) element with rotary control: The old PU-10 control element had a relatively inaccessible control surface. Therefore, the reliable control element with rotary control is now the new improved standard of the Planar parking heaters! With the rotary control, you can adjust the heating power of the parking heater and regulate the power of the ventilation in ventilation mode! The PU-5 control element with rotary control can also be purchased separately here.- The digital control element comfort control (PU-29) with timer has an OLED display and an understandable and clear interface.  Temperature, ventilation and power can be configured via the display and the various buttons. With the timer, you can easily set the start of the parking heater to a specific time. The digital control element with timer can also be purchased separately here.Setting options comfort control (PU-29):- Temperature and power (adjustable for the parking heater, the control panel and for an external heater).- Time and date - Operating language (English or Russian)Functions of the timer comfort control (PU-29):- Memory function: save the time so that the parking heater starts at this time every day - Configurable memory locations: Up to 3 different weekdays with different times can be set and saved. The AUTOTERM (=Planar) 2D12 is equipped with an altitude kit.This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heat output decreases proportionally to the amount of oxygen in the air. Roughly speaking, from 2,000 metres the loss of output per 500 m altitude is approx. 5%. Manufacturer tests up to 3,440 m were trouble-free. Up to 4,000 m no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not yet be tested at real altitude. Important:Especially when used at high altitude, the free travel of the fan is extremely important!Route the combustion air intake and exhaust extremely short and with low resistance - i.e. no kinks, no blockage or reduction. It should also be noted that operation beyond 3,000 m is still a technical compromise. Again, care should be taken to ensure that the combustion chamber is properly heated on a regular basis. The chamber must be burnt free of soot deposits. Soot deposits can also form on heaters that are permanently operated at the lowest setting. Therefore, the following still applies: No guarantee for sooty combustion chambers!In order to ensure the longevity of the heater, you should also free-burn it occasionally at low levels. The combustion chamber reaches full temperature after running at full load for about half an hour. Normally, no further maintenance is required. In case of extreme loads, e.g. during longer overnight stays at more than 4,000 m, the combustion chamber including the seal set should be cleaned if necessary.https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment