B-Rack Mid Top DK PickUp Bed Rack horntools Double Cab One system designed for all pickups and all needs. Whether camper, craftsmanor hunter - the B-Rack was developed as a modular system. Made of high-quality aluminum. The B-Rack is not only very light, but also extremely rigid.Suitable for midsize pickups such as: Nissan Navara Ford Ranger / Raptor Mitsubishi L200 Fiat Fullback Mercedes X-Class US pickups and special vehicles can be tested on request.Attention:If the system remains permanently installed, the following clearance angles must be observed for the third brake light:10° left and right, as well as 10° up and 5° down. If these clearance angles are not adheredto, the brake light must be reinstalled at the rear of the vehicle, taking into account the limit dimensions of ECE R48.The standard third brake light must then be deactivated and the lens blackened.fact: 4 different heights and 2 different lengths For double cabins and ex-cabs Simply take it with you when changing vehicles Flexible construction and width adjustable Numerous mounting options for holders and accessories Extensive range of accessories such as inserts and boxes incl. optionally installable PHBRSIRA cross brace (see installation instructions) High-quality coated aluminum Weight approx. 27 kg Notice:Due to manufacturer tolerances in the area of ​​the loading areasIn individual cases, our products may not fit exactly.With the Mercedes X-Class and the Nissan Navara, the side-mountedlashing rails must be dismantled in order to mount the B-Rack!

Pickup Bed Rack System - B-RACK  This version of the B-RACK was specially developed for the Isuzu DMAX and VW Amarok, so that the B-RACK overlay roof rackcan be mounted on the vehicle. The 45 version of the B-RACK is normally used for this.But the DMAX has a higher cabin and because of this we have developed a special solution here.Our all-rounder, whether for campers, craftsmenor hunters - the B-Rack was developed as a modular system.The material consists of high-quality aluminum, making it very light and extremely stiff.Suitable for midsize pickups such as: Isuzu Dmax VW Amarok Attention:For mounting on a VW Amarok, it requires its own mounting frame: PHBRSUFR135VWAM B- Rack mounting frames for Volkswagen® AmarokUS pickups and special vehicles can be checked upon request.Caution:If the system remains permanently installed, the following clearance angles must be observed for the third brake light:10° to the right and left, as well as 10° up and 5° down. If these clearance angles are not observed,the brake light must be reinstalled at the rear of the vehicle, taking into account the limit dimensions of ECE R48.The standard third brake light must then be deactivated and the lens blackened. fact: 4 different heights and 2 different lengths For double cabins and ex-cabs Simply take it with you when changing vehicles Flexible construction and width adjustable Numerous mounting options for holders and accessories Extensive range of accessories such as inserts and boxes incl. optionally installable PHBRSIRA cross brace (see installation instructions) High-quality coated aluminum Weight approx. 27 kg Note:Due to manufacturer tolerances in the area of ​​the loading areas, in individual cases our products may not fit exactly.With the Mercedes X-Class and the Nissan Navara, thelashing rails mounted on the side must be dismantled in order to mount the B-Rack!

B-Rack Mid Top Plus XtraCab PickUp 50cmx155cm Bed Rack horntools Extra Cab Pickup Bed Rack System - B-RACKOne system designed for all pickups and all needs. Whether camper, craftsmanor hunter - the B-Rack was developed as a modular system. Made of high-quality aluminum, the B-Rack is not only very light, but also extremely rigid.Suitable for midsize pickups such as:     VW Amarok     Isuzu Dmax For VW Amarok you need the mounting frame PHBRSUFR135VWAM US pickups and special vehicles can be inspected upon request.Caution:If the system remains permanently installed, the following clearance angles must be observed for the third brake light:10° to the right and left, as well as 10° up and 5° down. If these clearance angles are not adheredto, the brake light must be reinstalled at the rear of the vehicle, taking into account the limit dimensions of ECE R48.The standard third brake light must then be deactivated and the lens blackened. fact:     3 different heights and 2 different lengths     For double cabins and ex-cabs     Simply take it with you when changing vehicles     Flexible construction and width adjustable     Numerous mounting options for holders and accessories     Extensive range of accessories such as inserts and boxes     incl. optionally installable PHBRSIRA cross brace (see installation instructions)     High-quality coated aluminum     Weight approx. 29 kg Notice:Due to manufacturer tolerances in the area of ​​the loading areasIn individual cases, our products may not fit exactly.With the Mercedes X-Class and the Nissan Navara, the lashing rails mounted on the side must be dismantled in order to mount the B-Rack!

B-Rack Mid Top XtraCab PickUp 45cmx155cm Bed Rack horntools Extra Cab Pickup Bed Rack System - B-RACKOne system designed for all pickups and all needs. Whether camper, craftsmanor hunter - the B-Rack was developed as a modular system. Made of high-quality aluminum. The B-Rack is not only very light, but also extremely rigid.Suitable for pickups such as:    Nissan Navara Ford Ranger / Raptor Mitsubishi L200 Fiat Fullback Mercedes X-Klasse US pickups and special vehicles can be inspected upon request. Caution:If the system remains permanently installed, the following clearance angles must be observed for the third brake light:10° to the right and left, as well as 10° up and 5° down. If these clearance angles are not adheredto, the brake light must be reinstalled at the rear of the vehicle, taking into account the limit dimensions of ECE R48.The standard third brake light must then be deactivated and the lens blackened. fact:  3 different heights and 2 different lengths  For double cabins and ex-cabs  Simply take it with you when changing vehicles  Flexible construction and width adjustable  Numerous mounting options for holders and accessories  Extensive range of accessories such as inserts and boxes  High-quality coated aluminum  Weight approx. 29 kg Notice:Due to manufacturer tolerances in the area of ​​the loading areasIn individual cases, our products may not fit exactly.With the Mercedes X-Class and the Nissan Navara, thelashing rails mounted on the side must be dismantled in order to mount the B-Rack!

B-Rack roof rack overlay for Mid Top B-Rack Pickup Bed Rack System - B-RACKOne system designed for all pickups and all needs. Whether camper, craftsmanor hunter - the B-Rack was developed as a modular system. Made of high-quality aluminum, the B-Rack is not only very light, but also extremely rigid.Overlay roof rack for MidTop B-Rack basic rackThe ideal addition to the basic rack for roof tents, long goods and other bulky loads.The overlay roof rack is designed in such a way that it still remains in place even when the chassis is foldedhas enough distance to the cabin - despite the load. We used the space on the backand installed 2 waterproof and dustproof flaps to form a large compartment.There are numerous mounting and lashing options on the entire carrier.Two designated mounting locations for work lights are located on the front of the overlay.Notice: ATTENTION: This is only the overlay roof rack! The B-Rack basic carrier must be purchased separately. When setting up, care must be taken to ensure that there is always at least 5cm space between the overlay andthe vehicle. In the case of vehicles with a railing, this may have to be dismantled. The original antenna can no longer be used with the roof rack. You can swap it for a flexible or short antenna. Please make sure  beforehand whether the replacement antenna is compatible. Due to manufacturer tolerances in the area of ​​the loading areas, in individual cases our products may not fit exactly. The slightly higher B-Rack: HBR50-135 is required for the Isuzu DMAX.  

CargoBear – Querbügel schräg / niedrig Passend für CargoBear Windschott schräg  Material:  Aluminium, schwarz matt pulverbeschichtet RAL 9005 inkl. Befestigungsmaterial Querbügel schräg/niedrig ist die passende Halterung für Windschott schräg geeignet für alle CargoBear 1 + 2  Dachträger! nur auf Höhe A-Säule montierbar geeignet für die Montage von Lampen und Scheinwerfer

CargoBear Quick mounting rails for various roof racks If you use your roof tent frequently or want to mount it on different vehicles, our quick mount system for roof tents is an enormously practical and time-saving solution. Whether CargoBear, FrontRunner or other roof rack systems, fastening our practical, two-part mounting rails is a question of minutes. Each rail’s bottom is attached to the carrier and the top to the underside of the roof tent, thereby providing and easy to reach connection that is equally quick to fasten or loosen again. That way, you only drive your tent around when you're actually going camping. As a general rule, two rails will be sufficient for mounting most tents. However, for larger/longer hard-shell tents, for example, we recommend using three rails. The black powder-coated bottom part (on the roof rack) of each pair of rails is attached to the stainless steel top part (on the roof tent) with two to four screws.Compared to the old frame solution, the enormously space-saving quick-change rails are very easy to pack – leading to significantly lower shipping costs compared to the expensive special delivery charges for the old system.You are not sure whether a roof tent can be mounted on your vehicle? We are happy to help and advise you! So far, we have found the perfect solution for almost every vehicle. Length: 113cmHeight: 5,5cm Just get in touch at +49 (0) 9181 466 644 Please note:the basic set consists of 2 rails with 2 upper and 2 lower parts each (4 parts).Normally, the basic set is sufficient for the assembly.E.g. for large roof tents you can mount an additional rail (2 parts) for more stability.

Rear ladder for Suzuki Jimny 2 type GJ BJ 2018 / HJ Boxier, tougher and even more capable, that’s the Suzuki Jimny 2 (GJ/HJ MY 2019). Even if cargo space has grown considerably in comparison with the previous model, optimizing your usable load capacity is still crucial if you want to get the most out of this little giant. Considering the limited interior that means first and foremost to use the roof space to the full extent: either with our own dedicated CargoBear system for the Jimny or any other conventional roof rails, bars or racks. Whatever solution you prefer, our light and strong aluminum ladder makes accessing the roof area a lot easier. Climbing to the rooftop is safer, more comfortable and allows for stress-free loading, fastening or strapping down of your cargo. The ladder is mounted on the tailgate only and has no connection with the roof or the rack, making it ideal for all kinds of carrier systems. Additionally, there is no need to drill holes either as the ladder is custom-designed to fit existing mounting points and screw holes: on the spare wheel mount, the tailgate’s drip rail and the bottom right door hinge. This also allows for quick and easy de-installation without damage or marks. The ladder is made from high-quality aluminum and features black powder coating – a perfect match for our modular CargoBear roof rack system.

Rear ladder suitable for Land Rover Defender 90/110 allows for easy access to roof rack. This ladder is supplied WITHOUT an additional rear step. This can be ordered separately. The ladder is produced for us from high-grade aluminium alloy and WIG welded, resulting in a very lightweight (1.8 kg only) and durable ladder. The steps feature an anti-slip design. Available with or without black powder coating. Please choose.

Rear ladder for Mercedes G With this ladder you have easy and safe access to your roof rack. Mounting on the left side. You can find an article for mounting on the right-hand side here. Material: aluminum, powder coated black satin finish Note:With W460 the filler neck is accessible through the ladder.

This rear ladder with additional step for rear crossmember fits Land Rover Defender 90/110 and allows easy access to the roof rack. This ladder is produced for us from high-grade aluminium alloy and TIG welded, resulting in a very lightweight (only 1.8 kg) and durable product. Steps are anti-slip. The ladder and the aluminum step are powder-coated in black. 

Roof rack NAVIS spoiler RAIL & FLAT PickUp roof rail Alu black:The spoiler reduces the wind noise and is suitable for all NAVIS roof racks. Roof rack railing for NAVIS FLAT PickUp roof rail aluminum black:The matching side rail for the roof rack NAVIS FLAT - suitable for all PickUp models.2 pieces (1x left and 1x right)Color: Black

Thule toggle nuts, lockable Protect your roof racks from theft! The ideal addition to our Thule racks for Land Rover Defender and Land Rover Discovery 1 / 2 are the lockable toggle nuts.The set contains 4 tommy nuts with keyed alike stainless steel locks and matching keys. The locks are compatible with the Thule One Key System if other Thule products are used.

Thule roof bar for Land Rover vehicles Thule roof bar for Land Rover vehicles, optionally for Land Rover Defender or Land Rover Discovery 1 / 2, consisting of two crossbars and feet in suitable height for rain gutter mounting.Thule roof racks or roof bars have been synonymous with quality and safety for decades, even under tough conditions. They are therefore ideally suited for mounting roof tents, roof boxes, equipment carriers of all kinds and much more.Technical data:    Load capacity: 100 kg (dynamic, i.e. while driving).    Max. roof load Roof load: according to vehicle manufacturer's specifications    Material feet: sheet steel, galvanised, powder coated, Pebax coating    Material of crossbar: Square steel tube, powder-coated    Assembly: Quick assembly without tools using central nut    Lockable: No, but can be retrofitted with lockable tommy nuts    Foot height: Suitable for Discovery I / II or Defender 90 / 110 / 130    Length of cross struts: 150 cm    Foot height: 20 cmPlease note the maximum roof load of the vehicle according to the manufacturer's specifications!Please select your vehicle type.

Nützliches und funktionales Zubehör für Pickup Bed Rack System - B-RACK Ein System, entwickelt für alle Pickups und alle Anforderungen. Egal ob Camper, Handwerkeroder Jäger - das B-Rack wurde als Modular System entwickelt. Aus hochwertigem Aluminiumgefertigt ist das B-Rack nicht nur sehr leicht, sondern auch extrem steif.B-RACK Montagerahmen Volkswagen Amarok GrundträgerPart B-Rack unterer Rahmen Volkswagen® Amarok 135cm Subframe 2 Stk. im SetMontagerahmen speziell für VW Amarok - B-RACKnötig zur Montage des Grundträgers HBR50-135 oder HBR50-155Aufgrund der Ladeflächenform des VW Amaroks, benötigt es diesen extra Montagerahmen.Das B-Rack kann NICHT ohne diesen Rahmen auf dem Fahrzeug montiert werden!Passend für VW Amarok Doppelkabiner von 2010-2020.Bremsleuchte für B-RackB-Rack Bremsleuchte Tail LightsDie passende Bremsleuchte für dein B-Rack. Somit bist du und dein Hintermann sicher unterwegs.Wenn die dritte Bremsleuchte durch den Grundträger verdeckt ist, sollte diese Bremsleuchte angebracht werdenB-Rack Front Durchreiche und Auszug Halterung Track Pad MountPickup Bed Rack System - B-RACKFront Durchreiche und Halterung für Auszüge oder KistenMultifunktionale Durchreiche, die entweder als Halterung für Kisten oder Schubladenauszügen dienen kann, oder einfach als weitere Verstaumöglichkeit für Camping Zubehör, oder Werkzeug.Hinweis: Aufgrund von Herstellertoleranzen im Bereich der Ladeflächen kann es in Einzelfällen zu einer ungenauen Passform unserer Produkte kommen. B-Rack Gullwing BoxAbsperrbare Gullwing Box / Toolbox Verschiebbar am Träger. Für Werkzeug, Kompressor oder anderes Equipment das auf einer Reise oder bei der Arbeit einfach nicht fehlen darf.Maße: 50x50x37cmDie Box passt nur wenn eines dieser B-Racks verbaut ist:HBR45-135HBR45-155B-Rack Hebe und Zurröse Tow Strap down EyeDiese Ösen sind der perfekte Zusatz für dein B-Rack.Im Set sind 4 Hebe und Zurrösen enthalten.B-Rack Markisen Montage SystemAwning Mount System 2 Stk. im SetDank diesem System können Markisen einfach und unkompliziert an deinemB-Rack befestigt werden. Im Set sind zwei Halterungen enthalten.B-Rack Sand Blech und Langgut Halterung Track Pad MountDas Ideale Zubehör für dein B-Rack um Langgut oder Ähnliches sicher zu verstauen.Dank des durchdachten Systems beträgt die Montagedauer nur ca. 15 Minuten.Der Langguthalter ist nur mit den 135cm langen B-Racks kombinierbar!B-Rack Seilwindensystem Gamma 1,6 t  , 12Volt mit KunststoffseilWir haben auch für unser B-Rack ein Seilwindensystem entwickelt, dass ideal auf desen Bedürfnisseangepasst ist. Mit ihren 1,6 Tonnen Zugkraft bietet die Seilwinde genug Kraft, um dich bei deinen Aufgabenauf der Jagd, dem Campen oder Handwerken zu unterstützen.Das Windensystem ist für maximal 100kg ausgelegt um Schäden am Aufbau oder der Ladefläche zu vermeiden.